Abstract: This paper describes the development, modeling, and
testing of skyhook and MiniMax control strategies of semi-active
suspension. The control performances are investigated using
Matlab/Simulink [1], with a two-degree-of-freedom quarter car semiactive
suspension system model. The comparison and evaluation of
control result are made using software-in-the-loop simulation (SILS)
method. This paper also outlines the development of a hardware-inthe-
loop simulation (HILS) system. The simulation results show that
skyhook strategy can significantly reduce the resonant peak of body
and provide improvement in vehicle ride comfort. Otherwise,
MiniMax strategy can be employed to effectively improve drive
safety of vehicle by influencing wheel load. The two strategies can
be switched to control semi-active suspension system to fulfill
different requirement of vehicle in different stages.
Abstract: A two-dimensional numerical simulation of crossflow
around four cylinders in an in-line rectangular configuration is
studied by using the lattice Boltzmann method (LBM). Special
attention is paid to the effect of the spacing between the cylinders.
The Reynolds number ( Re ) is chosen to be e 100 R = and the
spacing ratio L / D is set at 0.5, 1.5, 2.5, 4.0, 5.0, 6.0, 7.0, 8.0, 9.0
and 10.0. Results show that, as in the case of four cylinders in an inline
rectangular configuration , flow fields show four different
features depending on the spacing (single square cylinder, stable
shielding flow, wiggling shielding flow and a vortex shedding flow)
are observed in this study. The effects of spacing ratio on physical
quantities such as mean drag coefficient, Strouhal number and rootmean-
square value of the drag and lift coefficients are also presented.
There is more than one shedding frequency at small spacing ratios.
The mean drag coefficients for downstream cylinders are less than
that of the single cylinder for all spacing ratios. The present results
using the LBM are compared with some existing experimental data
and numerical studies. The comparison shows that the LBM can
capture the characteristics of the bluff body flow reasonably well and
is a good tool for bluff body flow studies.
Abstract: Developed tool is one of system tools for easier access to various scientific areas and real time interactive learning between
lecturer and for hearing impaired students. There is no demand for the lecturer to know Sign Language (SL). Instead, the new software
tools will perform the translation of the regular speech into SL, after
which it will be transferred to the student. On the other side, the
questions of the student (in SL) will be translated and transferred to
the lecturer in text or speech. One of those tools is presented tool. It-s
too for developing the correct Speech Visemes as a root of total communication method for hearing impared students.
Abstract: The interactions between input/output variables are a very common phenomenon encountered in the design of multi-loop controllers for interacting multivariable processes, which can be a serious obstacle for achieving a good overall performance of multiloop control system. To overcome this impediment, the decomposed dynamic interaction analysis is proposed by decomposing the multiloop control system into a set of n independent SISO systems with the corresponding effective open-loop transfer function (EOTF) within the dynamic interactions embedded explicitly. For each EOTF, the reduced model is independently formulated by using the proposed reduction design strategy, and then the paired multi-loop proportional-integral-derivative (PID) controller is derived quite simply and straightforwardly by using internal model control (IMC) theory. This design method can easily be implemented for various industrial processes because of its effectiveness. Several case studies are considered to demonstrate the superior of the proposed method.
Abstract: Large metal and concrete structures suffer by various kinds of deterioration, and accurate prediction of the remaining life is important. This paper informs about two methods for its assessment. One method, suitable for steel bridges and other constructions exposed to fatigue, monitors the loads and damage accumulation using information systems for the operation and the finite element model of the construction. In addition to the operation load, the dead weight of the construction and thermal stresses can be included into the model. The second method is suitable for concrete bridges and other structures, which suffer by carbonatation and other degradation processes, driven by diffusion. The diffusion constant, important for the prediction of future development, can be determined from the depth-profile of pH, obtained by pH measurement at various depths. Comparison with measurements on real objects illustrates the suitability of both methods.
Abstract: Data mining can be called as a technique to extract
information from data. It is the process of obtaining hidden
information and then turning it into qualified knowledge by statistical
and artificial intelligence technique. One of its application areas is
medical area to form decision support systems for diagnosis just by
inventing meaningful information from given medical data. In this
study a decision support system for diagnosis of illness that make use
of data mining and three different artificial intelligence classifier
algorithms namely Multilayer Perceptron, Naive Bayes Classifier and
J.48. Pima Indian dataset of UCI Machine Learning Repository was
used. This dataset includes urinary and blood test results of 768
patients. These test results consist of 8 different feature vectors.
Obtained classifying results were compared with the previous studies.
The suggestions for future studies were presented.
Abstract: Globalization and therefore increasing tight competition among companies, have resulted to increase the importance of making well-timed decision. Devising and employing effective strategies, that are flexible and adaptive to changing market, stand a greater chance of being effective in the long-term. In other side, a clear focus on managing the entire product lifecycle has emerged as critical areas for investment. Therefore, applying wellorganized tools to employ past experience in new case, helps to make proper and managerial decisions. Case based reasoning (CBR) is based on a means of solving a new problem by using or adapting solutions to old problems. In this paper, an adapted CBR model with k-nearest neighbor (K-NN) is employed to provide suggestions for better decision making which are adopted for a given product in the middle of life phase. The set of solutions are weighted by CBR in the principle of group decision making. Wrapper approach of genetic algorithm is employed to generate optimal feature subsets. The dataset of the department store, including various products which are collected among two years, have been used. K-fold approach is used to evaluate the classification accuracy rate. Empirical results are compared with classical case based reasoning algorithm which has no special process for feature selection, CBR-PCA algorithm based on filter approach feature selection, and Artificial Neural Network. The results indicate that the predictive performance of the model, compare with two CBR algorithms, in specific case is more effective.
Abstract: The success of IT-projects concerning the
implementation of business application Software is strongly
depending upon the application of an efficient requirements
management, to understand the business requirements and to realize
them in the IT. But in fact, the Potentials of the requirements
management are not fully exhausted by small and medium sized
enterprises (SME) of the IT sector. To work out recommendations for
action and furthermore a possible solution, allowing a better exhaust
of potentials, it shall be examined in a scientific research project,
which problems occur out of which causes. In the same place, the
storage of knowledge from the requirements management, and its
later reuse are important, to achieve sustainable improvements of the
competitive of the IT-SMEs. Requirements Engineering is one of the
most important topics in Product Management for Software to
achieve the goal of optimizing the success of the software product.
Abstract: Photo-crosslinked rice starch-based biodegradable
films were prepared by casting film-solution on leveled trays and
ultra violet (UV) irradiation was applied for 10 minute. The effect of
the content (3%, 6% and 9 wt. %)of photosensitiser (sodium
benzoate) on mechanical properties, water vapor permeability (WVP)
and structural properties of rice starch films were investigated. The
tensile strength increased while elongation at break and water
resistance properties of rice starch films decreased with addition and
increasing content of photosensitiser. The % crystallinity of rice
starch films were decreased when the content of photosensitiser
increased and UV were applied. The results showed that the
carboxylate group band of sodium benzoate was found in the FTIR
spectrum of rice starch films and found that incorporation of 6% of
photosensitiser into the films showed a higher absorption band of
resulted films. This result pointed out the highest interaction between
starch molecules was occurred.
Abstract: This paper deals with condition monitoring of electric switch machine for railway points. Point machine, as a complex electro-mechanical device, switch the track between two alternative routes. There has been an increasing interest in railway safety and the optimal management of railway equipments maintenance, e.g. point machine, in order to enhance railway service quality and reduce system failure. This paper explores the development of Kolmogorov- Smirnov (K-S) test to detect some point failures (external to the machine, slide chairs, fixing, stretchers, etc), while the point machine (inside the machine) is in its proper condition. Time-domain stator Current signatures of normal (healthy) and faulty points are taken by 3 Hall Effect sensors and are analyzed by K-S test. The test is simulated by creating three types of such failures, namely putting a hard stone and a soft stone between stock rail and switch blades as obstacles and also slide chairs- friction. The test has been applied for those three faults which the results show that K-S test can effectively be developed for the aim of other point failures detection, which their current signatures deviate parametrically from the healthy current signature. K-S test as an analysis technique, assuming that any defect has a specific probability distribution. Empirical cumulative distribution functions (ECDF) are used to differentiate these probability distributions. This test works based on the null hypothesis that ECDF of target distribution is statistically similar to ECDF of reference distribution. Therefore by comparing a given current signature (as target signal) from unknown switch state to a number of template signatures (as reference signal) from known switch states, it is possible to identify which is the most likely state of the point machine under analysis.
Abstract: In recent years, the number of natural disasters in Laos has a trend to increase, especially the disaster of flood. To make a flood plan risk management in the future, it is necessary to understand and analyze the characteristics of the rainfall and Mekong River level data. To reduce the damage, this paper presents the flood risk analysis in Luangprabang and Vientiane, the prefecture of Laos. In detail, the relationship between the rainfall and the Mekong River level has evaluated and appropriate countermeasure for flood was discussed.
Abstract: In this paper, we show that the association of the PI
regulators for the speed and stator currents with a control strategy
using the linearization by state feedback for an induction machine
without speed sensor, and with an adaptation of the rotor resistance.
The rotor speed is estimated by using the model reference adaptive
system approach (MRAS). This method consists of using two
models: The first is the reference model and the second is an
adjustable one in which two components of the stator flux, obtained
from the measurement of the currents and stator voltages are
estimated. The estimated rotor speed is then obtained by canceling
the difference between stator-flux of the reference model and those
of the adjustable one. Satisfactory results of simulation are obtained
and discussed in this paper to highlight the proposed approach.
Abstract: This paper gives an overview of a deep drawing
process by pressurized liquid medium separated from the sheet by a
rubber diaphragm. Hydroforming deep drawing processing of sheet
metal parts provides a number of advantages over conventional
techniques. It generally increases the depth to diameter ratio possible
in cup drawing and minimizes the thickness variation of the drawn
cup. To explore the deformation mechanism, analytical and
numerical simulations are used for analyzing the drawing process of
an AA6061-T4 blank. The effects of key process parameters such as
coefficient of friction, initial thickness of the blank and radius
between cup wall and flange are investigated analytically and
numerically. The simulated results were in good agreement with the
results of the analytical model. According to finite element
simulations, the hydroforming deep drawing method provides a more
uniform thickness distribution compared to conventional deep
drawing and decreases the risk of tearing during the process.
Abstract: The intrusion detection problem has been frequently studied, but intrusion detection methods are often based on a single point of view, which always limits the results. In this paper, we introduce a new intrusion detection model based on the combination of different current methods. First we use a notion of distance to unify the different methods. Second we combine these methods using the Pearson correlation coefficients, which measure the relationship between two methods, and we obtain a combined distance. If the combined distance is greater than a predetermined threshold, an intrusion is detected. We have implemented and tested the combination model with two different public data sets: the data set of masquerade detection collected by Schonlau & al., and the data set of program behaviors from the University of New Mexico. The results of the experiments prove that the combination model has better performances.
Abstract: The Deoxyribonucleic Acid (DNA) which is a doublestranded helix of nucleotides consists of: Adenine (A), Cytosine (C), Guanine (G) and Thymine (T). In this work, we convert this genetic code into an equivalent digital signal representation. Applying a wavelet transform, such as Haar wavelet, we will be able to extract details that are not so clear in the original genetic code. We compare between different organisms using the results of the Haar wavelet Transform. This is achieved by using the trend part of the signal since the trend part bears the most energy of the digital signal representation. Consequently, we will be able to quantitatively reconstruct different biological families.
Abstract: Fuzzy C-means Clustering algorithm (FCM) is a
method that is frequently used in pattern recognition. It has the
advantage of giving good modeling results in many cases, although,
it is not capable of specifying the number of clusters by itself. In
FCM algorithm most researchers fix weighting exponent (m) to a
conventional value of 2 which might not be the appropriate for all
applications. Consequently, the main objective of this paper is to use
the subtractive clustering algorithm to provide the optimal number of
clusters needed by FCM algorithm by optimizing the parameters of
the subtractive clustering algorithm by an iterative search approach
and then to find an optimal weighting exponent (m) for the FCM
algorithm. In order to get an optimal number of clusters, the iterative
search approach is used to find the optimal single-output Sugenotype
Fuzzy Inference System (FIS) model by optimizing the
parameters of the subtractive clustering algorithm that give minimum
least square error between the actual data and the Sugeno fuzzy
model. Once the number of clusters is optimized, then two
approaches are proposed to optimize the weighting exponent (m) in
the FCM algorithm, namely, the iterative search approach and the
genetic algorithms. The above mentioned approach is tested on the
generated data from the original function and optimal fuzzy models
are obtained with minimum error between the real data and the
obtained fuzzy models.
Abstract: Tumor cells have an invasive and metastatic phenotype
that is the main cause of death for cancer patients. Tumor
establishment and penetration consists of a series of complex
processes involving multiple changes in gene expression. In this study,
intraperitoneal administration of a high concentration of ascorbic acid
inhibited tumor establishment and decreased tumor mass in BALB/C
mice implanted with S-180 sarcoma cancer cells. To identify proteins
involved in the ascorbic acid-mediated inhibition of tumor
progression, changes in the tumor proteome associated with ascorbic
acid treatment of BALB/C mice implanted with S-180 were
investigated using two-dimensional gel electrophoresis and mass
spectrometry. Twenty protein spots were identified whose expression
was different between control and ascorbic acid treatment groups.
Abstract: This study aimed at assessing whether and to what extent moral judgment and behaviour were: 1. situation-dependent; 2. selectively dependent on cognitive and affective components; 3. influenced by gender and age; 4. reciprocally congruent. In order to achieve these aims, four different types of moral dilemmas were construed and five types of thinking were presented for each of them – representing five possible ways to evaluate the situation. The judgment criteria included selfishness, altruism, sense of justice, and the conflict between selfishness and the two moral issues. The participants were 250 unpaid volunteers (50% male; 50% female) belonging to two age-groups: young people and adults. The study entailed a 2 (gender) x 2 (age-group) x 5 (type of thinking) x 4 (situation) mixed design: the first two variables were betweensubjects, the others were within-subjects. Results have shown that: 1. moral judgment and behaviour are at least partially affected by the type of situations and by interpersonal variables such as gender and age; 2. moral reasoning depends in a similar manner on cognitive and affective factors; 3. there is not a gender polarity between the ethic of justice and the ethic of cure/ altruism; 4. moral reasoning and behavior are perceived as reciprocally congruent even though their congruence decreases with a more objective assessment. Such results were discussed in the light of contrasting theories on morality.
Abstract: Artificial Immune System is applied as a Heuristic
Algorithm for decades. Nevertheless, many of these applications
took advantage of the benefit of this algorithm but seldom proposed
approaches for enhancing the efficiency. In this paper, a
Self-evolving Artificial Immune System is proposed via developing
the T and B cell in Immune System and built a self-evolving
mechanism for the complexities of different problems. In this
research, it focuses on enhancing the efficiency of Clonal selection
which is responsible for producing Affinities to resist the invading of
Antigens. T and B cell are the main mechanisms for Clonal
Selection to produce different combinations of Antibodies.
Therefore, the development of T and B cell will influence the
efficiency of Clonal Selection for searching better solution.
Furthermore, for better cooperation of the two cells, a co-evolutional
strategy is applied to coordinate for more effective productions of
Antibodies. This work finally adopts Flow-shop scheduling
instances in OR-library to validate the proposed algorithm.
Abstract: In the age of global communications, heterogeneous
networks are seen to be the best choice of strategy to ensure continuous and uninterruptible services. This will allow mobile
terminal to stay in connection even they are migrating into different segment coverage through the handoff process. With the increase of
teletraffic demands in mobile cellular system, hierarchical cellular systems have been adopted extensively for more efficient channel
utilization and better QoS (Quality of Service). This paper presents a
bidirectional call overflow scheme between two layers of microcells and macrocells, where handoffs are decided by the velocity of mobile
making the call. To ensure that handoff calls are given higher priorities, it is assumed that guard channels are assigned in both
macrocells and microcells. A hysteresis value introduced in mobile velocity is used to allow mobile roam in the same cell if its velocity
changes back within the set threshold values. By doing this the number of handoffs is reduced thereby reducing the processing overhead and enhancing the quality of service to the end user.