Abstract: One of the main issues in Computer Vision is to extract the movement of one or several points or objects of interest in an image or video sequence to conduct any kind of study or control process. Different techniques to solve this problem have been applied in numerous areas such as surveillance systems, analysis of traffic, motion capture, image compression, navigation systems and others, where the specific characteristics of each scenario determine the approximation to the problem. This paper puts forward a Computer Vision based algorithm to analyze fish trajectories in high turbulence conditions in artificial structures called vertical slot fishways, designed to allow the upstream migration of fish through obstructions in rivers. The suggested algorithm calculates the position of the fish at every instant starting from images recorded with a camera and using neural networks to execute fish detection on images. Different laboratory tests have been carried out in a full scale fishway model and with living fishes, allowing the reconstruction of the fish trajectory and the measurement of velocities and accelerations of the fish. These data can provide useful information to design more effective vertical slot fishways.
Abstract: Power Factor (PF) is one of the most important parameters in the electrical systems, especially in the water pumping station. The low power factor value of the water pumping stations causes penalty for the electrical bill. There are many methods use for power factor improvement. Each one of them uses a capacitor on the electrical power network. The position of the capacitors is varied depends on many factors such as; voltage level and capacitors rating. Adding capacitors on the motor terminals increase the supply power factor from 0.8 to more than 0.9 but these capacitors cause some problems for the electrical grid network, such as increasing the harmonic contents of the grid line voltage. In this paper the effects of using capacitors in the water pumping stations to improve the power factor value on the harmonic contents of the electrical grid network are studied. One of large water pumping stations in Kafr El-Shikh Governorate in Egypt was used, as a case study. The effect of capacitors on the line voltage harmonic contents is measured. The station uses capacitors to improve the PF values at the 1 lkv grid network. The power supply harmonics values are measured by a power quality analyzer at different loading conditions. The results showed that; the capacitors improved the power factor value of the feeder and its value increased than 0.9. But the THD values are increased by adding these capacitors. The harmonic analysis showed that; the 13th, 17th, and 19th harmonics orders are increased also by adding the capacitors.
Abstract: The main aim of this study is to describe and introduce a method of numerical analysis in obtaining approximate solutions for the SIR-SI differential equations (susceptible-infectiverecovered for human populations; susceptible-infective for vector populations) that represent a model for dengue disease transmission. Firstly, we describe the ordinary differential equations for the SIR-SI disease transmission models. Then, we introduce the numerical analysis of solutions of this continuous time, discrete space SIR-SI model by simplifying the continuous time scale to a densely populated, discrete time scale. This is followed by the application of this numerical analysis of solutions of the SIR-SI differential equations to the estimation of relative risk using continuous time, discrete space dengue data of Kuala Lumpur, Malaysia. Finally, we present the results of the analysis, comparing and displaying the results in graphs, table and maps. Results of the numerical analysis of solutions that we implemented offers a useful and potentially superior model for estimating relative risks based on continuous time, discrete space data for vector borne infectious diseases specifically for dengue disease.
Abstract: Metropolitan areas have suffered from traffic problems, which have steadily increased in many monocentric cities. Urban expansion, population growth, and road network development have resulted in a structural shift toward urban sprawl, increasing commuters’ dependence on private modes of transport. This paper aims to model the influence of socioeconomic and land-use factors on mode choice using a multinomial and nested logit model. Land-use patterns—such as residential, commercial, retail, educational and employment related—affect the choice of mode and destination in the short and medium term. Socioeconomic factors—such as age, gender, income, household size, and house type—also affect choice, while residential location is affected in the long term. Riyadh in Saudi Arabia and Melbourne in Australia were chosen as case studies. Riyadh is a car-dependent city with limited public transport, whereas Melbourne has good public transport but an increase in car dependence. Aggregate level land-use data and disaggregate level individual, household, and journey-to-work data are used to determine the effects of land use and socioeconomic factors on mode choice. The model results determined that urban sprawl is the main factor that affects mode choice, income, and house type.
Abstract: Fish-feed is a major cost component of operating expenses for any aquaculture farm. Due to soaring prices of fish-feed ingredients, the need for better feeding schedule management has become imperative. On such factor that influences the utilization rate of fish-feed are sea currents. Up to now, practical monitoring of fishfeed loss due to sea currents is not exercised. This paper gives a description of an economic methodology that aims at quantifying the amount of fish-feed lost due to sea currents and draws on data from a Mediterranean aquaculture farm to formulate the associated model.
Abstract: The most influential programming paradigm today
is object oriented (OO) programming and it is widely used in
education and industry. Recognizing the importance of equipping
students with OO knowledge and skills, it is not surprising that most
Computer Science degree programs offer OO-related courses. How
do we assess whether the students have acquired the right objectoriented
skills after they have completed their OO courses? What are
object oriented skills? Currently none of the current assessment
techniques would be able to provide this answer. Traditional forms of
OO programming assessment provide a ways for assigning numerical
scores to determine letter grades. But this rarely reveals information
about how students actually understand OO concept. It appears
reasonable that a better understanding of how to define and assess
OO skills is needed by developing a criterion referenced model. It is
even critical in the context of Malaysia where there is currently a
growing concern over the level of competency of Malaysian IT
graduates in object oriented programming. This paper discussed the
approach used to develop the criterion-referenced assessment model.
The model can serve as a guideline when conducting OO
programming assessment as mentioned. The proposed model is
derived by using Goal Questions Metrics methodology, which helps
formulate the metrics of interest. It concluded with a few suggestions
for further study.
Abstract: This paper presents a new method to detect high impedance faults in radial distribution systems. Magnitudes of third and fifth harmonic components of voltages and currents are used as a feature vector for fault discrimination. The proposed methodology uses a learning vector quantization (LVQ) neural network as a classifier for identifying high impedance arc-type faults. The network learns from the data obtained from simulation of a simple radial system under different fault and system conditions. Compared to a feed-forward neural network, a properly tuned LVQ network gives quicker response.
Abstract: Beginning from the creator of integro-differential
equations Volterra, many scientists have investigated these
equations. Classic method for solving integro-differential
equations is the quadratures method that is successfully applied up
today. Unlike these methods, Makroglou applied hybrid methods
that are modified and generalized in this paper and applied to the
numerical solution of Volterra integro-differential equations. The
way for defining the coefficients of the suggested method is also
given.
Abstract: This study investigated the effect of oxygen and
micro-cracking on the flotation of low grade nickel sulphide ore. The
ore treated contained serpentine minerals which have a history of
being difficult to process efficiently. The use of oxygen as a bubbling
gas has been noted to be effective because it increases the pulp
potential. The desired effect of micro cracking the ore is that the
nickel sulphide minerals will become activated and this activation
will render these minerals more susceptible to react with potassium
amyl xanthate collectors, resulting in a higher recovery of nickel and
hinder the recovery of other undesired minerals contained in the ore.
Higher nickel recoveries were obtained when pure oxygen was used
as a bubbling gas rather than the conventional air. Microwave
cracking favored the recovery of nickel.
Abstract: This paper presents the results related to the
interference reduction technique in multistage multiuser detector for
asynchronous DS-CDMA system. To meet the real-time
requirements for asynchronous multiuser detection, a bit streaming,
cascade architecture is used. An asynchronous multiuser detection
involves block-based computations and matrix inversions. The paper
covers iterative-based suboptimal schemes that have been studied to
decrease the computational complexity, eliminate the need for matrix
inversions, decreases the execution time, reduces the memory
requirements and uses joint estimation and detection process that
gives better performance than the independent parameter estimation
method. The stages of the iteration use cascaded and bits processed
in a streaming fashion. The simulation has been carried out for
asynchronous DS-CDMA system by varying one parameter, i.e.,
number of users. The simulation result exhibits that system gives
optimum bit error rate (BER) at 3rd stage for 15-users.
Abstract: In countries with hot climates, air-conditioning forms
a large proportion of annual peak electrical demand, requiring
expansion of power plants to meet the peak demand, which goes
unused most of the time. Use of well-designed cool storage can offset
the peak demand to a large extent. In this study, an air conditioning
system with naturally stratified storage tank was designed,
constructed and tested. A new type of diffuser was designed and used
in this study. Factors that influence the performance of chilled water
storage tanks were investigated. The results indicated that stratified
storage tank consistently stratified well without any physical barrier.
Investigation also showed that storage efficiency decreased with
increasing flow rate due to increased mixing of warm and chilled
water. Diffuser design and layout primarily affected the mixing near
the inlet diffuser and the extent of this mixing had primary influence
on the shape of the thermocline. The heat conduction through tank
walls and through the thermocline caused widening of mixed volume.
Thermal efficiency of stratified storage tanks was as high as 90
percent, which indicates that stratified tanks can effectively be used
as a load management technique.
Abstract: The bag radius of the nucleon can be determined by MIT bag model based on electric and magnetic form factors of the nucleon. Also we determined the masses and magnetic moment of the nucleon with MIT bag model, using bag radius and compared with other results, suggests a suitable compatibility.
Abstract: The purpose of this paper is to discuss the influence of
resistance characteristic on the high conductive concrete considering
the various voltage and environment. The four-electrode method is
applied to the tailor-made high conductive concrete with appropriate
proportion. The curve of resistivity with the changes of voltage and
environment is plotted and the changes of resistivity are explored. The
result based on the methods reveals that resistivity is less affected by
the temperature factor, and the four-electrode method would be an
applicable measurement method on a site inspection.
Abstract: This study used Item Analysis, Exploratory Factor
Analysis (EFA) and Reliability Analysis (Cronbach-s α value) to
exam the Questions which selected by the Delphi method based on the
issue of “Socio-technical system (STS)" and user-centered
perspective. A structure questionnaire with seventy-four questions
which could be categorized into nine dimensions (healthcare
environment, organization behaviour, system quality, medical data
quality, service quality, safety quality, user usage, user satisfaction,
and organization net benefits) was provided to evaluate EMR of the
Taiwanese healthcare environment.
Abstract: In this paper we propose a Particle Swarm heuristic
optimized Multi-Antenna (MA) system. Efficient MA systems
detection is performed using a robust stochastic evolutionary
computation algorithm based on movement and intelligence of
swarms. This iterative particle swarm optimized (PSO) detector
significantly reduces the computational complexity of conventional
Maximum Likelihood (ML) detection technique. The simulation
results achieved with this proposed MA-PSO detection algorithm
show near optimal performance when compared with ML-MA
receiver. The performance of proposed detector is convincingly
better for higher order modulation schemes and large number of
antennas where conventional ML detector becomes non-practical.
Abstract: This research study aims to identify the impact of two
factors –growth and competitive strategies- on a set of building
production innovation strategies. It was conducted a questionery
survey to collect data from construction professionals and it was
asked them the importance level of predicted innovation strategies for
corporate strategies. Multiple analysis of variance (MANOVA) was
employed to see the main and interaction effects of corporate
strategies on building innovation strategies. The results indicate that
growth strategies such as entering in a new a market or new project
types has a greater effect on innovation strategies rather than
competitive strategies such as cost leadership or differentiation
strategies. However the interaction effect of competitive strategies
and growth strategies on innovation strategies is much bigger than
the only effect of competitive strategies. It was also analyzed the
descriptive statistics of innovation strategies for different competitive
and growth strategy types.
Abstract: The objective of this study is to determine the thermal comfort among worker at Malaysian automotive industry. One critical manual assembly workstation had been chosen as a subject for the study. The human subjects for the study constitute operators at Body Assembly Station of the factory. The environment examined was the Relative Humidity (%), Airflow (m/s), Air Temperature (°C) and Radiant Temperature (°C) of the surrounding workstation area. The environmental factors were measured using Babuc apparatus, which is capable to measure simultaneously those mentioned environmental factors. The time series data of fluctuating level of factors were plotted to identify the significant changes of factors. Then thermal comfort of the workers were assessed by using ISO Standard 7730 Thermal sensation scale by using Predicted Mean Vote (PMV). Further Predicted percentage dissatisfied (PPD) is used to estimate the thermal comfort satisfaction of the occupant. Finally the PPD versus PMV were plotted to present the thermal comfort scenario of workers involved in related workstation. The result of PMV at the related industry is between 1.8 and 2.3, where PPD at that building is between 60% to 84%. The survey result indicated that the temperature more influenced comfort to the occupants
Abstract: In this study we focus on improvement performance
of a cue based Motor Imagery Brain Computer Interface (BCI). For
this purpose, data fusion approach is used on results of different
classifiers to make the best decision. At first step Distinction
Sensitive Learning Vector Quantization method is used as a feature
selection method to determine most informative frequencies in
recorded signals and its performance is evaluated by frequency
search method. Then informative features are extracted by packet
wavelet transform. In next step 5 different types of classification
methods are applied. The methodologies are tested on BCI
Competition II dataset III, the best obtained accuracy is 85% and the
best kappa value is 0.8. At final step ordered weighted averaging
(OWA) method is used to provide a proper aggregation classifiers
outputs. Using OWA enhanced system accuracy to 95% and kappa
value to 0.9. Applying OWA just uses 50 milliseconds for
performing calculation.
Abstract: Sugarcane bagasses are one of the most extensively used agricultural residues. Using acid hydrolysis and fermentation, conversion of sugarcane bagasses to lactic acid was technically and economically feasible. This research was concerned with the solubility of lignin in ammonium hydroxide, acid hydrolysis and lactic acid fermentation by Lactococcus lactis, Lactobacillus delbrueckii, Lactobacillus plantarum, and Lactobacillus casei. The lignin extraction results for different ammonium hydroxide concentrations showed that 10 % (v/v) NH4OH was favorable to lignin dissolution. Acid hydrolysis can be enhanced with increasing acid concentration and reaction temperature. The optimum glucose and xylose concentrations occurred at 121 ○C for 1 hour hydrolysis time in 10% sulphuric acid solution were 32 and 11 g/l, respectively. In order to investigate the significance of medium composition on lactic acid production, experiments were undertaken whereby a culture of Lactococcus lactis was grown under various glucose, peptone, yeast extract and xylose concentrations. The optimum medium was composed of 5 g/l glucose, 2.5 g/l xylose, 10 g/l peptone and 5 g/l yeast extract. Lactococcus lactis represents the most efficient for lactic acid production amongst those considered. The lactic acid fermentation by Lactococcus lactis after 72 hours gave the highest yield of 1.4 (g lactic acid per g reducing sugar).
Abstract: The overall objective of this paper is to retrieve soil
surfaces parameters namely, roughness and soil moisture related to
the dielectric constant by inverting the radar backscattered signal
from natural soil surfaces.
Because the classical description of roughness using statistical
parameters like the correlation length doesn't lead to satisfactory
results to predict radar backscattering, we used a multi-scale
roughness description using the wavelet transform and the Mallat
algorithm. In this description, the surface is considered as a
superposition of a finite number of one-dimensional Gaussian
processes each having a spatial scale. A second step in this study
consisted in adapting a direct model simulating radar backscattering
namely the small perturbation model to this multi-scale surface
description. We investigated the impact of this description on radar
backscattering through a sensitivity analysis of backscattering
coefficient to the multi-scale roughness parameters.
To perform the inversion of the small perturbation multi-scale
scattering model (MLS SPM) we used a multi-layer neural network
architecture trained by backpropagation learning rule. The inversion
leads to satisfactory results with a relative uncertainty of 8%.