Abstract: Modeling and simulation of fixed bed three-phase
catalytic reactors are considered for wet air catalytic oxidation of
phenol to perform a comparative numerical analysis between tricklebed
and packed-bubble column reactors. The modeling involves
material balances both for the catalyst particle as well as for different
fluid phases. Catalyst deactivation is also considered in a transient
reactor model to investigate the effects of various parameters
including reactor temperature on catalyst deactivation. The
simulation results indicated that packed-bubble columns were
slightly superior in performance than trickle beds. It was also found
that reaction temperature was the most effective parameter in catalyst
deactivation.
Abstract: In seismic survey, the information regarding the
velocity of compression wave (Vp) as well as shear wave (Vs) are
very useful especially during the seismic interpretation. Previous
studies showed that both Vp and Vs determined by above methods
are totally different with respect to each other but offered good
approximation. In this study, both Vp and Vs of consolidated granite
rock were studied by using ultrasonic testing method and seismic
refraction method. In ultrasonic testing, two different condition of
rock are used which is dry and wet. The differences between Vp and
Vs getting by using ultrasonic testing and seismic refraction were
investigated and studied. The effect of water content in granite rock
towards the value of Vp and Vs during ultrasonic testing are also
measured. Within this work, the tolerance of the differences between
the velocity of seismic wave getting from ultrasonic testing and the
velocity of seismic wave getting from seismic refraction are also
measured and investigated.
Abstract: Considering non-ideal behavior of fluids and its effects on hydrodynamic and mass transfer in multiphase flow is very essential. Simulations were performed that takes into account the effects of mass transfer and mixture non-ideality on hydrodynamics reported by Irani et al. In this paper, by assuming the density of phases to be constant and Raullt-s law instead of using EOS and fugacity coefficient definition, respectively for both the liquid and gas phases, the importance of non-ideality effects on mass transfer and hydrodynamic behavior was studied. The results for a system of octane/propane (T=323 K, P =445 kpa) also indicated that the assumption of constant density in simulation had major role to diverse from experimental data. Furthermore, comparison between obtained results and the previous report indicated significant differences between experimental data and simulation results with more ideal assumptions.
Abstract: With the exponential progress of technological
development comes a strong sense that events are moving too quickly
for our schools and that teachers may be losing control of them in the
process. This paper examines the impact of e-learning and e-teaching
in universities, from both the student and teacher perspective. In
particular, it is shown that e-teachers should focus not only on the
technical capacities and functions of IT materials and activities, but
must attempt to more fully understand how their e-learners perceive
the learning environment. From the e-learner perspective, this paper
indicates that simply having IT tools available does not automatically
translate into all students becoming effective learners. More
evidence-based evaluative research is needed to allow e-learning and
e-teaching to reach full potential.
Abstract: The recent development of humanoid robots has led robot designers to imagine a great variety of anthropomorphic forms for human-like machine. Which form is the best ? We try to answer this question from a double meaning of the anthropomorphism : a positive anthropomorphism corresponing to the realization of an effective anthropomorphic form object and a negative one corresponding to our natural tendency in certain circumstances to give human attributes to non-human beings. We postulate that any humanoid robot is concerned by both these two anthropomorphism kinds. We propose to use gestalt theory and Heider-s balance theory in order to analyze how negative anthropomorphism can influence our perception of human-like robots. From our theoretical approach we conclude that an “even shape" as defined by gestalt theory is not a sufficient condition for a good integration of future humanoid robots into a human community. Aesthetic perception of the robot cannot be splitted from a social perception : a humanoid robot, any how the efforts made for improving its appearance, could be rejected if it is devoted to a task with too high affective implications.
Abstract: The purpose of this study was to develop and examine a
Teaching Commitment Scale of Health and Physical Education
(TCS-HPE) for Taiwanese elementary school teachers. First of all,
based on teaching commitment related theory and literatures to
develop a original scale with 40 items, later both stratified random
sampling and cluster sampling were used to sample participants.
During the first stage, 300 teachers were sampled and 251 valid scales
(83.7%) returned. Later, the data was analyzed by exploratory factor
analysis to obtain 74.30% of total variance for the construct validity.
The Cronbach-s alpha coefficient of sum scale reliability was 0.94, and
subscale coefficients were between 0.80 and 0.96. In the second stage,
400 teachers were sampled and 318 valid scales (79.5%) returned.
Finally, this study used confirmatory factor analysis to test validity and
reliability of TCS-HPE. The result showed that the fit indexes reached
acceptable criteria(¤ç2
(246 ) =557.64 , p
Abstract: Repetitive systems stand for a kind of systems that
perform a simple task on a fixed pattern repetitively, which are
widely spread in industrial fields. Hence, many researchers have been
interested in those systems, especially in the field of iterative learning
control (ILC). In this paper, we propose a finite-horizon tracking
control scheme for linear time-varying repetitive systems with uncertain
initial conditions. The scheme is derived both analytically
and numerically for state-feedback systems and only numerically for
output-feedback systems. Then, it is extended to stable systems with
input constraints. All numerical schemes are developed in the forms
of linear matrix inequalities (LMIs). A distinguished feature of the
proposed scheme from the existing iterative learning control is that
the scheme guarantees the tracking performance exactly even under
uncertain initial conditions. The simulation results demonstrate the
good performance of the proposed scheme.
Abstract: Two short sediment cores collected from mangrove
areas of Manori and Thane creeks along Mumbai coast were analysed
for sediment composition and metals (Fe, Mn, Cu, Pb, Co, Ni, Zn, Cr
and V). The statistical analysis of Pearson correlation matrix proved
that there is a significant relationship between metal concentration
and finer grain size in Manori creek while poor correlation was
observed in Thane creek. Based on the enrichment factor, the present
metal to background metal ratios clearly reflected maximum
enrichment of Cu and Pb in Manori creek and Mn in Thane creek.
Geoaccumulation index calculated indicate that the study area is
unpolluted with respect to Fe, Mn, Co, Ni, Zn and Cr in both the
cores while moderately polluted with Cu and Pb in Manori creek.
Based on contamination degree, both the core sediments were found
to be considerably contaminated with metals.
Abstract: In this work, the natural convection in a concentric
annulus between a cold outer inclined square enclosure and heated
inner circular cylinder is simulated for two-dimensional steady
state. The Boussinesq approximation was applied to model the
buoyancy-driven effect and the governing equations were solved
using the time marching approach staggered by body fitted
coordinates. The coordinate transformation from the physical
domain to the computational domain is set up by an analytical
expression. Numerical results for Rayleigh numbers 103 , 104 , 105
and 106, aspect ratios 1.5 , 3.0 and 4.5 for seven different
inclination angles for the outer square enclosure 0o , -30o
, -45o
,
-60o , -90o , -135o , -180o are presented as well. The computed flow
and temperature fields were demonstrated in the form of
streamlines, isotherms and Nusselt numbers variation. It is found
that both the aspect ratio and the Rayleigh number are critical to the
patterns of flow and thermal fields. At all Rayleigh numbers angle
of inclination has nominal effect on heat transfer.
Abstract: In the present work flow past circular cylinder and
cylinder with rectangular and triangular wake splitter is studied to
improve aerodynamic parameters. The Comparison of drag
coefficient is tabulated for bare cylinder, cylinder with rectangular
and triangular wake splitters. Flow past circular cylinder and cylinder
with triangular and rectangular wake splitter is performed at
Reynoldsnumber 5, 20, 40, 50,80, 100.An incompressible PISO finite
volume code employing a non-staggered grid arrangement is used, a
second order upwind scheme is used for convective terms. The time
discretization is implicit and a Second order Crank-Nicholson scheme
is employed. Length of wake splitter in both configurations is taken
to be equal to diameter of cylinder. Wake length is found to be less
with rectangular wake splitter when compared to bare cylinder and
cylinder with triangular wake splitter. Coefficient of drag is found to
be less for triangular wake splitter when compared to bare cylinder &
cylinder with rectangular wake splitter.
Abstract: The world demand for potable water is
increasing every day with growing population. Desalination
using solar energy is suitable for potable water production
from brackish and seawater. In this paper, we present a
theoretical study of solar distillation in a single basin under
the open environmental conditions of Chabahar-Iran. The still
has a base area of 2000mm×500mm with a glass cover
inclined at 25° in order to obtain extra solar energy. We model
the still and conduct its energy balance equations under minor
assumptions. We computed the temperatures of glass cover,
seawater interface, moist air and bottom using numerical
method. The investigation addressed the following: The still
productivity, distilled water salinity and still performance in
terms of the still efficiency. Calculated still productivity in
July was higher than December. So in this paper, we show
that still productivity is directly functioning of solar radiation.
Abstract: In today-s turbulent environment, companies are faced with two principal challenges. On the one hand, it is necessary to produce ever more cost-effectively to remain competitive. On the other hand, factories need to be transformable in order to manage unpredictable changes in the corporate environment. To deal with these different challenges, companies use the philosophy of lean production in the first case, in the second case the philosophy of transformability. To a certain extent these two approaches follow different directions. This can cause conflicts when designing factories. Therefore, the Institute of Production Systems and Logistics (IFA) of the Leibniz University of Hanover has developed a procedure to allow companies to evaluate and design their factories with respect to the requirements of both philosophies.
Abstract: In this paper a neural adaptive control method has
been developed and applied to robot control. Simulation results are
presented to verify the effectiveness of the controller. These results
show that the performance by using this controller is better than
those which just use either direct inverse control or predictive
control. In addition, they show that the resulting is a useful method
which combines the advantages of both direct inverse control and
predictive control.
Abstract: This paper presents an algorithm for the recognition
and tracking of moving objects, 1/10 scale model car is used to verify
performance of the algorithm. Presented algorithm for the recognition
and tracking of moving objects in the paper is as follows. SURF
algorithm is merged with Lucas-Kanade algorithm. SURF algorithm
has strong performance on contrast, size, rotation changes and it
recognizes objects but it is slow due to many computational
complexities. Processing speed of Lucas-Kanade algorithm is fast but
the recognition of objects is impossible. Its optical flow compares the
previous and current frames so that can track the movement of a pixel.
The fusion algorithm is created in order to solve problems which
occurred using the Kalman Filter to estimate the position and the
accumulated error compensation algorithm was implemented. Kalman
filter is used to create presented algorithm to complement problems
that is occurred when fusion two algorithms. Kalman filter is used to
estimate next location, compensate for the accumulated error. The
resolution of the camera (Vision Sensor) is fixed to be 640x480. To
verify the performance of the fusion algorithm, test is compared to
SURF algorithm under three situations, driving straight, curve, and
recognizing cars behind the obstacles. Situation similar to the actual is
possible using a model vehicle. Proposed fusion algorithm showed
superior performance and accuracy than the existing object
recognition and tracking algorithms. We will improve the performance
of the algorithm, so that you can experiment with the images of the
actual road environment.
Abstract: The hand is one of the essential parts of the body for
carrying out Activities of Daily Living (ADLs). Individuals use their
hands and fingers in everyday activities in the both the workplace
and home. Hand-intensive tasks require diverse and sometimes
extreme levels of exertion, depending on the action, movement or
manipulation involved. The authors have undertaken several studies
looking at grip choice and comfort. It is hoped that in providing
improved understanding of discomfort during ADLs this will aid in
the design of consumer products.
Previous work by the authors outlined a methodology for
calculating pain frequency and pain level for a range of tasks. From
an online survey undertaken by the authors with regards
manipulating objects during everyday tasks, tasks involving
gripping were seen to produce the highest levels of pain and
discomfort. Questioning of the participants showed that cleaning
tasks were seen to be ADL's that produced the highest levels of
discomfort, with women feeling higher levels of discomfort than
men.
This paper looks at the methodology for calculating pain
frequency and pain level with particular regards to gripping
activities. This methodology shows that activities such as mopping,
sweeping and hoovering shows the highest numbers of pain
frequency and pain level at 3112.5 frequency per month while the
pain level per person doing this action was 0.78.The study then uses
thin-film force sensors to analyze the force distribution in the hand
whilst hoovering and compares this for differing grip styles and
genders. Women were seen to have more of their hand under a
higher pressure than men when undertaking hoovering. This
suggests that women may feel greater discomfort than men since
their hand is at a higher pressure more of the time.
Abstract: The most important parameter in transformers life
expectancy is the hot-spot temperature level which accelerates the
rate of aging of the insulation. The aim of this paper is to present
thermal models for transformers loaded at prefabricated MV/LV
transformer substations and outdoor situations. The hot-spot
temperature of transformers is studied using their top-oil temperature
rise models. The thermal models proposed for hot-spot and top-oil
temperatures of different operating situations are compared. Since the
thermal transfer is different for indoor and outdoor transformers
considering their operating conditions, their hot-spot thermal models
differ from each other. The proposed thermal models are verified by
the results obtained from the experiments carried out on a typical
1600 kVA, 30 /0.4 kV, ONAN transformer for both indoor and
outdoor situations.
Abstract: Computers are being integrated in the various aspects
of human every day life in different shapes and abilities. This fact
has intensified a requirement for the software development
technologies which is ability to be: 1) portable, 2) adaptable, and 3)
simple to develop. This problem is also known as the Pervasive
Computing Problem (PCP) which can be implemented in different
ways, each has its own pros and cons and Context Oriented
Programming (COP) is one of the methods to address the PCP.
In this paper a design for a COP framework, a context aware
framework, is presented which has eliminated weak points of a
previous design based on interpreter languages, while introducing the
compiler languages power in implementing these frameworks.
The key point of this improvement is combining COP and
Dependency Injection (DI) techniques. Both old and new frameworks
are analyzed to show advantages and disadvantages. Finally a
simulation of both designs is proposed to indicating that the practical
results agree with the theoretical analysis while the new design runs
almost 8 times faster.
Abstract: This paper describes a system-level SoC energy
consumption estimation method based on a dynamic behavior of
embedded software in the early stages of the SoC development. A
major problem of SOC development is development rework caused by
unreliable energy consumption estimation at the early stages. The
energy consumption of an SoC used in embedded systems is strongly
affected by the dynamic behavior of the software. At the early stages
of SoC development, modeling with a high level of abstraction is
required for both the dynamic behavior of the software, and the
behavior of the SoC. We estimate the energy consumption by a UML
model-based simulation. The proposed method is applied for an actual
embedded system in an MFP. The energy consumption estimation of
the SoC is more accurate than conventional methods and this proposed
method is promising to reduce the chance of development rework in
the SoC development. ∈
Abstract: Since the world printing industry has to confront
globalization with a constant change, the Thai printing industry, as a
small but increasingly significant part of the world printing industry,
cannot inevitably escape but has to encounter with the similar change
and also the need to revamp its production processes, designs and
technology to make them more appealing to both international and
domestic market. The essential question is what is the Thai
competitive edge in the printing industry in changing environment?
This research is aimed to study the Thai level of competitive edge in
terms of marketing, technology, environment friendly, and the level
of satisfaction of the process of using printing machines. To access
the extent to which is the trends in competitiveness of Thai printing
industry, both quantitative and qualitative study were conducted. The
quantitative analysis was restricted to 100 respondents. The
qualitative analysis was restricted to a focus group of 10 individuals
from various backgrounds in the Thai printing industry. The findings
from the quantitative analysis revealed that the overall mean scores
are 4.53, 4.10, and 3.50 for the competitiveness of marketing, the
competitiveness of technology, and the competitiveness of being
environment friendly respectively. However, the level of satisfaction
for the process of using machines has a mean score only 3.20. The
findings from the qualitative analysis have revealed that target
customers have increasingly reordered due to their contentment in
both low prices and the acceptable quality of the products. Moreover,
the Thai printing industry has a tendency to convert to ambient green
technology which is friendly to the environment. The Thai printing
industry is choosing to produce or substitute with products that are
less damaging to the environment. It is also found that the Thai
printing industry has been transformed into a very competitive
industry which bargaining power rests on consumers who have a
variety of choices.
Abstract: A four-lobe pressure dam bearing which is
produced by cutting two pressure dams on the upper two lobes and
two relief-tracks on the lower two lobes of an ordinary four-lobe
bearing is found to be more stable than a conventional four-lobe
bearing. In this paper a four-lobe pressure dam bearing supporting
rigid and flexible rotors is analytically investigated to determine its
performance when L/D ratio is varied in the range 0.75 to 1.5. The
static and dynamic characteristics are studied at various L/D ratios.
The results show that the stability of a four-lobe pressure dam
bearing increases with decrease in L/D ratios both for rigid as well as
flexible rotors.