Abstract: At present, it is very common to find renewable
energy resources, especially wind power, connected to distribution
systems. The impact of this wind power on voltage distribution levels
has been addressed in the literature. The majority of this works deals
with the determination of the maximum active and reactive power
that is possible to be connected on a system load bus, until the
voltage at that bus reaches the voltage collapse point. It is done by the
traditional methods of PV curves reported in many references.
Theoretical expression of maximum power limited by voltage
stability transfer through a grid is formulated using an exact
representation of distribution line with ABCD parameters. The
expression is used to plot PV curves at various power factors of a
radial system. Limited values of reactive power can be obtained. This
paper presents a method to study the relationship between the active
power and voltage (PV) at the load bus to identify the voltage
stability limit. It is a foundation to build a permitted working
operation region in complying with the voltage stability limit at the
point of common coupling (PCC) connected wind farm.
Abstract: Design and implementation of a novel B-ACOSD CFAR algorithm is presented in this paper. It is proposed for detecting radar target in log-normal distribution environment. The BACOSD detector is capable to detect automatically the number interference target in the reference cells and detect the real target by an adaptive threshold. The detector is implemented as a System on Chip on FPGA Altera Stratix II using parallelism and pipelining technique. For a reference window of length 16 cells, the experimental results showed that the processor works properly with a processing speed up to 115.13MHz and processing time0.29 ┬Ás, thus meets real-time requirement for a typical radar system.
Abstract: This paper describes Nano-particle based Planar Laser
Scattering (NPLS) flow visualization of angled supersonic jets into a
supersonic cross flow based on the HYpersonic Low TEmperature
(HYLTE) nozzle which was widely used in DF chemical laser. In
order to investigate the non-reacting flowfield in the HYLTE nozzle, a
testing section with windows was designed and manufactured. The
impact of secondary fluids orifice separation on mixing was examined.
For narrow separation of orifices, the secondary fuel penetration
increased obviously compared to diluent injection, which means
smaller separation of diluent and fuel orifices would enhance the
mixing of fuel and oxidant. Secondary injections with angles of 30, 40
and 50 degrees were studied. It was found that the injectant
penetration increased as the injection angle increased, while the
interfacial surface area to entrain the freestream fluid is largest when
the injection angle is 40 degree.
Abstract: In this paper, Wavelet based ANFIS for finding inter
turn fault of generator is proposed. The detector uniquely responds to
the winding inter turn fault with remarkably high sensitivity.
Discrimination of different percentage of winding affected by inter
turn fault is provided via ANFIS having an Eight dimensional input
vector. This input vector is obtained from features extracted from
DWT of inter turn faulty current leaving the generator phase
winding. Training data for ANFIS are generated via a simulation of
generator with inter turn fault using MATLAB. The proposed
algorithm using ANFIS is giving satisfied performance than ANN
with selected statistical data of decomposed levels of faulty current.
Abstract: This paper presents a method for obtaining the
desired reference current for Voltage Source Converter (VSC) of the Shunt Active Power Filter (SAPF) using Synchronous Reference Frame Theory. The method relies on the performance of the Proportional-Integral (PI) controller for
obtaining the best control performance of the SAPF. To
improve the performance of the PI controller, the feedback
path to the integral term is introduced to compensate the
winding up phenomenon due to integrator. Using Reference
Frame Transformation, reference signals are transformed from
a - b - c stationery frame to 0 - d - q rotating frame.
Using the PI controller, the reference signals in the 0 - d - q rotating frame are controlled to get the desired reference signals for the Pulse Width Modulation. The synchronizer, the Phase Locked Loop (PLL) with PI filter is used for
synchronization, with much emphasis on minimizing delays. The system performance is examined with Shunt Active Power Filter simulation model.
Abstract: Higher capacities of power plants together with
increased awareness on environmental considerations have led to
taller height of stacks. It is seen that strong wind can result in falling
of stacks. So, aerodynamic consideration of stacks is very important
in order to save the falling of stacks. One stack is not enough in
industries and power sectors and two or three stacks are required for
proper operation of the unit. It is very important to arrange the stacks
in proper way to resist their downfall. The present experimental
study concentrates on the mutual effect of three nearby stacks on
each other at three different arrangements, viz. linear, side-by-side
and triangular. The experiments find out the directions of resultant
forces acting on the stacks in different configurations so that proper
arrangement of supports can be made with respect to the wind
directionality obtained from local meteorological data. One can also
easily ascertain which stack is more vulnerable to wind in
comparison to the others for a particular configuration. Thus, this
study is important in studying the effect of wind force on three stacks
in different arrangements and is very helpful in placing the supports
in proper places in order to avoid failing of stack-like structures due
to wind.
Abstract: This work presents a comparison between the Annual
Energy Output (AEO) of two commercial vertical-axis wind turbines
(VAWTs) for a low-wind urban site: both a drag-driven and a liftdriven
concepts are examined in order to be installed on top of the
new Via dei Giustinelli building, Trieste (Italy). The power-curves,
taken from the product specification sheets, have been matched to the
wind characteristics of the selected installation site. The influence of
rotor swept area and rated power on the performance of the two
proposed wind turbines have been examined in detail, achieving a
correlation between rotor swept area, electrical generator size and
wind distribution, to be used as a guideline for the calculation of the
AEO.
Abstract: Subsonic wind tunnel experiments were conducted to
study the effect of tripped boundary layer on the pressure distribution
in the contraction region of the tunnel. Measurements were
performed by installing trip strip at two different positions in the
concave portion of the contraction. The results show that installation
of the trip strips, have significant effects on both turbulence and
pressure distribution. The reduction in the free stream turbulence and
reduction of the wall static pressure distribution deferred signified
with the location of the trip strip.
Abstract: BEAMnrc was used to calculate the spectrum and
HVL for X-ray Beam during low energy X-ray radiation using tube model: SRO 33/100 /ROT 350 Philips. The results of BEAMnrc
simulation and measurements were compared to the IPEM report
number 78 and SpekCalc software. Three energies 127, 103 and 84
Kv were used. In these simulation a tungsten anode with 1.2 mm for
Be window were used as source. HVLs were calculated from
BEAMnrc spectrum with air Kerma method for four different filters.
For BEAMnrc one billion particles were used as original particles for
all simulations. The results show that for 127 kV, there was
maximum 5.2 % difference between BEAMnrc and Measurements
and minimum was 0.7% .the maximum 9.1% difference between
BEAMnrc and IPEM and minimum was 2.3% .The maximum
difference was 3.2% between BEAMnrc and SpekCal and minimum
was 2.8%. The result show BEAMnrc was able to satisfactory predict
the quantities of Low energy Beam as well as high energy X-ray
radiation.
Abstract: So much energy is used in high rise buildings to fulfill
the basic needs of users such as lighting and thermal comfort.
Malaysia has hot and humid climate, buildings especially high rise
buildings receive unnecessary solar radiation that cause more solar
heat gain. Energy use specially electricity consumption in high rise
buildings has increased. There have been growing concerns about
energy consumption and its effect on environment. Building, energy
and the environment are important issues that the designers should
consider to them. Self protected form is one of possible ways against
the impact of solar radiation in high rise buildings. The Energy
performance of building envelopes was investigated in term of the
Overall Thermal Transfer Value (OTTV ).In this paper, the amount
of OTTV reduction was calculated through OTTV Equations to
clear the effectiveness of self shading strategy on minimizing energy
consumption for cooling interior spaces in high rise buildings which
has considerable envelope areas against solar radiation. Also increasing
the optimum window area was investigated using self-shading
strategy in designing high rise buildings. As result, the significant
reduction in OTTV was shown based on WWR.In addition slight
increase was demonstrated in WWR that can influence on visible
comfort interior spaces.
Abstract: Most fingerprint recognition techniques are based on minutiae matching and have been well studied. However, this technology still suffers from problems associated with the handling of poor quality impressions. One problem besetting fingerprint matching is distortion. Distortion changes both geometric position and orientation, and leads to difficulties in establishing a match among multiple impressions acquired from the same finger tip. Marking all the minutiae accurately as well as rejecting false minutiae is another issue still under research. Our work has combined many methods to build a minutia extractor and a minutia matcher. The combination of multiple methods comes from a wide investigation into research papers. Also some novel changes like segmentation using Morphological operations, improved thinning, false minutiae removal methods, minutia marking with special considering the triple branch counting, minutia unification by decomposing a branch into three terminations, and matching in the unified x-y coordinate system after a two-step transformation are used in the work.
Abstract: Control of commutation of switched reluctance (SR)
motor has been an area of interest for researchers for sometime now
with mixed successes in addressing the inherent challenges. New
technologies, processing schemes and methods have been adopted to
make sensorless SR drive a reality. There are a number of
conceptual, offline, analytical and online solutions in literature that
have varying complexities and achieved equally varying degree of
robustness and accuracies depending on the method used to address
the challenges and the SR drive application. Magnetic coupling is
one such challenge when using active probing techniques to
determine rotor position of a SR motor from stator winding. This
paper studies the effect of back-of-core saturation on the detected
rotor position and presents results on measurement made on a 4-
phase SR motor. The results shows that even for a four phase motor
which is excited one phase at a time and using the electrically
opposite phase for active position probing, the back-of-core
saturation effects should not be ignored.
Abstract: In field of Computer Science and Mathematics,
sorting algorithm is an algorithm that puts elements of a list in a
certain order i.e. ascending or descending. Sorting is perhaps the
most widely studied problem in computer science and is frequently
used as a benchmark of a system-s performance. This paper
presented the comparative performance study of four sorting
algorithms on different platform. For each machine, it is found that
the algorithm depends upon the number of elements to be sorted. In
addition, as expected, results show that the relative performance of
the algorithms differed on the various machines. So, algorithm
performance is dependent on data size and there exists impact of
hardware also.
Abstract: The objective this study was to characterize and
develop anthropomorphic liver phantoms in tomography hepatic
procedures for quality control and improvement professionals in
nuclear medicine. For the conformation of the anthropomorphic
phantom was used in plaster and acrylic. We constructed three
phantoms representing processes with liver cirrhosis. The phantoms
were filled with 99mTc diluted with water to obtain the scintigraphic
images. Tomography images were analyzed anterior and posterior
phantom representing a body with a greater degree cirrhotic. It was
noted that the phantoms allow the acquisition of images similar to
real liver with cirrhosis. Simulations of hemangiomas may contribute
to continued professional education of nuclear medicine, on the
question of image acquisition, allowing of the study parameters such
of the matrix, energy window and count statistics.
Abstract: In this paper, a design methodology to implement low-power and high-speed 2nd order recursive digital Infinite Impulse Response (IIR) filter has been proposed. Since IIR filters suffer from a large number of constant multiplications, the proposed method replaces the constant multiplications by using addition/subtraction and shift operations. The proposed new 6T adder cell is used as the Carry-Save Adder (CSA) to implement addition/subtraction operations in the design of recursive section IIR filter to reduce the propagation delay. Furthermore, high-level algorithms designed for the optimization of the number of CSA blocks are used to reduce the complexity of the IIR filter. The DSCH3 tool is used to generate the schematic of the proposed 6T CSA based shift-adds architecture design and it is analyzed by using Microwind CAD tool to synthesize low-complexity and high-speed IIR filters. The proposed design outperforms in terms of power, propagation delay, area and throughput when compared with MUX-12T, MCIT-7T based CSA adder filter design. It is observed from the experimental results that the proposed 6T based design method can find better IIR filter designs in terms of power and delay than those obtained by using efficient general multipliers.
Abstract: The 'wind-rain' house has a courtyard with glazed
roof, which allows more direct sunlight to come into indoor spaces
during the winter. The glazed roof can be partially opened or closed
and automatically controlled to provide natural ventilation in order to
adjust for indoor thermal conditions and the roof area can be shaded
by reflective insulation materials during the summer. Two field
studies for evaluating indoor thermal conditions of the two 'windrain'
houses have been carried out by author in 2009 and 2010.
Indoor and outdoor air temperature and relative humidity adjacent to
floor and ceiling of the two sample houses were continuously tested
at 15-minute intervals, 24 hours a day during the winter months.
Based on field study data, this study investigates relationships
between building design and indoor thermal condition of the 'windrain'
house to improve the future house design for building thermal
comfort and energy efficiency
Abstract: Masonry cavity walls are loaded by wind pressure and vertical load from upper floors. These loads results in bending moments and compression forces in the ties connecting the outer and the inner wall in a cavity wall. Large cavity walls are furthermore loaded by differential movements from the temperature gradient between the outer and the inner wall, which results in critical increase of the bending moments in the ties. Since the ties are loaded by combined compression and moment forces, the loadbearing capacity is derived from instability equilibrium equations. Most of them are iterative, since exact instability solutions are complex to derive, not to mention the extra complexity introducing dimensional instability from the temperature gradients. Using an inverse variable substitution and comparing an exact theory with an analytical instability solution a method to design tie-connectors in cavity walls was developed. The method takes into account constraint conditions limiting the free length of the wall tie, and the instability in case of pure compression which gives an optimal load bearing capacity. The model is illustrated with examples from praxis.
Abstract: Both prognostic and diagnostic modes of a 3D baroclinic
model in hydrodynamic and sediment transport models of
the Princeton Ocean Model (POM) were conducted to separate
prognose and diagnose effects of different hydrodynamic factors on
transport of suspended sediment discharged from the rivers to the
Gulf of Thailand (GoT). Both transport modes of suspended sediment
distribution in the GoT were numerically simulated. It could be
concluded that the suspended sediment discharged from the rivers
around the GoT. Most of sediments in estuaries and coastal areas are
deposited outside the GoT under the condition of wind-driven current,
and very small amount of the sediments of them are transported
faraway. On the basis of wind forcing, sediments from the lower
GoT to the upper GoT are mainly transported south-northwestward
and also continuously moved north-southwestward. An obvious 3D
characteristic of suspended sediment transport is produced in the
wind-driven current residual circulation condition. In this study, the
transport patterns at the third layer are generally consistent with
the typhoon-induced strong currents in two case studies of Typhoon
Linda 1997. The case studies presented the prognostic and diagnostic
modes during 00UTC28OCT1997 to 12UTC06NOV1997 in a short
period with the current condition for pre-operation of the suspended
sediment transport model in estuaries and coastal areas.
Abstract: A clustering is process to identify a homogeneous
groups of object called as cluster. Clustering is one interesting topic
on data mining. A group or class behaves similarly characteristics.
This paper discusses a robust clustering process for data images with
two reduction dimension approaches; i.e. the two dimensional
principal component analysis (2DPCA) and principal component
analysis (PCA). A standard approach to overcome this problem is
dimension reduction, which transforms a high-dimensional data into
a lower-dimensional space with limited loss of information. One of
the most common forms of dimensionality reduction is the principal
components analysis (PCA). The 2DPCA is often called a variant of
principal component (PCA), the image matrices were directly treated
as 2D matrices; they do not need to be transformed into a vector so
that the covariance matrix of image can be constructed directly using
the original image matrices. The decomposed classical covariance
matrix is very sensitive to outlying observations. The objective of
paper is to compare the performance of robust minimizing vector
variance (MVV) in the two dimensional projection PCA (2DPCA)
and the PCA for clustering on an arbitrary data image when outliers
are hiden in the data set. The simulation aspects of robustness and
the illustration of clustering images are discussed in the end of
paper
Abstract: Traditional wind tunnel models are meticulously machined from metal in a process that can take several months. While very precise, the manufacturing process is too slow to assess a new design's feasibility quickly. Rapid prototyping technology makes this concurrent study of air vehicle concepts via computer simulation and in the wind tunnel possible. This paper described the Affects layer thickness models product with rapid prototyping on Aerodynamic Coefficients for Constructed wind tunnel testing models. Three models were evaluated. The first model was a 0.05mm layer thickness and Horizontal plane 0.1μm (Ra) second model was a 0.125mm layer thickness and Horizontal plane 0.22μm (Ra) third model was a 0.15mm layer thickness and Horizontal plane 4.6μm (Ra). These models were fabricated from somos 18420 by a stereolithography (SLA). A wing-body-tail configuration was chosen for the actual study. Testing covered the Mach range of Mach 0.3 to Mach 0.9 at an angle-of-attack range of -2° to +12° at zero sideslip. Coefficients of normal force, axial force, pitching moment, and lift over drag are shown at each of these Mach numbers. Results from this study show that layer thickness does have an effect on the aerodynamic characteristics in general; the data differ between the three models by fewer than 5%. The layer thickness does have more effect on the aerodynamic characteristics when Mach number is decreased and had most effect on the aerodynamic characteristics of axial force and its derivative coefficients.