Abstract: Reinforced concrete has good durability and excellent structural performance. But there are cases of early deterioration due to a number of factors, one prominent factor being corrosion of steel reinforcement. The process of corrosion sets in due to ingress of moisture, oxygen and other ingredients into the body of concrete, which is unsound, permeable and absorbent. Cracks due to structural and other causes such as creep, shrinkage, etc also allow ingress of moisture and other harmful ingredients and thus accelerate the rate of corrosion. There are several interactive factors both external and internal, which lead to corrosion of reinforcement and ultimately failure of structures. Suitable addition of mineral admixture like silica fume (SF) in concrete improves the strength and durability of concrete due to considerable improvement in the microstructure of concrete composites, especially at the transition zone. Secondary reinforcement in the form of fibre is added to concrete, which provides three dimensional random reinforcement in the entire mass of concrete. Reinforced concrete beams of size 0.1 m X 0.15 m and length 1m have been cast using M 35 grade of concrete. The beams after curing process were subjected to corrosion process by impressing an external Direct Current (Galvanostatic Method) for a period of 15 days under stressed and unstressed conditions. The corroded beams were tested by applying two point loads to determine the ultimate load carrying capacity and cracking pattern and the results of specimens were compared with that of the companion specimens. Gravimetric method is used to quantify corrosion that has occurred.
Abstract: The aim of this investigation is to study the
performance of the new generation of the PVD coated grade and to
map the influence of cutting conditions on the tool life in milling of
ADI (Austempered Ductile Iron). The results show that chipping is
the main wear mechanism which determines the tool life in dry
condition and notch wear in wet condition for this application. This
due to the different stress mechanisms and preexisting cracks in the
coating. The wear development shows clearly that the new PVD
coating (C20) has the best ability to delay the chipping growth. It
was also found that a high content of Al in the new coating (C20)
was especially favorable compared to a TiAlN multilayer with lower
Al content (C30) or CVD coating. This is due to fine grains and low
compressive stress level in the coating which increase the coating
ability to withstand the mechanical and thermal impact. It was also
found that the use of coolant decreases the tool life with 70-80%
compare to dry milling.
Abstract: Background Contact lens (CL) wear can cause
changes in blinking and corneal staining. Aims and Objectives To
determine the effects of CL materials (HEMA and SiHy) on
spontaneous blink rate, blinking patterns and corneal staining after 2
months of wear. Methods Ninety subjects in 3 groups (control,
HEMA and SiHy) were assessed at baseline and 2-months. Blink rate
was recorded using a video camera. Blinking patterns were assessed
with digital camera and slit lamp biomicroscope. Corneal staining
was graded using IER grading scale Results There were no significant
differences in all parameters at baseline. At 2 months, CL wearers
showed significant increment in average blink rate (F1.626, 47.141 =
7.250, p = 0.003; F2,58 = 6.240, p = 0.004) and corneal staining (χ2
2,
n=30 = 31.921, p < 0.001; χ2
2, n=30 = 26.909, p < 0.001). Conclusion
Blinking characteristics and corneal staining were not influence by
soft CL materials.
Abstract: We have modeled the effect of a graded band gap
window on the performance of a single junction AlxGa1-xAs/GaAs
solar cell. First, we study the electrical characteristics of a single
junction AlxGa1-xAs/GaAs solar cell, by employing an optimized
structure for this solar cell, we show that grading the band gap of the
window can increase the conversion efficiency of the solar cell by
about 1.5%, and can also improve the quantum efficiency of the solar
cell especially at shorter wavelengths.
Abstract: The electrical substation components are often subject to degradation due to over-voltage or over-current, caused by a short circuit or a lightning. A particular interest is given to the circuit breaker, regarding the importance of its function and its dangerous failure. This component degrades gradually due to the use, and it is also subject to the shock process resulted from the stress of isolating the fault when a short circuit occurs in the system. In this paper, based on failure mechanisms developments, the wear out of the circuit breaker contacts is modeled. The aim of this work is to evaluate its reliability and consequently its residual lifetime. The shock process is based on two random variables such as: the arrival of shocks and their magnitudes. The arrival of shocks was modeled using homogeneous Poisson process (HPP). By simulation, the dates of short-circuit arrivals were generated accompanied with their magnitudes. The same principle of simulation is applied to the amount of cumulative wear out contacts. The objective reached is to find the formulation of the wear function depending on the number of solicitations of the circuit breaker.
Abstract: A sophisticated simulator provides a cost-effective measure to carry out preliminary mission testing and diagnostic while reducing potential failures for real life at sea trials. The presented simulation framework covers three key areas: AUV modeling, sensor modeling, and environment modeling. AUV modeling mainly covers the area of AUV dynamics. Sensor modeling deals with physics and mathematical models that govern each sensor installed onto the AUV. Environment model incorporates the hydrostatic, hydrodynamics, and ocean currents that will affect the AUV in a real-time mission. Based on this designed simulation framework, custom scenarios provided by the user can be modeled and its corresponding behaviors can be observed. This paper focuses on the accuracy of the simulated data from AUV model and environmental model derived from a developed AUV test-bed which was jointly upgraded by DSTO and the University of Adelaide. The main contribution of this paper is to experimentally verify the accuracy of the proposed simulation framework.
Abstract: 17α-ethinylestradiol (EE2) is a recalcitrant micropollutant which is found in small amounts in municipal wastewater. But these small amounts still adversely affect for the reproductive function of aquatic organisms. Evidence in the past suggested that full-scale WWTPs equipped with nitrification process enhanced the removal of EE2 in the municipal wastewater. EE2 has been proven to be able to be transformed by ammonia oxidizing bacteria (AOB) via co-metabolism. This research aims to clarify the EE2 degradation pattern by different consortium of ammonia oxidizing microorganism (AOM) including AOA (ammonia oxidizing archaea) and investigate contribution between the existing ammonia monooxygenase (AMO) and new synthesized AOM. The result showed that AOA or AOB of N. oligotropha cluster in enriched nitrifying activated sludge (NAS) from 2mM and 5mM, commonly found in municipal WWTPs, could degrade EE2 in wastewater via co-metabolism. Moreover, the investigation of the contribution between the existing ammonia monooxygenase (AMO) and new synthesized AOM demonstrated that the new synthesized AMO enzyme may perform ammonia oxidation rather than the existing AMO enzyme or the existing AMO enzyme may has a small amount to oxidize ammonia.
Abstract: The purpose of this paper is to develop models that would enable predicting student success. These models could improve allocation of students among colleges and optimize the newly introduced model of government subsidies for higher education. For the purpose of collecting data, an anonymous survey was carried out in the last year of undergraduate degree student population using random sampling method. Decision trees were created of which two have been chosen that were most successful in predicting student success based on two criteria: Grade Point Average (GPA) and time that a student needs to finish the undergraduate program (time-to-degree). Decision trees have been shown as a good method of classification student success and they could be even more improved by increasing survey sample and developing specialized decision trees for each type of college. These types of methods have a big potential for use in decision support systems.
Abstract: The upgrading of low quality crude natural gas (NG) is attracting interest due to high demand of pipeline-grade gas in recent years. Membrane processes are commercially proven technology for the removal of impurities like carbon dioxide from NG. In this work, cross flow mathematical model has been suggested to be incorporated with ASPEN HYSYS as a user defined unit operation in order to design the membrane system for CO2/CH4 separation. The effect of operating conditions (such as feed composition and pressure) and membrane selectivity on the design parameters (methane recovery and total membrane area required for the separation) has been studied for different design configurations. These configurations include single stage (with and without recycle) and double stage membrane systems (with and without permeate or retentate recycle). It is shown that methane recovery can be improved by recycling permeate or retentate stream as well as by using double stage membrane systems. The ASPEN HYSYS user defined unit operation proposed in the study has potential to be applied for complex membrane system design and optimization.
Abstract: The aim of this study was to estimate the frequency of
EBV infection in Hodgkin's lymphoma (HL) and non-Hodgkin's
lymphoma (NHL) occurring in Jordanian patients. A total of 55
patients with lymphoma were examined in this study. Of 55 patients,
30 and 25 were diagnosed as HL and NHL, respectively. The four
HL subtypes were observed with the majority of the cases exhibited
the mixed cellularity (MC) subtype followed by the nodular sclerosis
(NS). The high grade was found to be the commonest subtype of
NHL in our sample, followed by the low grade. The presence of EBV
virus was detected by immunostating for expression of latent
membrane protein-1 (LMP-1). The frequency of LMP-1 expression
occurred more frequent in patients with HL (60.0%) than in patients
with NHL (32.0%). The frequency of LMP-1 expression was also
higher in patients with MC subtype (61.11%) than those patients with
NS (28.57%). No age or gender difference in occurrence of EBV
infection was observed among patient with HL. By contrast, the
prevalence of EBV infection in NHL patients aged below 50 was
lower (16.66%) than in NHL patients aged 50 or above (46.15%). In
addition, EBV infection was more frequent in females with NHL
(38.46%) than in male with NHL (25%). In NHL cases, the
frequency of EBV infection in intermediate grade (60.0%) was high
when compared with frequency of low (25%) or high grades (25%).
In conclusion, analysis of LMP-1 expression indicates an important
role for this viral oncogene in the pathogenesis of EBV-associated
malignant lymphomas. These data also support the previous findings
that people with EBV may develop lymphoma and that efforts to
maintain low lymphoma should be considered for people with EBV
infection.
Abstract: Information and communication service providers
(ICSP) that are significant in size and provide Internet-based services
take administrative, technical, and physical protection measures via
the information security check service (ISCS). These protection
measures are the minimum action necessary to secure the stability and
continuity of the information and communication services (ICS) that
they provide. Thus, information assets are essential to providing ICS,
and deciding the relative importance of target assets for protection is a
critical procedure. The risk analysis model designed to decide the
relative importance of information assets, which is described in this
study, evaluates information assets from many angles, in order to
choose which ones should be given priority when it comes to
protection. Many-sided risk analysis (MSRS) grades the importance of
information assets, based on evaluation of major security check items,
evaluation of the dependency on the information and communication
facility (ICF) and influence on potential incidents, and evaluation of
major items according to their service classification, in order to
identify the ISCS target. MSRS could be an efficient risk analysis
model to help ICSPs to identify their core information assets and take
information protection measures first, so that stability of the ICS can
be ensured.
Abstract: In the recent years, functionally gradient materials (FGMs) have gained considerable attention in the high temperature environment applications. In this paper, free vibration of thin functionally graded cylindrical shell with hole composed of stainless steel and zirconia is studied. The mechanical properties vary smoothly and continuously from one surface to the other according to a volume fraction power-law distribution. The Influence of shell geometrical parameters, variations of volume fractions and boundary conditions on natural frequency is considered. The equations of motion are based on strains-displacement relations from Love-s shell theory and Rayleigh method. The results have been obtained for natural frequencies of cylindrical shell with holes for different shape, number and location in this paper.
Abstract: This study aims to investigate mechanical behavior of
deep-drawn cups consisting of aluminum (A1050)/ duralumin
(A2017) multi-layered clad structures with micro- and macro-scale
functional gradients. Such multi-layered clad structures are possibly
used for a new type of crash-boxes in automobiles to effectively
absorb the impact forces generated when automobiles having
collisions. The effect of heat treatments on microstructure,
compositional gradient, micro hardness in 2 and 6-layered aluminum/
duralumin clad structures, which were fabricated by hot rolling, have
been investigated. Impact compressive behavior of deep-drawn cups
consisting of such aluminum/ duralumin clad structures has been also
investigated in terms of energy absorption and maximum force.
Deep-drawn cups consisting of 6-layerd clad structures with microand
macro-scale functional gradients exhibit superior properties in
impact compressive tests.
Abstract: Measurements of capacitance C and dissipation
factor tand of the stator insulation system provide useful information
about internal defects within the insulation. The index k is defined as
the proportionality constant between the changes at high voltage of
capacitance DC and of the dissipation factor Dtand . DC and
Dtand values were highly correlated when small flat defects were
within the insulation and that correlation was lost in the presence of
large narrow defects like electrical treeing. The discrimination
between small and large defects is made resorting to partial discharge
PD phase angle analysis. For the validation of the results, C and tand
measurements were carried out in a 15MVA 4160V steam turbine
turbogenerator placed in a sugar mill. In addition, laboratory test
results obtained by other authors were analyzed jointly. In such
laboratory tests, model coil bars subjected to thermal cycling resulted
highly degraded and DC and Dtand values were not correlated. Thus,
the index k could not be calculated.
Abstract: Asthma is a condition that causing chronic health problems in children. In addition to basic therapy against disease, we must try to reduce the impact of chronic health problems and also optimize their medical aspect of growth and development. A boy with mild asthma attack frequent episode did not showed any improvement with medical treatment and his asthma control test was 11. From radiologic examination he got hyperaerated lung and billateral sinusitis maxillaris; skin test results were house dust, food and pet allergy; an overweight body; bad school grades; psychological and environmental problem. We followed and evaluated this boy in 6 months, treated holistically. Even we could not do much on environmental but no more psychological and school problems, his on a good bodyweight and his asthma control test was 22. A case of a child with mild asthma attack frequent episode was reported. Asthma clinical course show no significant improvement when other predisposing factor is not well-controlled and a child’s growth and development may be affected. Improving condition of the patient can be created with the help of loving and caring way of nurturing from the parents and supportive peer group. Therefore, continuous and consistent monitoring is required because prognosis of asthma is generally good when regularly and properly controlled.
Abstract: This paper presents a research conducted to investigate the effect of mixing process on polypropylene (PP) modified bitumen mixed with well graded aggregate to form modified bituminous concrete mix. Two mode of mixing, namely dry and wet with different concentration of polymer polypropylene was used with 80/100 pen bitumen, to evaluate the bituminous concrete mix properties. Three percentages of polymer varying from 1-3% by the weight of bitumen was used in this study. Three mixes namely control mix, wet mix and dry mix were prepared. Optimum binder content was calculated considering Marshall Stability, flow, air voids and Marshall Quotient at different bitumen content varying from 4% - 6.5% for control, dry and wet mix. Engineering properties thus obtained at the calculated optimum bitumen content revealed that wet mixing process is advantageous in comparison to dry mixing as it increases the stiffness of the mixture with the increase in polymer content in bitumen. Stiffness value for wet mix increases with the increase in polymer content which is beneficial in terms of rutting. 1% PP dry mix also shows enhanced stiffness, with the air void content limited to 4%.The flow behaviour of dry mix doesn't indicate any major difference with the increase in polymer content revealing that polymer acting as an aggregate only without affecting the viscosity of the binder in the mix. Polypropylene (PP) when interacted with 80 pen base bitumen enhances its performance characteristics which were brought about by altered rheological properties of the modified bitumen. The decrease in flow with the increase in binder content reflects the increase in viscosity of binder which induces the plastic flow in the mix. Workability index indicates that wet mix were easy to compact up to desired void ratio in comparison to dry mix samples.
Abstract: This paper aims to present a survey of object
recognition/classification methods based on image moments. We
review various types of moments (geometric moments, complex
moments) and moment-based invariants with respect to various
image degradations and distortions (rotation, scaling, affine
transform, image blurring, etc.) which can be used as shape
descriptors for classification. We explain a general theory how to
construct these invariants and show also a few of them in explicit
forms. We review efficient numerical algorithms that can be used
for moment computation and demonstrate practical examples of
using moment invariants in real applications.
Abstract: The objective of this research was to study influence
parameters affecting to mechanical property of austenitic stainless
steel grade 304 (AISI 304) with Gas Metal Arc Welding (GMAW).
The research was applying factorial design experiment, which have
following interested parameters: welding current at 80, 90, and 100
Amps, welding speeds at 250, 300, and 350 mm/min, and shield gas
of 75% Ar + 25% CO2, 70% Ar + 25% CO2 + 5% O2 and 69.5% Ar +
25% CO2 + 5% O2 + 0.5% He gas. The study was done in following
aspects: ultimate tensile strength and elongation. A research study of
ultimate tensile strength found that main factor effect, which had the
highest strength to AISI 304 welding was shield gas of 70% Ar +
25% CO2 + 5% O2 at average of 954.81 N/mm2. Result of the highest
elongation was showed significantly different at interaction effect
between shield gas of 69.5%Ar+25%CO2+5%O2+.5%He and
welding speed at 250 mm/min at 47.94%.
Abstract: Due to some reasons, observed images are degraded which are mainly caused by noise. Recently image denoising using the wavelet transform has been attracting much attention. Waveletbased approach provides a particularly useful method for image denoising when the preservation of edges in the scene is of importance because the local adaptivity is based explicitly on the values of the wavelet detail coefficients. In this paper, we propose several methods of noise removal from degraded images with Gaussian noise by using adaptive wavelet threshold (Bayes Shrink, Modified Bayes Shrink and Normal Shrink). The proposed thresholds are simple and adaptive to each subband because the parameters required for estimating the threshold depend on subband data. Experimental results show that the proposed thresholds remove noise significantly and preserve the edges in the scene.
Abstract: The purpose of this study is to investigate the chemical
degradation of the organophosphorus pesticide of parathion and
carbamate insecticide of methomyl in the aqueous phase through
Fenton process. With the employment of batch Fenton process, the
degradation of the two selected pesticides at different pH, initial
concentration, humic acid concentration, and Fenton reagent dosages
was explored. The Fenton process was found effective to degrade
parathion and methomyl. The optimal dosage of Fenton reagents (i.e.,
molar concentration ratio of H2O2 to Fe2+) at pH 7 for parathion
degradation was equal to 3, which resulted in 50% removal of
parathion. Similarly, the optimal dosage for methomyl degradation
was 1, resulting in 80% removal of methomyl. This study also found
that the presence of humic substances has enhanced pesticide
degradation by Fenton process significantly. The mass spectroscopy
results showed that the hydroxyl free radical may attack the single
bonds with least energy of investigated pesticides to form smaller
molecules which is more easily to degrade either through
physio-chemical or bilolgical processes.