Abstract: Since columns are the most important elements of the
structures, failure of one column in a critical location can cause a
progressive collapse. In this respect, the repair and strengthening of
columns is a very important subject to reduce the building failure and
to keep the columns capacity. Twenty columns with different
parameters is tested and analysis. Eleven typical confined reinforced
concrete (RC) columns with different types of techniques are
assessment. And also, four confined concrete columns with plastic
tube (PVC) are tested with and with four paralleling tested of
unconfined plain concrete. The techniques of confined RC columns
are mortar strengthening, Steel rings strengthening, FRP
strengthening. Moreover, the technique of confined plain concrete
(PC) column is used PVC tubes. The columns are tested under
uniaxial compressive loads studied the effect of confinement on the
structural behavior of circular RC columns. Test results for each
column are presented in the form of crack patterns, stress-strain
curves. Test results show that confining of the RC columns using
different techniques of strengthening results significant improvement
of the general behavior of the columns and can used in construction.
And also, tested confined PC columns with PVC tubes results shown
that the confined PC with PVC tubes can be used in economical
building. The theoretical model for predicted column capacity is
founded with experimental factor depends on the confined techniques
used and the strain reduction.
Abstract: Stator elements «Vane diffuser + crossover + return
channel» of stages with different specific speed were investigated by
CFD calculations. The regime parameter was introduced to present
efficiency and loss coefficient performance of all elements together.
Flow structure demonstrated advantages and disadvantages of design.
Flow separation in crossovers was eliminated by its shape
modification. Efficiency increased visibly. Calculated CFD
performances are in acceptable correlation with predicted ones by
engineering design method. The information obtained is useful for
design method better calibration.
Abstract: The use of information tools is a common activity for
students of any educational stage when they encounter online
learning activities. Finding the relevant information for particular
learning tasks is the topic of this paper as it investigates the use of
information tools for a group of student participants. The paper
describes and discusses the results with particular implications for
use in higher education, and the findings suggest that improvement in
assessment design and subsequent student learning may be achieved
by structuring the purposefulness of information tools usage and
online reading behaviors of university students.
Abstract: Logistics processes of perishable food in the supply
chain include the distribution activities and the real time temperature
monitoring to fulfil the cold chain requirements. The paper presents
the use of RFID (Radio Frequency Identification) technology as an
identification tool of receiving and shipping activities in the cold
store. At the same time, the use of RFID data loggers with
temperature sensors is presented to observe and store the
temperatures for the purpose of analyzing the processes and having
the history data available for traceability purposes and efficient recall
management.
Abstract: A knowledge-based expert system with the acronym
RASPE is developed as an application tool to help decision makers in
construction companies make informed decisions about managing
risks in pipeline construction projects. Choosing to use expert
systems from all available artificial intelligence techniques is due to
the fact that an expert system is more suited to representing a
domain’s knowledge and the reasoning behind domain-specific
decisions. The knowledge-based expert system can capture the
knowledge in the form of conditional rules which represent various
project scenarios and potential risk mitigation/response actions. The
built knowledge in RASPE is utilized through the underlying
inference engine that allows the firing of rules relevant to a project
scenario into consideration. Paper provides an overview of the
knowledge acquisition process and goes about describing the
knowledge structure which is divided up into four major modules.
The paper shows one module in full detail for illustration purposes
and concludes with insightful remarks.
Abstract: This research focused on comparing the critical
thinking of the teacher students before and after using Miller’s Model
learning activities and investigating their opinions. The sampling
groups were (1) fourth year 33 student teachers majoring in Early
Childhood Education and enrolling in semester 1 of academic year
2013 (2) third year 28 student teachers majoring in English and
enrolling in semester 2 of academic year 2013 and (3) third year 22
student teachers majoring in Thai and enrolling in semester 2 of
academic year 2013. The research instruments were (1) lesson plans
where the learning activities were settled based on Miller’s Model (2)
critical thinking assessment criteria and (3) a questionnaire on
opinions towards Miller’s Model based learning activities. The
statistical treatment was mean, deviation, different scores and T-test.
The result unfolded that (1) the critical thinking of the students after
the assigned activities was better than before and (2) the students’
opinions towards the critical thinking improvement activities based
on Miller’s Model ranged from the level of high to highest.
Abstract: In this paper, two options of anodic alumina barrier
layer thinning have been demonstrated. The approaches varied with
the duration of the voltage step. It was found that too long step of the
barrier layer thinning process leads to chemical etching of the
nanopores on their top. At the bottoms pores are not fully opened
what is disadvantageous for further applications in nanofabrication.
On the other hand, while the duration of the voltage step is controlled
by the current density (value of the current density cannot exceed
75% of the value recorded during previous voltage step) the pores are
fully opened. However, pores at the bottom obtained with this
procedure have smaller diameter, nevertheless this procedure
provides electric contact between the bare aluminum (substrate) and
electrolyte, what is suitable for template assisted electrodeposition,
one of the most cost-efficient synthesis method in nanotechnology.
Abstract: The belief of a heavenly God is enshrined to all
Abrahamic religions which form the three major religions of the
world today. Muslims believe in Allah who is above the seven
heavens. The youth in the United Arab Emirates (UAE) study Islamic
courses as part of their high school curriculum and are required to
take at least one Islamic course at the university level to gain credit
hours towards their general education (GENED). This paper provides
an insight of what the youth studying in the UAE think of where
Allah is. Our analysis shows that a big number of Muslim youth were
not sure, especially those from the Middle Eastern and Arab countries
bringing to conclusion that this subject needs to be revisited again in
the course work.
Abstract: In this letter, we explore exact solutions for the
Horava-Lifshitz gravity. We use of an extension of this theory with
first order dynamical lapse function. The equations of motion have
been derived in a fully consistent scenario. We assume that there
are some spherically symmetric families of exact solutions of this
extended theory of gravity. We obtain exact solutions and investigate
the singularity structures of these solutions. Specially, an exact
solution with the regular horizon is found.
Abstract: Background: The effectiveness of mirror therapy
(MT) has been investigated in acute hemiplegia. The present study
examines whether MT, given during chronic stroke, was more
effective in promoting motor recovery of the lower extremity and
walking speed than standard rehabilitation alone. Methods: The study
enrolled 30 patients with chronic stroke. Fifteen patients each were
assigned to the treatment group and the control group. All patients
received a conventional rehabilitation program for a 4-week period.
In addition to this rehabilitation program, patients in the treatment
group received mirror therapy for 4 weeks, 5 days a week. Main
measures: Passive ankle joint dorsiflexion range of motion, gait
speed, Brunnstrom stages of motor recovery, plantar flexor muscle
tone by Modified Ashworth Scale. Results: No significant difference
was found in the outcome measures among groups before treatment.
When compared with standard rehabilitation, mirror therapy
improved Ankle ROM, Brunnstrom stages and waking speed
(p < 0.05). However, there were no significant differences between
two groups on MAS (P > 0.05).Conclusion: Mirror therapy combined
with a conventional stroke rehabilitation program enhances lowerextremity
motor recovery and walking speed in chronic stroke
patients.
Abstract: Interaction between human, location and activity
defines space. In the framework of these relations, space is a
container for current specifications in relations of the 3 mentioned
elements. The change of land utility considered with average
performance range, urban regulations, society requirements etc. will
provide welfare and comfort for citizens. From an engineering view it
is fundamental that choosing a proper location for a specific civil
activity requires evaluation of locations from different perspectives.
The debate of desirable establishment of municipal service elements
in urban regions is one of the most important issues related to urban
planning. In this paper, the research type is applicable based on goal,
and is descriptive and analytical based on nature. Initially existing
terminals in Esfahan are surveyed and then new locations are
presented based on evaluated criteria. In order to evaluate terminals
based on the considered factors, an AHP model is used at first to
estimate weight of different factors and then existing and suggested
locations are evaluated using Arc GIS software and AHP model
results. The results show that existing bus terminals are located in
fairly proper locations. Further results of this study suggest new
locations to establish terminals based on urban criteria.
Abstract: Sandwich structure composites produced by epoxy
core and aluminium skin were developed as potential building
materials. Interface bonding between core and skin was controlled by
varying kenaf content. Five different weight percentage of kenaf
loading ranging from 10 wt% to 50 wt% were employed in the core
manufacturing in order to study the mechanical properties of the
sandwich composite. Properties of skin aluminium with epoxy were
found to be affected by drying time of the adhesive. Mechanical
behavior of manufactured sandwich composites in relation with
properties of constituent materials was studied. It was found that 30
wt% of kenaf loading contributed to increase the flexural strength and
flexural modulus up to 102 MPa and 32 GPa, respectively. Analysis
were done on the flatwise and edgewise compression test. For
flatwise test, it was found that 30 wt% of fiber loading could
withstand maximum force until 250 kN, with compressive strength
results at 96.94 MPa. However, at edgewise compression test, the
sandwich composite with same fiber loading only can withstand 31
kN of the maximum load with 62 MPa of compressive strength
results.
Abstract: Fiber Bragg optic sensor is embedded in composite
material to detect and monitor the damage that occurs in composite
structures. In this paper, we deal with the mode-Ι delamination to
determine the material strength to crack propagation, using the
coupling mode theory and T-matrix method to simulate the FBGs
spectrum for both uniform and non-uniform strain distribution. The
double cantilever beam test is modeled in FEM to determine the
longitudinal strain. Two models are implemented, the first is the
global half model, and the second is the sub-model to represent the
FBGs with higher refined mesh. This method can simulate damage in
composite structures and converting strain to a wavelength shifting in
the FBG spectrum.
Abstract: Early detection of breast cancer saves many thousands
of lives each year via application of mammography and genetic
screening and many more lives could be saved if nurses are involved
in breast care screening practices. So, the aim of the study was to
identify nurse's role in early detection of breast cancer through
mammography and genetic screening and its impact on patient's
outcome. In order to achieve this aim, 400 women above 40 years,
asymptomatic were recruited for mammography and genetic
screening. In addition, 50 nurses and 6 technologists were involved in
the study. A descriptive analytical design was used. Five tools were
utilized: sociodemographic, mammographic examination and risk
factors, women's before, during and after mammography, items
relaying to technologists, and items related to nurses were also
obtained. The study finding revealed that 3% of women detected for
malignancy and 7.25% for fibroadenoma. Statistically significant
differences were found between mammography results and age,
family history, genetic screening, exposure to smoke, and using
contraceptive pills. Nurses have insufficient knowledge about
screening tests. Based on these findings the present study
recommended involvement of nurses in breast care which is very
important to in force population about screening practices.
Abstract: Speech enhancement is a long standing problem with
numerous applications like teleconferencing, VoIP, hearing aids and
speech recognition. The motivation behind this research work is to
obtain a clean speech signal of higher quality by applying the optimal
noise cancellation technique. Real-time adaptive filtering algorithms
seem to be the best candidate among all categories of the speech
enhancement methods. In this paper, we propose a speech
enhancement method based on Recursive Least Squares (RLS)
adaptive filter of speech signals. Experiments were performed on
noisy data which was prepared by adding AWGN, Babble and Pink
noise to clean speech samples at -5dB, 0dB, 5dB and 10dB SNR
levels. We then compare the noise cancellation performance of
proposed RLS algorithm with existing NLMS algorithm in terms of
Mean Squared Error (MSE), Signal to Noise ratio (SNR) and SNR
Loss. Based on the performance evaluation, the proposed RLS
algorithm was found to be a better optimal noise cancellation
technique for speech signals.
Abstract: The Standard Penetration Test (SPT) is the most
common in situ test for soil investigations. On the other hand, the
Cone Penetration Test (CPT) is considered one of the best
investigation tools. Due to the fast and accurate results that can be
obtained it complaints the SPT in many applications like field
explorations, design parameters, and quality control assessments.
Many soil index and engineering properties have been correlated to
both of SPT and CPT. Various foundation design methods were
developed based on the outcome of these tests. Therefore it is vital to
correlate these tests to each other so that either one of the tests can be
used in the absence of the other, especially for preliminary evaluation
and design purposes.
The primary purpose of this study was to investigate the
relationships between the SPT and CPT for different type of sandy
soils in Florida. Data for this research were collected from number of
projects sponsored by the Florida Department of Transportation
(FDOT), six sites served as the subject of SPT-CPT correlations. The
correlations were established between the cone resistance (qc), sleeve
friction (fs) and the uncorrected SPT blow counts (N) for various
soils.
A positive linear relationship was found between qc, fs and N for
various sandy soils. In general, qc versus N showed higher
correlation coefficients than fs versus N. qc/N ratios were developed
for different soil types and compared to literature values, the results
of this research revealed higher ratios than literature values.
Abstract: The industrial process adds to engineering wood
products features absent in solid wood, with homogeneous structure
and reduced defects, improved physical and mechanical properties,
bio-deterioration, resistance and better dimensional stability,
improving quality and increasing the reliability of structures wood.
These features combined with using fast-growing trees, make them
environmentally ecological products, ensuring a strong consumer
market. The wood I-joists are manufactured by the industrial profiles
bonding flange and web, an important aspect of the production of
wooden I-beams is the adhesive joint that bonds the web to the
flange. Adhesives can effectively transfer and distribute stresses,
thereby increasing the strength and stiffness of the composite. The
objective of this study is to evaluate different resins in a shear strain
specimens with the aim of analyzing the most efficient resin and
possibility of using national products, reducing the manufacturing
cost. First was conducted a literature review, where established the
geometry and materials generally used, then established and analyzed
8 national resins and produced six specimens for each.
Abstract: The western Tombolo of the Giens peninsula in
southern France, known as Almanarre beach, is subject to coastal
erosion. We are trying to use computer simulation in order to propose
solutions to stop this erosion. Our aim was first to determine the main
factors for this erosion and successfully apply a coupled hydrosedimentological
numerical model based on observations and
measurements that have been performed on the site for decades.
We have gathered all available information and data about waves,
winds, currents, tides, bathymetry, coastal line, and sediments
concerning the site. These have been divided into two sets: one
devoted to calibrating a numerical model using Mike 21 software, the
other to serve as a reference in order to numerically compare the
present situation to what it could be if we implemented different
types of underwater constructions.
This paper presents the first part of the study: selecting and
melting different sources into a coherent data basis, identifying the
main erosion factors, and calibrating the coupled software model
against the selected reference period.
Our results bring calibration of the numerical model with good
fitting coefficients. They also show that the winter South-Western
storm events conjugated to depressive weather conditions constitute a
major factor of erosion, mainly due to wave impact in the northern
part of the Almanarre beach. Together, current and wind impact is
shown negligible.
Abstract: The tombolo of Giens is located in the town of Hyères
(France). We recall the history of coastal erosion, and prominent
factors affecting the evolution of the western tombolo. We then
discuss the possibility of stabilizing the western tombolo. Our
argumentation relies on a coupled model integrating swells, currents,
water levels and sediment transport. We present the conclusions of
the simulations of various scenarios, including pre-existing
propositions from coastal engineering offices. We conclude that
beach replenishment seems to be necessary but not sufficient for the
stabilization of the beach. Breakwaters reveal effective particularly in
the most exposed northern area. Some solutions fulfill conditions so
as to be elected as satisfactory. We give a comparative analysis of the
efficiency of 14 alternatives for the protection of the tombolo.
Abstract: The Great East Japan Earthquake occurred at 14:46 on Friday, March 11, 2011. It was the most powerful known earthquake to have hit Japan. The earthquake triggered extremely destructive tsunami waves of up to 40.5 meters in height. We focus on the ship’s evacuation from tsunami. Then we analyze about ships evacuation from tsunami using multi-agent simulation and we want to prepare for a coming earthquake. We developed a simulation model of ships that set sail from the port in order to evacuate from the tsunami considering the ship carrying dangerous goods.