Abstract: The power consumption of an Optical Packet Switch
equipped with SOA technology based Spanke switching fabric is
evaluated. Sophisticated analytical models are introduced to evaluate
the power consumption versus the offered traffic, the main
switch parameters, and the used device characteristics. The impact
of Amplifier Spontaneous Emission (ASE) noise generated by a
transmission system on the power consumption is investigated. As
a matter of example for 32×32 switches supporting 64 wavelengths
and offered traffic equal to 0,8, the average energy consumption per
bit is 5, 07 · 10-2 nJ/bit and increases if ASE noise introduced by
the transmission systems is increased.
Abstract: In this study we investigate silica nanoparticle (SiO2- NP) effects on the structure and phase properties of supported lipid monolayers and bilayers, coupling surface pressure measurements, fluorescence microscopy and atomic force microscopy. SiO2-NPs typically in size range of 10nm to 100 nm in diameter are tested. Our results suggest first that lipid molecules organization depends to their nature. Secondly, lipid molecules in the vinicity of big aggregates nanoparticles organize in liquid condensed phase whereas small aggregates are localized in both fluid liquid-expanded (LE) and liquid-condenced (LC). We demonstrated also by atomic force microscopy that by measuring friction forces it is possible to get information as if nanoparticle aggregates are recovered or not by lipid monolayers and bilayers.
Abstract: As originally designed for wired networks, TCP (transmission control protocol) congestion control mechanism is triggered into action when packet loss is detected. This implicit assumption for packet loss mostly due to network congestion does not work well in Mobile Ad Hoc Network, where there is a comparatively high likelihood of packet loss due to channel errors and node mobility etc. Such non-congestion packet loss, when dealt with by congestion control mechanism, causes poor TCP performance in MANET. In this study, we continue to investigate the impact of the interaction between transport protocols and on-demand routing protocols on the performance and stability of 802.11 multihop networks. We evaluate the important wireless networking events caused routing change, and propose a cross layer method to delay the unnecessary routing changes, only need to add a sensitivity parameter α , which represents the on-demand routing-s reaction to link failure of MAC layer. Our proposal is applicable to the plain 802.11 networking environment, the simulation results that this method can remarkably improve the stability and performance of TCP without any modification on TCP and MAC protocol.
Abstract: This paper presents a methodology towards the emulation of the electrical power consumption of the RF device during the cellular phone/handset transmission mode using the LTE technology. The emulation methodology takes the physical environmental variables and the logical interface between the baseband and the RF system as inputs to compute the emulated power dissipation of the RF device. The emulated power, in between the measured points corresponding to the discrete values of the logical interface parameters is computed as a polynomial interpolation using polynomial basis functions. The evaluation of polynomial and spline curve fitting models showed a respective divergence (test error) of 8% and 0.02% from the physically measured power consumption. The precisions of the instruments used for the physical measurements have been modeled as intervals. We have been able to model the power consumption of the RF device operating at 5MHz using homotopy between 2 continuous power consumptions of the RF device operating at the bandwidths 3MHz and 10MHz.
Abstract: We present a new approach to evaluation of Cyber Security in Power Systems using the method of modeling the power systems Infrastructure using software agents. Interfaces between module and the home smart meter are recognized as the primary points of intrusion.
Abstract: The hydraulic actuated excavator, being a non-linear
mobile machine, encounters many uncertainties. There are
uncertainties in the hydraulic system in addition to the uncertain
nature of the load. The simulation results obtained in this study show
that there is a need for intelligent control of such machines and in
particular interval type-2 fuzzy controller is most suitable for
minimizing the position error of a typical excavator-s bucket under
load variations. We consider the model parameter uncertainties such
as hydraulic fluid leakage and friction. These are uncertainties which
also depend up on the temperature and alter bulk modulus and
viscosity of the hydraulic fluid. Such uncertainties together with the
load variations cause chattering of the bucket position. The interval
type-2 fuzzy controller effectively eliminates the chattering and
manages to control the end-effecter (bucket) position with positional
error in the order of few millimeters.
Abstract: In this paper, the issue of pth moment exponential stability of stochastic recurrent neural network with distributed time delays is investigated. By using the method of variation parameters, inequality techniques, and stochastic analysis, some sufficient conditions ensuring pth moment exponential stability are obtained. The method used in this paper does not resort to any Lyapunov function, and the results derived in this paper generalize some earlier criteria reported in the literature. One numerical example is given to illustrate the main results.
Abstract: Herein, the organic semiconductor methyl orange
(MO), is investigated for the first time for its electronic applications.
For this purpose, Al/MO/n-Si heterojunction is fabricated through
economical cheap and simple “drop casting” technique. The currentvoltage
(I-V) measurements of the device are made at room
temperature under dark conditions. The I-V characteristics of
Al/MO/n-Si junction exhibits asymmetrical and rectifying behavior
that confirms the formation of diode. The diode parameters such as
rectification ratio (RR), turn on voltage (Vturn on), reverse saturation
current (I0), ideality factor (n), barrier height ( b
f ), series resistance
(Rs) and shunt resistance (Rsh) are determined from I-V curves using
Schottky equations. These values of these parameters are also
extracted and verified by applying Cheung’s functions. The
conduction mechanisms are explained from the forward bias I-V
characteristics using the power law.
Abstract: This paper investigates the development of weld zone
in Resistance Spot Welding (RSW) which focuses on weld nugget and Heat Affected Zone (HAZ). The effects of four factors namely
weld current, weld time, electrode force and hold time were studied using a general 24 factorial design augmented by five centre points. The results of the analysis showed that all selected factors except
hold time exhibit significant effect on weld nugget radius and HAZ size. Optimization of the welding parameters (weld current, weld
time and electrode force) to normalize weld nugget and to minimize
HAZ size was then conducted using Central Composite Design (CCD) in Response Surface Methodology (RSM) and the optimum
parameters were determined. A regression model for radius of weld nugget and HAZ size was developed and its adequacy was evaluated.
The experimental results obtained under optimum operating conditions were then compared with the predicted values and were
found to agree satisfactorily with each other
Abstract: Heat source addition to the axisymmetric supersonic
inlet may improve the performance parameters, which will increase
the inlet efficiency. In this investigation the heat has been added to
the flow field at some distance ahead of an axisymmetric inlet by
adding an imaginary thermal source upstream of cowl lip. The effect
of heat addition on the drag coefficient, mass flow rate and the
overall efficiency of the inlet have been investigated. The results
show that heat addition causes flow separation, hence to prevent this
phenomena, roughness has been added on the spike surface.
However, heat addition reduces the drag coefficient and the inlet
mass flow rate considerably. Furthermore, the effects of position,
size, and shape on the inlet performance were studied. It is found that
the thermal source deflects the flow streamlines. By improper
location of the thermal source, the optimum condition has been
obtained. For the optimum condition, the drag coefficient is
considerably reduced and the inlet mass flow rate and its efficiency
have been increased slightly. The optimum shape of the heat source
is obtained too.
Abstract: By taking advantage of computer-s processing power, an unlimited number of variations and parameters in both spatial and environmental can be provided while following the same set of rules and constraints. This paper focuses on using the tools of parametric urbanism towards a more responsive environmental and sustainable urban morphology. It presents an understanding to Parametric Urban Comfort Envelope (PUCE) as an interactive computational assessment urban model. In addition, it investigates the applicability potentials of this model to generate an optimized urban form to Borg El Arab city (a new Egyptian Community) concerning the human comfort values specially wind and solar envelopes. Finally, this paper utilizes its application outcomes -both visual and numerical- to extend the designer-s limitations by decrease the concern of controlling and manipulation of geometry, and increase the designer-s awareness about the various potentials of using the parametric tools to create relationships that generate multiple geometric alternatives.
Abstract: Steel made pipelines with different diameters are used
for transmitting oil and gas which in many cases are buried in soil
under the sea bed or immersed in sea water. External corrosion of
pipes is an important form of deterioration due to the aggressive
environment of sea water. Corrosion normally results in pits. Hence,
using the finite element method, namely ABAQUS software, this
paper estimates the amount of pressure capacity reduction of a pipecontaining
a semi-elliptical pitting corrosion and the rate of corrosion
during the pipeline life of 25 years.
Abstract: The present work represents an investigation of the
hydrolysis of hull-less pumpkin (Cucurbita Pepo L.) oil cake protein
isolate (PuOC PI) by pepsin. To examine the effectiveness and
suitability of pepsin towards PuOC PI the kinetic parameters for
pepsin on PuOC PI were determined and then, the hydrolysis process
was studied using Response Surface Methodology (RSM). The
hydrolysis was carried out at temperature of 30°C and pH 3.00. Time
and initial enzyme/substrate ratio (E/S) at three levels were selected
as the independent parameters. The degree of hydrolysis, DH, was
mesuared after 20, 30 and 40 minutes, at initial E/S of 0.7, 1 and 1.3
mA/mg proteins. Since the proposed second-order polynomial model
showed good fit with the experimental data (R2 = 0.9822), the
obtained mathematical model could be used for monitoring the
hydrolysis of PuOC PI by pepsin, under studied experimental
conditions, varying the time and initial E/S. To achieve the highest
value of DH (39.13 %), the obtained optimum conditions for time
and initial E/S were 30 min and 1.024 mA/mg proteins.
Abstract: Estimation time and cost of work completion in a
project and follow up them during execution are contributors to
success or fail of a project, and is very important for project
management team. Delivering on time and within budgeted cost
needs to well managing and controlling the projects. To dealing with
complex task of controlling and modifying the baseline project
schedule during execution, earned value management systems have
been set up and widely used to measure and communicate the real
physical progress of a project. But it often fails to predict the total
duration of the project. In this paper data mining techniques is used
predicting the total project duration in term of Time Estimate At
Completion-EAC (t). For this purpose, we have used a project with
90 activities, it has updated day by day. Then, it is used regular
indexes in literature and applied Earned Duration Method to
calculate time estimate at completion and set these as input data for
prediction and specifying the major parameters among them using
Clem software. By using data mining, the effective parameters on
EAC and the relationship between them could be extracted and it is
very useful to manage a project with minimum delay risks. As we
state, this could be a simple, safe and applicable method in prediction
the completion time of a project during execution.
Abstract: Response surface methodology (RSM) is a very
efficient tool to provide a good practical insight into developing new
process and optimizing them. This methodology could help
engineers to raise a mathematical model to represent the behavior of
system as a convincing function of process parameters.
Through this paper the sequential nature of the RSM surveyed for process
engineers and its relationship to design of experiments (DOE), regression
analysis and robust design reviewed. The proposed four-step procedure in
two different phases could help system analyst to resolve the parameter
design problem involving responses. In order to check accuracy of the
designed model, residual analysis and prediction error sum of squares
(PRESS) described.
It is believed that the proposed procedure in this study can resolve a
complex parameter design problem with one or more responses. It can be
applied to those areas where there are large data sets and a number of
responses are to be optimized simultaneously. In addition, the proposed
procedure is relatively simple and can be implemented easily by using
ready-made standard statistical packages.
Abstract: Segmentation and quantification of stenosis is an
important task in assessing coronary artery disease. One of the main
challenges is measuring the real diameter of curved vessels.
Moreover, uncertainty in segmentation of different tissues in the
narrow vessel is an important issue that affects accuracy. This paper
proposes an algorithm to extract coronary arteries and measure the
degree of stenosis. Markovian fuzzy clustering method is applied to
model uncertainty arises from partial volume effect problem. The
algorithm employs: segmentation, centreline extraction, estimation of
orthogonal plane to centreline, measurement of the degree of
stenosis. To evaluate the accuracy and reproducibility, the approach
has been applied to a vascular phantom and the results are compared
with real diameter. The results of 10 patient datasets have been
visually judged by a qualified radiologist. The results reveal the
superiority of the proposed method compared to the Conventional
thresholding Method (CTM) on both datasets.
Abstract: In this paper, the concepts of dichotomous logistic
regression (DLR) with leave-one-out (L-O-O) were discussed. To
illustrate this, the L-O-O was run to determine the importance of the
simulation conditions for robust test of spread procedures with good
Type I error rates. The resultant model was then evaluated. The
discussions included 1) assessment of the accuracy of the model, and
2) parameter estimates. These were presented and illustrated by
modeling the relationship between the dichotomous dependent
variable (Type I error rates) with a set of independent variables (the
simulation conditions). The base SAS software containing PROC
LOGISTIC and DATA step functions can be making used to do the
DLR analysis.
Abstract: Numerical studies have been carried out using a
validated two-dimensional RNG k-epsilon turbulence model for the
design optimization of a thrust vector control system using shock
induced supersonic secondary jet. Parametric analytical studies have
been carried out with various secondary jets at different divergent
locations, jet interaction angles, jet pressures. The results from the
parametric studies of the case on hand reveal that the primary nozzle
with a small divergence angle, downstream injections with a distance
of 2.5 times the primary nozzle throat diameter from the primary
nozzle throat location warrant higher efficiency over a certain range
of jet pressures and jet angles. We observed that the supersonic
secondary jet opposing the core flow with jets interaction angle of
40o to the axis far downstream of the nozzle throat facilitates better
thrust vectoring than the secondary jet with same direction as that of
core flow with various interaction angles. We concluded that fixing
of the supersonic secondary jet nozzle pointing towards the throat
direction with suitable angle at a distance 2 to 4 times of the primary
nozzle throat diameter, as the case may be, from the primary nozzle
throat location could facilitate better thrust vectoring for the
supersonic aerospace vehicles.
Abstract: Since hyaluronic acid (HA) receptor such as CD44 is
over-expressed at sites of cancer cells, HA can be used as a targeting
vehicles for anti-cancer drugs. The aim of this study is to synthesize
block copolymer composed of hyaluronic acid and
poly(ε-caprolactone) (HAPCL) and to fabricate polymeric micelles for
anticancer drug targeting against CD44 receptor of tumor cells.
Chemical composition of HAPCL was confirmed using 1H NMR
spectroscopy. Doxorubicin (DOX) was incorporated into polymeric
micelles of HAPCL. The diameters of HAPHS polymeric micelles
were changed around 80nm and have spherical shapes. Targeting
potential was investigated using CD44-overexpressing. When
DOX-incorporated polymeric micelles was added to KB cells, they
revealed strong red fluorescence color while blocking of CD44
receptor by pretreatment of free HA resulted in reduced intensity,
indicating that HAPCL polymeric micelles have targetability against
CD44 receptor.
Abstract: The optimal grid spacing and turbulence model for the
2D numerical analysis of a vertical-axis water turbine (VAWaterT)
operating in a 2 m/s freestream current has been investigated. The
results of five different spatial domain discretizations and two
turbulence models (k-ω SST and k-ε RNG) have been compared, in
order to gain the optimal y+ parameter distribution along the blade
walls during a full rotor revolution. The resulting optimal mesh has
appeared to be quite similar to that obtained for the numerical
analysis of a vertical-axis wind turbine.