Abstract: In this paper, snow samples containing dust particles
from several sampling points around the city of Ostrava were
analyzed. The pH values of sampled snow were measured and solid
particles analyzed. Particle size, zeta potential and content of selected
heavy metals were determined in solid particles. The pH values of
most samples lay in the slightly acid region. Mean values of particle
size ranged from 290.5 to 620.5 nm. Zeta potential values varied
between -5 and -26.5 mV. The following heavy metal concentration
ranges were found: copper 0.08-0.75 mg/g, lead 0.05-0.9 mg/g,
manganese 0.45-5.9 mg/g and iron 25.7-280.46 mg/g. The highest
values of copper and lead were found in the vicinity of busy
crossroads, and on the contrary, the highest levels of manganese and
iron were detected close to a large steelworks. The proportion
between pH values, zeta potentials, particle sizes and heavy metal
contents was established. Zeta potential decreased with rising pH
values and, simultaneously, heavy metal content in solid particles
increased. At the same time, higher metal content corresponded to
lower particle size.
Abstract: In this paper, the effect of WC-12Co particle
temperature in HVOF thermal spraying process on the coating
thickness has been studied. The statistical results show that the spray
distance and oxygen-to-fuel ratio are effective factors on particle
characterization and thickness of HVOF thermal spraying coatings.
Spray Watch diagnostic system, scanning electron microscopy
(SEM), X-ray diffraction and thickness measuring system were used
for this purpose.
Abstract: The parameters of a two-layer soil can be determined by
processing resistivity data obtained from resistivity measurements
carried out on the soil of interest. The processing usually entails
applying the resistivity data as inputs to an optimisation function.
This paper proposes an algorithm which utilises the square error as an
optimisation function. Resistivity data from previous works were
applied to test the accuracy of the new algorithm developed and the
result obtained conforms significantly to results from previous works.
Abstract: A novel simulation method to determine the
displacements of machine tools due to thermal factors is presented.
The specific characteristic of this method is the employment of
original CAD data from the design process chain, which is
interpreted by an algorithm in terms of geometry-based allocation of
convection and radiation parameters. Furthermore analogous models
relating to the thermal behaviour of machine elements are
automatically implemented, which were gained by extensive
experimental testing with thermography imaging. With this a
transient simulation of the thermal field and in series of the
displacement of the machine tool is possible simultaneously during
the design phase. This method was implemented and is already used
industrially in the design of machining centres in order to improve
the quality of herewith manufactured workpieces.
Abstract: Mech-Degla, Degla-Beida and Frezza are the date
(Phoenix dactylifera L.) common varieties with a more or less good
availability and feeble trade value. Some morphologic and
physicochemical factors were determined. Results show that the
whole date weight is significantly different (P= 95%) concerning
Mech-Degla and Degla-Beida which are more commercialized than
Frezza whereas the pulp mass proportion in relation to whole fruits is
highest for Frezza (88.28%). Moreover, there is a large variability
concerning the weights and densities of constitutive tissues in each
variety. The white tissue is dominant in Mech-Degla in opposite to
the two other varieties. The variance analyze showed that the
difference in weights between brown and white tissues is significant
(P = 95%) for all studied varieties. Some other morphologic and
chemical proprieties of the whole pulps and their two constitutive
parts (brown or pigmented and white) are also investigated. The
predominance of phenolics in Mech-Degla (4.01g/100g, w.b) and
Frezza (4.96 g/100g, w.b) pulps brown part is the main result
revealed in this study.
Abstract: Identification and selection of appropriate product and
manufacturing technologies are key factors for competitiveness and
market success of technology-based companies. Therefore, many
companies perform technology intelligence (TI) activities to ensure
the identification of evolving technologies at the right time.
Technology monitoring is one of the three base activities of TI,
besides scanning and scouting.
As the technological progress is accelerating, more and more
technologies are being developed. Against the background of limited
resources it is therefore necessary to focus TI activities. In this paper
we propose a concept for defining appropriate search fields for
technology monitoring. This limitation of search space leads to more
concentrated monitoring activities. The concept will be introduced
and demonstrated through an anonymized case study conducted
within an industry project at the Fraunhofer Institute for Production
Technology IPT.
The described concept provides a customized monitoring
approach, which is suitable for use in technology-oriented companies.
It is shown in this paper that the definition of search fields and search
tasks are suitable methods to define topics of interest and thus to
align monitoring activities. Current as well as planned product,
production and material technologies and existing skills, capabilities
and resources form the basis for derivation of relevant search areas.
To further improve the concept of technology monitoring the
proposed concept should be extended during future research e.g. by
the definition of relevant monitoring parameters.
Abstract: Online forum is part of a Learning Management
System (LMS) environment in which students share their opinions.
This study attempts to investigate the perceptions of students towards
online forum and their patterns of listening behavior during the forum
interaction. The students’ perceptions were measured using a
questionnaire, in which seven dimensions were used involving online
experience, benefits of forum participation, cost of participation,
perceived ease of use, usefulness, attitude, and intention. Meanwhile,
their patterns of listening behaviors were obtained using the log file
extracted from the LMS. A total of 25 postgraduate students
undertaking a course were involved in this study, and their activities
in the forum session were recorded by the LMS and used as a log file.
The results from the questionnaire analysis indicated that the students
perceived that the forum is easy to use, useful, and bring benefits to
them. Also, they showed positive attitude towards online forum, and
they have the intention to use it in future. Based on the log data, the
participants were also divided into six clusters of listening behavior,
in which they are different in terms of temporality, breadth, depth and
speaking level. The findings were compared to previous clusters
grouping and future recommendations are also discussed.
Abstract: A study was conducted to determine the diversity and
abundance of shorebird species habituating the mudflat area of Jeram
Beach and Remis Beach, Selangor, Peninsular Malaysia. Direct
observation technique (using binoculars and video camera) was
applied to record the presence of bird species in the sampling sites
from August 2013 until July 2014. A total of 32 species of shorebird
were recorded during both migratory and non-migratory seasons. Of
these, eleven species (48%) are migrants, six species (26%) have both
migrant and resident populations, four species (17%) are vagrants and
two species (9%) are residents. The compositions of the birds
differed significantly in all months (χ2 = 84.35, p < 0.001). There is a
significant difference in avian abundance between migratory and
non-migratory seasons (Mann-Whitney, t = 2.39, p = 0.036). The
avian abundance were differed significantly in Jeram and Remis
Beaches during migratory periods (t = 4.39, p = 0.001) but not during
non-migratory periods (t = 0.78, p = 0.456). Shorebird diversity was
also affected by tidal cycle. There is a significance difference
between high tide and low tide (Mann-Whitney, t = 78.0, p < 0.005).
Frequency of disturbance also affected the shorebird distribution
(Mann-Whitney, t = 57.0, p = 0.0134). Therefore, this study
concluded that tides and disturbances are two factors that affecting
temporal distribution of shorebird in mudflats area.
Abstract: Ancillary services are support services which are
essential for humanizing and enhancing the reliability and security of
the electric power system. Reactive power ancillary service is one of
the important ancillary services in a restructured electricity market
which determines the cost of supplying ancillary services and finding
of how this cost would change with respect to operating decisions.
This paper presents a new formation that can be used to minimize the
Independent System Operator (ISO)’s total payment for reactive
power ancillary service. The modified power flow tracing algorithm
estimates the availability of reserve reactive power for ancillary
service. In order to find optimum reactive power dispatch,
Biogeography based optimization method (BPO) is proposed. Market
Reactive Clearing Price (MRCP) is then estimated and it encourages
generator companies (GENCOs) to participate in an ancillary service.
Finally, optimal weighting factor and real time utilization factor of
reactive power give the minimum ISO’s total payment. The
effectiveness of proposed design is verified using IEEE 30 bus
system.
Abstract: This paper considers the characterization of a complex
electromagnetic environment due to multiple sources of
electromagnetic radiation as a five-dimensional surface which can be
described by a set of several surface sections including: instant EM
field intensity distribution maps at a given frequency and altitude,
instantaneous spectrum at a given location in space and the time
evolution of the electromagnetic field spectrum at a given point in
space. This characterization if done over time can enable the
exposure levels of Radio Frequency Radiation at every point in the
analysis area to be determined and results interpreted based on
comparison of the determined RFR exposure level with the safe
guidelines for general public exposure given by recognized body
such as the International commission on non-ionizing radiation
protection (ICNIRP), Institute of Electrical and Electronic Engineers
(IEEE), the National Radiation Protection Authority (NRPA).
Abstract: In this paper the effect of wall waviness of side walls
in a two-dimensional wavy enclosure is numerically investigated.
Two vertical wavy walls and straight top wall are kept isothermal and
the bottom wall temperature is higher and spatially varying with
cosinusoidal temperature distribution. A computational code based on
Finite-volume approach is used to solve governing equations and
SIMPLE method is used for pressure velocity coupling. Test is
performed for several different numbers of undulations. The Prandtl
number was kept constant and the Ra number denotes that the flow is
laminar. Temperature and velocity fields are determined. Therefore,
according to the obtained results a correlation is proposed for average
Nusselt number as a function of number of side wall waves. The
results indicate that the Nusselt number is highly affected by number
of waves and increasing it decreases the wavy walls Nusselt number;
although the Nusselt number is not highly affected by surface
waviness when the number of undulations is below one.
Abstract: This paper presents a 4-DOF nonlinear model of a
cracked de Laval rotor-stator system derived based on Energy
Principles. The model has been used to simulate coupled torsionallateral
response of the faulty system with multiple parametric
excitations; rotor-stator-rub, a breathing transverse crack, eccentric
mass and an axial force. Nonlinearity of a “breathing” crack is
incorporated in the model using a simple hinge mechanism suitable
for a shallow crack. Response of the system while passing via its
critical speed with intermittent rotor-stator rub is analyzed. Effects of
eccentricity with phase and acceleration are investigated. Features of
crack, rub and eccentricity in vibration response are explored for
condition monitoring. The presence of a crack and rub are observable
in the power spectrum despite excitations by an axial force and rotor
unbalance. Obtained results are consistent with existing literature and
could be adopted into rotor condition monitoring strategies.
Abstract: The article discusses multimodal mobility in
contemporary societies as a main planning and organization issue in
the functioning of administrative bodies, a problem which really
exists in the space of contemporary cities in terms of shaping modern
transport systems. The article presents classification of available
resources and initiatives undertaken for developing multimodal
mobility. Solutions can be divided into three groups of measures –
physical measures in the form of changes of the transport network
infrastructure, organizational ones (including transport policy) and
information measures. The latter ones include in particular direct
support for people travelling in the transport network by providing
information about ways of using available means of transport. A
special measure contributing to this end is a trip planner. The article
compares several selected planners. It includes a short description of
the Green Travelling Project, which aims at developing a planner
supporting environmentally friendly solutions in terms of transport
network operation. The article summarizes preliminary findings of
the project.
Abstract: A relationship between face and signature biometrics
is established in this paper. A new approach is developed to predict
faces from signatures by using artificial intelligence. A multilayer
perceptron (MLP) neural network is used to generate face details
from features extracted from signatures, here face is the physical
biometric and signatures is the behavioural biometric. The new
method establishes a relationship between the two biometrics and
regenerates a visible face image from the signature features.
Furthermore, the performance efficiencies of our new technique are
demonstrated in terms of minimum error rates compared to published
work.
Abstract: reliability-based methodology for the assessment
and evaluation of reinforced concrete (R/C) structural elements of
concrete structures is presented herein. The results of the reliability
analysis and assessment for R/C structural elements were verified by
the results obtained through deterministic methods. The outcomes of
the reliability-based analysis were compared against currently
adopted safety limits that are incorporated in the reliability indices
β’s, according to international standards and codes. The methodology
is based on probabilistic analysis using reliability concepts and
statistics of the main random variables that are relevant to the subject
matter, and for which they are to be used in the performance-function
equation(s) associated with the structural elements under study.
These methodology techniques can result in reliability index β, which
is commonly known as the reliability index or reliability measure
value that can be utilized to assess and evaluate the safety, human
risk, and functionality of the structural component. Also, these
methods can result in revised partial safety factor values for certain
target reliability indices that can be used for the purpose of
redesigning the R/C elements of the building and in which they could
assist in considering some other remedial actions to improve the
safety and functionality of the member.
Abstract: Innovations not only contribute to competitiveness of
the company but have also positive effects on revenues. On average,
product innovations account to 14 percent of companies’ sales.
Innovation management has substantially changed during the last
decade, because of growing reliance on external partners. As a
consequence, a new task for purchasing arises, as firms need to
understand which suppliers actually do have high potential
contributing to the innovativeness of the firm and which do not.
Proper organization of the purchasing function is important since
for the majority of manufacturing companies deal with substantial
material costs which pass through the purchasing function. In the past
the purchasing function was largely seen as a transaction-oriented,
clerical function but today purchasing is the intermediate with supply
chain partners contributing to innovations, be it product or process
innovations. Therefore, purchasing function has to be organized
differently to enable firm innovation potential.
However, innovations are inherently risky. There are behavioral
risk (that some partner will take advantage of the other party),
technological risk in terms of complexity of products and processes
of manufacturing and incoming materials and finally market risks,
which in fact judge the value of the innovation. These risks are
investigated in this work. Specifically, technological risks which deal
with complexity of the products, and processes will be investigated
more thoroughly. Buying components or such high edge technologies
necessities careful investigation of technical features and therefore is
usually conducted by a team of experts. Therefore it is hypothesized
that higher the technological risk, higher will be the centralization of
the purchasing function as an interface with other supply chain
members.
Main contribution of this research lies is in the fact that analysis
was performed on a large data set of 1493 companies, from 25
countries collected in the GMRG 4 survey. Most analyses of
purchasing function are done by case study analysis of innovative
firms. Therefore this study contributes with empirical evaluations that
can be generalized.
Abstract: This paper is concerning the issues of behaviour of
lightweight expanded clay aggregates concrete exposed to high
temperature. Lightweight aggregates from expanded clay are
produced by firing of row material up to temperature 1050°C.
Lightweight aggregates have suitable properties in terms of volume
stability, when exposed to temperatures up to 1050°C, which could
indicate their suitability for construction applications with higher risk
of fire. The test samples were exposed to heat by using the standard
temperature-time curve ISO 834. Negative changes in resulting
mechanical properties, such as compressive strength, tensile strength,
and flexural strength were evaluated. Also visual evaluation of the
specimen was performed. On specimen exposed to excessive heat, an
explosive spalling could be observed, due to evaporation of
considerable amount of unbounded water from the inner structure of
the concrete.
Abstract: Characterization of the engineering behavior of
unsaturated soil is dependent on the soil-water characteristic curve
(SWCC), a graphical representation of the relationship between water
content or degree of saturation and soil suction. A reasonable
description of the SWCC is thus important for the accurate prediction
of unsaturated soil parameters. The measurement procedures for
determining the SWCC, however, are difficult, expensive, and timeconsuming.
During the past few decades, researchers have laid a
major focus on developing empirical equations for predicting the
SWCC, with a large number of empirical models suggested. One of
the most crucial questions is how precisely existing equations can
represent the SWCC. As different models have different ranges of
capability, it is essential to evaluate the precision of the SWCC
models used for each particular soil type for better SWCC estimation.
It is expected that better estimation of SWCC would be achieved via
a thorough statistical analysis of its distribution within a particular
soil class. With this in view, a statistical analysis was conducted in
order to evaluate the reliability of the SWCC prediction models
against laboratory measurement. Optimization techniques were used
to obtain the best-fit of the model parameters in four forms of SWCC
equation, using laboratory data for relatively coarse-textured (i.e.,
sandy) soil. The four most prominent SWCCs were evaluated and
computed for each sample. The result shows that the Brooks and
Corey model is the most consistent in describing the SWCC for sand
soil type. The Brooks and Corey model prediction also exhibit
compatibility with samples ranging from low to high soil water
content in which subjected to the samples that evaluated in this study.
Abstract: Immunomodulators are substances that alter immune
system via dynamic regulation of messenger molecules. It can be
divided into immunostimulant and immunosuppressant. It can help to
increase immunity of people with a low immune system, and also can
help to normalize an overactive immune system. Aim of this study is
to investigate the effects of in vitro exposure to low and high doses of
several immunomodulators which include caffeine, kaloba and
quercetin on antigen-stimulated whole blood culture cytokine
production. Whole blood samples were taken from 5 healthy males
(age: 32 ± 12 years; weight: 75.7 ± 6.1 kg; BMI: 24.3 ± 1.5 kg/m2)
following an overnight fast with no vigorous activity during the
preceding 24 h. The whole blood was then stimulated with 50 μl of
100 x diluted Pediacel vaccine and low or high dose of
immunomodulators in the culture plate. After 20 h incubation (5%
CO2, 37°C), it was analysed using the Evidence Investigator to
determine the production of cytokines including IL-2, IL-4, IL-10,
IFN-γ, and IL-1α. Caffeine and quercetin showed a tendency towards
decrease cytokine production as the doses were increased. On the
other hand, an upward trend was evident with kaloba, where a high
dose of kaloba seemed to increase the cytokine production. In
conclusion, we found that caffeine and quercetin have potential as
immunosuppressant and kaloba as immunostimulant.
Abstract: In this paper, we present a comparative assessment of
Space Vector Pulse Width Modulation (SVPWM) and Model
Predictive Control (MPC) for two-level three phase (2L-3P) Voltage
Source Inverter (VSI). VSI with associated system is subjected to
both control techniques and the results are compared.
Matlab/Simulink was used to model, simulate and validate the
control schemes. Findings of this study show that MPC is superior to
SVPWM in terms of total harmonic distortion (THD) and
implementation.