Abstract: Broiler slaughter waste has become a major source of
pollution throughout the world. Utilization of broiler slaughter waste
by dry rendering process produced Rendered Chicken Oil (RCO), a
cheap raw material for biodiesel production and Carcass Meal a feed
ingredient for pets and fishes. Conversion of RCO into biodiesel may
open new vistas for generating wealth from waste besides controlling
the major havoc of environmental pollution. A two-step process to
convert RCO to good quality Biodiesel was invented. Acid catalysed
esterification of FFA followed by base catalysed transesterification of
triglycerides was carried out after meticulously standardizing the
methanol molar ratio, catalyst concentration, reaction temperature,
and reaction time to obtain the maximum biodiesel yield of 97.62%
and lowest glycerol yield of 6.96%. RCO biodiesel blend was tested
in a CRDI diesel engine. The results revealed that the blending of
commercial diesel with 20% RCO biodiesel (B20) lead to less engine
wear, a quieter engine and better fuel economy. The better lubricating
qualities of RCO B20 prevented over heating of engine, which
prolongs the engine life. RCO B20 can reduce the import of crude oil
and substantially reduce the engine emissions as proved by
significantly lower smoke levels, thus mitigating climatic changes.
Abstract: The main cause of Alzheimer disease (AD) was
believed to be mainly due to the accumulation of free radicals owing
to oxidative stress (OS) in brain tissue. The mechanism of the
neurotoxicity of Aluminum chloride (AlCl3) induced AD in
hippocampus Albino wister rat brain tissue, the curative & the
protective effects of Lipidium sativum group (LS) water extract were
assessed after 8 weeks by attenuated total reflection spectroscopy
ATR-IR and histologically by light microscope. ATR-IR results
revealed that the membrane phospholipid undergo free radical
attacks, mediated by AlCl3, primary affects the polyunsaturated fatty
acids indicated by the increased of the olefinic -C=CH sub-band area
around 3012 cm-1 from the curve fitting analysis. The narrowing in
the half band width (HBW) of the sνCH2 sub-band around 2852 cm-1
due to Al intoxication indicates the presence of trans form fatty acids
rather than gauch rotomer. The degradation of hydrocarbon chain to
shorter chain length, increasing in membrane fluidity, disorder, and
decreasing in lipid polarity in AlCl3 group indicated by the detected
changes in certain calculated area ratios compared to the control.
Administration of LS was greatly improved these parameters
compared to the AlCl3 group. Al influences the Aβ aggregation and
plaque formation, which in turn interferes to and disrupts the
membrane structure. The results also showed a marked increase in
the β-parallel and antiparallel structure, that characterize the Aβ
formation in Al-induced AD hippocampal brain tissue, indicated by
the detected increase in both amide I sub-bands around 1674, 1692
cm-1. This drastic increase in Aβ formation was greatly reduced in the
curative and protective groups compared to the AlCl3 group and
approached nearly the control values. These results supported too by
the light microscope. AlCl3 group showed significant marked
degenerative changes in hippocampal neurons. Most cells appeared
small, shrieked and deformed. Interestingly, the administration of LS
in curative and protective groups markedly decreases the amount of
degenerated cells compared to the non-treated group. In addition, the
intensity of congo red stained cells was decreased. Hippocampal
neurons looked more/or less similar to those of control. This study showed a promising therapeutic effect of Lipidium
sativum group (LS) on AD rat model that seriously overcome the
signs of oxidative stress on membrane lipid and restore the protein
misfolding.
Abstract: Highly developed technology and highly competitive
global market highlight the important role of competitive advantages
and operation performances in sustainable company operation.
Activity-Based Costing (ABC) provides accurate operation cost and
operation performance information. Rich literatures provide relevant
research with cases study on Activity-Based Costing application, but
the research on cause relationship between key success factors and its
specific outcome, such as profitability or share market are few. These
relationships provide the ways to handle the key success factors to
achieve the specific outcomes for ensuring to promote the competitive
advantages and operation performances. The main purposes of this
research are exploring the key success paths by Key Success Paths
approach which will lead the ways to apply Activity-Base Costing.
The Key Success Paths is the innovative method which is exploring
the cause relationships and explaining what are the effects of key
success factors to specific outcomes of Activity-Based Costing
implementation. The cause relationships between key success factors
and successful specific outcomes are Key Success Paths (KSPs). KSPs
are the guidelines to lead the cost management strategies to achieve the
goals of competitive advantages and operation performances. The
research findings indicate that good management system design may
affect the well outcomes of Activity-Based Costing application and
achieve to outstanding competitive advantage, operating performance
and profitability as well by KSPs exploration.
Abstract: This paper is concerned with the ways in which
Assisted Reproductive Technologies (ARTs) affect women’s lives
and perceptions regarding their infertility, contraception and
reproductive health. The paper is based on a qualitative feminist
survey study to explore and analyze issues arising from the use of
ARTs by women in New Delhi, the capital of India. A rapid growth in
the number of fertility clinics has been noticed recently. A critical
analysis of interviews revealed that these technologies are used and
developed for making profits at the cost of women’s lives. In this
way, these technologies are influencing and changing the traditional
patterns of motherhood requiring a rethinking about new ways of
reproduction introduced through the use of ARTs.
Abstract: Various nanomaterials can be used as a drug delivery
vehicles in nanomedicine, called nanocarriers. They can either be
organic or inorganic, synthetic or natural-based. Although synthetic
nanocarriers are easier to produce, they can often be toxic for the
organism and thus not suitable for use in treatment. From naturalbased
nanocarriers, the most commonly used are protein cages or
viral capsids. In this work, virus bacteriophage λ was used for
delivery of different cytotoxic drugs (cisplatin, carboplatin,
oxaliplatin and doxorubicin). Large quantities of phage λ were
obtained from phage λ-producing strain of E. coli cultivated in
medium with 0.2% maltose. After killing of E. coli with chloroform
and its removal by centrifugation, the phage was concentrated by
ultracentrifugation at 130 000×g and 4°C for 3 h. The encapsulation
of the drugs was performed by infusion method and four different
concentrations of the drugs were encapsulated (200; 100; 50; 25
μg·mL-1). Free drug molecules were removed by filtration. The
encapsulation was verified using the absorbance for doxorubicin and
atomic absorption spectrometry for platinum cytostatics. The amount
of encapsulated drug linearly increased with the increasing
concentration of applied drug with the determination coefficient
R2=0.989 for doxorubicin; R2=0.967 for cisplatin; R2=0.989 for
carboplatin and R2=0.996 for oxaliplatin. The overall encapsulation
efficiency was calculated as 50% for doxorubicin; 8% for cisplatin;
6% for carboplatin and 10% for oxaliplatin.
Abstract: Chatter vibrations, occurring during cutting process,
cause vibration between the cutting tool and workpiece, which
deteriorates surface roughness and reduces tool life. The purpose of
this study is to investigate the influence of cutting parameters and
tool construction on surface roughness and vibration in turning of
aluminum alloy AA2024. A new design of cutting tool is proposed,
which is filled up with epoxy granite in order to improve damping
capacity of the tool. Experiments were performed at the lathe using
carbide cutting insert coated with TiC and two different cutting tools
made of AISI 5140 steel. Taguchi L9 orthogonal array was applied to
design of experiment and to optimize cutting conditions. By the help
of signal-to-noise ratio and analysis of variance the optimal cutting
condition and the effect of the cutting parameters on surface
roughness and vibration were determined. Effectiveness of Taguchi
method was verified by confirmation test. It was revealed that new
cutting tool with epoxy granite has reduced vibration and surface
roughness due to high damping properties of epoxy granite in
toolholder.
Abstract: Noninvasive diagnostics of diseases via breath
analysis has attracted considerable scientific and clinical interest for
many years and become more and more promising with the rapid
advancements in nanotechnology and biotechnology. The volatile
organic compounds (VOCs) in exhaled breath, which are mainly
blood borne, particularly provide highly valuable information about
individuals’ physiological and pathophysiological conditions.
Additionally, breath analysis is noninvasive, real-time, painless, and
agreeable to patients. We have developed a wireless sensor array
based on single-stranded DNA (ssDNA)-functionalized single-walled
carbon nanotubes (SWNT) for the detection of a number of
physiological indicators in breath. Seven DNA sequences were used
to functionalize SWNT sensors to detect trace amount of methanol,
benzene, dimethyl sulfide, hydrogen sulfide, acetone, and ethanol,
which are indicators of heavy smoking, excessive drinking, and
diseases such as lung cancer, breast cancer, and diabetes. Our test
results indicated that DNA functionalized SWNT sensors exhibit
great selectivity, sensitivity, and repeatability; and different
molecules can be distinguished through pattern recognition enabled
by this sensor array. Furthermore, the experimental sensing results
are consistent with the Molecular Dynamics simulated ssDNAmolecular
target interaction rankings. Thus, the DNA-SWNT sensor
array has great potential to be applied in chemical or biomolecular
detection for the noninvasive diagnostics of diseases and personal
health monitoring.
Abstract: High Performance Liquid Chromatography (HPLC)
method was developed and validated for simultaneous estimation of
6-Gingerol(6G) and 6-Shogaol(6S) in joint pain relief gel containing
ginger extract. The chromatographic separation was achieved by
using C18 column, 150 x 4.6mm i.d., 5μ Luna, mobile phase
containing acetonitrile and water (gradient elution). The flow rate
was 1.0 ml/min and the absorbance was monitored at 282 nm. The
proposed method was validated in terms of the analytical parameters
such as specificity, accuracy, precision, linearity, range, limit of
detection (LOD), limit of quantification (LOQ), and determined
based on the International Conference on Harmonization (ICH)
guidelines. The linearity ranges of 6G and 6S were obtained over 20-
60 and 6-18 μg/ml respectively. Good linearity was observed over the
above-mentioned range with linear regression equation Y= 11016x-
23778 for 6G and Y = 19276x-19604 for 6S (x is concentration of
analytes in μg/ml and Y is peak area). The value of correlation
coefficient was found to be 0.9994 for both markers. The limit of
detection (LOD) and limit of quantification (LOQ) for 6G were
0.8567 and 2.8555 μg/ml and for 6S were 0.3672 and 1.2238 μg/ml
respectively. The recovery range for 6G and 6S were found to be
91.57 to 102.36 % and 84.73 to 92.85 % for all three spiked levels.
The RSD values from repeated extractions for 6G and 6S were 3.43
and 3.09% respectively. The validation of developed method on
precision, accuracy, specificity, linearity, and range were also
performed with well-accepted results.
Abstract: The effects of the contact ball-lens on the soda lime
glass in laser thermal cleavage with a cw Nd-YAG laser were
investigated in this study. A contact ball-lens was adopted to generate
a bending force on the crack formation of the soda-lime glass in the
laser cutting process. The Nd-YAG laser beam (wavelength of 1064
nm) was focused through the ball-lens and transmitted to the soda-lime
glass, which was coated with a carbon film on the surface with a
bending force from a ball-lens to generate a tensile stress state on the
surface cracking. The fracture was controlled by the contact ball-lens
and a straight cutting was tested to demonstrate the feasibility.
Experimental observations on the crack propagation from the leading
edge, main section and trailing edge of the glass sheet were compared
with various mechanical and thermal loadings. Further analyses on the
stress under various laser powers and contact ball loadings were made
to characterize the innovative technology. The results show that the distributions of the side crack at the
leading and trailing edges are mainly dependent on the boundary
condition, contact force, cutting speed and laser power. With the
increase of the mechanical and thermal loadings, the region of the side
cracks might be dramatically reduced with proper selection of the
geometrical constrains. Therefore the application of the contact
ball-lens is a possible way to control the fracture in laser cleavage with
improved cutting qualities.
Abstract: The plastic industry plays very important role in the
economy of any country. It is generally among the leading share of
the economy of the country. Since metals and their alloys are very
rarely available on the earth. Therefore, to produce plastic products
and components, which finds application in many industrial as well
as household consumer products is beneficial. Since 50% plastic
products are manufactured by injection moulding process. For
production of better quality product, we have to control quality
characteristics and performance of the product. The process
parameters plays a significant role in production of plastic, hence the
control of process parameter is essential. In this paper the effect of
the parameters selection on injection moulding process has been
described. It is to define suitable parameters in producing plastic
product. Selecting the process parameter by trial and error is neither
desirable nor acceptable, as it is often tends to increase the cost and
time. Hence, optimization of processing parameter of injection
moulding process is essential. The experiments were designed with
Taguchi’s orthogonal array to achieve the result with least number of
experiments. Plastic material polypropylene is studied. Tensile
strength test of material is done on universal testing machine, which
is produced by injection moulding machine. By using Taguchi
technique with the help of MiniTab-14 software the best value of
injection pressure, melt temperature, packing pressure and packing
time is obtained. We found that process parameter packing pressure
contribute more in production of good tensile plastic product.
Abstract: The increase of technogenic and natural accidents,
accompanied by air pollution, for example, by combustion products,
leads to the necessity of respiratory protection. This work is devoted to the development of a calorimetric method
and a device which allows investigating quickly the kinetics of
carbon dioxide sorption by chemisorbents on the base of potassium
superoxide in order to assess the protective properties of respiratory
protective closed circuit apparatus. The features of the traditional approach for determining the
sorption properties in a thin layer of chemisorbent are described, as
well as methods and devices, which can be used for the sorption
kinetics study. The authors developed an approach (as opposed to the traditional
approach) based on the power measurement of internal heat sources
in the chemisorbent layer. The emergence of the heat sources is a
result of exothermic reaction of carbon dioxide sorption. This
approach eliminates the necessity of chemical analysis of samples
and can significantly reduce the time and material expenses during
chemisorbents testing. Error of determining the volume fraction of adsorbed carbon
dioxide by the developed method does not exceed 12%. Taking into
account the efficiency of the method, we consider that it is a good
alternative to traditional methods of chemical analysis under the
assessment of the protection sorbents quality.
Abstract: In Algeria, the most impressive and most known
prehistoric art is the painted or engraved rock art which is present
with abundance in several regions. The existence of rock art in Great
Kabylia region has been known for over sixty years. The main purpose of this research is to show the dangers facing
these rock paintings and engravings and what are the arrangements
for their protection and recovery. As every vestige destroyed is a part of the world's memory which
disappears, some steps have to be taken in order to protect these
historical and archaeological heritages.
Abstract: The aim of sustainable architecture is to design
buildings with the least adverse effects on the environment and
provide better conditions for people. What building forms make the
best use of land? This question was addressed in the late 1960s at the
center of Land Use and Built Form Studies in Cambridge. This led to
a number of influential papers which had a great influence on the
practice of urban design. This paper concentrates on the results of
sustainability caused by climatic conditions in Iranian traditional
architecture in hot-arid regions. As people spent a significant amount
of their time in houses, it was very important to have such houses to
fulfill their needs physically and spiritually as well as satisfying their
cultural and religious aspects of their lifestyles. In a vast country such
as Iran with different climatic zones, traditional builders have
presented series of logical solutions for human comfort. These
solutions have been able to response to the environmental problems
for a long period of time. As a result, by considering the experience
in traditional architecture of hot–arid climate in Iran, it is possible to
attain sustainable architecture.
Abstract: The paper will focus on the strategic development
deriving from the evolution of the traditional courtyard spatial
organization towards a new, contemporary sustainable way of living.
New sustainable approaches that engulf the social issues, the notion
of place, the understanding of weather architecture blended together
with the bioclimatic behavior will be seen through a series of
experimental case studies in the island of Cyprus, inspired and
originated from its traditional wisdom, ranging from small scale of
living to urban interventions. Weather and nature will be seen as co-architectural authors with
architects. Furthermore, the building will be seen not as an object but
rather as a vessel of human activities. This will further enhance the
notion of merging the material and immaterial, the built and unbuilt,
subject-human, and the object-building. This eventually will enable
to generate the discussion of the understanding of the building in
relation to the place and its inhabitants, where the human topography
is more important than the material topography. The specificities of
the divided island and the dealing with sites that are in vicinity with
the diving Green Line will further trigger explorations dealing with
the regeneration issues and the social sustainability offering
unprecedented opportunities for innovative sustainable ways of
living. Opening up a discourse with premises of weather-nature, materialimmaterial,
human-material topographies in relation to the contested
sites of the borders will lead us to develop innovative strategies for a
profound, both technical and social sustainability, which fruitfully
yields to innovative living built environments, responding to the ever
changing environmental and social needs. As a starting point, a case study in Kaimakli in Nicosia, a
refurbishment with an extension of a traditional house, already
engulfs all the traditional/ vernacular wisdom of the bioclimatic
architecture. The project focusses on the direct and quite obvious
bioclimatic features such as south orientation and cross ventilation.
Furthermore, it tries to reinvent the adaptation of these parameters in
order to turn the whole house to a contemporary living environment.
In order to succeed this, evolutions of traditional architectural
elements and spatial conditions are integrated in a way that does not
only respond to some certain weather conditions, but they integrate
and blend the weather within the built environment. A series of
innovations aiming at maximum flexibility is proposed. The house
can finally be transformed into a winter enclosure, while for the most
part of the year it turns into a ‘camping’ living environment. Parallel to experimental interventions in existing traditional units,
we will proceed examining the implementation of the same
developed methodology in designing living units and complexes.
Malleable courtyard organizations that attempt to blend the
traditional wisdom with the contemporary needs for living, the
weather and nature with the built environment will be seen tested in
both horizontal and vertical developments. Social activities are seen as directly affected and forged by the
weather conditions thus generating a new social identity of people where people are directly involved and interacting with the weather.
The human actions and interaction with the built, material
environment in order to respond to weather will be seen as the result
of balancing the social with the technological sustainability, the
immaterial, and the material aspects of the living environment.
Abstract: A solar receiver is designed for operation under
extremely uneven heat flux distribution, cyclic weather, and cloud
transient cycle conditions, which can include large thermal stress and
even receiver failure. In this study, the effect of different oil velocity
on convection coefficient factor and impact of wind velocity on local
Nusselt number by Finite Volume Method will be analyzed. This
study is organized to give an overview of the numerical modeling
using a MATLAB software, as an accurate, time efficient and
economical way of analyzing the heat transfer trends over stationary
receiver tube for different Reynolds number. The results reveal when
oil velocity is below 0.33m/s, the value of convection coefficient is
negligible at low temperature. The numerical graphs indicate that
when oil velocity increases up to 1.2 m/s, heat convection coefficient
increases significantly. In fact, a reduction in oil velocity causes a
reduction in heat conduction through the glass envelope. In addition,
the different local Nusselt number is reduced when the wind blows
toward the concave side of the collector and it has a significant effect
on heat losses reduction through the glass envelope.
Abstract: A geoelectric survey was carried out in some parts of
Angwan Gwari, an outskirt of Lapai Local Government Area on
Niger State which belongs to the Nigerian Basement Complex, with
the aim of evaluating the soil corrosivity, aquifer transmissivity and
protective capacity of the area from which aquifer characterisation
was made. The G41 Resistivity Meter was employed to obtain fifteen
Schlumberger Vertical Electrical Sounding data along profiles in a
square grid network. The data were processed using interpex 1-D
sounding inversion software, which gives vertical electrical sounding
curves with layered model comprising of the apparent resistivities,
overburden thicknesses, and depth. This information was used to
evaluate longitudinal conductance and transmissivities of the layers.
The results show generally low resistivities across the survey area
and an average longitudinal conductance variation from
0.0237Siemens in VES 6 to 0.1261Siemens in VES 15 with almost
the entire area giving values less than 1.0 Siemens. The average
transmissivity values range from 96.45 Ω.m2 in VES 4 to 299070
Ω.m2 in VES 1. All but VES 4 and VES14 had an average
overburden greater than 400 Ω.m2, these results suggest that the
aquifers are highly permeable to fluid movement within, leading to
the possibility of enhanced migration and circulation of contaminants
in the groundwater system and that the area is generally corrosive.
Abstract: Experience is what makes a man perfect. Though we
tend to learn many a different things in life through practice still we
need to go an extra mile to gain experience which would be profitable
only when it is integrated with regular practice. A clear phenomenal
idea is that every teacher is a learner. The centralized idea of this paper would focus on the integrated
practices carried out among the students of Jizan University which
enhances learning through experiences. Integrated practices like
student-directed activities, balanced curriculum, phonological based
activities and use of consistent language would enlarge the vision and
mission of students to earn experience through learning. Students
who receive explicit instruction and guidance could practice the skills
and strategies through student-directed activities such as peer tutoring
and cooperative learning. The second effective practice is to use
consistent language. Consistent language provides students a model
for talking about the new concepts which also enables them to
communicate without hindrances. Phonological awareness is an
important early reading skill for all students. Students generally have
phonemic awareness in their home language can often transfer that
knowledge to a second language. And also a balanced curriculum
requires instruction in all the elements of reading. Reading is the
most effective skill when both basic and higher-order skills are
included on a daily basis. Computer based reading and listening skills
will empower students to understand language in a better way.
English language learners can benefit from sound reading instruction
even before they are fully proficient in English as long as the
instruction is comprehensible. Thus, if students have to be well
equipped in learning they should foreground themselves in various
integrated practices through multifarious experience for which
teachers are moderators and trainers. This type of learning prepares
the students for a constantly changing society which helps them to
meet the competitive world around them for better employability
fulfilling the vision and mission of the institution.
Abstract: Magnetic Resonance Imaging (MRI) is one of the
most important medical imaging modality. Subjective assessment of
the image quality is regarded as the gold standard to evaluate MR
images. In this study, a database of 210 MR images which contains
ten reference images and 200 distorted images is presented. The
reference images were distorted with four types of distortions: Rician
Noise, Gaussian White Noise, Gaussian Blur and DCT compression.
The 210 images were assessed by ten subjects. The subjective scores
were presented in Difference Mean Opinion Score (DMOS). The
DMOS values were compared with four FR-IQA metrics. We have
used Pearson Linear Coefficient (PLCC) and Spearman Rank Order
Correlation Coefficient (SROCC) to validate the DMOS values. The
high correlation values of PLCC and SROCC shows that the DMOS
values are close to the objective FR-IQA metrics.
Abstract: Electrical Muscle Stimulation (EMS) has been
introduced and globally gained increasing attention on its usefulness.
Continuous application of EMS may lead to the increment of muscle
mass and indirectly will increase the strength. This study can be used
as an alternative to help people especially those living a sedentary
lifestyle to improve their muscle activity without having to go
through a heavy workout session. Therefore, this study intended to
investigate the effectiveness of EMS training program in 5 weeks
interventions towards male body composition. It was a quasiexperimental
design, held at the Impulse Studio Bangsar, which
examined the effects of EMS training towards skeletal muscle mass
among the subjects. Fifteen subjects (n = 15) were selected to assist
in this study. The demographic data showed that, the average age of
the subjects was 43.07 years old ± 9.90, height (173.4 cm ± 9.09) and
weight was (85.79 kg ± 18.07). Results showed that there was a
significant difference on the skeletal muscle mass (p = 0.01 < 0.05),
upper body (p = 0.01 < 0.05) and lower body (p = 0.00 < 0.05).
Therefore, the null hypothesis has been rejected in this study. As a
conclusion, the application of EMS towards body composition can
increase the muscle size and strength. This method has been proven
to be able to improve athlete strength and thus, may be implemented
in the sports science area of knowledge.
Abstract: This article proposes a hybrid algorithm for spectrum
allocation in cognitive radio networks based on the algorithms
Analytical Hierarchical Process (AHP) and Technique for Order of
Preference by Similarity to Ideal Solution (TOPSIS) to improve the
performance of the spectrum mobility of secondary users in cognitive
radio networks. To calculate the level of performance of the proposed algorithm a
comparative analysis between the proposed AHP-TOPSIS, Grey
Relational Analysis (GRA) and Multiplicative Exponent Weighting
(MEW) algorithm is performed. Four evaluation metrics are used.
These metrics are accumulative average of failed handoffs,
accumulative average of handoffs performed, accumulative average
of transmission bandwidth, and accumulative average of the
transmission delay. The results of the comparison show that AHP-TOPSIS Algorithm
provides 2.4 times better performance compared to a GRA Algorithm
and, 1.5 times better than the MEW Algorithm.