Abstract: Undoubtedly, chassis is one of the most important
parts of a vehicle. Chassis that today are produced for vehicles are
made up of four parts. These parts are jointed together by screwing.
Transverse parts are called cross member.
This study reviews the stress generated by cyclic laboratory loads
in front cross member of Peugeot 405. In this paper the finite element
method is used to simulate the welding process and to determine the
physical response of the spot-welded joints. Analysis is done by the
Abaqus software.
The Stresses generated in cross member structure are generally
classified into two groups: The stresses remained in form of residual
stresses after welding process and the mechanical stress generated by
cyclic load. Accordingly the total stress must be obtained by
determining residual stress and mechanical stress separately and then
sum them according to the superposition principle.
In order to improve accuracy, material properties including
physical, thermal and mechanical properties were supposed to be
temperature-dependent. Simulation shows that maximum Von Misses
stresses are located at special points. The model results are then
compared to the experimental results which are reported by
producing factory and good agreement is observed.
Abstract: The fundamental defect inherent to the thermoforming
technology is wall-thickness variation of the products due to
inadequate thermal processing during production of polymer. A
nonlinear viscoelastic rheological model is implemented for
developing the process model. This model describes deformation
process of a sheet in thermoforming process. Because of relaxation
pause after plug-assist stage and also implementation of two stage
thermoforming process have minor wall-thickness variation and
consequently better mechanical properties of polymeric articles. For
model validation, a comparative analysis of the theoretical and
experimental data is presented.
Abstract: Bone remodeling occurs by the balanced action of
bone resorbing osteoclasts (OC) and bone-building osteoblasts.
Increased bone resorption by excessive OC activity contributes
to malignant and non-malignant diseases including osteoporosis.
To study OC differentiation and function, OC formed in
in vitro cultures are currently counted manually, a tedious
procedure which is prone to inter-observer differences. Aiming
for an automated OC-quantification system, classification of
OC and precursor cells was done on fluorescence microscope
images based on the distinct appearance of fluorescent nuclei.
Following ellipse fitting to nuclei, a combination of eight
features enabled clustering of OC and precursor cell nuclei.
After evaluating different machine-learning techniques, LOGREG
achieved 74% correctly classified OC and precursor cell
nuclei, outperforming human experts (best expert: 55%). In
combination with the automated detection of total cell areas,
this system allows to measure various cell parameters and most
importantly to quantify proteins involved in osteoclastogenesis.
Abstract: A satellite is being integrated and tested by BISEE (Beijing Institute of Spacecraft Environment Engineering). This paper describes the infrared lamp array simulation technology used for satellite thermal balance and thermal vacuum test. These tests were performed in KM6 space environmental simulator in Beijing, China. New software and hardware developed by BISEE, along with enhanced heat flux uniformity, provided for well accomplished thermal balance and thermal vacuum tests. The flux uniformity of lamp array was satisfied with test requirement. Monitored background radiometer offered reliable heat flux measurements with remarkable repeatability. Simulation software supplied accurate thermal flux distribution predictions.
Abstract: The present paper proposes high performance nonlinear
force controllers for a servopneumatic real-time fatigue test
machine. A CompactRIO® controller was used, being fully
programmed using LabVIEW language. Fuzzy logic control
algorithms were evaluated to tune the integral and derivative
components in the development of hybrid controllers, namely a FLC
P and a hybrid FLC PID real-time-based controllers. Their
behaviours were described by using state diagrams. The main
contribution is to ensure a smooth transition between control states,
avoiding discrete transitions in controller outputs. Steady-state errors
lower than 1.5 N were reached, without retuning the controllers.
Good results were also obtained for sinusoidal tracking tasks from
1/¤Ç to 8/¤Ç Hz.
Abstract: Actual load, material characteristics and other
quantities often differ from the design values. This can cause worse
function, shorter life or failure of a civil engineering structure, a
machine, vehicle or another appliance. The paper shows main causes
of the uncertainties and deviations and presents a systematic
approach and efficient tools for their elimination or mitigation of
consequences. Emphasis is put on the design stage, which is most
important for reliability ensuring. Principles of robust design and
important tools are explained, including FMEA, sensitivity analysis
and probabilistic simulation methods. The lifetime prediction of
long-life objects can be improved by long-term monitoring of the
load response and damage accumulation in operation. The condition
evaluation of engineering structures, such as bridges, is often based
on visual inspection and verbal description. Here, methods based on
fuzzy logic can reduce the subjective influences.
Abstract: Artificial Neural Network (ANN) has been
extensively used for classification of heart sounds for its
discriminative training ability and easy implementation. However, it
suffers from overparameterization if the number of nodes is not
chosen properly. In such cases, when the dataset has redundancy
within it, ANN is trained along with this redundant information that
results in poor validation. Also a larger network means more
computational expense resulting more hardware and time related
cost. Therefore, an optimum design of neural network is needed
towards real-time detection of pathological patterns, if any from heart
sound signal. The aims of this work are to (i) select a set of input
features that are effective for identification of heart sound signals and
(ii) make certain optimum selection of nodes in the hidden layer for a
more effective ANN structure. Here, we present an optimization
technique that involves Singular Value Decomposition (SVD) and
QR factorization with column pivoting (QRcp) methodology to
optimize empirically chosen over-parameterized ANN structure.
Input nodes present in ANN structure is optimized by SVD followed
by QRcp while only SVD is required to prune undesirable hidden
nodes. The result is presented for classifying 12 common
pathological cases and normal heart sound.
Abstract: The conceptually construction of axially chiral indolostilbenesi.eN-(2-{(E)-2-[2'-(1-Acetyl-1H-indol-2-yl)-3'chloro-4,4',6,6'-tetramethoxy[1,1'-biphenyl]-2yl]ethenyl}phenyl)acetamide and N-(2-{(E)-2-[2'-(1-Acetyl-1H-indol-2-yl)-3'-chloro-2,4',6,6'-tetramethoxy[1,1'-biphenyl]-4-yl]ethenyl}phenyl) acetamide are described in this paper. These structure, were obtained by the tactical combination of palladium-catalyzed coupling which produced 10-acetamido-3,5-dimethoxystilbene, follow by FeCl3-induced oxidative cyclization/dimerisation. All structures were unambiguously confirmed by 1D (1H, 13C) and 2D NMR experiment, (COSY, HMQC, HMBC) and mass spectrometry.
Abstract: This paper explores how Critical Systems Thinking and Action Research can be used to improve student performance in Networking. When describing a system from a systems thinking perspective, the following aspects can be identified: the total system performance, the systems environment, the resources, the components and the management of the system. Following the history of system thinking we observe three emerged methodologies namely, hard systems, soft systems, and critical systems. This paper uses Critical Systems Thinking (CST) which describes systems in terms of contradictions and conflict. It demonstrates how CST can be used in an Action Research (AR) project to improve the performance of students. Intervention in terms of student assessment is discussed and the impact of the intervention is discussed.
Abstract: In this paper we present an efficient system for
independent speaker speech recognition based on neural network
approach. The proposed architecture comprises two phases: a
preprocessing phase which consists in segmental normalization and
features extraction and a classification phase which uses neural
networks based on nonparametric density estimation namely the
general regression neural network (GRNN). The relative
performances of the proposed model are compared to the similar
recognition systems based on the Multilayer Perceptron (MLP), the
Recurrent Neural Network (RNN) and the well known Discrete
Hidden Markov Model (HMM-VQ) that we have achieved also.
Experimental results obtained with Arabic digits have shown that the
use of nonparametric density estimation with an appropriate
smoothing factor (spread) improves the generalization power of the
neural network. The word error rate (WER) is reduced significantly
over the baseline HMM method. GRNN computation is a successful
alternative to the other neural network and DHMM.
Abstract: In this study we tried to replicate the unconscious
thought advantage (UTA), which states that complex decisions are
better handled by unconscious thinking. We designed an experiment
in e-prime using similar material as the original study (choosing
between four different apartments, each described by 12 attributes).
A total of 73 participants (52 women (71.2%); 18 to 62 age:
M=24.63; SD=8.7) took part in the experiment. We did not replicate
the results suggested by UTT. However, from the present study we
cannot conclude whether this was the case of flaws in the theory or
flaws in our experiment and we discuss several ways in which the
issue of UTA could be examined further.
Abstract: In the last few years, three multivariate spectral
analysis techniques namely, Principal Component Analysis (PCA),
Independent Component Analysis (ICA) and Non-negative Matrix
Factorization (NMF) have emerged as effective tools for oscillation
detection and isolation. While the first method is used in determining
the number of oscillatory sources, the latter two methods
are used to identify source signatures by formulating the detection
problem as a source identification problem in the spectral domain.
In this paper, we present a critical drawback of the underlying linear
(mixing) model which strongly limits the ability of the associated
source separation methods to determine the number of sources
and/or identify the physical source signatures. It is shown that the
assumed mixing model is only valid if each unit of the process gives
equal weighting (all-pass filter) to all oscillatory components in its
inputs. This is in contrast to the fact that each unit, in general, acts
as a filter with non-uniform frequency response. Thus, the model
can only facilitate correct identification of a source with a single
frequency component, which is again unrealistic. To overcome
this deficiency, an iterative post-processing algorithm that correctly
identifies the physical source(s) is developed. An additional issue
with the existing methods is that they lack a procedure to pre-screen
non-oscillatory/noisy measurements which obscure the identification
of oscillatory sources. In this regard, a pre-screening procedure
is prescribed based on the notion of sparseness index to eliminate
the noisy and non-oscillatory measurements from the data set used
for analysis.
Abstract: Knowing the geometrical object pose of products in manufacturing line before robot manipulation is required and less time consuming for overall shape measurement. In order to perform it, the information of shape representation and matching of objects is become required. Objects are compared with its descriptor that conceptually subtracted from each other to form scalar metric. When the metric value is smaller, the object is considered closed to each other. Rotating the object from static pose in some direction introduce the change of value in scalar metric value of boundary information after feature extraction of related object. In this paper, a proposal method for indexing technique for retrieval of 3D geometrical models based on similarity between boundaries shapes in order to measure 3D CAD object pose using object shape feature matching for Computer Aided Testing (CAT) system in production line is proposed. In experimental results shows the effectiveness of proposed method.
Abstract: Capacity and efficiency of any refrigerating system
diminish rapidly as the difference between the evaporating and
condensing temperature is increased by a reduction in the evaporator
temperature. The single stage vapour compression refrigeration
system using various refrigerants are limited to an evaporator
temperature of -40 0C. Below temperature of -40 0C the either
cascade refrigeration system or multi stage vapour compression
system is employed. Present work describes thermal design of
condenser (HTS), cascade condenser and evaporator (LTS) of
R404A-R508B and R410A-R23 cascade refrigeration system. Heat
transfer area of condenser, cascade condenser and evaporator for
both systems are compared and the effect of condenser and
evaporator temperature on heat-transfer area for both systems is
studied under same operating condition. The results shows that the
required heat-transfer area of condenser and cascade condenser for
R410A-R23 cascade system is lower than the R404A-R508B cascade
system but heat transfer area of evaporator is similar for both the
system. The heat transfer area of condenser and cascade condenser
decreases with increase in condenser temperature (Tc), whereas the
heat transfer area of cascade condenser and evaporator increases with
increase in evaporator temperature (Te).
Abstract: Stuck-pipe in drilling operations is one of the most
pressing and expensive problems in the oil industry. This paper
describes a computational simulation and an experimental study of
the hydrodynamic vibrator, which may be used for liquidation of
stuck-pipe problems during well drilling. The work principle of the
vibrator is based upon the known phenomena of Vortex Street of
Karman and the resulting generation of vibrations. We will discuss
the computational simulation and experimental investigations of
vibrations in this device. The frequency of the vibration parameters
has been measured as a function of the wide range Reynolds Number.
The validity of the computational simulation and of the assumptions
on which it is based has been proved experimentally. The
computational simulation of the vibrator work and its effectiveness
was carried out using FLUENT software. The research showed high
degree of congruence with the results of the laboratory tests and
allowed to determine the effect of the granular material features upon
the pipe vibration in the well. This study demonstrates the potential
of using the hydrodynamic vibrator in a well drilling system.
Abstract: The existence of maximal durations drastically modifies the performance evaluation in Discrete Event Systems (DES). The same particularity may be found on systems where the associated constraints do not concern the time. For example weight measures, in chemical industry, are used in order to control the quantity of consumed raw materials. This parameter also takes a fundamental part in the product quality as the correct transformation process is based upon a given percentage of each essence. Weight regulation therefore increases the global productivity of the system by decreasing the quantity of rejected products. In this paper we present an approach based on mixing different characteristics theories, the fuzzy system and Petri net system to describe the behaviour. An industriel application on a tobacco manufacturing plant, where the critical parameter is the weight is presented as an illustration.
Abstract: The increasing influence of traffic on building
objects and people residing in them should be taken into account in
diagnosis and design. Users of buildings expect that vibrations
occurring in their environment, will not only lead to damage to the
building or its accelerated wear, but neither would affect the required
comfort in rooms designed to accommodate people. This article
describes the methods and principles useful in designing and building
diagnostics located near transportation routes, with particular
emphasis on the impact of traffic vibration on people in buildings. It
also describes the procedures used in obtaining information about the
parameters of vibrations in different cases of diagnostics and design.
A universal algorithm of procedure in diagnostics and design of
buildings taking into account assurance of human vibration comfort
of people residing in the these buildings was presented.
Abstract: In this paper we propose a novel approach for
searching eCommerce products using a mobile phone, illustrated by a
prototype eCoMobile. This approach aims to globalize the mobile
search by integrating the concept of user multilinguism into it. To
show that, we particularly deal with English and Arabic languages.
Indeed the mobile user can formulate his query on a commercial
product in either language (English/Arabic). The description of his
information need on commercial products relies on the ontology that
represents the conceptualization of the product catalogue knowledge
domain defined in both English and Arabic languages. A query
expressed on a mobile device client defines the concept that
corresponds to the name of the product followed by a set of pairs
(property, value) specifying the characteristics of the product. Once a
query is submitted it is then communicated to the server side which
analyses it and in its turn performs an http request to an eCommerce
application server (like Amazon). This latter responds by returning
an XML file representing a set of elements where each element
defines an item of the searched product with its specific
characteristics. The XML file is analyzed on the server side and then
items are displayed on the mobile device client along with its
relevant characteristics in the chosen language.
Abstract: Fair share objective has been included into the goaloriented
parallel computer job scheduling policy recently. However,
the previous work only presented the overall scheduling performance.
Thus, the per-user performance of the policy is still lacking. In this
work, the details of per-user fair share performance under the
Tradeoff-fs(Tx:avgX) policy will be further evaluated. A basic fair
share priority backfill policy namely RelShare(1d) is also studied.
The performance of all policies is collected using an event-driven
simulator with three real job traces as input. The experimental results
show that the high demand users are usually benefited under most
policies because their jobs are large or they have a lot of jobs. In the
large job case, one job executed may result in over-share during that
period. In the other case, the jobs may be backfilled for
performances. However, the users with a mixture of jobs may suffer
because if the smaller jobs are executing the priority of the remaining
jobs from the same user will be lower. Further analysis does not show
any significant impact of users with a lot of jobs or users with a large
runtime approximation error.
Abstract: The NGN (Next Generation Network), which can
provide advanced multimedia services over an all-IP based network, has been the subject of much attention for years. While there have
been tremendous efforts to develop its architecture and protocols, especially for IMS, which is a key technology of the NGN, it is far
from being widely deployed. However, efforts to create an advanced
signaling infrastructure realizing many requirements have resulted in a
large number of functional components and interactions between those
components. Thus, the carriers are trying to explore effective ways to
deploy IMS while offering value-added services. As one such
approach, we have proposed a self-organizing IMS. A self-organizing
IMS enables IMS functional components and corresponding physical
nodes to adapt dynamically and automatically based on situation such
as network load and available system resources while continuing IMS
operation. To realize this, service continuity for users is an important
requirement when a reconfiguration occurs during operation. In this
paper, we propose a mechanism that will provide service continuity to
users and focus on the implementation and describe performance
evaluation in terms of number of control signaling and processing time
during reconfiguration