Abstract: Within Rapid Prototyping technologies are used many
types of materials. Many of them are recyclable but there are still as
plastic like, so practically they do not degrade in the landfill.
Polylactic acid (PLA) is one of the special plastic materials, which
are biodegradable and available for 3D printing within Fused
Deposition Modeling (FDM) technology. The question is, if the
mechanical properties of produced models are comparable to similar
technical plastic materials which are usual for prototype production.
Presented paper shows the experiments results for tensile strength
measurements for specimens prepared with different 3D printer
settings and model orientation. Paper contains also the comparison of
tensile strength values with values measured on specimens produced
by conventional technologies as injection moulding.
Abstract: In this paper, the unstable angle of attack of a
FOXTROT aircraft is controlled by using Genetic Algorithm based
flight controller and the result is compared with the conventional
techniques like Tyreus-Luyben (TL), Ziegler-Nichols (ZN) and
Interpolation Rule (IR) for tuning the PID controller. In addition, the
performance indices like Mean Square Error (MSE), Integral Square
Error (ISE), and Integral Absolute Time Error (IATE) etc. are
improved by using Genetic Algorithm. It was established that the
error by using GA is very less as compared to the conventional
techniques thereby improving the performance indices of the
dynamic system.
Abstract: Wireless Sensor Network (WSN) routing is complex
due to its dynamic nature, computational overhead, limited battery
life, non-conventional addressing scheme, self-organization, and
sensor nodes limited transmission range. An energy efficient routing
protocol is a major concern in WSN. LEACH is a hierarchical WSN
routing protocol to increase network life. It performs self-organizing
and re-clustering functions for each round. This study proposes a
better sensor networks cluster head selection for efficient data
aggregation. The algorithm is based on Tabu search.
Abstract: In this paper, a novel Linear Feedback Shift Register
(LFSR) with Look Ahead Clock Gating (LACG) technique is
presented to reduce the power consumption in modern processors
and System-on-Chip. Clock gating is a predominant technique used
to reduce unwanted switching of clock signals. Several clock gating
techniques to reduce the dynamic power have been developed, of
which LACG is predominant. LACG computes the clock enabling
signals of each flip-flop (FF) one cycle ahead of time, based on the
present cycle data of the flip-flops on which it depends. It overcomes
the timing problems in the existing clock gating methods like datadriven
clock gating and Auto-Gated flip-flops (AGFF) by allotting a
full clock cycle for the determination of the clock enabling signals.
Further to reduce the power consumption in LACG technique, FFs
can be grouped so that they share a common clock enabling signal.
Simulation results show that the novel grouped LFSR with LACG
achieves 15.03% power savings than conventional LFSR with LACG
and 44.87% than data-driven clock gating.
Abstract: Hydraulic fracturing is one of the most important
stimulation techniques available to the petroleum engineer to extract
hydrocarbons in tight gas sandstones. It allows more oil and gas
production in tight reservoirs as compared to conventional means.
The main aim of the study is to optimize the hydraulic fracturing as
technique and for this purpose three multi-zones layer formation is
considered and fractured contemporaneously. The three zones are
named as Zone1 (upper zone), Zone2 (middle zone) and Zone3
(lower zone) respectively and they all occur in shale rock. Simulation was performed with Mfrac integrated software which
gives a variety of 3D fracture options. This simulation process
yielded an average fracture efficiency of 93.8%for the three
respective zones and an increase of the average permeability of the
rock system. An average fracture length of 909 ft with net height
(propped height) of 210 ft (average) was achieved. Optimum
fracturing results was also achieved with maximum fracture width of
0.379 inches at an injection rate of 13.01 bpm with 17995 Mscf of
gas production.
Abstract: Adequate and reliable estimates of aquifer parameters
are of utmost importance for proper management of vital
groundwater resources. At present scenario, the ground water is
polluted because of industrial waste disposed over the land and the
contaminants are transported in the aquifer from one area to another
area, which is depending on the characteristics of the aquifer and
contaminants. To know the contaminant transport, the accurate
estimation of aquifer properties is highly needed. Conventionally,
these properties are estimated through pumping tests carried out on
water wells. The occurrence and movement of ground water in the
aquifer are characteristically defined by the aquifer parameters. The
pumping (aquifer) test is the standard technique for estimating
various hydraulic properties of aquifer systems, viz., transmissivity
(T), hydraulic conductivity (K), storage coefficient (S) etc., for which
the graphical method is widely used. The study area for conducting
pumping test is Pydibheemavaram Industrial area near the coastal
belt of Srikulam, AP, India. The main objective of the present work is
to estimate the aquifer properties for developing contaminant
transport model for the study area.
Abstract: In this paper, we describe an application for face
recognition. Many studies have used local descriptors to characterize
a face, the performance of these local descriptors remain low by
global descriptors (working on the entire image). The application of
local descriptors (cutting image into blocks) must be able to store
both the advantages of global and local methods in the Discrete
Cosine Transform (DCT) domain. This system uses neural network
techniques. The letter method provides a good compromise between
the two approaches in terms of simplifying of calculation and
classifying performance. Finally, we compare our results with those
obtained from other local and global conventional approaches.
Abstract: Digital cameras to reduce cost, use an image sensor to
capture color images. Color Filter Array (CFA) in digital cameras
permits only one of the three primary (red-green-blue) colors to be
sensed in a pixel and interpolates the two missing components
through a method named demosaicking. Captured data is interpolated
into a full color image and compressed in applications. Color
interpolation before compression leads to data redundancy. This
paper proposes a new Vector Quantization (VQ) technique to
construct a VQ codebook with Differential Evolution (DE)
Algorithm. The new technique is compared to conventional Linde-
Buzo-Gray (LBG) method.
Abstract: Prediction of maximum local scour is necessary for
the safety and economical design of the bridges. A number of
equations have been developed over the years to predict local scour
depth using laboratory data and a few pier equations have also been
proposed using field data. Most of these equations are empirical in
nature as indicated by the past publications. In this paper attempts
have been made to compute local depth of scour around bridge pier in
dimensional and non-dimensional form by using linear regression,
simple regression and SVM (Poly & Rbf) techniques along with few
conventional empirical equations. The outcome of this study suggests
that the SVM (Poly & Rbf) based modeling can be employed as an
alternate to linear regression, simple regression and the conventional
empirical equations in predicting scour depth of bridge piers. The
results of present study on the basis of non-dimensional form of
bridge pier scour indicate the improvement in the performance of
SVM (Poly & Rbf) in comparison to dimensional form of scour.
Abstract: During machining process, chatter is an unavoidable
phenomenon. Boring bars possess the cantilever shape and due to
this, it is subjected to chatter. The adverse effect of chatter includes
the increase in temperature which will leads to excess tool wear. To
overcome these problems, in this investigation, Cartridge brass (Cu –
70% and Zn – 30%) is passively fixed on the boring bar and also
clearance is provided in order to reduce the displacement, tool wear
and cutting temperature. A conventional all geared lathe is attached
with vibrometer and pyrometer is used to measure the displacement
and temperature. The influence of input parameters such as cutting
speed, depth of cut and clearance on temperature, tool wear and
displacement are investigated for various cutting conditions. From
the result, the optimum conditions to obtain better damping in boring
process for chatter reduction is identified.
Abstract: This paper presents the advantages of fuzzy control use in technological processes control. The paper presents a real application of the Linguistic Fuzzy-Logic Control, developed at the University of Ostrava for the control of physical models in the Intelligent Systems Laboratory. The paper presents an example of a sensitive non-linear model, such as a magnetic levitation model and obtained results which show how modern information technologies can help to solve actual technical problems. A special method based on the LFLC controller with partial components is presented in this paper followed by the method of automatic context change, which is very helpful to achieve more accurate control results. The main advantage of the used system is its robustness in changing conditions demonstrated by comparing with conventional PID controller. This technology and real models are also used as a background for problem-oriented teaching, realized at the department for master students and their collaborative as well as individual final projects.
Abstract: Imperialist Competitive Algorithm (ICA) is a recent
meta-heuristic method that is inspired by the social evolutions for
solving NP-Hard problems. The ICA is a population-based algorithm
which has achieved a great performance in comparison to other metaheuristics.
This study is about developing enhanced ICA approach to
solve the Cell Formation Problem (CFP) using sequence data. In
addition to the conventional ICA, an enhanced version of ICA,
namely EICA, applies local search techniques to add more
intensification aptitude and embed the features of exploration and
intensification more successfully. Suitable performance measures are
used to compare the proposed algorithms with some other powerful
solution approaches in the literature. In the same way, for checking
the proficiency of algorithms, forty test problems are presented. Five
benchmark problems have sequence data, and other ones are based on
0-1 matrices modified to sequence based problems. Computational
results elucidate the efficiency of the EICA in solving CFP problems.
Abstract: A large variety of pipe flange is required in marine
and construction industry. Pipe flanges are usually welded or screwed
to the pipe end and are connected with bolts. This approach is very
simple and widely used for a long time; however, it results in high
development cost and low productivity, and the productions made by
this approach usually have safety problem at the welding area. In this
research, a new approach of forming pipe flange based on cold
forging and floating die concept is presented. This innovative
approach increases the effectiveness of the material usage and save
the time cost compared with conventional welding method. To ensure the dimensional accuracy of the final product, the finite
element analysis (FEA) was carried out to simulate the process of
cold forging, and the orthogonal experiment methods were used to
investigate the influence of four manufacturing factors (pin die angle,
pipe flange angle, rpm, pin die distance from clamp jig) and predicted
the best combination of them. The manufacturing factors were
obtained by numerical and experimental studies and it shows that the
approach is very useful and effective for the forming of pipe flange,
and can be widely used later.
Abstract: In this talk, we introduce a newly developed quantile
function model that can be used for estimating conditional
distributions of financial returns and for obtaining multi-step ahead
out-of-sample predictive distributions of financial returns. Since we
forecast the whole conditional distributions, any predictive quantity
of interest about the future financial returns can be obtained simply
as a by-product of the method. We also show an application of the
model to the daily closing prices of Dow Jones Industrial Average
(DJIA) series over the period from 2 January 2004 - 8 October 2010.
We obtained the predictive distributions up to 15 days ahead for
the DJIA returns, which were further compared with the actually
observed returns and those predicted from an AR-GARCH model.
The results show that the new model can capture the main features
of financial returns and provide a better fitted model together with
improved mean forecasts compared with conventional methods. We
hope this talk will help audience to see that this new model has the
potential to be very useful in practice.
Abstract: Ocean current is always available around the
surrounding of SHELL Sabah Water Platform and data are collected
every 10 minutes, 24 hours a day, for a period of 365 days. Due to
low current speed, conventional hydrokinetic power generation is not
feasible, thus leading to the study of low current enabled vortex
induced vibration power generation application. In this case, the
design of a vortex induced vibration application is studied to obtain
an optimum design for the VIV oscillator. Power output is then
determined to study the feasibility of the VIV application in low
current condition.
Abstract: New and more powerful communications technologies
continue to emerge at a rapid pace and their uses in education are
widespread and the impact remarkable in the developing societies.
This study investigates Mobile Collaboration Learning Technique
(MCLT) on learners’ outcome among students in tertiary institutions
of developing nations (a case of Nigeria students). It examines the
significance of retention achievement scores of students taught using
mobile collaboration and conventional method. The sample consisted
of 120 students using Stratified random sampling method. Five
research questions and hypotheses were formulated, and tested at
0.05 level of significance. A student achievement test (SAT) was
made of 40 items of multiple-choice objective type, developed and
validated for data collection by professionals. The SAT was
administered to students as pre-test and post-test. The data were
analyzed using t-test statistic to test the hypotheses. The result
indicated that students taught using MCLT performed significantly
better than their counterparts using the conventional method of
instruction. Also, there was no significant difference in the post-test
performance scores of male and female students taught using MCLT.
Based on the findings, the following submissions was made that:
Mobile collaboration system be encouraged in the institutions to
boost knowledge sharing among learners, workshop and training
should be organized to train teachers on the use of this technique,
schools and government should consistently align curriculum
standard to trends of technological dictates and formulate policies
and procedures towards responsible use of MCLT.
Abstract: Asphalt concrete pavements have a short life cycle,
failing mainly due to temperature changes, traffic loading and ageing.
Modified asphalt mixtures provide the technology to produce a
bituminous binder with improved viscoelastic properties, which
remain in balance over a wider temperature range and loading
conditions. In this research, 60/70 penetration grade asphalt binder
was modified by adding 2, 4, 6, 8 and 10 percent by weight of asphalt
binder following the wet process and the mineral aggregate was
modified by adding 1, 2, 3, 4 and 5 percent crumb rubber by volume
of the mineral aggregate following the dry process. The LDPE
modified asphalt binder rheological properties were evaluated. The
laboratory results showed an increase in viscosity, softening point
and stiffness of the binder. The modified asphalt was then used in
preparing asphalt mixtures by Marshall Mix design procedure. The
Marshall Stability values for mixes containing 2% crumb rubber and
4% LDPE were found to be 30% higher than the conventional asphalt
concrete mix.
Abstract: The work reported through this paper is an
experimental work conducted on High Performance Concrete (HPC)
with super plasticizer with the aim to develop some models suitable
for prediction of compressive strength of HPC mixes. In this study,
the effect of varying proportions of fly ash (0% to 50% @ 10%
increment) on compressive strength of high performance concrete has
been evaluated. The mix designs studied were M30, M40 and M50 to
compare the effect of fly ash addition on the properties of these
concrete mixes. In all eighteen concrete mixes that have been
designed, three were conventional concretes for three grades under
discussion and fifteen were HPC with fly ash with varying
percentages of fly ash. The concrete mix designing has been done in
accordance with Indian standard recommended guidelines. All the
concrete mixes have been studied in terms of compressive strength at
7 days, 28 days, 90 days, and 365 days. All the materials used have
been kept same throughout the study to get a perfect comparison of
values of results. The models for compressive strength prediction
have been developed using Linear Regression method (LR), Artificial
Neural Network (ANN) and Leave-One-Out Validation (LOOV)
methods.
Abstract: This paper illustrates the background of various
concepts, approaches, terminologies used to describe the basic
framework of an Islamic Hotel Room design. This paper reviews the
theoretical views in establishing a suitable and optimum environment
for Muslim as well as non-Muslim guests in hotel rooms while
according to shariah. It involves a few research methodologies that
requires the researcher to study on a few characteristics needed to
create more efficient rooms in terms of social interaction, economic
growth and other tolerable elements. This paper intends on revealing
the elements that are vital and may contribute for hotels in achieving
a more conclusive research on space planning for hotel rooms
focusing on the shariah and Muslim guests. Malaysia is an Islamic
country and has billion of tourists coming over for business and
recreational purposes. Therefore, having a righteous environment that
best suit this target user is important in terms of generating the
economy as well as providing a better understanding to the
community on the benefits of applying these qualities in a
conventional resort design.
Abstract: A Mobile Adhoc Network (MANET) is a collection of mobile nodes that communicate with each other with wireless links and without pre-existing communication infrastructure. Routing is an important issue which impacts network performance. As MANETs lack central administration and prior organization, their security concerns are different from those of conventional networks. Wireless links make MANETs susceptible to attacks. This study proposes a new trust mechanism to mitigate wormhole attack in MANETs. Different optimization techniques find available optimal path from source to destination. This study extends trust and reputation to an improved link quality and channel utilization based Adhoc Ondemand Multipath Distance Vector (AOMDV). Differential Evolution (DE) is used for optimization.