Abstract: The seriously damaged structures during earthquakes
show the need and importance of design of reinforced concrete
structures with high ductility. Reinforced concrete beam-column
joints have an important function in all structures. Under seismic
excitation, the beam column joint region is subjected to horizontal
and vertical shear forces whose magnitude is many times higher than
the adjacent beam and column. Strength and ductility of structures
depends mainly on proper detailing of the reinforcement in beamcolumn
joints and the old structures were found ductility deficient.
DSP materials are obtained by using high quantities of super
plasticizers and high volumes of micro silica. In the case of High
Performance Densified Small Particle Concrete (HPDSPC), since
concrete is dense even at the micro-structure level, tensile strain
would be much higher than that of the conventional SFRC, SIFCON
& SIMCON. This in turn will improve cracking behaviour, ductility
and energy absorption capacity of composites in addition to
durability. The fine fibers used in our mix are 0.3mm diameter and 10
mm which can be easily placed with high percentage. These fibers
easily transfer stresses and act as a composite concrete unit to take up
extremely high loads with high compressive strength. HPDSPC
placed in the beam column joints helps in safety of human life due to
prolonged failure.
Abstract: The conventional ceramic route was utilized to
prepare a hard magnetic powder (M-type strontium ferrite,
SrFe12O19). The stoichiometric mixture of iron oxide and strontium
carbonate were calcined at 1000oC and then fired at various
temperatures. The influence of various reaction parameters such as
mixing ratio, calcination temperature, firing temperature and firing
time on the magnetic behaviors of the synthesized magnetic powder
were investigated. The magnetic properties including Coercivity
(Hc), Magnetic saturation (Ms), and Magnetic remnance (Mr) were
measured by vibrating sample magnetometer. Morphologically the
produced magnetic powder has a dense hexagonal grain shape
structure.
Abstract: Review of studies carried out on the use of bagasse
ash for the improvement of deficient soils in Nigeria, with emphasis
on lateritic and black cotton soils is presented. Although, the bagasse
ash is mostly used as additive to the conventional soil stabilizers
(cement and lime), the studies generally showed improvement in the
geotechnical properties of the soils, either modified or stabilized with
the ash. This showed the potentials of using this agricultural waste
(bagasse ash) in the improvement of geotechnical properties of
deficient soils, thus suggesting that using this material at large scale
level in geotechnical engineering practice could help in the provision
of stable and durable structures, reduce cost of soil improvement and
also reduces environmental nuisance caused by the unused waste in
Nigeria.
Abstract: Multiphase Induction Machine (IM) is normally
controlled using rotor field oriented vector control. Under phase(s)
loss, the machine currents can be optimally controlled to satisfy
certain optimization criteria. In this paper we discuss the performance
of double manifold sliding mode observer (DM-SMO) in Sensorless
control of multiphase induction machine under unsymmetrical
condition (one phase loss). This observer is developed using the IM
model in the stationary reference frame. DM-SMO is constructed by
adding extra feedback term to conventional single mode sliding mode
observer (SM-SMO) which proposed in many literature. This leads to
a fully convergent observer that also yields an accurate estimate of
the speed and stator currents. It will be shown by the simulation
results that the estimated speed and currents by the method are very
well and error between real and estimated quantities is negligible.
Also parameter sensitivity analysis shows that this method is rather
robust against parameter variation.
Abstract: The Adaptive Line Enhancer (ALE) is widely used for
enhancing narrowband signals corrupted by broadband noise. In this
paper, we propose novel ALE methods to improve the enhancing
capability. The proposed methods are motivated by the fact that the
output of the ALE is a fine estimate of the desired narrowband signal
with the broadband noise component suppressed. The proposed
methods preprocess the input signal using ALE filter to regenerate a
finer input signal. Thus the proposed ALE is driven by the input signal
with higher signal-to-noise ratio (SNR). The analysis and simulation
results are presented to demonstrate that the proposed ALE has better
performance than conventional ALE’s.
Abstract: This paper describes how to dimension the electric
components of a 48V hybrid system considering real customer use.
Furthermore, it provides information about savings in energy and
CO2 emissions by a customer-tailored 48V hybrid. Based on measured customer profiles, the electric units such as the
electric motor and the energy storage are dimensioned. Furthermore,
the CO2 reduction potential in real customer use is determined
compared to conventional vehicles. Finally, investigations are carried
out to specify the topology design and preliminary considerations in
order to hybridize a conventional vehicle with a 48V hybrid system.
The emission model results from an empiric approach also taking into
account the effects of engine dynamics on emissions. We analyzed
transient engine emissions during representative customer driving
profiles and created emission meta models. The investigation showed
a significant difference in emissions when simulating realistic
customer driving profiles using the created verified meta models
compared to static approaches which are commonly used for vehicle
simulation.
Abstract: As a by-product of the biodiesel industries, glycerol
has been vastly generated which surpasses the market demand. It is
imperative to develop an efficient glycerol valorization processes in
minimizing the net energy requirement and intensifying the biodiesel
production. In this study, base-catalyzed transesterification of
glycerol with dimethyl carbonate using microwave irradiation as
heating method to produce glycerol carbonate was conducted by
varying grades of glycerol, i.e. 70%, 86% and 99% purity, that is
obtained from biodiesel plant. Metal oxide catalysts were used with
varying operating parameters including reaction time, DMC/glycerol
molar ratio, catalyst weight %, temperature and stirring speed. From
the study on the effect of different operating parameters it was found
that the type of catalyst used has the most significant effect on the
transesterification reaction. Amidst the metal oxide catalysts
examined, CaO gave the best performance. This study indicates the
feasibility of producing glycerol carbonate using different grade of
glycerol in both conventional thermal activation and microwave
irradiation with CaO as catalyst. Microwave assisted
transesterification (MAT) of glycerol into glycerol carbonate has
demonstrated itself as an energy efficient route by achieving 94.2%
yield of GC at 65°C, 5 minutes reaction time, 1 wt% CaO and
DMC/glycerol molar ratio of 2. The advantages of MAT
transesterification route has made the direct utilization of bioglycerol
from biodiesel production without the need of purification. This has
marked a more economical and less-energy intensive glycerol
carbonate synthesis route.
Abstract: Fiber Reinforced Polymer (FRP) is a composite material with exceptional properties that are capable to replace conventional steel reinforcement in reinforced and pre-stressed concrete structures. However, the main obstacle for their wide use in pre-stressed concrete application is the anchorage system. Due to the weakness of FRP in the transverse direction, the pre-stressing capacity of FRP bars are limited. This paper investigates the modification of the conventional wedge anchorage system to be used for stressing of FRP bars in pre-stressed applications. Epoxy adhesive material with glass FRP (GFRP) bars and conventional steel wedge were used in this paper. The GFRP bars are encased with epoxy at the anchor zone and the wedge system was used in pull-out test. The results showed a loading capacity of 47.6 kN which is 69% of the bar ultimate capacity. Additionally, nylon wedge was made with the same dimensions of the steel wedge and tested for GFRP bars without epoxy layer. The nylon wedge showed a loading capacity of 19.7 kN which is only 28.5% of the ultimate bar capacity.
Abstract: The present study aims to investigate the performance
of Moringa oleifera seed extract as natural coagulant in clarification
of secondary wastewater treatment plant (MWWTP) located in East
of Algiers, Algeria. Coagulation flocculation performance of
Moringa oleifera was evaluated through supernatant residual
turbidity after jar test trials. Various influence parameters namely
Moringa oleifera dosage and pH have been considered. Tests on
Reghaia wastewater, having 129 NTU of initial turbidity, showed a
removal of 69.45% of residual turbidity with only 1.5 mg/l of
Moringa oleifera. This sufficient removal capability encourages the
use of this bioflocculant for treatment of turbid waters. Indeed,
Moringa oleifera which is a natural resource available locally (South
of Algeria) coupled to the non-toxicity, biocompatibility and
biodegradability, may be a very interesting alternative to the
conventional coagulants used so far.
Abstract: Multiple-input multiple-output (MIMO) radar has
received increasing attention in recent years. MIMO radar has many
advantages over conventional phased array radar such as target
detection,resolution enhancement, and interference suppression. In
this paper, the results are presented from a simulation study of MIMO
uniformly-spaced linear array (ULA) antennas. The performance is
investigated under varied parameters, including varied array size,
pseudo random (PN) sequence length, number of snapshots, and
signal to noise ratio (SNR). The results of MIMO are compared to a
traditional array antenna.
Abstract: This study presents three different approaches to
estimate bubble point pressures for the binary system of CO2 and
ethyl palmitate fatty acid ethyl ester. The first method involves the
Peng-Robinson (PR) Equation of State (EoS) with the conventional
mixing rule of Van der Waals. The second approach involves the PR
EOS together with the Wong Sandler (WS) mixing rule, coupled with
the UNIQUAC GE model. In order to model the bubble point
pressures with this approach, the volume and area parameter for ethyl
palmitate were estimated by the Hansen group contribution method.
The last method involved the Peng-Robinson, combined with the
Wong-Sandler method, but using NRTL as the GE model. Results
using the Van der Waals mixing rule clearly indicated that this
method has the largest errors among all three methods, with errors in
the range of 3.96-6.22%. The PR-WS-UNIQUAC method exhibited
small errors, with average absolute deviations between 0.95 to 1.97
percent. The PR-WS-NRTL method led to the least errors, where
average absolute deviations ranged between 0.65-1.7%.
Abstract: One of the most critical decision points in the design of a
face recognition system is the choice of an appropriate face representation.
Effective feature descriptors are expected to convey sufficient, invariant
and non-redundant facial information. In this work we propose a set of
Hahn moments as a new approach for feature description. Hahn moments
have been widely used in image analysis due to their invariance, nonredundancy
and the ability to extract features either globally and locally.
To assess the applicability of Hahn moments to Face Recognition we
conduct two experiments on the Olivetti Research Laboratory (ORL)
database and University of Notre-Dame (UND) X1 biometric collection.
Fusion of the global features along with the features from local facial
regions are used as an input for the conventional k-NN classifier. The
method reaches an accuracy of 93% of correctly recognized subjects for
the ORL database and 94% for the UND database.
Abstract: Because current wireless communication requires high
reliability in a limited bandwidth environment, this paper proposes
the variable modulation scheme based on the codebook. The variable
modulation scheme adjusts transmission power using the codebook in
accordance with channel state. Also, if the codebook is composed of
many bits, the reliability is more improved by the proposed scheme.
The simulation results show that the performance of proposed scheme
has better reliability than the the performance of conventional scheme.
Abstract: Wireless Sensor Networks (WSNs) enable new
applications and need non-conventional paradigms for the protocol
because of energy and bandwidth constraints, In WSN, sensor node’s
life is a critical parameter. Research on life extension is based on
Low-Energy Adaptive Clustering Hierarchy (LEACH) scheme,
which rotates Cluster Head (CH) among sensor nodes to distribute
energy consumption over all network nodes. CH selection in WSN
affects network energy efficiency greatly. This study proposes an
improved CH selection for efficient data aggregation in sensor
networks. This new algorithm is based on Bacterial Foraging
Optimization (BFO) incorporated in LEACH.
Abstract: Workflow scheduling is an important part of cloud
computing and based on different criteria it decides cost, execution
time, and performances. A cloud workflow system is a platform
service facilitating automation of distributed applications based on
new cloud infrastructure. An aspect which differentiates cloud
workflow system from others is market-oriented business model, an
innovation which challenges conventional workflow scheduling
strategies. Time and Cost optimization algorithm for scheduling
Hybrid Clouds (TCHC) algorithm decides which resource should be
chartered from public providers is combined with a new De-De
algorithm considering that every instance of single and multiple
workflows work without deadlocks. To offset this, two new concepts
- De-De Dodging Algorithm and Priority Based Decisive Algorithm -
combine with conventional deadlock avoidance issues by proposing
one algorithm that maximizes active (not just allocated) resource use
and reduces Makespan.
Abstract: Grains, including oats (Avena sativa L.), have been
recognized functional foods, because provide beneficial effect on the
health of the consumer and decrease the risk of various diseases. Oats
are good source of soluble fibre, essential amino acids, unsaturated
fatty acids, vitamins and minerals. Oat breeders have developed oat
varieties and improved yielding ability potential of oat varieties.
Therefore, the aim of investigation was to analyze the composition of
perspective oat varieties and breeding lines grains grown in different
conditions and evaluate functional properties. In the studied samples
content of protein, starch, β-glucans, total dietetic fibre, composition
of amino acids and vitamin E were determined. The results of
analysis showed that protein content depending of varieties ranged
9.70% to 17.30% total dietary fibre 13.66 g100g-1 to 30.17 g100g-1,
content of β-glucans 2.7 g100g-1 to 3.5 g100g-1, amount of
vitamin E (α-tocopherol) determined from 4 mgkg-1 to 9.9 mgkg-1.
The sums of essential amino acids in oat grain samples were
determined from 31.63 gkg-1 to 54.90 gkg-1. It is concluded that
amino acids composition of husked and naked oats grown in organic
or conventional conditions is close to optimal for human health.
Abstract: Chalcopyrite (CuFeS2) is the most common primary
mineral used for the commercial production of copper. The low
dissolution efficiency of chalcopyrite in sulfate media has prevented
an efficient industrial leaching of this mineral in sulfate media. Ferric
ions, bacteria, oxygen and other oxidants have been used as oxidizing
agents in the leaching of chalcopyrite in sulfate and chloride media
under atmospheric or pressure leaching conditions. Two leaching
methods were studied to evaluate chalcopyrite (CuFeS2) dissolution
in acid media. First, the conventional oxidative acid leaching method
was carried out using sulfuric acid (H2SO4) and potassium
dichromate (K2Cr2O7) as oxidant at atmospheric pressure. Second,
microwave-assisted acid leaching was performed using the
microwave accelerated reaction system (MARS) for same reaction
media. Parameters affecting the copper extraction such as leaching
time, leaching temperature, concentration of H2SO4 and
concentration of K2Cr2O7 were investigated. The results of
conventional acid leaching experiments were compared to the
microwave leaching method. It was found that the copper extraction
obtained under high temperature and high concentrations of oxidant
with microwave leaching is higher than those obtained
conventionally. 81% copper extraction was obtained by the
conventional oxidative acid leaching method in 180 min, with the
concentration of 0.3 mol/L K2Cr2O7 in 0.5M H2SO4 at 50 ºC, while
93.5% copper extraction was obtained in 60 min with microwave
leaching method under same conditions.
Abstract: Currently there are many use of threaded reinforcing
bars in construction fields because those do not need additional screw
processing when connecting reinforcing bar by threaded coupler. In
this study, reinforced concrete bridge piers using threaded rebar
coupler system at the plastic hinge area were tested to evaluate seismic
performance. The test results showed that threads of the threaded rebar
coupler system could be loosened while under tension-compression
cyclic loading because tolerance and rib face angle of a threaded rebar
coupler system are greater than that of a conventional ribbed rebar
coupler system. As a result, cracks were concentrated just outside of
the mechanical coupler and stiffness of reinforced concrete bridge pier
decreased. Therefore, it is recommended that connection ratio of
mechanical couplers in one section shall be below 50% in order that
cracks are not concentrated just outside of the mechanical coupler.
Also, reduced stiffness of the specimen should be considered when
using the threaded rebar coupler system.
Abstract: In the cooperative transmission scheme, both the
cellular system and broadcasting system are composed. Two cellular
base stations (CBSs) communicating with a user in the cell edge use
cooperative transmission scheme in the conventional scheme. In the
case that the distance between two CBSs and the user is distant, the
conventional scheme does not guarantee the quality of the
communication because the channel condition is bad. Therefore, if the
distance between CBSs and a user is distant, the performance of the
conventional scheme is decreased. Also, the bad channel condition has
bad effects on the performance. The proposed scheme uses two relays
to communicate well with CBSs when the channel condition between
CBSs and the user is poor. Using the relay in the high attenuation
environment can obtain both advantages of the high bit error rate
(BER) and throughput performance.
Abstract: Numerical studies have been carried out using a
validated two-dimensional standard k-omega turbulence model for
the design optimization of a thrust vector control system using shock
induced self-impinging supersonic secondary double jet. Parametric
analytical studies have been carried out at different secondary
injection locations to identifying the highest unsymmetrical
distribution of the main gas flow due to shock waves, which produces
a desirable side force more lucratively for vectoring. The results from
the parametric studies of the case on hand reveal that the shock
induced self-impinging supersonic secondary double jet is more
efficient in certain locations at the divergent region of a CD nozzle
than a case with supersonic single jet with same mass flow rate. We
observed that the best axial location of the self-impinging supersonic
secondary double jet nozzle with a given jet interaction angle, built-in
to a CD nozzle having area ratio 1.797, is 0.991 times the primary
nozzle throat diameter from the throat location. We also observed
that the flexible steering is possible after invoking ON/OFF facility to
the secondary nozzles for meeting the onboard mission requirements.
Through our case studies we concluded that the supersonic self-impinging
secondary double jet at predesigned jet interaction angle
and location can provide more flexible steering options facilitating
with 8.81% higher thrust vectoring efficiency than the conventional
supersonic single secondary jet without compromising the payload
capability of any supersonic aerospace vehicle.