Abstract: This paper describes the development of a control
system model using a graphical software tool. This control system is
part of an operator training simulator developed for the National
Training Center for Operators of Ixtapantongo (CNCAOI, acronym
according to its name in Spanish language) of the Mexico-s Federal
Commission of Electricity, CFE). The Department of Simulation of
the Electrical Research Institute (IIE) developed this simulator using
as reference the Unit I of the Combined Cycle Power Plant El Sauz,
located at the centre of Mexico. The first step in the project was the
developing of the Gas Turbine System and its control system
simulator. The Turbo Gas simulator was finished and delivered to
CNCAOI in March 2007 for commercial operation. This simulator is
a high-fidelity real time dynamic simulator built and tested for
accurate operation over the entire load range. The simulator was used
primarily for operator training although it has been used for
procedure development and evaluation of plant transients.
Abstract: Three-dimensional simulation of harmonic up
generation in free electron laser amplifier operating simultaneously
with a cold and relativistic electron beam is presented in steady-state
regime where the slippage of the electromagnetic wave with respect
to the electron beam is ignored. By using slowly varying envelope
approximation and applying the source-dependent expansion to wave
equations, electromagnetic fields are represented in terms of the
Hermit Gaussian modes which are well suited for the planar wiggler
configuration. The electron dynamics is described by the fully threedimensional
Lorentz force equation in presence of the realistic planar
magnetostatic wiggler and electromagnetic fields. A set of coupled
nonlinear first-order differential equations is derived and solved
numerically. The fundamental and third harmonic radiation of the
beam is considered. In addition to uniform beam, prebunched
electron beam has also been studied. For this effect of sinusoidal
distribution of entry times for the electron beam on the evolution of
radiation is compared with uniform distribution. It is shown that
prebunching reduces the saturation length substantially. For
efficiency enhancement the wiggler is set to decrease linearly when
the radiation of the third harmonic saturates. The optimum starting
point of tapering and the slope of radiation in the amplitude of
wiggler are found by successive run of the code.
Abstract: Most of the commonly used blind equalization algorithms are based on the minimization of a nonconvex and nonlinear cost function and a neural network gives smaller residual error as compared to a linear structure. The efficacy of complex valued feedforward neural networks for blind equalization of linear and nonlinear communication channels has been confirmed by many studies. In this paper we present two neural network models for blind equalization of time-varying channels, for M-ary QAM and PSK signals. The complex valued activation functions, suitable for these signal constellations in time-varying environment, are introduced and the learning algorithms based on the CMA cost function are derived. The improved performance of the proposed models is confirmed through computer simulations.
Abstract: Brick is one of the most common masonry units used as building material. Due to the demand, different types of waste have been investigated to be incorporated into the bricks. Many types of sludge have been incorporated in fired clay brick for example marble sludge, stone sludge, water sludge, sewage sludge, and ceramic sludge. The utilization of these waste materials in fired clay bricks usually has positive effects on the properties such as lightweight bricks with improved shrinkage, porosity, and strength. This paper reviews on utilization of different types of sludge wastes into fired clay bricks. Previous investigations have demonstrated positive effects on the physical and mechanical properties as well as less impact towards the environment. Thus, the utilizations of sludge waste could produce a good quality of brick and could be one of alternative disposal methods for the sludge wastes.
Abstract: In this paper, a low noise microwave bandpass filter
(BPF) is presented. This filter is fabricated by modifying the
conventional cross-coupled structure. The spurious response is
improved by using the end open coupled lines, and the influence of the
noise is minimized. Impedance matrix of the open end coupled circuit
clarifies the characteristic of the suppression of the spurious response.
The rejection of spurious suppression region of the proposed filter is
greater than 20 dB from 3-13 GHz. The measured results of the
fabricated filter confirm the concepts of the proposed design and
exhibits high performance.
Abstract: The governing two-dimensional equations of a heterogeneous material composed of a fluid (allowed to flow in the absence of acoustic excitations) and a crystalline piezoelectric cubic solid stacked one-dimensionally (along the z direction) are derived and special emphasis is given to the discussion of acoustic group velocity for the structure as a function of the wavenumber component perpendicular to the stacking direction (being the x axis). Variations in physical parameters with y are neglected assuming infinite material homogeneity along the y direction and the flow velocity is assumed to be directed along the x direction. In the first part of the paper, the governing set of differential equations are derived as well as the imposed boundary conditions. Solutions are provided using Hamilton-s equations for the wavenumber vs. frequency as a function of the number and thickness of solid layers and fluid layers in cases with and without flow (also the case of a position-dependent flow in the fluid layer is considered). In the first part of the paper, emphasis is given to the small-frequency case. Boundary conditions at the bottom and top parts of the full structure are left unspecified in the general solution but examples are provided for the case where these are subject to rigid-wall conditions (Neumann boundary conditions in the acoustic pressure). In the second part of the paper, emphasis is given to the general case of larger frequencies and wavenumber-frequency bandstructure formation. A wavenumber condition for an arbitrary set of consecutive solid and fluid layers, involving four propagating waves in each solid region, is obtained again using the monodromy matrix method. Case examples are finally discussed.
Abstract: The Swine flu outbreak in humans is due to a new
strain of influenza A virus subtype H1N1 that derives in part from
human influenza, avian influenza, and two separated strains of swine
influenza. It can be transmitted from human to human. A
mathematical model for the transmission of Swine flu is developed in
which the human populations are divided into two classes, the risk
and non-risk human classes. Each class is separated into susceptible,
exposed, infectious, quarantine and recovered sub-classes. In this
paper, we formulate the dynamical model of Swine flu transmission
and the repetitive contacts between the people are also considered.
We analyze the behavior for the transmission of this disease. The
Threshold condition of this disease is found and numerical results are
shown to confirm our theoretical predictions.
Abstract: This study aimed to evaluate regional soil Borkhar of
the metals Lead has been made. In this field study fires visits to the
regions. The limit of this study located in the East refineries,
petrochemical and power plant to 20 km was selected. The 41 soil
samples from depths of 0 to 10 cm in area and were randomized. Soil
samples were transported to the laboratory and by air was dry and
passed through 2-mil thickness sieve. In the laboratory of physical
and chemical characteristics and concentrations of total absorption
was measured. The results showed that the amount of lead in soil in
many parts of the range higher than the standard limit. Survey maps
show that the lead spatial distribution of the region does not special
pattern.
Abstract: This paper describes a one-dimensional numerical model for natural gas production from the dissociation of methane hydrate in hydrate-capped gas reservoir under depressurization and thermal stimulation. Some of the hydrate reservoirs discovered are overlying a free-gas layer, known as hydrate-capped gas reservoirs. These reservoirs are thought to be easiest and probably the first type of hydrate reservoirs to be produced. The mathematical equations that can be described this type of reservoir include mass balance, heat balance and kinetics of hydrate decomposition. These non-linear partial differential equations are solved using finite-difference fully implicit scheme. In the model, the effect of convection and conduction heat transfer, variation change of formation porosity, the effect of using different equations of state such as PR and ER and steam or hot water injection are considered. In addition distributions of pressure, temperature, saturation of gas, hydrate and water in the reservoir are evaluated. It is shown that the gas production rate is a sensitive function of well pressure.
Abstract: This paper aims to establish a delayed dynamical relationship between payoffs of players in a zero-sum game. By introducing Markovian chain and time delay in the network model, a delayed game network model with sector bounds and slope bounds restriction nonlinear function is first proposed. As a result, a direct dynamical relationship between payoffs of players in a zero-sum game can be illustrated through a delayed singular system. Combined with Finsler-s Lemma and Lyapunov stable theory, a sufficient condition guaranteeing the unique existence and stability of zero-sum game-s Nash equilibrium is derived. One numerical example is presented to illustrate the validity of the main result.
Abstract: In this paper, we first give the representation of the general solution of the following least-squares problem (LSP): Given matrices X ∈ Rn×p, B ∈ Rp×p and A0 ∈ Rr×r, find a matrix A ∈ Rn×n such that XT AX − B = min, s. t. A([1, r]) = A0, where A([1, r]) is the r×r leading principal submatrix of the matrix A. We then consider a best approximation problem: given an n × n matrix A˜ with A˜([1, r]) = A0, find Aˆ ∈ SE such that A˜ − Aˆ = minA∈SE A˜ − A, where SE is the solution set of LSP. We show that the best approximation solution Aˆ is unique and derive an explicit formula for it. Keyw
Abstract: Panoramic view generation has always offered
novel and distinct challenges in the field of image processing.
Panoramic view generation is nothing but construction of bigger
view mosaic image from set of partial images of the desired view.
The paper presents a solution to one of the problems of image
seascape formation where some of the partial images are color and
others are grayscale. The simplest solution could be to convert all
image parts into grayscale images and fusing them to get grayscale
image panorama. But in the multihued world, obtaining the colored
seascape will always be preferred. This could be achieved by picking
colors from the color parts and squirting them in grayscale parts of
the seascape. So firstly the grayscale image parts should be colored
with help of color image parts and then these parts should be fused to
construct the seascape image.
The problem of coloring grayscale images has no exact solution.
In the proposed technique of panoramic view generation, the job of
transferring color traits from reference color image to grayscale
image is done by palette based method. In this technique, the color
palette is prepared using pixel windows of some degrees taken from
color image parts. Then the grayscale image part is divided into pixel
windows with same degrees. For every window of grayscale image
part the palette is searched and equivalent color values are found,
which could be used to color grayscale window. For palette
preparation we have used RGB color space and Kekre-s LUV color
space. Kekre-s LUV color space gives better quality of coloring. The
searching time through color palette is improved over the exhaustive
search using Kekre-s fast search technique.
After coloring the grayscale image pieces the next job is fusion of
all these pieces to obtain panoramic view. For similarity estimation
between partial images correlation coefficient is used.
Abstract: Studies regarding the determination of population
trend of Lipaphis erysimi (kalt.) and its associated natural enemies in
different Brassica lines along with the effect of gamma radiation on
their population were conducted at Agricultural Research Farm,
Malakandher, Khyber Pakhtunkhwa Agricultural University
Peshawar during spring 2006. Three different Brassica lines F6B3,
F6B6 and F6B7 were used, which were replicated four times in
Randomized Complete Block Design. The data revealed that aphid
infestation invariably stated in all three varieties during last week of
February 2006 (1st observation). The peak population of 4.39 aphids
leaf-1 was s recorded during 2nd week of March and lowest population
of 1.02 aphids leaf-1 was recorded during 5th week of March. The
species of lady bird beetle (Coccinella septempunctata) and Syrphid
fly (Syrphus balteatus) first appeared on 24th February with a mean
number of 0.40 lady bird beetle leaf-1 and 0.87 Syrphid fly leaf-1,
respectively. At the time when aphid population started to increase
the peak population of C. septempunctata (0.70 lady bird beetle leaf-
1) and S. balteatus (1.04 syrphid fly leaf-1) was recorded on the 2nd
week of March. Chrysoperla carnea appeared in the 1st week of
March and their peak population was recorded during the 3rd week of
March with mean population of 1.46 C. carnea leaf-1. Among all the
Brassica lines, F6B7 showed comparatively more resistance as
compared to F6B3 F6B6. F6B3 showed least resistance against L.
erysimi, which was found to be the most susceptible cultivar. F6B7
was also found superior in terms of natural enemies. Maximum
number of all natural enemies was recorded on this variety followed
by F6B6. Lowest number of natural enemies was recorded in F6B3.
No significant effect was recorded for the effect of gamma radiation
on the population of aphids, natural enemies and on the varieties.
Abstract: The research objective aims to search information about storytelling and fable associated with fireflies in Amphawa community, in order to design and create a story book which is appropriate for the interests of children in early childhood. This book should help building the development of learning about the natural environment, imagination, and creativity among children, which then, brings about the promotion of the development, conservation and dissemination of cultural values and uniqueness of the Amphawa community. The population used in this study were 30 students in early childhood aged between 6-8 years-old, grade 1-3 from the Demonstration School of Suan Sunandha Rajabhat University. The method used for this study was purposive sampling and the research conducted by the query and analysis of data from both the document and the narrative field tales and fable associated with the fireflies of Amphawa community. Then, using the results to synthesize and create a conceptual design in a form of 8 visual images which were later applied to 1 illustrated children’s book and presented to the experts to evaluate and test this media.
Abstract: This paper studies stability of homogeneous beams
with piezoelectric layers subjected to axial load that is simply
supported at both ends lies on a continuous elastic foundation. The
displacement field of beam is assumed based on first order shear
deformation beam theory. Applying the Hamilton's principle, the
governing equation is established. The influences of applied voltage,
dimensionless geometrical parameter and foundation coefficient on
the stability of beam are presented. To investigate the accuracy of the
present analysis, a compression study is carried out with a known
data.
Abstract: The dominant judgment for earthquake damaged reinforced concrete (RC) structures is to rebuild them with the new ones. Consequently, this paper estimates if there is chance to repair earthquake RC beams and obtain economical contribution to modern day society. Therefore, the totally damaged (damaged in shear under cyclic load) reinforced concrete (RC) beams repaired and strengthened by externally bonded carbon fibre reinforced polymer (CFRP) strips in this study. Four specimens, apart from the reference beam, were separated into two distinct groups. Two experimental beams in the first group primarily tested up to failure then appropriately repaired and strengthened with CFRP strips. Two undamaged specimens from the second group were not repaired but strengthened by the identical strengthening scheme as the first group for comparison. This study studies whether earthquake damaged RC beams that have been repaired and strengthened will validate similar strength and behavior to equally strengthened, undamaged RC beams. Accordingly, a strength correspondence according to strengthened specimens was acquired for the repaired and strengthened specimens. Test results confirmed that repair and strengthening, which were estimated in the experimental program, were effective for the specimens with the cracking patterns considered in the experimental program.
Abstract: The aged are faced with increasing risk for falls. The
aged have the easily fragile bones than others. When falls have
occurred, it is important to detect this emergency state because such
events often lead to more serious illness or even death. A
implementation of PDA system, for detection of emergency situation,
was developed using 3-axis accelerometer in this paper as follows.
The signals were acquired from the 3-axis accelerometer, and then
transmitted to the PDA through Bluetooth module. This system can
classify the human activity, and also detect the emergency state like
falls. When the fall occurs, the system generates the alarm on the
PDA. If a subject does not respond to the alarm, the system determines
whether the current situation is an emergency state or not, and then
sends some information to the emergency center in the case of urgent
situation. Three different studies were conducted on 12 experimental
subjects, with results indicating a good accuracy. The first study was
performed to detect the posture change of human daily activity. The
second study was performed to detect the correct direction of fall. The
third study was conducted to check the classification of the daily
physical activity. Each test was lasted at least 1 min. in third study.
The output of acceleration signal was compared and evaluated by
changing a various posture after attaching a 3-axis accelerometer
module on the chest. The newly developed system has some important
features such as portability, convenience and low cost. One of the
main advantages of this system is that it is available at home
healthcare environment. Another important feature lies in low cost to
manufacture device. The implemented system can detect the fall
accurately, so will be widely used in emergency situation.
Abstract: Data of wave height and wind speed were collected
from three existing oil fields in South China Sea – offshore
Peninsular Malaysia, Sarawak and Sabah regions. Extreme values
and other significant data were employed for analysis. The data were
recorded from 1999 until 2008. The results show that offshore
structures are susceptible to unacceptable motions initiated by wind
and waves with worst structural impacts caused by extreme wave
heights. To protect offshore structures from damage, there is a need
to quantify descriptive statistics and determine spectra envelope of
wind speed and wave height, and to ascertain the frequency content
of each spectrum for offshore structures in the South China Sea
shallow waters using measured time series. The results indicate that
the process is nonstationary; it is converted to stationary process by
first differencing the time series. For descriptive statistical analysis,
both wind speed and wave height have significant influence on the
offshore structure during the northeast monsoon with high mean wind
speed of 13.5195 knots ( = 6.3566 knots) and the high mean wave
height of 2.3597 m ( = 0.8690 m). Through observation of the
spectra, there is no clear dominant peak and the peaks fluctuate
randomly. Each wind speed spectrum and wave height spectrum has
its individual identifiable pattern. The wind speed spectrum tends to
grow gradually at the lower frequency range and increasing till it
doubles at the higher frequency range with the mean peak frequency
range of 0.4104 Hz to 0.4721 Hz, while the wave height tends to
grow drastically at the low frequency range, which then fluctuates
and decreases slightly at the high frequency range with the mean
peak frequency range of 0.2911 Hz to 0.3425 Hz.
Abstract: In order to implement flexibility as well as survivable
capacities over passive optical network (PON), a new automatic
random fault-recovery mechanism with array-waveguide-grating
based (AWG-based) optical switch (OSW) is presented. Firstly,
wavelength-division-multiplexing and optical code-division
multiple-access (WDM/OCDMA) scheme are configured to meet the
various geographical locations requirement between optical network
unit (ONU) and optical line terminal (OLT). The AWG-base optical
switch is designed and viewed as central star-mesh topology to
prohibit/decrease the duplicated redundant elements such as fiber and
transceiver as well. Hence, by simple monitoring and routing switch
algorithm, random fault-recovery capacity is achieved over
bi-directional (up/downstream) WDM/OCDMA scheme. When error
of distribution fiber (DF) takes place or bit-error-rate (BER) is higher
than 10-9 requirement, the primary/slave AWG-based OSW are
adjusted and controlled dynamically to restore the affected ONU
groups via the other working DFs immediately.
Abstract: In this paper, linear multistep technique using power
series as the basis function is used to develop the block methods
which are suitable for generating direct solution of the special second
order ordinary differential equations of the form y′′ = f(x,y), a < = x < = b with associated initial or boundary conditions. The continuaous hybrid formulations enable us to differentiate and evaluate at some
grids and off – grid points to obtain two different three discrete
schemes, each of order (4,4,4)T, which were used in block form for
parallel or sequential solutions of the problems. The computational
burden and computer time wastage involved in the usual reduction of
second order problem into system of first order equations are avoided
by this approach. Furthermore, a stability analysis and efficiency of
the block method are tested on linear and non-linear ordinary
differential equations whose solutions are oscillatory or nearly
periodic in nature, and the results obtained compared favourably with
the exact solution.