Abstract: The three-time-scale plant model of a wind power
generator, including a wind turbine, a flexible vertical shaft, a Variable
Inertia Flywheel (VIF) module, an Active Magnetic Bearing (AMB)
unit and the applied wind sequence, is constructed. In order to make
the wind power generator be still able to operate as the spindle speed
exceeds its rated speed, the VIF is equipped so that the spindle speed
can be appropriately slowed down once any stronger wind field is
exerted. To prevent any potential damage due to collision by shaft
against conventional bearings, the AMB unit is proposed to regulate
the shaft position deviation. By singular perturbation order-reduction
technique, a lower-order plant model can be established for the
synthesis of feedback controller. Two major system parameter
uncertainties, an additive uncertainty and a multiplicative uncertainty,
are constituted by the wind turbine and the VIF respectively.
Frequency Shaping Sliding Mode Control (FSSMC) loop is proposed
to account for these uncertainties and suppress the unmodeled
higher-order plant dynamics. At last, the efficacy of the FSSMC is
verified by intensive computer and experimental simulations for
regulation on position deviation of the shaft and counter-balance of
unpredictable wind disturbance.
Abstract: The main focus of the work was concerned with hydrodynamic and thermal analysis of the plate heat exchanger channel with corrugation patterns suggested to be triangular, sinusoidal, and square corrugation. This study was to numerically model and validate the triangular corrugated channel with dimensions/parameters taken from open literature, and then model/analyze both sinusoidal, and square corrugated channel referred to the triangular model. Initially, 2D modeling with local extensive analysis for triangular corrugated channel was carried out. By that, all local pressure drop, wall shear stress, friction factor, static temperature, heat flux, Nusselt number, and surface heat coefficient, were analyzed to interpret the hydrodynamic and thermal phenomena occurred in the flow. Furthermore, in order to facilitate confidence in this model, a comparison between the values predicted, and experimental results taken from literature for almost the same case, was done. Moreover, a holistic numerical study for sinusoidal and square channels together with global comparisons with triangular corrugation under the same condition, were handled. Later, a comparison between electric, and fluid cooling through varying the boundary condition was achieved. The constant wall temperature and constant wall heat flux boundary conditions were employed, and the different resulted Nusselt numbers as a consequence were justified. The results obtained can be used to come up with an optimal design, a 'compromise' between heat transfer and pressure drop.
Abstract: The aim of this study is evaluating the antinociceptive
and anti-inflamatory activity of Geum kokanicum. After
determination total extract LD50, different doses of extract were
chosen for intrapritoneal injections. In inflammation test, male NMRI
mice were divided into 6 groups: control (normal saline), positive
control (Dexamethasone 15mg/kg), and total extract (0.025, 0.05,
0.1, and 0.2 gr/kg). The inflammation was produced by xyleneinduced
edema. In order to evaluate the antinociceptive effect of total
extract, formalin test was used. Mice were divided into 6 groups:
control, positive control (morphine 10mg/kg), and 4 groups which
received total extract. Then they received Formalin. The animals
were observed for the reaction to pain. Data were analyzed using
One-way ANOVA followed by Tukey-Kramer multiple comparison
test. LD50 was 1 gr/kg. Data indicated that 0.5,0.1 and 0.2 gr/kg
doses of total extract have particular antinociceptive and antiinflammatory
effects in a comparison with control (P
Abstract: Two-dimensional Direct Numerical Simulation (DNS)
of high Schmidt number mass transfer in a convective flow environment
(Rayleigh-B'enard) is carried out and results are compared to
experimental data. A fourth-order accurate WENO-scheme has been
used for scalar transport in order to aim for a high accuracy in areas
of high concentration gradients. It was found that the typical spatial
distance between downward plumes of cold high concentration water
and the eddy size are in good agreement with experiments using a
combined PIV-LIF technique for simultaneous and spatially synoptic
measurements of 2D velocity and concentration fields.
Abstract: One important problem in today organizations is the
existence of non-integrated information systems, inconsistency and
lack of suitable correlations between legacy and modern systems.
One main solution is to transfer the local databases into a global one.
In this regards we need to extract the data structures from the legacy
systems and integrate them with the new technology systems. In
legacy systems, huge amounts of a data are stored in legacy
databases. They require particular attention since they need more
efforts to be normalized, reformatted and moved to the modern
database environments. Designing the new integrated (global)
database architecture and applying the reverse engineering requires
data normalization. This paper proposes the use of database reverse
engineering in order to integrate legacy and modern databases in
organizations. The suggested approach consists of methods and
techniques for generating data transformation rules needed for the
data structure normalization.
Abstract: The study of the transport coefficients in electronic
devices is currently carried out by analytical and empirical models.
This study requires several simplifying assumptions, generally
necessary to lead to analytical expressions in order to study the
different characteristics of the electronic silicon-based devices.
Further progress in the development, design and optimization of
Silicon-based devices necessarily requires new theory and modeling
tools. In our study, we use the PSO (Particle Swarm Optimization)
technique as a computational tool to develop analytical approaches in
order to study the transport phenomenon of the electron in crystalline
silicon as function of temperature and doping concentration. Good
agreement between our results and measured data has been found.
The optimized analytical models can also be incorporated into the
circuits simulators to study Si-based devices without impact on the
computational time and data storage.
Abstract: The algorithm represents the DCT coefficients to concentrate signal energy and proposes combination and dictator to eliminate the correlation in the same level subband for encoding the DCT-based images. This work adopts DCT and modifies the SPIHT algorithm to encode DCT coefficients. The proposed algorithm also provides the enhancement function in low bit rate in order to improve the perceptual quality. Experimental results indicate that the proposed technique improves the quality of the reconstructed image in terms of both PSNR and the perceptual results close to JPEG2000 at the same bit rate.
Abstract: Available Bit Rate Service (ABR) is the lower priority
service and the better service for the transmission of data. On wireline
ATM networks ABR source is always getting the feedback from
switches about increase or decrease of bandwidth according to the
changing network conditions and minimum bandwidth is guaranteed.
In wireless networks guaranteeing the minimum bandwidth is really a
challenging task as the source is always in mobile and traveling from
one cell to another cell. Re establishment of virtual circuits from start
to end every time causes the delay in transmission. In our proposed
solution we proposed the mechanism to provide more available
bandwidth to the ABR source by re-usage of part of old Virtual
Channels and establishing the new ones. We want the ABR source to
transmit the data continuously (non-stop) inorderto avoid the delay.
In worst case scenario at least minimum bandwidth is to be allocated.
In order to keep the data flow continuously, priority is given to the
handoff ABR call against new ABR call.
Abstract: The healthcare environment is generally perceived as
being information rich yet knowledge poor. However, there is a lack
of effective analysis tools to discover hidden relationships and trends
in data. In fact, valuable knowledge can be discovered from
application of data mining techniques in healthcare system. In this
study, a proficient methodology for the extraction of significant
patterns from the Coronary Heart Disease warehouses for heart
attack prediction, which unfortunately continues to be a leading cause
of mortality in the whole world, has been presented. For this purpose,
we propose to enumerate dynamically the optimal subsets of the
reduced features of high interest by using rough sets technique
associated to dynamic programming. Therefore, we propose to
validate the classification using Random Forest (RF) decision tree to
identify the risky heart disease cases. This work is based on a large
amount of data collected from several clinical institutions based on
the medical profile of patient. Moreover, the experts- knowledge in
this field has been taken into consideration in order to define the
disease, its risk factors, and to establish significant knowledge
relationships among the medical factors. A computer-aided system is
developed for this purpose based on a population of 525 adults. The
performance of the proposed model is analyzed and evaluated based
on set of benchmark techniques applied in this classification problem.
Abstract: The Wavelet-Galerkin finite element method for
solving the one-dimensional heat equation is presented in this work.
Two types of basis functions which are the Lagrange and multi-level
wavelet bases are employed to derive the full form of matrix system.
We consider both linear and quadratic bases in the Galerkin method.
Time derivative is approximated by polynomial time basis that
provides easily extend the order of approximation in time space. Our
numerical results show that the rate of convergences for the linear
Lagrange and the linear wavelet bases are the same and in order 2
while the rate of convergences for the quadratic Lagrange and the
quadratic wavelet bases are approximately in order 4. It also reveals
that the wavelet basis provides an easy treatment to improve
numerical resolutions that can be done by increasing just its desired
levels in the multilevel construction process.
Abstract: In this paper, a benchmarking framework is presented
for the performance assessment of irrigations systems. Firstly, a data
envelopment analysis (DEA) is applied to measure the technical
efficiency of irrigation systems. This method, based on linear
programming, aims to determine a consistent efficiency ranking of
irrigation systems in which known inputs, such as water volume
supplied and total irrigated area, and a given output corresponding to
the total value of irrigation production are taken into account
simultaneously. Secondly, in order to examine the irrigation
efficiency in more detail, a cross – system comparison is elaborated
using a performance indicators set selected by IWMI. The above
methodologies were applied in Thessaloniki plain, located in
Northern Greece while the results of the application are presented and
discussed. The conjunctive use of DEA and performance indicators
seems to be a very useful tool for efficiency assessment and
identification of best practices in irrigation systems management.
Abstract: The review performed on the condition of energy
consumption & rate in Iran, shows that unfortunately the subject of
optimization and conservation of energy in active industries of
country lacks a practical & effective method and in most factories,
the energy consumption and rate is more than in similar industries of
industrial countries. The increasing demand of electrical energy and
the overheads which it imposes on the organization, forces
companies to search for suitable approaches to optimize energy
consumption and demand management. Application of value
engineering techniques is among these approaches. Value
engineering is considered a powerful tool for improving profitability.
These tools are used for reduction of expenses, increasing profits,
quality improvement, increasing market share, performing works in
shorter durations, more efficient utilization of sources & etc.
In this article, we shall review the subject of value engineering and
its capabilities for creating effective transformations in industrial
organizations, in order to reduce energy costs & the results have
been investigated and described during a case study in Mazandaran
wood and paper industries, the biggest consumer of energy in north
of Iran, for the purpose of presenting the effects of performed tasks
in optimization of energy consumption by utilizing value engineering
techniques in one case study.
Abstract: This paper implements the inventory model developed in the first part of this paper in a simplified problem to simultaneously reduce costs and risks in JIT systems. This model is developed to ascertain an optimal ordering strategy for procuring raw materials by using regular multi-external and local backup suppliers to reduce the total cost of the products, and at the same time to reduce the risks arising from this cost reduction within production systems. A comparison between the cost of using the JIT system and using the proposed inventory model shows the superiority of the use of the inventory model.
Abstract: This paper presents a new method for the
implementation of a direct rotor flux control (DRFOC) of induction
motor (IM) drives. It is based on the rotor flux components
regulation. The d and q axis rotor flux components feed proportional
integral (PI) controllers. The outputs of which are the target stator
voltages (vdsref and vqsref). While, the synchronous speed is depicted at
the output of rotor speed controller. In order to accomplish variable
speed operation, conventional PI like controller is commonly used.
These controllers provide limited good performances over a wide
range of operations even under ideal field oriented conditions. An
alternate approach is to use the so called fuzzy logic controller. The
overall investigated system is implemented using dSpace system
based on digital signal processor (DSP). Simulation and experimental
results have been presented for a one kw IM drives to confirm the
validity of the proposed algorithms.
Abstract: Minor law breaking seems more and more to be a part
of adolescence behavior. An important risk factor which seems to
influence delinquency appears to be the socio-economic one.
According to Romanian statistics, during the first six months of 2012,
1,378 minors have committed various crimes, the most common
being theft, sexual offenses and violent assaults. Drug-related
offenses did not reach the gravity of those from high income
countries of the European Union, but have a continuous upward
during the last years.
The aim of our research was to examine whether delinquency in
adolescence is correlated to mental disorders or socio-economic and
familial factors. Forensic psychiatric expertise was performed to 79
adolescents who committed offenses between 01 January 2012 and
31 December 2012. Teenagers, with ages between 12 and 17, were
examined by day hospitalization in the University Clinic of
Psychiatry Craiova.
Abstract: In the present paper, active control system is used in
different heights of the building and the most effective part was
studied where the active control system is applied. The mathematical
model of the building is established in MATLAB and in order to
active control the system FLC method was used. Three different
locations of the building are chosen to apply active control system,
namely at the lowest story, the middle height of the building, and at
the highest point of the building with TMD system. The equation of
motion was written for high rise building and it was solved by statespace
method. Also passive control was used with Tuned Mass
Damper (TMD) at the top floor of the building to show the robustness
of FLC method when compared with passive control system.
Abstract: Development of motor car safety devices has reduced
fatality rates in car accidents. Yet despite this increase in car safety,
neck injuries resulting from rear impact collisions, particularly at low
speed, remain a primary concern. In this study, FEA(Finite Element
Analysis) of seat was performed to evaluate neck injuries in rear
impact. And the FEA result was verified by comparison with the actual
test results. The dummy used in FE model and actual test is BioRID II
which is regarded suitable for rear impact collision analysis. A
threshold of the BioRID II neck injury indicators was also proposed to
upgrade seat performance in order to reduce whiplash injury. To
optimize the seat for a low-speed rear impact collision, a method was
proposed, which is multi-objective optimization idea using DOE
(Design of Experiments) results.
Abstract: Disordered function of maniphalanx and difficulty with
ambulation will occur insofar as a human has a failure in the spinal
marrow. Cervical spondylotic myelopathy as one of the myelopathy
emanates from not only external factors but also increased age. In
addition, the diacrisis is difficult since cervical spondylotic
myelopathy is evaluated by a doctor-s neurological remark and
imaging findings. As a quantitative method for measuring the degree
of disability, hand-operated triangle step test (for short, TST) has
formulated. In this research, a full automatic triangle step counter
apparatus is designed and developed to measure the degree of
disability in an accurate fashion according to the principle of TST. The
step counter apparatus whose shape is a low triangle pole displays the
number of stepping upon each corner. Furthermore, the apparatus has
two modes of operation. Namely, one is for measuring the degree of
disability and the other for rehabilitation exercise. In terms of
usefulness, clinical practice should be executed before too long.
Abstract: This study aimed at developing visualization tools for integrating CloudSat images and Water Vapor Satellite images. KML was used for integrating data from CloudSat Satellite and GMS-6 Water Vapor Satellite. CloudSat 2D images were transformed into 3D polygons in order to achieve 3D images. Before overlaying the images on Google Earth, GMS-6 water vapor satellite images had to be rescaled into linear images. Web service was developed using webMathematica. Shoreline from GMS-6 images was compared with shoreline from LandSat images on Google Earth for evaluation. The results showed that shoreline from GMS-6 images was highly matched with the shoreline in LandSat images from Google Earth. For CloudSat images, the visualizations were compared with GMS-6 images on Google Earth. The results showed that CloudSat and GMS-6 images were highly correlated.
Abstract: Certifications such as the Passive House Standard aim to reduce the final space heating energy demand of residential buildings. Space conditioning, notably heating, is responsible for nearly 70% of final residential energy consumption in Europe. There is therefore significant scope for the reduction of energy consumption through improvements to the energy efficiency of residential buildings. However, these certifications totally overlook the energy embodied in the building materials used to achieve this greater operational energy efficiency. The large amount of insulation and the triple-glazed high efficiency windows require a significant amount of energy to manufacture. While some previous studies have assessed the life cycle energy demand of passive houses, including their embodied energy, these rely on incomplete assessment techniques which greatly underestimate embodied energy and can lead to misleading conclusions. This paper analyses the embodied and operational energy demands of a case study passive house using a comprehensive hybrid analysis technique to quantify embodied energy. Results show that the embodied energy is much more significant than previously thought. Also, compared to a standard house with the same geometry, structure, finishes and number of people, a passive house can use more energy over 80 years, mainly due to the additional materials required. Current building energy efficiency certifications should widen their system boundaries to include embodied energy in order to reduce the life cycle energy demand of residential buildings.