Abstract: In this paper, we introduced a gradient-based inverse
solver to obtain the missing boundary conditions based on the
readings of internal thermocouples. The results show that the method
is very sensitive to measurement errors, and becomes unstable when
small time steps are used. The artificial neural networks are shown to
be capable of capturing the whole thermal history on the run-out
table, but are not very effective in restoring the detailed behavior of
the boundary conditions. Also, they behave poorly in nonlinear cases
and where the boundary condition profile is different.
GA and PSO are more effective in finding a detailed
representation of the time-varying boundary conditions, as well as in
nonlinear cases. However, their convergence takes longer. A
variation of the basic PSO, called CRPSO, showed the best
performance among the three versions. Also, PSO proved to be
effective in handling noisy data, especially when its performance
parameters were tuned. An increase in the self-confidence parameter
was also found to be effective, as it increased the global search
capabilities of the algorithm. RPSO was the most effective variation
in dealing with noise, closely followed by CRPSO. The latter
variation is recommended for inverse heat conduction problems, as it
combines the efficiency and effectiveness required by these
problems.
Abstract: In this paper, the problem of steady laminar boundary
layer flow and heat transfer over a permeable exponentially
stretching/shrinking sheet with generalized slip velocity is
considered. The similarity transformations are used to transform the
governing nonlinear partial differential equations to a system of
nonlinear ordinary differential equations. The transformed equations
are then solved numerically using the bvp4c function in MATLAB.
Dual solutions are found for a certain range of the suction and
stretching/shrinking parameters. The effects of the suction parameter,
stretching/shrinking parameter, velocity slip parameter, critical shear
rate and Prandtl number on the skin friction and heat transfer
coefficients as well as the velocity and temperature profiles are
presented and discussed.
Abstract: This paper presents development results of the method
of seismoacoustic activity monitoring based on usage vibrosensitive
properties of optical fibers. Analysis of Rayleigh backscattering
radiation parameters changes, which take place due to microscopic
seismoacoustic impacts on the optical fiber, allows to determine
seismoacoustic emission sources positions and to identify their types.
Results of using this approach are successful for complex monitoring
of railways.
Abstract: The convective heat and mass transfer in nanofluid
flow through a porous media due to a permeable stretching sheet with
magnetic field, viscous dissipation, chemical reaction and Soret
effects are numerically investigated. Two types of nanofluids, namely
Cu-water and Ag-water were studied. The governing boundary layer
equations are formulated and reduced to a set of ordinary differential
equations using similarity transformations and then solved
numerically using the Keller box method. Numerical results are
obtained for the skin friction coefficient, Nusselt number and
Sherwood number as well as for the velocity, temperature and
concentration profiles for selected values of the governing
parameters. Excellent validation of the present numerical results has
been achieved with the earlier linearly stretching sheet problems in
the literature.
Abstract: Incineration of municipal solid waste (MSW) is one of
the key scopes in the global clean energy strategy. A computational
fluid dynamics (CFD) model was established in order to reveal these
features of the combustion process in a fixed porous bed of MSW.
Transporting equations and process rate equations of the waste bed
were modeled and set up to describe the incineration process,
according to the local thermal conditions and waste property
characters. Gas phase turbulence was modeled using k-ε turbulent
model and the particle phase was modeled using the kinetic theory of
granular flow. The heterogeneous reaction rates were determined
using Arrhenius eddy dissipation and the Arrhenius-diffusion
reaction rates. The effects of primary air flow rate and temperature in
the burning process of simulated MSW are investigated
experimentally and numerically. The simulation results in bed are
accordant with experimental data well. The model provides detailed
information on burning processes in the fixed bed, which is otherwise
very difficult to obtain by conventional experimental techniques.
Abstract: A model was constructed to predict the amount of
solar radiation that will make contact with the surface of the earth in
a given location an hour into the future. This project was supported
by the Southern Company to determine at what specific times during
a given day of the year solar panels could be relied upon to produce
energy in sufficient quantities. Due to their ability as universal
function approximators, an artificial neural network was used to
estimate the nonlinear pattern of solar radiation, which utilized
measurements of weather conditions collected at the Griffin, Georgia
weather station as inputs. A number of network configurations and
training strategies were utilized, though a multilayer perceptron with
a variety of hidden nodes trained with the resilient propagation
algorithm consistently yielded the most accurate predictions. In
addition, a modeled direct normal irradiance field and adjacent
weather station data were used to bolster prediction accuracy. In later
trials, the solar radiation field was preprocessed with a discrete
wavelet transform with the aim of removing noise from the
measurements. The current model provides predictions of solar
radiation with a mean square error of 0.0042, though ongoing efforts
are being made to further improve the model’s accuracy.
Abstract: In the past researchers have questioned the
effectiveness of ethics training in higher education. Also, there are
observations that support the view that ethical behaviour (range of
actions)/ethical decision making models used in the past make use of
vignettes to explain ethical behaviour. The understanding remains in
the perspective that these vignettes play a limited role in determining
individual intentions and not actions. Some authors have also agreed
that there are possibilities of differences in one’s intentions and
actions. This paper makes an attempt to fill those gaps by evaluating
real actions rather than intentions. In a way this study suggests the
use of an experiential methodology to explore Berlo’s model of
communication as an action along with orchestration of various
principles. To this endeavor, an attempt was made to use
conversational analysis in the pursuance of evaluating ethical
decision making behaviour among students and middle level
managers. The process was repeated six times with the set of an
average of 15 participants. Similarities have been observed in the
behaviour of students and middle level managers that calls for
understanding that both the groups of individuals have no cognizance
of their actual actions. The deliberations derived out of conversation
were taken a step forward for meta-ethical evaluations to portray a
clear picture of ethical behaviour among participants. This study
provides insights for understanding demonstrated unconscious human
behaviour which may fortuitously be termed both ethical and
unethical.
Abstract: Traditional document representation for classification
follows Bag of Words (BoW) approach to represent the term weights.
The conventional method uses the Vector Space Model (VSM) to
exploit the statistical information of terms in the documents and they
fail to address the semantic information as well as order of the terms
present in the documents. Although, the phrase based approach
follows the order of the terms present in the documents rather than
semantics behind the word. Therefore, a semantic concept based
approach is used in this paper for enhancing the semantics by
incorporating the ontology information. In this paper a novel method
is proposed to forecast the intraday stock market price directional
movement based on the sentiments from Twitter and money control
news articles. The stock market forecasting is a very difficult and
highly complicated task because it is affected by many factors such
as economic conditions, political events and investor’s sentiment etc.
The stock market series are generally dynamic, nonparametric, noisy
and chaotic by nature. The sentiment analysis along with wisdom of
crowds can automatically compute the collective intelligence of
future performance in many areas like stock market, box office sales
and election outcomes. The proposed method utilizes collective
sentiments for stock market to predict the stock price directional
movements. The collective sentiments in the above social media have
powerful prediction on the stock price directional movements as
up/down by using Granger Causality test.
Abstract: The arm length, hand length, hand breadth and middle
finger length of 1540 right-handed industrial workers of Haryana
state was used to assess the relationship between the upper limb
dimensions and stature. Initially, the data were analyzed using basic
univariate analysis and independent t-tests; then simple and multiple
linear regression models were used to estimate stature using SPSS
(version 17). There was a positive correlation between upper limb
measurements (hand length, hand breadth, arm length and middle
finger length) and stature (p < 0.01), which was highest for hand
length. The accuracy of stature prediction ranged from ± 54.897 mm
to ± 58.307 mm. The use of multiple regression equations gave better
results than simple regression equations. This study provides new
forensic standards for stature estimation from the upper limb
measurements of male industrial workers of Haryana (India). The
results of this research indicate that stature can be determined using
hand dimensions with accuracy, when only upper limb is available
due to any reasons likewise explosions, train/plane crashes, mutilated
bodies, etc. The regression formula derived in this study will be
useful for anatomists, archaeologists, anthropologists, design
engineers and forensic scientists for fairly prediction of stature using
regression equations.
Abstract: The main purpose of this paper is to determine the
applicability of the constitutional social rights in the so-called
horizontal relations, i.e. the relations between private entities.
Nowadays the constitutional rights are more and more often violated
by private entities and not only by the state. The private entities
interfere with the privacy of individuals, limit their freedom of
expression or disturb their peaceful gatherings. International
corporations subordinate individuals in a way which may limit their
constitutional rights. These new realities determine the new role of
the constitution in protecting human rights.
The paper will aim at answering two important questions. Firstly,
are the private entities obliged to respect the constitutional social
rights of other private entities and can they be liable for violation of
these rights? Secondly, how the constitutional social rights can
receive horizontal effect? Answers to these questions will have a
significant meaning for the popularisation of the practice of applying
the Constitution among the citizens as well as for the courts which
settle disputes between them.
Abstract: A three-dimensional numerical model of
thermoelectric generator (TEG) modules attached to a large chimney
plate is proposed and solved numerically using a control volume based
finite difference formulation. The TEG module consists of a
thermoelectric generator, an elliptical pin-fin heat sink, and a cold
plate for water cooling. In the chimney, the temperature of flue gases is
450-650K. Although the TEG hot-side temperature and thus the
electric power output can be increased by inserting an elliptical pin-fin
heat sink into the chimney tunnel to increase the heat transfer area, the
pin fin heat sink would cause extra pumping power at the same time.
The main purpose of this study is to analyze the effects of geometrical
parameters on the electric power output and chimney pressure drop
characteristics. The effects of different operating conditions, including
various inlet velocities (Vin= 1, 3, 5 m/s), inlet temperatures (Tgas = 450,
550, 650K) and different fin height (0 to 150 mm) are discussed in
detail. The predicted numerical data for the power vs. current (P-I)
curve are in good agreement (within 11%) with the experimental data.
Abstract: Parabolic solar trough systems have seen limited
deployments in cold northern climates as they are more suitable for
electricity production in southern latitudes. A numerical dynamic
model is developed to simulate troughs installed in cold climates and
validated using a parabolic solar trough facility in Winnipeg. The
model is developed in Simulink and will be utilized to simulate a trigeneration
system for heating, cooling and electricity generation in
remote northern communities. The main objective of this simulation
is to obtain operational data of solar troughs in cold climates and use
the model to determine ways to improve the economics and address
cold weather issues.
In this paper the validated Simulink model is applied to simulate a
solar assisted absorption cooling system along with electricity
generation using Organic Rankine Cycle (ORC) and thermal storage.
A control strategy is employed to distribute the heated oil from solar
collectors among the above three systems considering the
temperature requirements. This modelling provides dynamic
performance results using measured meteorological data recorded
every minute at the solar facility location. The purpose of this
modeling approach is to accurately predict system performance at
each time step considering the solar radiation fluctuations due to
passing clouds. Optimization of the controller in cold temperatures is
another goal of the simulation to for example minimize heat losses in
winter when energy demand is high and solar resources are low.
The solar absorption cooling is modeled to use the generated heat
from the solar trough system and provide cooling in summer for a
greenhouse which is located next to the solar field.
The results of the simulation are presented for a summer day in
Winnipeg which includes comparison of performance parameters of
the absorption cooling and ORC systems at different heat transfer
fluid (HTF) temperatures.
Abstract: In this paper, the exergy analysis of vapor absorption
refrigeration system using LiBr-H2O as working fluid is carried out
with the modified Gouy-Stodola approach rather than the classical
Gouy-Stodola equation and effect of varying input parameters is also
studied on the performance of the system. As the modified approach
uses the concept of effective temperature, the mathematical
expressions for effective temperature have been formulated and
calculated for each component of the system. Various constraints and
equations are used to develop program in EES to solve these
equations. The main aim of this analysis is to determine the
performance of the system and the components having major
irreversible loss. Results show that exergy destruction rate is
considerable in absorber and generator followed by evaporator and
condenser. There is an increase in exergy destruction in generator,
absorber and condenser and decrease in the evaporator by the
modified approach as compared to the conventional approach. The
value of exergy determined by the modified Gouy-Stodola equation
deviates maximum i.e. 26% in the generator as compared to the
exergy calculated by the classical Gouy-Stodola method.
Abstract: This study analyzes the innovative orientation of the
Croatian entrepreneurs. Innovative orientation is represented by the
perceived extent to which an entrepreneur’s product or service or
technology is new, and no other businesses offer the same product.
The sample is extracted from the GEM Croatia Adult Population
Survey dataset for the years 2003-2013. We apply descriptive
statistics, t-test, Chi-square test and logistic regression. Findings
indicate that innovative orientations vary with personal, firm, meso
and macro level variables, and between different stages in
entrepreneurship process. Significant predictors are occupation of the
entrepreneurs, size of the firm and export aspiration for both early
stage and established entrepreneurs. In addition, fear of failure,
expecting to start a new business and seeing an entrepreneurial career
as a desirable choice are predictors of innovative orientation among
early stage entrepreneurs.
Abstract: Today’s VLSI networks demands for high speed. And
in this work the compact form mathematical model for current mode
signalling in VLSI interconnects is presented.RLC interconnect line
is modelled using characteristic impedance of transmission line and
inductive effect. The on-chip inductance effect is dominant at lower
technology node is emulated into an equivalent resistance. First order
transfer function is designed using finite difference equation, Laplace
transform and by applying the boundary conditions at the source and
load termination. It has been observed that the dominant pole
determines system response and delay in the proposed model. The
novel proposed current mode model shows superior performance as
compared to voltage mode signalling. Analysis shows that current
mode signalling in VLSI interconnects provides 2.8 times better
delay performance than voltage mode. Secondly the damping factor
of a lumped RLC circuit is shown to be a useful figure of merit.
Abstract: Applications of the Hausdorff space and its mappings
into tangent spaces are outlined, including their fractal dimensions
and self-similarities. The paper details this theory set up and further
describes virtualizations and atomization of manufacturing processes.
It demonstrates novel concurrency principles that will guide
manufacturing processes and resources configurations. Moreover,
varying levels of details may be produced by up folding and breaking
down of newly introduced generic models. This choice of layered
generic models for units and systems aspects along specific aspects
allows research work in parallel to other disciplines with the same
focus on all levels of detail. More credit and easier access are granted
to outside disciplines for enriching manufacturing grounds. Specific
mappings and the layers give hints for chances for interdisciplinary
outcomes and may highlight more details for interoperability
standards, as already worked on the international level. The new rules
are described, which require additional properties concerning all
involved entities for defining distributed decision cycles, again on the
base of self-similarity. All properties are further detailed and assigned
to a maturity scale, eventually displaying the smartness maturity of a
total shopfloor or a factory. The paper contributes to the intensive
ongoing discussion in the field of intelligent distributed
manufacturing and promotes solid concepts for implementations of
Cyber Physical Systems and the Internet of Things into
manufacturing industry, like industry 4.0, as discussed in German-speaking
countries.
Abstract: This paper attempts to define the validity domain of
LSDP (Loop Shaping Design Procedure) controller system, by
determining the suitable uncertainty region, so that linear system be
stable. Indeed the LSDP controller cannot provide stability for any
perturbed system. For this, we will use the gap metric tool that is
introduced into the control literature for studying robustness
properties of feedback systems with uncertainty. A 2nd order electric
linear system example is given to define the validity domain of LSDP
controller and effectiveness gap metric.
Abstract: Real bronchial tree is very complicated piping system.
Analysis of flow and pressure losses in this system is very difficult.
Due to the complex geometry and the very small size in the lower
generations is examination by CFD possible only in the central part
of bronchial tree. For specify the pressure losses of lower generations
is necessary to provide a mathematical equation. Determination of
mathematical formulas for calculation of pressure losses in the real
lungs is time consuming and inefficient process due to its complexity
and diversity. For these calculations is necessary to slightly simplify
the geometry of lungs (same cross-section over the length of
individual generation) or use one of the idealized models of lungs
(Horsfield, Weibel). The article compares the values of pressure
losses obtained from CFD simulation of air flow in the central part of
the real bronchial tree with the values calculated in a slightly
simplified real lungs by using a mathematical relationship derived
from the Bernoulli and continuity equations. The aim of the article is
to analyse the accuracy of the analytical method and its possibility of
use for the calculation of pressure losses in lower generations, which
is difficult to solve by numerical method due to the small geometry.
Abstract: This paper reports the worldwide status of building
information modeling (BIM) adoption from the perspectives of the
engagement level, the Hype Cycle model, the technology diffusion
model, and BIM services. An online survey was distributed, and 156
experts from six continents responded. Overall, North America was
the most advanced continent, followed by Oceania and Europe.
Countries in Asia perceived their phase mainly as slope of
enlightenment (mature) in the Hype Cycle model. In the technology
diffusion model, the main BIM-users worldwide were “early majority”
(third phase), but those in the Middle East/Africa and South America
were “early adopters” (second phase). In addition, the more advanced
the country, the more number of BIM services employed in general. In
summary, North America, Europe, Oceania, and Asia were advancing
rapidly toward the mature stage of BIM, whereas the Middle
East/Africa and South America were still in the early phase. The
simple indexes used in this study may be used to track the worldwide
status of BIM adoption in long-term surveys.
Abstract: Nature is the immense gifted source for solving
complex problems. It always helps to find the optimal solution to
solve the problem. Mobile Ad Hoc NETwork (MANET) is a wide
research area of networks which has set of independent nodes. The
characteristics involved in MANET’s are Dynamic, does not depend
on any fixed infrastructure or centralized networks, High mobility.
The Bio-Inspired algorithms are mimics the nature for solving
optimization problems opening a new era in MANET. The typical
Swarm Intelligence (SI) algorithms are Ant Colony Optimization
(ACO), Artificial Bee Colony (ABC), Particle Swarm Optimization
(PSO), Modified Termite Algorithm, Bat Algorithm (BA), Wolf
Search Algorithm (WSA) and so on. This work mainly concentrated
on nature of MANET and behavior of nodes. Also it analyses various
performance metrics such as throughput, QoS and End-to-End delay
etc.