Abstract: In the present study, we have synthesized Cr and Fe
doped zinc oxide (ZnO) nanostructures (Zn1-δCraFebO; where δ = a +
b = 20%, a = 5, 6, 8 & 10% and b = 15, 14, 12 & 10%) via sol-gel
method at different doping concentrations. The synthesized samples
were characterized for structural properties by X-ray diffractrometer
and field emission scanning electron microscope and the optical
properties were carried out through photoluminescence and UVvisible
spectroscopy. The particle size calculated through field
emission scanning electron microscope varies from 41 to 96 nm for
the samples synthesized at different doping concentrations. The
optical band gaps calculated through UV-visible spectroscopy are
found to be decreasing from 3.27 to 3.02 eV as the doping
concentration of Cr increases and Fe decreases.
Abstract: Multiwall carbon nanotubes, prepared by chemical
vapor deposition, have an average diameter of 60-100 nm as shown
by High Resolution Transmittance Electron Microscope, HR-TEM.
The Multiwall carbon nanotubes (MWCNTs) were further
characterized using X-ray Diffraction and Raman Spectroscopy.
Mercury uptake capacity of MWCNTs was studied using batch
adsorption method at different concentration ranges up to 150 ppm.
Mercury concentration (before and after the treatment) was measured
using cold vapor atomic absorption spectroscopy. The effect of time,
concentration, pH and adsorbent dose were studied. MWCNT were
found to perform complete absorption in the sub-ppm concentrations
(parts per billion levels) while for high concentrations, the adsorption
efficiency was 92% at the optimum conditions; 0.1 g of the adsorbent
at 150 ppm mercury (II) solution. The adsorption of mercury on
MWCNTs was found to follow the Freundlich adsorption isotherm
and the pseudo-second order kinetic model.
Abstract: Fuzzy systems have been successfully used for
exchange rate forecasting. However, fuzzy system is very confusing
and complex to be designed by an expert, as there is a large set of
parameters (fuzzy knowledge base) that must be selected, it is not a
simple task to select the appropriate fuzzy knowledge base for an
exchange rate forecasting. The researchers often look the effect of
fuzzy knowledge base on the performances of fuzzy system
forecasting. This paper proposes a genetic fuzzy predictor to forecast
the future value of daily US Dollar/Euro exchange rate time’s series.
A range of methodologies based on a set of fuzzy predictor’s which
allow the forecasting of the same time series, but with a different
fuzzy partition. Each fuzzy predictor is built from two stages, where
each stage is performed by a real genetic algorithm.
Abstract: The phased-array ultrasound transducer types are
utilities for medical ultrasonography as well as optical imaging.
However, their discontinuity characteristic limits the applications due
to the artifacts contaminated into the reconstructed images. Because
of the effects of the ultrasound pressure field pattern to the echo
ultrasonic waves as well as the optical modulated signal, the side
lobes of the focused ultrasound beam induced by discontinuity of the
phased-array ultrasound transducer might the reason of the artifacts.
In this paper, a simple method in approach of numerical simulation
was used to investigate the limitation of discontinuity of the elements
in phased-array ultrasound transducer and their effects to the
ultrasound pressure field. Take into account the change of ultrasound
pressure field patterns in the conditions of variation of the pitches
between elements of the phased-array ultrasound transducer, the
appropriated parameters for phased-array ultrasound transducer
design were asserted quantitatively.
Abstract: The aim of present study was to monitor the presence
of Trichodina sp. in Rainbow trout, Oncorhynchus mykiss collected
from various fish farms in the western provinces of Iran during
January, 2013- January, 2014. Out of 675 sampled fish 335, (49.16%)
were infested with Trichodina. The highest prevalence was observed
in the spring and winter followed by autumn and summer. In general,
the intensity of infection was low except in cases where outbreaks of
Trichodiniasis endangered the survival of fish in some ponds. In light
infestation Trichodina is usually present on gills, fins and skin of
apparently healthy fish. Clinical signs of Trichodiniasis only appear
on fish with heavy infections and cases of moderate ones that are
usually exposed to one or more stress factors including, rough
handling during transportation from ponds, overcrowdness,
malnutrition, high of free ammonia and low of oxygen concentration.
Clinical signs of Trichodiniasis in sampled fish were sluggish
movement, loss of appetite, black coloration, necrosis and ulcer on
different parts of the body, detached scales and excessive
accumulation of mucous in gill pouches. The most obvious
histopathological changes in diseased fish were sloughing of the
epidermal layer, aggregation of leucocytes and melanine-carrying
cells (between the dermis and hypodermis) and proliferative changes
including hyperplasia and hypertrophy of the epithelial lining cells of
gill filaments which resulted in fusion of secondary lamellae. Control
of Trichodiniasis, has been achieved by formalin bath treatment at a
concentration of 250 ppm for one hour.
Abstract: Multispectral screening systems are becoming more
popular because of their very interesting properties and applications.
One of the most significant applications of multispectral screening
systems is prevention of terrorist attacks. There are many kinds of
threats and many methods of detection. Visual detection of objects
hidden under clothing of a person is one of the most challenging
problems of threats detection. There are various solutions of the
problem; however, the most effective utilize multispectral
surveillance imagers. The development of imaging devices and
exploration of new spectral bands is a chance to introduce new
equipment for assuring public safety. We investigate the possibility
of long lasting detection of potentially dangerous objects covered
with various types of clothing. In the article we present the results of
comparative studies of passive imaging in three spectrums – visible,
infrared and terahertz.
Abstract: The objectives of this study is to investigate the
existence of the sticky cost behavior of firms listed in the Indonesia
Stock Exchange (IDX) and to find evidence on the effects of sticky
operating expenses (SG&A expenses) on profitability of firms. For
the first objective, this study finds that the sticky cost behavior does
exist. For the second objective, this study finds that the stickier the
operating expenses the lesser future profitability of the firms. This
study concludes that sticky cost affects negatively to the performance
and, therefore, firms should include flexibility in designing the cost
structure of their firms.
Abstract: Recently, an increasing number of researchers have
been focusing on working out realistic solutions to sustainability
problems. As sustainability issues gain higher importance for
organisations, the management of such decisions becomes critical.
Knowledge representation is a fundamental issue of complex
knowledge based systems. Many types of sustainability problems
would benefit from models based on experts’ knowledge. Cognitive
maps have been used for analyzing and aiding decision making. A
cognitive map can be made of almost any system or problem. A
fuzzy cognitive map (FCM) can successfully represent knowledge
and human experience, introducing concepts to represent the essential
elements and the cause and effect relationships among the concepts to
model the behaviour of any system. Integrated waste management
systems (IWMS) are complex systems that can be decomposed to
non-related and related subsystems and elements, where many factors
have to be taken into consideration that may be complementary,
contradictory, and competitive; these factors influence each other and
determine the overall decision process of the system. The goal of the
present paper is to construct an efficient IWMS which considers
various factors. The authors’ intention is to propose an expert based
system design approach for implementing expert decision support in
the area of IWMSs and introduces an appropriate methodology for
the development and analysis of group FCM. A framework for such a
methodology consisting of the development and application phases is
presented.
Abstract: A noble low NOx combustion technology, based on
partial oxidation combustion concept in a fuel rich combustion zone, is
successfully applied in this research. The burner is designed such that
a portion of fuel is heated and pre-vaporized in the furnace then
injected into a fuel rich combustion zone so that a partial oxidation
reaction occurs. The effects of equivalence ratio, thermal load, and
fuel distribution ratio on the emissions of NOx and CO are
experimentally investigated. This newly developed combustion
technology showed very low NOx emission level, about 12 ppm, when
light oil is used as a fuel.
Abstract: The North-eastern part of India, which receives
heavier rainfall than other parts of the subcontinent, is of great
concern now-a-days with regard to climate change. High intensity
rainfall for short duration and longer dry spell, occurring due to
impact of climate change, affects river morphology too. In the present
study, an attempt is made to delineate the North-eastern region of
India into some homogeneous clusters based on the Fuzzy Clustering
concept and to compare the resulting clusters obtained by using
conventional methods and nonconventional methods of clustering.
The concept of clustering is adapted in view of the fact that, impact
of climate change can be studied in a homogeneous region without
much variation, which can be helpful in studies related to water
resources planning and management. 10 IMD (Indian Meteorological
Department) stations, situated in various regions of the North-east,
have been selected for making the clusters. The results of the Fuzzy
C-Means (FCM) analysis show different clustering patterns for
different conditions. From the analysis and comparison it can be
concluded that nonconventional method of using GCM data is
somehow giving better results than the others. However, further
analysis can be done by taking daily data instead of monthly means to
reduce the effect of standardization.
Abstract: In this paper, the effect of WC-12Co particle
temperature in HVOF thermal spraying process on the coating
thickness has been studied. The statistical results show that the spray
distance and oxygen-to-fuel ratio are effective factors on particle
characterization and thickness of HVOF thermal spraying coatings.
Spray Watch diagnostic system, scanning electron microscopy
(SEM), X-ray diffraction and thickness measuring system were used
for this purpose.
Abstract: This paper explores the effects of gamification on
lower secondary school students’ motivation and engagement in the
classroom. Two-group posttest-only experimental design were
employed to study the influence of gamification teaching method
(GTM) when compared with conventional teaching method (CTM)
on 60 lower secondary school students. The Student Engagement
Instrument (SEI) and Intrinsic Motivation Inventory (IMI) were used
to assess students’ intrinsic motivation and engagement level towards
the respective teaching method. Finding indicates that students who
completed the GTM lesson were significantly higher in intrinsic
motivation to learn than those from the CTM. Although the result
were insignificant and only marginal difference in the engagement
mean, GTM still show better potential in raising student’s
engagement in class when compared with CTM. This finding proves
that the GTM is likely to solve the current issue of low motivation to
learn and low engagement in class among lower secondary school
students in Malaysia. On the other hand, despite being not significant,
higher mean indicates that CTM positively contribute to higher peer
support for learning and better teacher and student relationship when
compared with GTM. As a conclusion, gamification approach is
flexible and can be adapted into many learning content to enhance the
intrinsic motivation to learn and to some extent, encourage better
student engagement in class.
Abstract: This research aims to investigate callus induction,
somatic embryogenesis and indirect plant regeneration of Crassula
ovata (Mill.) Druce – the famous ornamental plant. Experiment no.1:
Callus induction was obtained from leaf and stem explants on
Murashige and Skoog (MS) medium supplemented with various plant
growth regulators (PGRs). Effects of different PGRs, plant
regeneration and subsequent plantlet conversion were also assessed.
Indirect plant regeneration was achieved from the callus of stem
explants by the addition of 1.5 mg/L Kinetin (KN) alone. Best shoot
induction was achieved (6.5 shoots/per explant) after 60 days. For
successful rooting, regenerated plantlets were sub-cultured on the
same MS media supplemented with 1.5 mg/L KN alone. The rooted
plantlets were acclimatized and the survival rate was 90%.
Experiment no.2: Results revealed that 0.5 mg/L 2,4-D alone and in
combination with 1.0 mg/L 6-Benzyladenine (BA) gave 89.8% callus
from the stem explants as compared to leaf explants. Callus
proliferation and somatic embryo formation were also evaluated by
‘Double Staining Method’ and different stages of somatic
embryogenesis were revealed by scanning electron microscope. Full
Strength MS medium produced the highest number (49.6%) of
cotyledonary stage somatic embryos (SEs). Mature cotyledonary
stage SEs developed into plantlets after 12 weeks of culture. Wellrooted
plantlets were successfully acclimatized at the survival rate of
85%. Indirectly regenerated plants did not show any detectable
variation in morphological and growth characteristics when
compared with the donor plant.
Abstract: The study was conducted to produce case studies from
the Malaysian public universities stands point East Coast of
Malaysia. The aim of this study is to analyze the effects of
knowledge management on human capital toward organizational
innovation. The focus point of this study is on the management
member in the faculties of these three Malaysian Public Universities
in the East Coast state of Peninsular Malaysia. In this case,
respondents who agreed to further participate in the research will be
invited to a one-hour face-to-face semi-structured, in-depth interview.
As a result, the sample size for this study was 3 deans of Faculty of
Management. Lastly, this study tries to recommend the framework of
organizational innovation in Malaysian Public Universities.
Abstract: The study was conducted to evaluate the efficiency of
Garlic and Chili combination solution on control of insect pests in
cabbage crop. The solution was sprayed at different intervals after
transplanting. The efficiency of Garlic and chili combination solution
on cabbage insect pests was measured. Results revealed that Garlic
and chili combination solution was the effectively reduced cabbage
insect pests. On other hand, the spray solution not only reduced the
number of days required for the cabbage growth but also greatly
enhanced the leaf number, head diameter, head weight, and quality of
cabbage. Garlic and chili combination solution have positive effects
on pests reduction and improve growth, yield and quality of cabbage
vegetable.
Abstract: Ancillary services are support services which are
essential for humanizing and enhancing the reliability and security of
the electric power system. Reactive power ancillary service is one of
the important ancillary services in a restructured electricity market
which determines the cost of supplying ancillary services and finding
of how this cost would change with respect to operating decisions.
This paper presents a new formation that can be used to minimize the
Independent System Operator (ISO)’s total payment for reactive
power ancillary service. The modified power flow tracing algorithm
estimates the availability of reserve reactive power for ancillary
service. In order to find optimum reactive power dispatch,
Biogeography based optimization method (BPO) is proposed. Market
Reactive Clearing Price (MRCP) is then estimated and it encourages
generator companies (GENCOs) to participate in an ancillary service.
Finally, optimal weighting factor and real time utilization factor of
reactive power give the minimum ISO’s total payment. The
effectiveness of proposed design is verified using IEEE 30 bus
system.
Abstract: In this paper the effect of wall waviness of side walls
in a two-dimensional wavy enclosure is numerically investigated.
Two vertical wavy walls and straight top wall are kept isothermal and
the bottom wall temperature is higher and spatially varying with
cosinusoidal temperature distribution. A computational code based on
Finite-volume approach is used to solve governing equations and
SIMPLE method is used for pressure velocity coupling. Test is
performed for several different numbers of undulations. The Prandtl
number was kept constant and the Ra number denotes that the flow is
laminar. Temperature and velocity fields are determined. Therefore,
according to the obtained results a correlation is proposed for average
Nusselt number as a function of number of side wall waves. The
results indicate that the Nusselt number is highly affected by number
of waves and increasing it decreases the wavy walls Nusselt number;
although the Nusselt number is not highly affected by surface
waviness when the number of undulations is below one.
Abstract: This paper presents a 4-DOF nonlinear model of a
cracked de Laval rotor-stator system derived based on Energy
Principles. The model has been used to simulate coupled torsionallateral
response of the faulty system with multiple parametric
excitations; rotor-stator-rub, a breathing transverse crack, eccentric
mass and an axial force. Nonlinearity of a “breathing” crack is
incorporated in the model using a simple hinge mechanism suitable
for a shallow crack. Response of the system while passing via its
critical speed with intermittent rotor-stator rub is analyzed. Effects of
eccentricity with phase and acceleration are investigated. Features of
crack, rub and eccentricity in vibration response are explored for
condition monitoring. The presence of a crack and rub are observable
in the power spectrum despite excitations by an axial force and rotor
unbalance. Obtained results are consistent with existing literature and
could be adopted into rotor condition monitoring strategies.
Abstract: Innovations not only contribute to competitiveness of
the company but have also positive effects on revenues. On average,
product innovations account to 14 percent of companies’ sales.
Innovation management has substantially changed during the last
decade, because of growing reliance on external partners. As a
consequence, a new task for purchasing arises, as firms need to
understand which suppliers actually do have high potential
contributing to the innovativeness of the firm and which do not.
Proper organization of the purchasing function is important since
for the majority of manufacturing companies deal with substantial
material costs which pass through the purchasing function. In the past
the purchasing function was largely seen as a transaction-oriented,
clerical function but today purchasing is the intermediate with supply
chain partners contributing to innovations, be it product or process
innovations. Therefore, purchasing function has to be organized
differently to enable firm innovation potential.
However, innovations are inherently risky. There are behavioral
risk (that some partner will take advantage of the other party),
technological risk in terms of complexity of products and processes
of manufacturing and incoming materials and finally market risks,
which in fact judge the value of the innovation. These risks are
investigated in this work. Specifically, technological risks which deal
with complexity of the products, and processes will be investigated
more thoroughly. Buying components or such high edge technologies
necessities careful investigation of technical features and therefore is
usually conducted by a team of experts. Therefore it is hypothesized
that higher the technological risk, higher will be the centralization of
the purchasing function as an interface with other supply chain
members.
Main contribution of this research lies is in the fact that analysis
was performed on a large data set of 1493 companies, from 25
countries collected in the GMRG 4 survey. Most analyses of
purchasing function are done by case study analysis of innovative
firms. Therefore this study contributes with empirical evaluations that
can be generalized.
Abstract: Urban greenery remains the bastion of urban
landscape and a key to sustainable development due to its integral
connections to the general health and wellbeing of urban residents.
However, in an era of rapid urbanisation, recent studies indicate that
urban greenery, especially ecologically sensitive areas, in many
African cities is becoming increasingly depleted. Given the scale and
rate of natural and anthropogenic change, effective management of
urban greenery as the ultimate goal of restoring depleting urban
landscapes is urgent. This review advocates for an urban resilience
model to managing urban greenery.