Abstract: A new small–scale test rig developed for rolling
contact fatigue (RCF) investigations in wheel–rail material. This
paper presents the scaling strategy of the rig based on dimensional
analysis and mechanical modelling. The new experimental rig is
indeed a spinning frame structure with multiple wheel components
over a fixed rail-track ring, capable of simulating continuous wheelrail
contact in a laboratory scale. This paper describes the
dimensional design of the rig, to derive its overall scaling strategy
and to determine the key elements’ specifications. Finite element
(FE) modelling is used to simulate the mechanical behavior of the rig
with two sample scale factors of 1/5 and 1/7. The results of FE
models are compared with the actual railway system to observe the
effectiveness of the chosen scales. The mechanical properties of the
components and variables of the system are finally determined
through the design process.
Abstract: A single-phase closed thermosyphon has been
fabricated and experimented to utilize solar energy for water heating.
The working fluid of the closed thermosyphon is heated at the flatplate
collector and the hot water goes to the water tank due to density
gradient caused by temperature differences. This experimental work
was done using insulated water tank and insulated connecting pipe
between the tank and the flat-plate collector. From the collected data,
performance parameters such as instantaneous collector efficiency
and heat removal factor are calculated. In this study, the effects of
glazing were also observed. The water temperature rise and the
maximum instantaneous efficiency obtained from this experiment
with glazing using insulated water tank and insulated connecting pipe
are 17°C in a period of 5 hours and 60% respectively. Whereas the
water temperature rise and the maximum instantaneous efficiency
obtained from this experiment with glazing using non-insulated water
tank and non-insulated connecting pipe are 14°C in a period of 5
hours and 39% respectively.
Abstract: Hydrogenated amorphous carbon (a-C:H) films have
been synthesized by a radio frequency plasma enhanced chemical
vapor deposition (rf-PECVD) technique with different bias voltage
from 0.0 to -0.5 kV. The Raman spectra displayed the polymer-like
hydrogenated amorphous carbon (PLCH) film with 0.0 to -0.1 and
a-C:H films with -0.2 to -0.5 kV of bias voltages. The surface chemical
information of all films were studied by X-ray photoelectron
spectroscopy (XPS) technique, presented to C-C (sp2 and sp3) and C-O
bonds, and relative carbon (C) and oxygen (O) atomics contents. The
O contamination had affected on structure and optical properties. The
true density of PLCH and a-C:H films were characterized by X-ray
refractivity (XRR) method, showed the result as in the range of
1.16-1.73 g/cm3 that depending on an increasing of bias voltage. The
hardness was proportional to the true density of films. In addition, the
optical properties i.e. refractive index (n) and extinction coefficient (k)
of these films were determined by a spectroscopic ellipsometry (SE)
method that give formation to in 1.62-2.10 (n) and 0.04-0.15 (k)
respectively. These results indicated that the optical properties
confirmed the Raman results as presenting the structure changed with
applied bias voltage increased.
Abstract: This paper presents the electromagnetic interference
(EMI) shielding effectiveness of rice husk and carbon nanotubes
(RHCNTs) composites in the X-band region (8.2-12.4 GHz). The
difference weight ratio of carbon nanotubes (CNTs) were mix with
the rice husk. The rectangular waveguide technique was used to
measure the complex permittivity of the RHCNTs composites
materials. The complex permittivity is represented in terms of both
the real and imaginary parts of permittivity in X-band frequency. The
conductivity of RHCNTs shows increasing when the ratio of CNTs
mixture increases. The composites materials were simulated using
Computer Simulation Technology (CST) Microwave Studio
simulation software. The shielding effectiveness of RHCNTs and
pure rice husk was compared. The highest EMI SE of 30 dB is
obtained for RHCNTs composites of 10 wt % CNTs with 10mm
thickness.
Abstract: Aluminium and its alloys have excellent corrosion
resistant properties, ease of fabrication and high specific strength to
weight ratio. In this investigation an attempt has been made to study
the effect of different post weld heat treatment methods on the
mechanical and metallurgical properties of TIG welded joints of the
commercial aluminium alloy. Three different methods of post weld
heat treatments are solution heat treatment, artificial ageing and
combination of solution heat treatment and artificial aging are given
to TIG welded aluminium joints. Mechanical and metallurgical
properties of As welded joints of the aluminium alloys and post weld
heat treated joints of the aluminium alloys were examined.
Abstract: In structures, stress concentration is a factor of fatigue
fracture. Basically, the stress concentration is a phenomenon that
should be avoided. However, it is difficult to avoid the stress
concentration. Therefore, relaxation of the stress concentration is
important. The stress concentration arises from notches and circular
holes. There is a relaxation method that a composite patch covers a
notch and a circular hole. This relaxation method is used to repair
aerial wings, but it is not systematized. Composites are more
expensive than single materials. Accordingly, we propose the
relaxation method that a single material patch covers a notch and a
circular hole, and aim to systematize this relaxation method.
We performed FEA (Finite Element Analysis) about an object by
using a three-dimensional FEA model. The object was that a patch
adheres to a plate with a circular hole. And, a uniaxial tensile load acts
on the patched plate with a circular hole. In the three-dimensional FEA
model, it is not easy to model the adhesion layer. Basically, the yield
stress of the adhesive is smaller than that of adherents. Accordingly,
the adhesion layer gets to plastic deformation earlier than the adherents
under the yield load of adherents. Therefore, we propose the
three-dimensional FEA model which is applied a nonlinear elastic
region to the adhesion layer. The nonlinear elastic region was
calculated by a bilinear approximation. We compared the analysis
results with the tensile test results to confirm whether the analysis
model has usefulness. As a result, the analysis results agreed with the
tensile test results. And, we confirmed that the analysis model has
usefulness.
As a result that the three-dimensional FEA model was used to the
analysis, it was confirmed that an out-of-plane deformation occurred
to the patched plate with a circular hole. The out-of-plane deformation
causes stress increase of the patched plate with a circular hole.
Therefore, we investigated that the out-of-plane deformation affects
relaxation of the stress concentration in the plate with a circular hole
on this relaxation method. As a result, it was confirmed that the
out-of-plane deformation inhibits relaxation of the stress concentration
on the plate with a circular hole.
Abstract: In this paper, we have proposed a parallel IDS and
honeypot based approach to detect and analyze the unknown and
known attack taxonomy for improving the IDS performance and
protecting the network from intruders. The main theme of our
approach is to record and analyze the intruder activities by using both
the low and high interaction honeypots. Our architecture aims to
achieve the required goals by combing signature based IDS,
honeypots and generate the new signatures. The paper describes the
basic component, design and implementation of this approach and
also demonstrates the effectiveness of this approach to reduce the
probability of network attacks.
Abstract: Recently, there have been a lot of earthquakes in Japan.
It is necessary to promote seismic isolation devices for buildings. The
devices have been hardly diffused in attached houses, because the
devices are very expensive. We should develop a low-cost seismic
isolation device for detached houses. We suggested a new seismic
isolation device which uses a two-layer circular tube as a unit. If
hysteresis is produced in the two-layer circular tube under lateral
compression load, we think that the two-layer circular tube can have
energy absorbing capacity. It is necessary to contact the outer layer
and the inner layer to produce hysteresis. We have previously reported
how the inner layer comes in contact with the outer layer from a
perspective of analysis used mechanics of materials. We have clarified
that the inner layer comes in contact with the outer layer under a lateral
compression load. In this paper, we explored contact area between the
outer layer and the inner layer under a lateral compression load by
using FEA. We think that changing the inner layer’s thickness is
effective in increase the contact area. In order to change the inner
layer’s thickness, we changed the shape of the inner layer. As a result,
the contact area changes depending on the inner layer’s thickness.
Additionally, we experimented to check whether hysteresis occurs in
fact. As a consequence, we can reveal hysteresis in the two-layer
circular tube under the condition.
Abstract: Kigelia africana (Lam.) Benth. (Bignoniaceae) is a
reputed traditional remedy for various human ailments such as skin
diseases, microbial infections, melanoma, stomach troubles,
metabolic disorders, malaria and general pains. In spite of the fruit
being widely used for purposes related to its antibacterial and
antifungal properties, the chemical constituents associated with the
activity have not been fully identified. To elucidate the active
principles, we evaluated the antimicrobial activity of fruit extracts
and purified fractions against Staphylococcus aureus, Enterococcus
faecalis, Moraxella catarrhalis, Escherichia coli, Candida albicans
and Candida tropicalis. Shade-dried fruits were powdered and
extracted with hydroalcoholic (1:1) mixture by soaking at room
temperature for 72 h. The crude extract was further fractionated by
column chromatography, with successive elution using hexane,
dichloromethane, ethyl acetate, acetone and methanol. The
dichloromethane and ethyl acetate fractions were combined and
subjected to column chromatography to furnish a wax and oil from
the eluates of 20% and 40% ethyl acetate in hexane, respectively. The
GC-MS and GC×GC-MS results revealed that linoleic acid, linolenic
acid, palmitic acid, arachidic acid and stearic acid were the major
constituents in both oil and wax. The crude hydroalcoholic extract
exhibited the strongest activity with MICs of 0.125-0.5 mg/mL,
followed by the ethyl acetate (MICs = 0.125-1.0 mg/mL),
dichloromethane (MICs = 0.250-2.0 mg/mL), hexane (MICs = 0.25-
2.0 mg/mL), acetone (MICs = 0.5-2.0 mg/mL) and methanol (MICs =
1.0-2.0 mg/mL), whereas the wax (MICs = 2.0-4.0 mg/mL) and oil
(MICs = 4.0-8.0 mg/mL) showed poor activity. The study concludes
that synergistic interactions of chemical constituents could be
responsible for the antimicrobial activity of K. africana fruits, which
needs a more holistic approach to understand the mechanism of its
antimicrobial activity.
Abstract: The study identified the socio-economic and
demographic factors of both married and unmarried females in third
world countries. Almost all the countries have same problems but we
have selected Pakistan as a sample country. The main purpose of this
study was to examine which factors forced women to participate in
labor market. So the best technique of data collection was survey of
both married and unmarried females between the ages of 20 to 49.
Two models (probit and logit) were used to analyze the factors which
effect on FLFP. The result showed that some factors e.g. age;
education and marital status have significant effect on FLFP. The
findings showed that educated women and those who belong to joint
families are more participate because of financial pressure.
Abstract: In this paper, the effect of admixtures on the tensional
strength of concrete in Urmia-lake water have been investigated. We
made different types of concretes with the ratio of w/c and replaced
different percentages of micro-silica, air-entraining, super plasticizer,
corrosion-inhibiting, and caulk with two types of cement I and II as
well as investigating in both ordinary water and Urmia-lake water.
The tensional strength was investigated on these samples.
Abstract: Cement-based grouts has been used successfully to
repair cracks in many concrete structures such as bridges, tunnels,
buildings and to consolidate soils or rock foundations. In the present
study the rheological characterization of cement grout with
water/binder ratio (W/B) is fixed at 0.5. The effect of the replacement
of cement by bentonite (2 to 10% wt) in presence of superplasticizer
(0.5% wt) was investigated. Several rheological tests were carried out
by using controlled-stress rheometer equipped with vane geometry in
temperature of 20°C. To highlight the influence of bentonite and
superplasticizer on the rheological behavior of grout cement, various
flow tests in a range of shear rate from 0 to 200 s-1 were observed.
Cement grout showed a non-Newtonian viscosity behavior at all
concentrations of bentonite. Three parameter model Herschel-
Bulkley was chosen for fitting of experimental data. Based on the
values of correlation coefficients of the estimated parameters, The
Herschel-Bulkley law model well described the rheological behavior
of the grouts. Test results showed that the dosage of bentonite
increases the viscosity and yield stress of the system and introduces
more thixotropy. While the addition of both bentonite and
superplasticizer with cement grout improve significantly the fluidity
and reduced the yield stress due to the action of dispersion of SP.
Abstract: In order to study the effect of drought stress on grain
yield, yield components and associated traits of durum wheat
cultivars, an experiment was done as split plot arrangement using
randomized complete block design with three replications in Ilam
province, Iran in 2009-2010 cropping season. Different levels of
irrigation (Full irrigation, drought stress at stem elongation,
Flowering and grain formation stages) were considered as a main plot
and three durum wheat cultivars (Yavaros, Seimareh and Karkheh)
were assigned as a sub plot. The results showed that drought stress
was significant on grain yield, spike.m-2, grain. Spike-1, 1000-grain
weight, biological yield, harvest index and protein content. Drought
stress at all stages caused a loss in grain yield and its components.
Full irrigation had the highest grain yield and yield components.
Drought stress at stem elongation, flowering and grain formation
stages caused a reduction in spike.m-2, grain.spike-1 and 1000-grain
weight, respectively. Protein content was significantly affected by
drought stress. The highest protein content was obtained from
drought stress at grain formation stage. Cultivars had an influence on
grain yield and yield components. Yavaros and Seimareh cultivars
had the highest and lowest grain yield, respectively. Interaction effect
between drought stress and cultivar had a significant effect on grain
and yield components. Full irrigation and Yavaros cultivar had the
highest grain yield and drought stress at grain formation stage and
Seimareh cultivar had the lowest grain yield, respectively.
Abstract: The development of the agricultural sector in Ghana
has been reliant on the use of irrigation systems to ensure food
security. However, the manual operation of these systems has not
facilitated their maximum efficiency due to human limitations.
This paper seeks to address this problem by designing and
implementing an efficient, cost effective automated system which
monitors and controls the water flow of irrigation through
communication with an authorized operator via text messages. The
automatic control component of the system is timer based with an
Atmega32 microcontroller and a real time clock from the SM5100B
cellular module. For monitoring purposes, the system sends periodic
notification of the system on the performance of duty via SMS to the
authorized person(s). Moreover, the GSM based Irrigation
Monitoring and Control System saves time and labour and reduces
cost of operating irrigation systems by saving electricity usage and
conserving water.
Field tests conducted have proven its operational efficiency and
ease of assessment of farm irrigation equipment due to its costeffectiveness
and data logging capabilities.
Abstract: The current study explored the effect of economic
development, financial development and institutional quality on
environmental destruction in upper-middle income countries during
the time period of 1999-2011. The dependent variable is logarithm of
carbon dioxide emissions that can be considered as an index for
destruction or quality of the environment given to its effects on the
environment. Financial development and institutional development
variables as well as some control variables were considered. In order
to study cross-sectional correlation among the countries under study,
Pesaran and Friz test was used. Since the results of both tests show
cross-sectional correlation in the countries under study, seemingly
unrelated regression method was utilized for model estimation. The
results disclosed that Kuznets’ environmental curve hypothesis is
confirmed in upper-middle income countries and also, financial
development and institutional quality have a significant effect on
environmental quality. The results of this study can be considered by
policy makers in countries with different income groups to have
access to a growth accompanied by improved environmental quality.
Abstract: The main goal of this paper was evaluate the effect of
diets containing different levels of probiotic on performance and milk
composition of lactating cows.
Eight Holstein cows were distributed in two 4x4 Latin square. The
diets were based on corn silage, concentrate and the treatment (0, 3, 6
or 9 grams of probiotic/animal/day). It was evaluated the dry matter
intake of nutrients, milk yield and composition.
The use of probiotics did not affect the nutrient intake (p>0.05)
neither the daily milk production or corrected to 4% fat (p>0.05).
However, it was observed that there was a significant fall in milk
composition with higher levels of probiotics supplementation.
These results emphasize the need of further studies with different
experimental designs or improve the number of Latin square with
longer periods of adaptation.
Abstract: A finite difference/front tracking method is used to
study the motion of three-dimensional deformable drops suspended in
plane Poiseuille flow at non-zero Reynolds numbers. A parallel
version of the code was used to study the behavior of suspension on a
reasonable grid resolution (grids). The viscosity and density of drops
are assumed to be equal to that of the suspending medium. The effect
of the Reynolds number is studied in detail. It is found that drops
with small deformation behave like rigid particles and migrate to an
equilibrium position about half way between the wall and the
centerline (the Segre-Silberberg effect). However, for highly
deformable drops there is a tendency for drops to migrate to the
middle of the channel, and the maximum concentration occurs at the
centerline. The effective viscosity of suspension and the fluctuation
energy of the flow across the channel increases with the Reynolds
number of the flow.
Abstract: It’s an era of high competition, dynamism and
complexities which have forced organizations to change dramatically
due to rising customer expectations. Marketers are under constant
pressure to deliver finest to their customers. With the advent of
technology, marketers have identified latest advertising media
options to reach out to target audience. But the conventional ways of
print advertisements still holds a deeper penetration and coverage.
Various researchers and practitioners have studied the area of print
media advertising and have tried to identify and implement
advertisement effectiveness enablers. The purpose of this paper is to
suggest select enablers for print media in Indian context using an
integrated approach of review of literature and investigative
interviews with academicians and experts from the area of
advertising.
Abstract: Students’ achievement and motivation in learning
English in Malaysia is a worrying trend as it is lagging behind several
other countries in Asia. Thus, necessary actions have to be taken by
the parties concerned to overcome this problem. The purpose of this
research was to study the effects of drill and practice courseware on
students’ achievement and motivation in learning English language.
A multimedia courseware was developed for this purpose. The
independent variable was the drill and practice courseware while the
dependent variables were the students’ achievement and motivation.
Their achievement was measured using pre-test and post-test scores,
while motivation was measured using a questionnaire. A total of 60
students from three vernacular primary schools in a northern state in
Malaysia were randomly selected in this study. The findings indicate:
(1) a significant difference between the students’ pre-test and posttest
scores after using the courseware, (2) no significant difference in
the achievement score between male and female students after using
the courseware, (3) a significant difference in motivation score
between the female and the male students, and (4) while the female
students scored significantly higher than the male students in the
aspects of relevance, confidence and satisfaction, no significant
difference in terms of attention was observed between them. Overall,
the findings clearly indicate that although the female students are
significantly more motivated than their male students, they are
equally good in terms of achievement after learning from the
courseware. Through this study, the drill and practice courseware is
proven to influence the students’ learning and motivation.
Abstract: There are several methods to monitor software
projects and the objective for monitoring is to ensure that the
software projects are developed and delivered successfully. A
performance measurement is a method that is closely associated with
monitoring and it can be scrutinized by looking at two important
attributes which are efficiency and effectiveness both of which are
factors that are important for the success of a software project.
Consequently, a successful steering is achieved by monitoring and
controlling a software project via the performance measurement
criteria and metrics. Hence, this paper is aimed at identifying the
performance measurement criteria and the metrics for monitoring the
performance of a software project by using the Goal Question
Metrics (GQM) approach. The GQM approach is utilized to ensure
that the identified metrics are reliable and useful. These identified
metrics are useful guidelines for project managers to monitor the
performance of their software projects.