Abstract: This paper describes Nano-particle based Planar Laser
Scattering (NPLS) flow visualization of angled supersonic jets into a
supersonic cross flow based on the HYpersonic Low TEmperature
(HYLTE) nozzle which was widely used in DF chemical laser. In
order to investigate the non-reacting flowfield in the HYLTE nozzle, a
testing section with windows was designed and manufactured. The
impact of secondary fluids orifice separation on mixing was examined.
For narrow separation of orifices, the secondary fuel penetration
increased obviously compared to diluent injection, which means
smaller separation of diluent and fuel orifices would enhance the
mixing of fuel and oxidant. Secondary injections with angles of 30, 40
and 50 degrees were studied. It was found that the injectant
penetration increased as the injection angle increased, while the
interfacial surface area to entrain the freestream fluid is largest when
the injection angle is 40 degree.
Abstract: Anti-money laundering is commonly recognized as a
set of procedures, laws or regulations designed to reduce the practice
of generating income through illegal actions. In Malaysia, the
government and law enforcement agencies have stepped up their
capacities and efforts to curb money laundering since 2001. One of
these measures was the enactment of the Anti-Money Laundering
Act (AMLA) in 2001. The implementation costs on anti-money
laundering requirements (AMLR) can be burdensome to those who
are involved in enforcing them. The objective of this paper is to
explore the perceived effectiveness of AMLR from the enforcement
agencies- perspective. This is a preliminary study whose findings
will help to give direction for further AML research in Malaysia. In
addition, the results of this study provide empirical evidences on the
perceived effectiveness of AMLR prior to further investigations on
barriers and improvements of the implementation of the anti-money
laundering regime in Malaysia.
Abstract: Prior research evidenced that unimodal biometric
systems have several tradeoffs like noisy data, intra-class variations,
restricted degrees of freedom, non-universality, spoof attacks, and
unacceptable error rates. In order for the biometric system to be more
secure and to provide high performance accuracy, more than one
form of biometrics are required. Hence, the need arise for multimodal
biometrics using combinations of different biometric modalities. This
paper introduces a multimodal biometric system (MMBS) based on
fusion of whole dorsal hand geometry and fingerprints that acquires
right and left (Rt/Lt) near-infra-red (NIR) dorsal hand geometry (HG)
shape and (Rt/Lt) index and ring fingerprints (FP). Database of 100
volunteers were acquired using the designed prototype. The acquired
images were found to have good quality for all features and patterns
extraction to all modalities. HG features based on the hand shape
anatomical landmarks were extracted. Robust and fast algorithms for
FP minutia points feature extraction and matching were used. Feature
vectors that belong to similar biometric traits were fused using
feature fusion methodologies. Scores obtained from different
biometric trait matchers were fused using the Min-Max
transformation-based score fusion technique. Final normalized scores
were merged using the sum of scores method to obtain a single
decision about the personal identity based on multiple independent
sources. High individuality of the fused traits and user acceptability
of the designed system along with its experimental high performance
biometric measures showed that this MMBS can be considered for
med-high security levels biometric identification purposes.
Abstract: The rising price of fossil fuels, government incentives
and growing public aware-ness for the need to implement sustainable
energy supplies has resulted in a large in-crease in solar panel
installations across the country. For many sites the most eco-nomical
solar panel installation uses existing, southerly facing rooftops.
Adding solar panels to an existing roof typically means increased
loads that must be borne by the building-s structural elements. The
structural design professional is responsible for ensuring a new solar
panel installation is properly supported by an existing structure and
configured to maximize energy generation.
Abstract: Single crystals of Magnesium alloys such as pure Mg,
Mg-1Zn-0.5Y, Mg-0.1Y, and Mg-0.1Ce alloys were successfully
fabricated in this study by employing the modified Bridgman method.
To determine the exact orientation of crystals, pole figure
measurement using X-ray diffraction were carried out on each single
crystal. Hardness and compression tests were conducted followed by
subsequent recrysatllization annealing. Recrystallization kinetics of
Mg alloy single crystals has been investigated. Fabricated single
crystals were cut into rectangular shaped specimen and solution
treated at 400oC for 24 hrs, and then deformed in compression mode
by 30% reduction. Annealing treatment for recrystallization has been
conducted on these cold-rolled plates at temperatures of 300oC for
various times from 1 to 20 mins. The microstructure observation and
hardness measurement conducted on the recrystallized specimens
revealed that static recrystallization of ternary alloy single crystal was
very slow, while recrystallization behavior of binary alloy single
crystals appeared to be very fast.
Abstract: Purpose: To develop a method for automatic segmentation of adipose and muscular tissue in thighs from magnetic resonance images. Materials and methods: Thirty obese women were scanned on a Siemens Impact Expert 1T resonance machine. 1500 images were finally used in the tests. The developed segmentation method is a recursive and multilevel process that makes use of several concepts such as shaped histograms, adaptative thresholding and connectivity. The segmentation process was implemented in Matlab and operates without the need of any user interaction. The whole set of images were segmented with the developed method. An expert radiologist segmented the same set of images following a manual procedure with the aid of the SliceOmatic software (Tomovision). These constituted our 'goal standard'. Results: The number of coincidental pixels of the automatic and manual segmentation procedures was measured. The average results were above 90 % of success in most of the images. Conclusions: The proposed approach allows effective automatic segmentation of MRIs from thighs, comparable to expert manual performance.
Abstract: It is well known that metallic particles reduce the
reliability of Gas-Insulated Substation (GIS) equipments by initiating
partial discharge (PDs) that can lead to breakdown and complete
failure of GIS. This paper investigates the characteristics of PDs
caused by metallic particle adhering to the solid spacer. The PD
detection and measurement were carried out by using IEC 60270
method with particles of different sizes and at different positions on
the spacer surface. The results show that a particle of certain size at
certain position possesses a unique PD characteristic as compared to
those caused by particles of different sizes and/or at different
positions. Therefore PD characteristics may be useful for the particle
size and position identification.
Abstract: Today technological process makes possible surface
control of producing parts which is needful for product quality
guarantee. Geometrical structure of part surface includes form,
proportion, accuracy to shape, accuracy to size, alignment and
surface topography (roughness, waviness, etc.). All these parameters
are dependence at technology, production machine parameters,
material properties, but also at human, etc. Every parameters
approves at total part accuracy, it is means at accuracy to shape. One
of the most important accuracy to shape element is roundness. This
paper will be deals by comparison of roughness deviations at
coordination measuring machines and at special single purpose
machines. Will describing measuring by discreet method
(discontinuous) and scanning method (continuous) at coordination
measuring machines and confrontation with reference method using
at single purpose machines.
Abstract: The Pads have unique values of thermophysical
properties (THP) having important contribution over heat transfer
into the PCB structure.
Materials with high thermal diffusivity (TD) rapidly adjust their
temperature to that of their surroundings, because the HT is quick in
compare to their volumetric heat capacity (VHC).
In the paper is presenting the diffusivity tests (ASTM E1461 flash
method) for PCBs with different core materials. In the experiments,
the multilayer structure of PCBA was taken into consideration, an
equivalent property referring to each of experimental structure be
practically measured.
Concerning to entire structure, the THP emphasize the major
contribution of substrate in establishing of reflow soldering process
(RSP) heat transfer necessities. This conclusion offer practical
solution for heat transfer time constant calculation as function of
thickness and substrate material diffusivity with an acceptable error
estimation.
Abstract: The OTOP Entrepreneurship that used to create
substantial source of income for local Thai communities are now in a
stage of exigent matters that required assistances from public sectors
due to over Entrepreneurship of duplicative ideas, unable to adjust
costs and prices, lack of innovation, and inadequate of quality
control. Moreover, there is a repetitive problem of middlemen who
constantly corner the OTOP market. Local OTOP producers become
easy preys since they do not know how to add more values, how to
create and maintain their own brand name, and how to create proper
packaging and labeling. The suggested solutions to local OTOP
producers are to adopt modern management techniques, to find
knowhow to add more values to products and to unravel other
marketing problems. The objectives of this research are to study the
prevalent OTOP products management and to discover direction to
manage OTOP products to enhance the effectiveness of OTOP
Entrepreneurship in Nonthaburi Province, Thailand. There were 113
participants in this study. The research tools can be divided into two
parts: First part is done by questionnaire to find responses of the
prevalent OTOP Entrepreneurship management. Second part is the
use of focus group which is conducted to encapsulate ideas and local
wisdom. Data analysis is performed by using frequency, percentage,
mean, and standard deviation as well as the synthesis of several small
group discussions. The findings reveal that 1) Business Resources:
the quality of product is most important and the marketing of product
is least important. 2) Business Management: Leadership is most
important and raw material planning is least important. 3) Business
Readiness: Communication is most important and packaging is least
important. 4) Support from public sector: Certified from the
government is most important and source of raw material is the least
important.
Abstract: In this paper a computer system for electromagnetic
properties measurements is designed. The system employs Agilent
4294A precision impedance analyzer to measure the amplitude and
the phase of a signal applied over a tested biological tissue sample.
Measured by the developed computer system data could be used for
tissue characterization in wide frequency range from 40Hz to
110MHz. The computer system can interface with output devices
acquiring flexible testing process.
Abstract: True stress-strain curve of railhead steel is required to
investigate the behaviour of railhead under wheel loading through elasto-plastic Finite Element (FE) analysis. To reduce the rate of wear, the railhead material is hardened through annealing and
quenching. The Australian standard rail sections are not fully hardened and hence suffer from non-uniform distribution of the
material property; usage of average properties in the FE modelling can potentially induce error in the predicted plastic strains. Coupons
obtained at varying depths of the railhead were, therefore, tested under axial tension and the strains were measured using strain gauges as well as an image analysis technique, known as the Particle Image Velocimetry (PIV). The head hardened steel exhibit existence of three distinct zones of yield strength; the yield strength as the ratio of the average yield strength provided in the standard (σyr=780MPa) and
the corresponding depth as the ratio of the head hardened zone along
the axis of symmetry are as follows: (1.17 σyr, 20%), (1.06 σyr, 20%-80%) and (0.71 σyr, > 80%). The stress-strain curves exhibit limited plastic zone with fracture occurring at strain less than 0.1.
Abstract: Ultrafast doped zinc oxide crystal promised us a good
opportunity to build new instruments for ICF fusion neutron
measurement. Two pulsed neutron detectors based on ZnO crystal
wafer have been conceptually designed, the superfast ZnO timing
detector and the scintillation recoil proton neutron detection system.
The structure of these detectors was presented, and some characters
were studied as well. The new detectors could be much faster than
existing systems, and would be more competent for ICF neutron
diagnostics.
Abstract: The hard clam (meretrix lusoria) cultivated industry
has been developed vigorously for recent years in Taiwan, and
seawater quality determines the cultivated environment. The pH
concentration variation affects survival rate of meretrix lusoria
immediately. In order to monitor seawater quality, solid-state sensing
electrode of ruthenium-doped titanium dioxide (TiO2:Ru) is developed
to measure hydrogen ion concentration in different cultivated
solutions. Because the TiO2:Ru sensing electrode has high chemical
stability and superior sensing characteristics, thus it is applied as a pH
sensor. Response voltages of TiO2:Ru sensing electrode are readout by
instrument amplifier in different sample solutions. Mean sensitivity
and linearity of TiO2:Ru sensing electrode are 55.20 mV/pH and 0.999
from pH1 to pH13, respectively. We expect that the TiO2:Ru sensing
electrode can be applied to real environment measurement, therefore
we collect two sample solutions by different meretrix lusoria
cultivated ponds in the Yunlin, Taiwan. The two sample solutions are
both measured for 200 seconds after calibration of standard pH buffer
solutions (pH7, pH8 and pH 9). Mean response voltages of sample 1
and sample 2 are -178.758 mV (Standard deviation=0.427 mV) and
-180.206 mV (Standard deviation =0.399 mV), respectively. Response
voltages of the two sample solutions are between pH 8 and pH 9 which
conform to weak alkali range and suitable meretrix lusoria growth. For
long-term monitoring, drift of cultivated solutions (sample 1 and
sample 2) are 1.16 mV/hour and 1.03 mV/hour, respectively.
Abstract: Today-s children, who are born into a more colorful,
more creative, more abstract and more accessible communication
environment than their ancestors as a result of dizzying advances in
technology, have an interesting capacity to perceive and make sense
of the world. Millennium children, who live in an environment where
all kinds of efforts by marketing communication are more intensive
than ever are, from their early childhood on, subject to all kinds of
persuasive messages. As regards advertising communication, it
outperforms all the other marketing communication efforts in
creating little consumer individuals and, as a result of processing of
codes and signs, plays a significant part in building a world of seeing,
thinking and understanding for children. Children who are raised with
metaphorical expressions such as tales and riddles also meet that fast
and effective meaning communication in advertisements.
Children-s perception of metaphors, which help grasp the “product
and its promise" both verbally and visually and facilitate association
between them is the subject of this study. Stimulating and activating
imagination, metaphors have unique advantages in promoting the
product and its promise especially in regard to print advertisements,
which have certain limitations. This study deals comparatively with
both literal and metaphoric versions of print advertisements
belonging to various product groups and attempts to discover to what
extent advertisements are liked, recalled, perceived and are
persuasive. The sample group of the study, which was conducted in
two elementary schools situated in areas that had different socioeconomic
features, consisted of children aged 12.
Abstract: We have proposed an information filtering system
using index word selection from a document set based on the
topics included in a set of documents. This method narrows
down the particularly characteristic words in a document set
and the topics are obtained by Sparse Non-negative Matrix
Factorization. In information filtering, a document is often
represented with the vector in which the elements correspond
to the weight of the index words, and the dimension of the
vector becomes larger as the number of documents is
increased. Therefore, it is possible that useless words as index
words for the information filtering are included. In order to
address the problem, the dimension needs to be reduced. Our
proposal reduces the dimension by selecting index words
based on the topics included in a document set. We have
applied the Sparse Non-negative Matrix Factorization to the
document set to obtain these topics. The filtering is carried out
based on a centroid of the learning document set. The centroid
is regarded as the user-s interest. In addition, the centroid is
represented with a document vector whose elements consist of
the weight of the selected index words. Using the English test
collection MEDLINE, thus, we confirm the effectiveness of
our proposal. Hence, our proposed selection can confirm the
improvement of the recommendation accuracy from the other
previous methods when selecting the appropriate number of
index words. In addition, we discussed the selected index
words by our proposal and we found our proposal was able to
select the index words covered some minor topics included in
the document set.
Abstract: Text similarity measurement is a fundamental issue in
many textual applications such as document clustering, classification,
summarization and question answering. However, prevailing approaches
based on Vector Space Model (VSM) more or less suffer
from the limitation of Bag of Words (BOW), which ignores the semantic
relationship among words. Enriching document representation
with background knowledge from Wikipedia is proven to be an effective
way to solve this problem, but most existing methods still
cannot avoid similar flaws of BOW in a new vector space. In this
paper, we propose a novel text similarity measurement which goes
beyond VSM and can find semantic affinity between documents.
Specifically, it is a unified graph model that exploits Wikipedia as
background knowledge and synthesizes both document representation
and similarity computation. The experimental results on two different
datasets show that our approach significantly improves VSM-based
methods in both text clustering and classification.
Abstract: Nowadays, the importance of energy saving is clearance to everyone. By attention to increasing price of fuels and also the problems of environment pollutions, there are the most efforts for using fuels littler and more optimum in everywhere. This essay studies optimizing of gas consumption in gas-burner space heaters. In oven of each gas-burner space heaters there is two snags to prevent the hot air (the result of combustion of natural gas) to go out of oven of the gas-burner space heaters directly without delivering its heat to the space of favorite environment like a room. These snags cause a excess circulating that helps hot air deliver its heat to the space of favorite environment. It means the exhaust air temperature will be decreased then when there are no snags. This is the aim of this essay to use maximum potential energy of the natural gas to make heat. In this study, by the help of a finite volume software (FLUENT) consumption of the gas-burner space heaters is simulated and optimized. At the end of this writing, by comparing the results of software and experimental results, it will be proved the authenticity of this method.
Abstract: Service life of existing reinforced concrete (RC)
structures in coastal towns of Sabah has been affected very much.
Concrete crack, spalling of concrete cover and reinforcement rusting
of RC buildings are seen even within 5 years of construction in
Sabah. Hence, in this study a new mix design of concrete grout was
developed using locally available materials and investigated under
two curing conditions and workability, compressive strength,
Accelerated Mortar Bar Test (AMBT), water absorption, volume of
permeable voids (VPV), Sorptivity and 90-days salt ponding test
were conducted. The compressive strength of concrete grout at the
age 90 days was found to be 44.49 N/mm2 under water curing. It was
observed that the percentage of mortar bar length change was below
1% for developed concrete grout. The water absorption of the
concrete grout was in between the range of 0.88 % to 3.60 % under
two different curing up to the age 90 days. It was also observed that
the VPV of concrete was in the range of 0 % to 9.75 and 2.44% to
13.05% under water curing and site curing respectively. It was found
that the Sorptivity of the concrete grout under water curing at the age
of 28 days is 0.211mm/√min and at the age 90 day are 0.067
mm/√min. The chloride content decreased greatly, 90% after a depth
of 15 mm. It was noticed that the site cured samples showed higher
chloride contents near surface compared to water cured samples.
This investigation suggested that the developed mix design of
concrete grout using locally available construction materials can be
used for crack repairing of existing RC structures in Sabah.
Abstract: A variety of new technology-based services have
emerged with the development of Information and Communication
Technologies (ICTs). Since technology-based services have technology-driven characteristics, the identification of relationships
between technology-based services and ICTs would give meaningful implications. Thus, this paper proposes an approach for identifying the
relationships between technology-based services and ICTs by
analyzing patent documents. First, business model (BM) patents are
classified into relevant service categories. Second, patent citation
analysis is conducted to investigate the technological linkage and impacts between technology-based services and ICTs at macro level.
Third, as a micro level analysis, patent co-classification analysis is
employed to identify the technological linkage and coverage. The
proposed approach could guide and help managers and designers of
technology-based services to discover the opportunity of the development of new technology-based services in emerging service sectors.