Abstract: A capacity spectrum method (CSM), one of methodologies to evaluate seismic fragilities of building structures, has been long recognized as the most convenient method, even if it contains several limitations to predict the seismic response of structures of interest. This paper proposes the procedure to estimate seismic fragility curves using an incremental dynamic analysis (IDA) rather than the method adopting a CSM. To achieve the research purpose, this study compares the seismic fragility curves of a 5-story reinforced concrete (RC) moment frame obtained from both methods; an IDA method and aCSM. Both seismic fragility curves are similar in slight and moderate damage states whereas the fragility curve obtained from the IDA method presents less variation (or uncertainties) in extensive and complete damage states. This is due to the fact that the IDA method can properly capture the structural response beyond yielding rather than the CSM and can directly calculate higher mode effects. From these observations, the CSM could overestimate seismic vulnerabilities of the studied structure in extensive or complete damage states.
Abstract: A strain of Monascus purpureus CMU001 was used to
prepare red yeast rice from Thai glutinous rice Korkor 6 (RD 6).
Adding of different amounts of histidine (156, 312, 625 and 1250 mg
in 100 g of rice grains)) under aerobic and air limitation (air-lock)
condition were used in solid fermentation. Determination of the yield
as well as monacolin K content was done. Citrinin content was also
determined in order to confirm the safety use of prepared red yeast
rice. It was found that under air-lock condition with 1250 mg of
histidine addition gave the highest yield of 37.40 g of dried red yeast
rice prepared from 100 g of rice. Highest 5.72 mg content of
monacolin K was obtained under air-lock condition with 312 mg
histidine addition. In the other hand, citrinin content was found to be
less than 24462 ng/g of all dried red yeast rice samples under the
experimental methods used in this work.
Abstract: Examining existing experimental results for shallow
rigid foundations subjected to vertical centric load (N), accompanied
or not with a bending moment (M), two main non-linear mechanisms
governing the cyclic response of the soil-foundation system can be
distinguished: foundation uplift and soil yielding. A soil-foundation
failure limit, is defined as a domain of resistance in the two
dimensional (2D) load space (N, M) inside of which lie all the
admissible combinations of loads; these latter correspond to a pure
elastic, non-linear elastic or plastic behavior of the soil-foundation
system, while the points lying on the failure limit correspond to a
combination of loads leading to a failure of the soil-foundation
system. In this study, the proposed resistance domain is constructed
analytically based on mechanics. Original elastic limit, uplift
initiation limit and iso-uplift limits are constructed inside this
domain. These limits give a prediction of the mechanisms activated
for each combination of loads applied to the foundation. A
comparison of the proposed failure limit with experimental tests
existing in the literature shows interesting results. Also, the
developed uplift initiation limit and iso-uplift curves are confronted
with others already proposed in the literature and widely used due to
the absence of other alternatives, and remarkable differences are
noted, showing evident errors in the past proposals and relevant
accuracy for those given in the present work.
Abstract: In-memory database systems are becoming popular
due to the availability and affordability of sufficiently large RAM and
processors in modern high-end servers with the capacity to manage
large in-memory database transactions. While fast and reliable inmemory
systems are still being developed to overcome cache misses,
CPU/IO bottlenecks and distributed transaction costs, disk-based data
stores still serve as the primary persistence. In addition, with the
recent growth in multi-tenancy cloud applications and associated
security concerns, many organisations consider the trade-offs and
continue to require fast and reliable transaction processing of diskbased
database systems as an available choice. For these
organizations, the only way of increasing throughput is by improving
the performance of disk-based concurrency control. This warrants a
hybrid database system with the ability to selectively apply an
enhanced disk-based data management within the context of inmemory
systems that would help improve overall throughput.
The general view is that in-memory systems substantially
outperform disk-based systems. We question this assumption and
examine how a modified variation of access invariance that we call
enhanced memory access, (EMA) can be used to allow very high
levels of concurrency in the pre-fetching of data in disk-based
systems. We demonstrate how this prefetching in disk-based systems
can yield close to in-memory performance, which paves the way for
improved hybrid database systems. This paper proposes a novel EMA
technique and presents a comparative study between disk-based EMA
systems and in-memory systems running on hardware configurations
of equivalent power in terms of the number of processors and their
speeds. The results of the experiments conducted clearly substantiate
that when used in conjunction with all concurrency control
mechanisms, EMA can increase the throughput of disk-based systems
to levels quite close to those achieved by in-memory system. The
promising results of this work show that enhanced disk-based
systems facilitate in improving hybrid data management within the
broader context of in-memory systems.
Abstract: In this paper, effect of marginal quality groundwater
on yield of cotton crop and soil salinity was studied. In this
connection, three irrigation treatments each with four replications
were applied. These treatments were i) use of canal water (T1), ii) use
of marginal quality groundwater from tubewell (T2), and iii)
conjunctive use by mixing with the ratio of 1:1 of canal water and
marginal quality tubewell water (T3).
Water was applied to the crop cultivated in Kharif season 2011; its
quantity has been measured using cut-throat flume. Total 11 watering
each of 50 mm depth have been applied from 20th April to 20th July,
2011. Further, irrigations were stopped due to monsoon rainfall up to
crop harvesting.
Maximum crop yield (seed cotton) was observed under T1 which
was 1,517 kg/ha followed by T3 (mixed canal and tubewell water)
having 1009 kg/ha and T2 i.e. marginal quality groundwater having
709 kg/ha. This concludes that crop yield in T2 and T3 in comparison
to T1was reduced by about 53 and 30% respectively.
It has been observed that yield of cotton crop is below potential
limit for three treatments due to unexpected rainfall at the time of full
flowering season; thus the yield was adversely affected.
However, salt deposition in soil profiles was not observed that is
due to leaching effect of heavy rainfall occurred during monsoon
season.
Abstract: A field experiment was carried out at Arab El-
Awammer Research Station, Agric. Res. Center. Assiut Governorate
during summer seasons of 2013 and 2014. The present study assessed
the effect of cowpea with maize intercropping on yield and its
components. The experiment comprised of three treatments (sole
cowpea, sole maize and cowpea-maize intercrop). The experimental
design was a randomized complete block with four replications.
Results indicated that intercropped maize plants with cowpea,
exhibited greater potentiality and resulted in higher values of most of
the studied criteria viz., plant height, number of ears/plant, number of
rows/ear, number of grains/row, grains weight/ear, 100–grain weight
and straw and grain yields. Fresh and dry forage yields of cowpea
were lower in intercropping with maize than sole. Furthermore, the
combined of the two seasons revealed that the total Land Equivalent
Ratio (LER) between cowpea and maize was 1.65. The Aggressivity
(A) maize was 0.45 and cowpea was -0.45. This showed that maize
was the dominant crop, whereas cowpea was the dominated. The
Competitive Ratio (CR) indicated that maize more competitive than
cowpea, maize was 1.75 and cowpea was 0.57. The Actual Yield
Loss (AYL) maize was 0.05 and cowpea was -0.40. The Monetary
Advantage Index (MAI) was 2360.80.
Abstract: The tomato is a very important crop, whose
cultivation in the Mediterranean basin is severely affected by the
phytoparasitic weed Phelipanche ramosa. The semiarid regions of
the world are considered the main areas where this parasitic weed is
established causing heavy infestation as it is able to produce high
numbers of seeds (up to 500,000 per plant), which remain viable for
extended period (more than 20 years). In this paper the results
obtained from eleven treatments in order to control this parasitic
weed including chemical, agronomic, biological and biotechnological
methods compared with the untreated test under two plowing depths
(30 and 50 cm) are reported. The split-plot design with 3 replicates
was adopted. In 2014 a trial was performed in Foggia province
(southern Italy) on processing tomato (cv Docet) grown in the field
infested by Phelipanche ramosa. Tomato seedlings were transplant
on May 5, on a clay-loam soil. During the growing cycle of the
tomato crop, at 56-78 and 92 days after transplantation, the number
of parasitic shoots emerged in each plot was detected. At tomato
harvesting, on August 18, the major quantity-quality yield parameters
were determined (marketable yield, mean weight, dry matter, pH,
soluble solids and color of fruits). All data were subjected to analysis
of variance (ANOVA) and the means were compared by Tukey's test.
Each treatment studied did not provide complete control against
Phelipanche ramosa. However, among the different methods tested,
some of them which Fusarium, gliphosate, radicon biostimulant and
Red Setter tomato cv (improved genotypes obtained by Tilling
technology) under deeper plowing (50 cm depth) proved to mitigate
the virulence of the Phelipanche ramose attacks. It is assumed that
these effects can be improved combining some of these treatments
each other, especially for a gradual and continuing reduction of the
“seed bank” of the parasite in the soil.
Abstract: In this study, microcrystalline cellulose (MCC) was
extracted from oil palm empty fruit bunch (EFB) cellulose which was
earlier isolated from oil palm EFB fibre. In order to isolate the
cellulose, the chlorination method was carried out. Then, the MCC
was prepared by simultaneous ultrasonic and alkali treatment from
the isolated α-cellulose. Based on mass balance calculation, the yields
for MCC obtained from EFB was 44%. For fiber characterization, it
is observed that the chemical composition of the hemicellulose and
lignin for all samples decreased while composition for cellulose
increased. The structural property of the MCC was studied by X-ray
diffraction (XRD) method and the result shows that the MCC
produced is a cellulose-I polymorph, with 73% crystallinity.
Abstract: The financial crises caused a collapse in prices of
most asset classes, raising the attention on alternative investments
such as sukuk, a smaller, fast growing but often misunderstood
market. We study diversification benefits of sukuk, their correlation
with other asset classes and the effects of their inclusion in
investment portfolios of institutional and retail investors, through a
comprehensive comparison of their risk/return profiles during and
after the financial crisis.
We find a beneficial performance adjusted for the specific
volatility together with a lower correlation especially during the
financial crisis. The distribution of sukuk returns is positively skewed
and leptokurtic, with a risk/return profile similarly to high yield
bonds. Overall, our results suggest that sukuk present diversification
opportunities, a significant volatility-adjusted performance and lower
correlations especially during the financial crisis.
Our findings are relevant for a number of institutional investors.
Long term investors, such as life insurers would benefit from sukuk’s
protective features during financial crisis yet keeping return and
growth opportunities, whereas banks would gain due to their role of
placers, advisors, market makers or underwriters.
Abstract: The objective of this study was to determine effect of
dietary essential oil (EO) compounds, which contained
cinnamaldehyde, eugenol, peppermint, coriander, cumin, lemongrass,
and an organic carrier on feed intake, milk composition, and rumen
fermentation of dairy cows during heat exposure. Thirty-two Holstein
cows (days in milk= 60 ± 5) were assigned to one of two treatment
groups: a Control and EO fed. The experiment lasted 28 days. Dry
matter intake (DMI) was measured daily while and milk production
was measured weekly. Our result showed that DMI and milk yield
was decreased (P < 0.01) in control cows relative to EO cows.
Furthermore, supplementation with EO was associated with a
decrease in the molar proportion of propionate (P < 0.05) and
increase (P < 0.05) in acetate to propionate ratio. In conclusion, EO
supplementations in diets can be useful nutritional modification to
alleviate for the decrease DMI and milk production during heat
exposure in lactating dairy cows.
Abstract: Domestic goats (Capra hircus) are extremely diverse
species and principal animal genetic resource of the developing
world. These facilitate a persistent supply of meat, milk, fibre, and
skin and are considered as important revenue generators in small
pastoral environments. This study aimed to fingerprint β-LG gene at
PCR-RFLP level in native Saudi goat breeds (Ardi, Habsi and Harri)
in an attempt to have a preliminary image of β-LG genotypic patterns
in Saudi breeds as compared to other foreign breeds such as Indian
and Egyptian. Also, the Phylogenetic analysis was done to investigate
evolutionary trends and similarities among the caprine β-LG gene
with that of the other domestic specie, viz. cow, buffalo and sheep.
Blood samples were collected from 300 animals (100 for each breed)
and genomic DNA was extracted. A fragment of the β-LG gene
(427bp) was amplified using specific primers. Subsequent digestion
with Sac II restriction endonuclease revealed two alleles (A and B)
and three different banding patterns or genotypes i.e. AA, AB and
BB. The statistical analysis showed a general trend that β-LG AA
genotype had higher milk yield than β-LG AB and β-LG BB
genotypes. Nucleotide sequencing of the selected β-LG fragments
was done and submitted to GenBank NCBI (Accession No.
KJ544248, KJ588275, KJ588276, KJ783455, KJ783456 and
KJ874959). Phylogenetic analysis on the basis of nucleotide
sequences of native Saudi goats indicated evolutional similarity with
the GenBank reference sequences of goat, Bubalus bubalis and Bos
taurus. However, the origin of sheep which is the most closely
related from the evolutionary point of view, was located some
distance away.
Abstract: This review summarizes the potential of starch
agroindustrial residues as substrate for biohydrogen production.
Types of potential starch agroindustrial residues, recent developments
and bio-processing conditions for biohydrogen production will be
discussed. Biohydrogen is a clean energy source with great potential
to be an alternative fuel, because it releases energy explosively in
heat engines or generates electricity in fuel cells producing water as
only by-product. Anaerobic hydrogen fermentation or dark
fermentation seems to be more favorable, since hydrogen is yielded
at high rates and various organic waste enriched with carbohydrates
as substrate result in low cost for hydrogen production. Abundant
biomass from various industries could be source for biohydrogen
production where combination of waste treatment and energy
production would be an advantage. Carbohydrate-rich nitrogendeficient
solid wastes such as starch residues can be used for
hydrogen production by using suitable bioprocess technologies.
Alternatively, converting biomass into gaseous fuels, such as
biohydrogen is possibly the most efficient way to use these
agroindustrial residues.
Abstract: Nanostructured catalysts were successfully prepared
by acidification of diatomite and regeneration of FCC spent catalysts.
The obtained samples were characterized by IR, XRD, SEM, EDX,
MAS-NMR (27Al and 29Si), NH3-TPD and tested in catalytic
pyrolysis of biomass (rice straw). The results showed that the similar
bio-oil yield of 41.4% can be obtained by pyrolysis with catalysts at
450oC as compared to that of the pyrolysis without catalyst at 550oC.
The bio-oil yield reached a maximum of 42.55% at the pyrolysis
temperature of 500oC with catalytic content of 20%. Moreover, by
catalytic pyrolysis, bio-oil quality was better as reflected in higher
ratio of H/C, lower ratio of O/C. This clearly indicated high
application potential of these new nanostructured catalysts in the
production of bio-oil with low oxygenated compounds.
Abstract: The present study involved analysis of certain
characteristics of the perennial ryegrass (Lolium perenne L.)
genotypes collected from the natural flora of Ankara, and explores a
correlation among them. In order to evaluate the plants for breeding
purpose as per Turkey's environmental conditions, the perennial
ryegrass plants were collected from natural pasture of Ankara in 2004
and were utilized for the study. Seeds of the collected plants were
sown in pots and seedlings were prepared in a greenhouse. In 2005,
the seedlings were transplanted at 50 × 50 cm2 intervals in
Randomized Complete Blocks Design in an experimental field. In
2007 and 2008, data were recorded from the observations and
measurements of 568 perennial ryegrasses. The plant characteristics,
which were investigated, included re-growth time in spring, color,
density, growth habit, tendency to form inflorescence, time of
inflorescence, plant height, length of upper internode, spike length,
leaf length, leaf width, leaf area, leaf shape, number of spikelets per
spike, seed yield per spike and 1000 grain weight and the correlation
analyses were made using this data. Correlation coefficients were
estimated between all paired combinations of the studied traits. The
yield components exhibited varying trends of association among
themselves. Seed yield per spike showed significant and positive
association with the number of spikelets per spike, 1000 grain weight,
plant height, length of upper internode, spike length, leaf length, leaf
width, leaf area and color, but significant and negative association
with the growth habit and re-growth time in spring.
Abstract: This work presents the result of investigations aimed
at determining the hardness of the welded Chromoly (A 4130) steel
plate of 2” thickness. Multi pass welding for the thick sections was
carried out and analyzed for the Chromoly alloy steel plates. The
study of hardness at the weld metal reveals that there is the presence
of different micro structure products which yields diverse properties.
The welding carried out using GMAW with ER70s-2 electrode.
Single V groove design was selected for the butt joint configuration.
The presence of hydrogen has been suppressed by selecting low
hydrogen electrode. Preheating of the plate prior to welding reduces
the cooling rate which also affects the weld metal microstructure. The
shielding gas composition used in this analysis is 80% Ar-20% CO2.
The experimental analysis gives the detailed study of the hardness of
the material.
Abstract: The aim of the present work was to statistically design
an autotrophic medium for maximum biomass production by
Chlorella pyrenoidosa using response surface methodology. After
evaluating one factor at a time approach, K2HPO4, KNO3,
MgSO4.7H2O and NaHCO3 were preferred over the other
components of the fog’s medium as most critical autotrophic medium
components. The study showed that the maximum biomass yield was
achieved while the concentrations of MgSO4.7H2O, K2HPO4, KNO3
and NaHCO3 were 0.409 g/L, 0.24 g/L, 1.033 g/L, and 3.265 g/L,
respectively. The study reported that the biomass productivity of C.
pyrenoidosa improved from 0.14 g/L in defined fog’s medium to 1.40
g/L in modified fog’s medium resulting 10 fold increase. The
biochemical composition biosynthesis of C. pyrenoidosa was altered
using nitrogen limiting stress bringing about 5.23 fold increase in
lipid content than control (cell without stress), as analyzed by FTIR
integration method.
Abstract: In structures, stress concentration is a factor of fatigue
fracture. Basically, the stress concentration is a phenomenon that
should be avoided. However, it is difficult to avoid the stress
concentration. Therefore, relaxation of the stress concentration is
important. The stress concentration arises from notches and circular
holes. There is a relaxation method that a composite patch covers a
notch and a circular hole. This relaxation method is used to repair
aerial wings, but it is not systematized. Composites are more
expensive than single materials. Accordingly, we propose the
relaxation method that a single material patch covers a notch and a
circular hole, and aim to systematize this relaxation method.
We performed FEA (Finite Element Analysis) about an object by
using a three-dimensional FEA model. The object was that a patch
adheres to a plate with a circular hole. And, a uniaxial tensile load acts
on the patched plate with a circular hole. In the three-dimensional FEA
model, it is not easy to model the adhesion layer. Basically, the yield
stress of the adhesive is smaller than that of adherents. Accordingly,
the adhesion layer gets to plastic deformation earlier than the adherents
under the yield load of adherents. Therefore, we propose the
three-dimensional FEA model which is applied a nonlinear elastic
region to the adhesion layer. The nonlinear elastic region was
calculated by a bilinear approximation. We compared the analysis
results with the tensile test results to confirm whether the analysis
model has usefulness. As a result, the analysis results agreed with the
tensile test results. And, we confirmed that the analysis model has
usefulness.
As a result that the three-dimensional FEA model was used to the
analysis, it was confirmed that an out-of-plane deformation occurred
to the patched plate with a circular hole. The out-of-plane deformation
causes stress increase of the patched plate with a circular hole.
Therefore, we investigated that the out-of-plane deformation affects
relaxation of the stress concentration in the plate with a circular hole
on this relaxation method. As a result, it was confirmed that the
out-of-plane deformation inhibits relaxation of the stress concentration
on the plate with a circular hole.
Abstract: Esterification of p-bromo-m-cresol led to formation of
2-(4-bromo-3-methylphenoxy)acetate (1). 2-(4-Bromo-3-methyl
phenoxy)acetohydrazide (2) is derived from Compound (1) by
hydrazination. Compound (2) was reacted with different aromatic
aldehydes to yield N-(substituted benzylidiene)-2-(4-bromo-3-methyl
phenoxy)acetamide(3a-c). Cyclization of compound (3a-c) with
thioglycolic acid yielded 2-(4-bromo-3-methylphenoxy)-N-(4-oxo-2-
arylthiazolidin-3-yl) acetamide (4a-c). The newly synthesized
compounds were characterized on the basis of spectral studies and
evaluated for antibacterial and antifungal activities.
Abstract: Cement-based grouts has been used successfully to
repair cracks in many concrete structures such as bridges, tunnels,
buildings and to consolidate soils or rock foundations. In the present
study the rheological characterization of cement grout with
water/binder ratio (W/B) is fixed at 0.5. The effect of the replacement
of cement by bentonite (2 to 10% wt) in presence of superplasticizer
(0.5% wt) was investigated. Several rheological tests were carried out
by using controlled-stress rheometer equipped with vane geometry in
temperature of 20°C. To highlight the influence of bentonite and
superplasticizer on the rheological behavior of grout cement, various
flow tests in a range of shear rate from 0 to 200 s-1 were observed.
Cement grout showed a non-Newtonian viscosity behavior at all
concentrations of bentonite. Three parameter model Herschel-
Bulkley was chosen for fitting of experimental data. Based on the
values of correlation coefficients of the estimated parameters, The
Herschel-Bulkley law model well described the rheological behavior
of the grouts. Test results showed that the dosage of bentonite
increases the viscosity and yield stress of the system and introduces
more thixotropy. While the addition of both bentonite and
superplasticizer with cement grout improve significantly the fluidity
and reduced the yield stress due to the action of dispersion of SP.
Abstract: In order to study the effect of drought stress on grain
yield, yield components and associated traits of durum wheat
cultivars, an experiment was done as split plot arrangement using
randomized complete block design with three replications in Ilam
province, Iran in 2009-2010 cropping season. Different levels of
irrigation (Full irrigation, drought stress at stem elongation,
Flowering and grain formation stages) were considered as a main plot
and three durum wheat cultivars (Yavaros, Seimareh and Karkheh)
were assigned as a sub plot. The results showed that drought stress
was significant on grain yield, spike.m-2, grain. Spike-1, 1000-grain
weight, biological yield, harvest index and protein content. Drought
stress at all stages caused a loss in grain yield and its components.
Full irrigation had the highest grain yield and yield components.
Drought stress at stem elongation, flowering and grain formation
stages caused a reduction in spike.m-2, grain.spike-1 and 1000-grain
weight, respectively. Protein content was significantly affected by
drought stress. The highest protein content was obtained from
drought stress at grain formation stage. Cultivars had an influence on
grain yield and yield components. Yavaros and Seimareh cultivars
had the highest and lowest grain yield, respectively. Interaction effect
between drought stress and cultivar had a significant effect on grain
and yield components. Full irrigation and Yavaros cultivar had the
highest grain yield and drought stress at grain formation stage and
Seimareh cultivar had the lowest grain yield, respectively.