Abstract: The aim of this study was to extract sugar from
sugarcane using high electric field pulse (HELP) as a non-thermal cell permeabilization method. The result of this study showed that it
is possible to permeablize sugar cane cells using HELP at very short times (less than 10 sec.) and at room temperature. Increasing the field strength (from 0.5kV/cm to 2kV/cm) and pulse number (1 to 12) led to increasing the permeabilization of sugar cane cells. The energy
consumption during HELP treatment of sugar cane (2.4 kJ/kg) was about 100 times less compared to thermal cell disintegration at 85
Abstract: The electrokinetic flow resistance (electroviscous
effect) is predicted for steady state, pressure-driven liquid flow at
low Reynolds number in a microfluidic contraction of rectangular
cross-section. Calculations of the three dimensional flow are
performed in parallel using a finite volume numerical method. The
channel walls are assumed to carry a uniform charge density and the
liquid is taken to be a symmetric 1:1 electrolyte. Predictions are
presented for a single set of flow and electrokinetic parameters. It is
shown that the magnitude of the streaming potential gradient and the
charge density of counter-ions in the liquid is greater than that in
corresponding two-dimensional slit-like contraction geometry. The
apparent viscosity is found to be very close to the value for a
rectangular channel of uniform cross-section at the chosen Reynolds
number (Re = 0.1). It is speculated that the apparent viscosity for the
contraction geometry will increase as the Reynolds number is
reduced.
Abstract: Twenty four New Zealand white rabbits (12 does and
12 bucks) and twenty four Flanders (12 does and 12 bucks) rabbits,
allotted into two feeding regime (6 for each breed, 3 males and 3
females) first one fed commercial ration and second one fed
commercial diet plus sodium butyrate (300 g/ton). The obtained
results showed that at end of 8th week experimental period New
Zealand white rabbits were heavier body weight than Flanders rabbits
(1934.55+39.05 vs. 1802.5+30.99 g); significantly high body weight
gain during experimental period especially during 8th week
(136.1+3.5 vs. 126.8+1.8 g/week); better feed conversion ratio during
all weeks of experiment from first week (3.07+0.16 vs. 3.12+0.10)
till the 8th week of experiment (5.54+0.16 vs. 5.76+0.07) with
significantly high dressing percentages (0.54+0.01 vs. 0.52+0.01).
Also all carcass cuts were significantly high in New Zealand white
rabbits than Flanders. Females rabbits (at the same age) were lower
body weight than males from start of experiment (941.1+39.8
vs.972.1+33.5 g) till the end of experiment (1833.64+37.69 vs.
1903.41+36.93 g); gained less during all weeks of experiment except
during 8th week (132.1+2.3 vs. 130.9+3.4 g/week), with lower
dressing percentage (0.52+0.01 vs. 0.53+0.01) and lighter carcass
cuts than males, however, they had better feed conversion ratio
during 1st week, 7th week and 8th week of experiment. Addition of
300g sodium butyrate/ton of rabbit increased the body weight of
rabbits at the end of experimental period (1882.71+26.45 vs.
1851.5+49.82 g); improve body weight gain at 3rd, 4th, 5th, 6th and
7th week of experiment and significantly improve feed conversion
ratio during all weeks of the experiment from 1st week (2.85+0.07
vs. 3.30+0.15) till the 8th week of the experiment (5.51+0.12 vs.
5.77+0.12). Also the dressing percentage was higher in Sodium
butyrate fed groups than control one (0.53+0.01 vs. 0.52+0.01) and
the most important results of feeding sodium butyrate is the reducing
of the mortality percentage in rabbits during 8 week experiment to
zero percentage as compared with 16% in control group.
Abstract: In recent years Operational Transconductance Amplifier based high frequency integrated circuits, filters and systems have been widely investigated. The usefulness of OTAs over conventional OP-Amps in the design of both first order and second order active filters are well documented. This paper discusses some of the tunability issues using the Matlab/Simulink® software which are previously unreported for any commercial OTA. Using the simulation results two first order voltage controlled all pass filters with phase tuning capability are proposed.
Abstract: In this study, the density dependent nonlinear reactiondiffusion
equation, which arises in the insect dispersal models, is
solved using the combined application of differential quadrature
method(DQM) and implicit Euler method. The polynomial based
DQM is used to discretize the spatial derivatives of the problem. The
resulting time-dependent nonlinear system of ordinary differential
equations(ODE-s) is solved by using implicit Euler method. The
computations are carried out for a Cauchy problem defined by a onedimensional
density dependent nonlinear reaction-diffusion equation
which has an exact solution. The DQM solution is found to be in a
very good agreement with the exact solution in terms of maximum
absolute error. The DQM solution exhibits superior accuracy at large
time levels tending to steady-state. Furthermore, using an implicit
method in the solution procedure leads to stable solutions and larger
time steps could be used.
Abstract: Protein residue contact map is a compact
representation of secondary structure of protein. Due to the
information hold in the contact map, attentions from researchers in
related field were drawn and plenty of works have been done
throughout the past decade. Artificial intelligence approaches have
been widely adapted in related works such as neural networks,
genetic programming, and Hidden Markov model as well as support
vector machine. However, the performance of the prediction was not
generalized which probably depends on the data used to train and
generate the prediction model. This situation shown the importance
of the features or information used in affecting the prediction
performance. In this research, support vector machine was used to
predict protein residue contact map on different combination of
features in order to show and analyze the effectiveness of the
features.
Abstract: This paper analyzes different techniques of the fine grained security of relational databases for the two variables-data accessibility and inference. Data accessibility measures the amount of data available to the users after applying a security technique on a table. Inference is the proportion of information leakage after suppressing a cell containing secret data. A row containing a secret cell which is suppressed can become a security threat if an intruder generates useful information from the related visible information of the same row. This paper measures data accessibility and inference associated with row, cell, and column level security techniques. Cell level security offers greatest data accessibility as it suppresses secret data only. But on the other hand, there is a high probability of inference in cell level security. Row and column level security techniques have least data accessibility and inference. This paper introduces cell plus innocent security technique that utilizes the cell level security method but suppresses some innocent data to dodge an intruder that a suppressed cell may not necessarily contain secret data. Four variations of the technique namely cell plus innocent 1/4, cell plus innocent 2/4, cell plus innocent 3/4, and cell plus innocent 4/4 respectively have been introduced to suppress innocent data equal to 1/4, 2/4, 3/4, and 4/4 percent of the true secret data inside the database. Results show that the new technique offers better control over data accessibility and inference as compared to the state-of-theart security techniques. This paper further discusses the combination of techniques together to be used. The paper shows that cell plus innocent 1/4, 2/4, and 3/4 techniques can be used as a replacement for the cell level security.
Abstract: Many water supply systems in Australia are currently
undergoing significant reconfiguration due to reductions in long term
average rainfall and resulting low inflows to water supply reservoirs
since the second half of the 20th century. When water supply systems
undergo change, it is necessary to develop new operating rules,
which should consider climate, because the climate change is likely
to further reduce inflows. In addition, water resource systems are
increasingly intended to be operated to meet complex and multiple
objectives representing social, economic, environmental and
sustainability criteria. This is further complicated by conflicting
preferences on these objectives from diverse stakeholders. This paper
describes a methodology to develop optimum operating rules for
complex multi-reservoir systems undergoing significant change,
considering all of the above issues. The methodology is demonstrated
using the Grampians water supply system in northwest Victoria,
Australia. Initial work conducted on the project is also presented in
this paper.
Abstract: In this paper, we design an integration security system
that provides authentication service, authorization service, and
management service of security data and a unified interface for the
management service. The interface is originated from XKMS protocol
and is used to manage security data such as XACML policies, SAML
assertions and other authentication security data including public keys.
The system includes security services such as authentication,
authorization and delegation of authentication by employing SAML
and XACML based on security data such as authentication data,
attributes information, assertions and polices managed with the
interface in the system. It also has SAML producer that issues
assertions related on the result of the authentication and the
authorization services.
Abstract: Relational databases are often used as a basis for persistent storage of ontologies to facilitate rapid operations such as search and retrieval, and to utilize the benefits of relational databases management systems such as transaction management, security and integrity control. On the other hand, there appear more and more OWL files that contain ontologies. Therefore, this paper proposes to extract ontologies from OWL files and then store them in relational databases. A prerequisite for this storing is transformation of ontologies to relational databases, which is the purpose of this paper.
Abstract: At present time, competition, unpredictable fluctuations have made communication engineering education in the global sphere really difficult. Confront with new situation in the engineering education sector. Communication engineering education has to be reformed and ready to use more advanced technologies. We realized that one of the general problems of student`s education is that after graduating from their universities, they are not prepared to face the real life challenges and full skilled to work in industry. They are prepared only to think like engineers and professionals but they also need to possess some others non-technical skills. In today-s environment, technical competence alone is not sufficient for career success. Employers want employees (graduate engineers) who have good oral and written communication (soft) skills. It does require for team work, business awareness, organization, management skills, responsibility, initiative, problem solving and IT competency. This proposed curriculum brings interactive, creative, interesting, effective learning methods, which includes online education, virtual labs, practical work, problem-based learning (PBL), and lectures given by industry experts. Giving short assignments, presentations, reports, research papers and projects students can significantly improve their non-technical skills. Also, we noticed the importance of using ICT technologies in engineering education which used by students and teachers, and included that into proposed teaching and learning methods. We added collaborative learning between students through team work which builds theirs skills besides course materials. The prospective on this research that we intent to update communication engineering curriculum in order to get fully constructed engineer students to ready for real industry work.
Abstract: This paper was to study the clothes dryer using waste
heat from a split type air conditioner with a capacity of 12,648 btu/h.
The drying chamber had a minimum cross section area with the size
of 0.5 x 1.0 m2. The chamber was constructed by sailcloth and was
inside folded with aluminium foil. Then, it was connected to the
condensing unit of an air conditioner. The experiment was carried out
in two aspects which were the clothes drying with and without
auxiliary fan unit. The results showed that the drying rate of clothes
in the chamber installed with and without auxiliary fan unit were
2.26 and 1.1 kg/h, respectively. In case of the chamber installed with
a auxiliary fan unit, the additional power of 0.011 kWh was
consumed and the drying rate was higher than that of clothes drying
without auxiliary fan unit. Without auxiliary fan unit installation, no
energy was required but there was a portion of hot air leaks away
through the punctured holes at the wall of the drying chamber, hence
the drying rate was dropped below. The drying rate of clothes drying
using waste heat was higher than natural indoor drying and
commercial dryer which their drying rate were 0.17 and 1.9 kg/h,
respectively. It was noted that the COP of the air conditioner did not
change during the operating of clothes drying.
Abstract: Simultaneous Saccharification and Fermentation (SSF) of sugarcane bagasse by cellulase and Pachysolen tannophilus MTCC *1077 were investigated in the present study. Important process variables for ethanol production form pretreated bagasse were optimized using Response Surface Methodology (RSM) based on central composite design (CCD) experiments. A 23 five level CCD experiments with central and axial points was used to develop a statistical model for the optimization of process variables such as incubation temperature (25–45°) X1, pH (5.0–7.0) X2 and fermentation time (24–120 h) X3. Data obtained from RSM on ethanol production were subjected to the analysis of variance (ANOVA) and analyzed using a second order polynomial equation and contour plots were used to study the interactions among three relevant variables of the fermentation process. The fermentation experiments were carried out using an online monitored modular fermenter 2L capacity. The processing parameters setup for reaching a maximum response for ethanol production was obtained when applying the optimum values for temperature (32°C), pH (5.6) and fermentation time (110 h). Maximum ethanol concentration (3.36 g/l) was obtained from 50 g/l pretreated sugarcane bagasse at the optimized process conditions in aerobic batch fermentation. Kinetic models such as Monod, Modified Logistic model, Modified Logistic incorporated Leudeking – Piret model and Modified Logistic incorporated Modified Leudeking – Piret model have been evaluated and the constants were predicted.
Abstract: This paper presents a numerical approach for the static
and dynamic analysis of hydrodynamic radial journal bearings. In the
first part, the effect of shaft and housing deformability on pressure
distribution within oil film is investigated. An iterative algorithm that
couples Reynolds equation with a plane finite elements (FE)
structural model is solved. Viscosity-to-pressure dependency (Vogel-
Barus equation) is also included. The deformed lubrication gap and
the overall stress state are obtained. Numerical results are presented
with reference to a typical journal bearing configuration at two
different inlet oil temperatures. Obtained results show the great
influence of bearing components structural deformation on oil
pressure distribution, compared with results for ideally rigid
components. In the second part, a numerical approach based on
perturbation method is used to compute stiffness and damping
matrices, which characterize the journal bearing dynamic behavior.
Abstract: In this paper, a study on the applications of the
optimization and regression techniques for optimal calculation of
partial ratios of helical gearboxes with second-step double gear-sets
for minimal cross section dimension is introduced. From the condition
of the moment equilibrium of a mechanic system including three gear
units and their regular resistance condition, models for calculation of
the partial ratios of helical gearboxes with second-step double
gear-sets were given. Especially, by regression analysis, explicit
models for calculation of the partial ratios are introduced. These
models allow determining the partial ratios accurately and simply.
Abstract: Wireless Sensor Networks (WSNs) have attracted the attention of many researchers. This has resulted in their rapid integration in very different areas such as precision agriculture,environmental monitoring, object and event detection and military surveillance. Due to the current WSN characteristics this technology is specifically useful in industrial areas where security, reliability and autonomy are basic, such as nuclear power plants, chemical plants, and others. In this paper we present a system based on WSNs to monitor environmental conditions around and inside a nuclear power plant, specifically, radiation levels. Sensor nodes, equipped with radiation sensors, are deployed in fixed positions throughout the plant. In addition, plant staff are also equipped with mobile devices with higher capabilities than sensors such as for example PDAs able to monitor radiation levels and other conditions around them. The system enables communication between PDAs, which form a Mobile Ad-hoc Wireless Network (MANET), and allows workers to monitor remote conditions in the plant. It is particularly useful during stoppage periods for inspection or in the event of an accident to prevent risk situations.
Abstract: This paper proposes the novel model order
formulation scheme to design a discrete PID controller for higher
order linear time invariant discrete systems. Modified PSO (MPSO)
based model order formulation technique has used to obtain the
successful formulated second order system. PID controller is tuned to
meet the desired performance specification by using pole-zero
cancellation and proposed design procedures. Proposed PID
controller is attached with both higher order system and formulated
second order system. System specifications are tabulated and closed
loop response is observed for stabilization process. The proposed
method is illustrated through numerical examples from literature.
Abstract: The purpose of this study is to investigate the chemical
degradation of the organophosphorus pesticide of parathion and
carbamate insecticide of methomyl in the aqueous phase through
Fenton process. With the employment of batch Fenton process, the
degradation of the two selected pesticides at different pH, initial
concentration, humic acid concentration, and Fenton reagent dosages
was explored. The Fenton process was found effective to degrade
parathion and methomyl. The optimal dosage of Fenton reagents (i.e.,
molar concentration ratio of H2O2 to Fe2+) at pH 7 for parathion
degradation was equal to 3, which resulted in 50% removal of
parathion. Similarly, the optimal dosage for methomyl degradation
was 1, resulting in 80% removal of methomyl. This study also found
that the presence of humic substances has enhanced pesticide
degradation by Fenton process significantly. The mass spectroscopy
results showed that the hydroxyl free radical may attack the single
bonds with least energy of investigated pesticides to form smaller
molecules which is more easily to degrade either through
physio-chemical or bilolgical processes.
Abstract: This paper investigates the relationship between state and business in the context of structural and institutional transformations in Indonesia following the collapse of the New Order regime in 1998. Since 1998, Indonesia has embarked on a shift from an authoritarian to democratic polity and from a centralised to a decentralised system of governance, transforming the country into the third largest democracy and one of the most decentralised states in the world. This paper examines whether the transformation of the Indonesian state has altered the pattern of state and business relations with focus on clientism and corruption as the key dependent variable, and probes how/to what extent this has changed as a result of the transformation and the ensuring shifts in business and state relations. Based on interviews with key government and business actors as well as prominent scholars in Indonesia, it is found that since the demise of the New Order, business associations in Indonesia have become more independent of state control and more influential in public decision-making whereas the government has become more responsive of business concerns and more committed to combat corruption and clientism. However, these changes have not necessarily rendered business people completely leave individualclientelistic relationship with the government, and simply pursue wider sectoral and business-wide collectivism as an alternative way of channelling their aspirations, which is expected to help reduce corruption and clientism in Indonesia. This paper concludes that democratisation and a more open politics may have helped reduce corruption and clientism in Indonesia through changes in government. However, it is still difficult to imply that such political transformation has fostered business collective action and a broader, more encompassing pattern of business lobbying and activism, which is expected to help reduce corruption and clientism.
Abstract: Over the past decades, automatic face recognition has become a highly active research area, mainly due to the countless application possibilities in both the private as well as the public sector. Numerous algorithms have been proposed in the literature to cope with the problem of face recognition, nevertheless, a group of methods commonly referred to as appearance based have emerged as the dominant solution to the face recognition problem. Many comparative studies concerned with the performance of appearance based methods have already been presented in the literature, not rarely with inconclusive and often with contradictory results. No consent has been reached within the scientific community regarding the relative ranking of the efficiency of appearance based methods for the face recognition task, let alone regarding their susceptibility to appearance changes induced by various environmental factors. To tackle these open issues, this paper assess the performance of the three dominant appearance based methods: principal component analysis, linear discriminant analysis and independent component analysis, and compares them on equal footing (i.e., with the same preprocessing procedure, with optimized parameters for the best possible performance, etc.) in face verification experiments on the publicly available XM2VTS database. In addition to the comparative analysis on the XM2VTS database, ten degraded versions of the database are also employed in the experiments to evaluate the susceptibility of the appearance based methods on various image degradations which can occur in "real-life" operating conditions. Our experimental results suggest that linear discriminant analysis ensures the most consistent verification rates across the tested databases.