Abstract: Dill (Anethum graveolens L.) is a popular herb used in
many regions, including Baltic countries. Dill is widely used for
flavoring foods and beverages due to its pleasant spicy aroma. The
aim of this work was to determine the best blanching method for
processing of dill prior to microwave vacuum drying based on
sensory properties, color and volatile compounds in dried product.
Two blanching mediums were used – water and steam, and for part of
samples microwave pretreatment was additionally used. Evaluation of
dried dill volatile aroma compounds, color changes and sensory
attributes was performed. Results showed that blanching significantly
influences the quality of dried dill. After evaluation of volatile aroma
compounds, color and sensory properties of microwave vacuum dried
dill, as the best method for dill pretreatment was established
blanching at 90 °C for 30 s.
Abstract: This paper presents a new and efficient approach for
capacitor placement in radial distribution systems that determine
the optimal locations and size of capacitor with an objective of
improving the voltage profile and reduction of power loss. The
solution methodology has two parts: in part one the loss sensitivity
factors are used to select the candidate locations for the capacitor
placement and in part two a new algorithm that employs Plant growth
Simulation Algorithm (PGSA) is used to estimate the optimal size
of capacitors at the optimal buses determined in part one. The main
advantage of the proposed method is that it does not require any
external control parameters. The other advantage is that it handles the
objective function and the constraints separately, avoiding the trouble
to determine the barrier factors. The proposed method is applied to 9
and 34 bus radial distribution systems. The solutions obtained by the
proposed method are compared with other methods. The proposed
method has outperformed the other methods in terms of the quality
of solution.
Abstract: Diagnostic and detection of the arterial stiffness is
very important; which gives indication of the associated increased risk of cardiovascular diseases. To make a cheap and easy method for general screening technique to avoid the future cardiovascular
complexes , due to the rising of the arterial stiffness ; a proposed algorithm depending on photoplethysmogram to be used. The
photoplethysmograph signals would be processed in MATLAB. The
signal will be filtered, baseline wandering removed, peaks and
valleys detected and normalization of the signals should be achieved
.The area under the catacrotic phase of the photoplethysmogram
pulse curve is calculated using trapezoidal algorithm ; then will used
in cooperation with other parameters such as age, height, blood
pressure in neural network for arterial stiffness detection. The Neural
network were implemented with sensitivity of 80%, accuracy 85%
and specificity of 90% were got from the patients data. It is
concluded that neural network can detect the arterial STIFFNESS
depending on risk factor parameters.
Abstract: The determination of sugars in foods is very
significant. Their relation in fact, can affect the chemical and
sensorial quality of the matrix (e.g., sweetness, pH, total acidity,
microbial stability, global acceptability) and can provide information
on food to optimize several selected technological processes. Three
stages of ripeness (green, yellow and red) of tomatoes (Lycopersicon
Esculentum cv. Elegance) at different harvest dates were evaluated.
Fruit from all harvests were exposed to different of ozone doses
(0.25, 0.50 and 1 mg O3/g tomatoes) and clean air for 5 day at 15
°C±2 and 90-95 % relative humidity. Then, fruits were submitted for
extraction and analysis after a day from the finish of exposure of each
stage. The concentrations of the glucose and fructose increased in the
tomatoes which were subjected to ozone treatments.
Abstract: Order reduction of linear-time invariant systems employing two methods; one using the advantages of Routh approximation and other by an evolutionary technique is presented in this paper. In Routh approximation method the denominator of the reduced order model is obtained using Routh approximation while the numerator of the reduced order model is determined using the indirect approach of retaining the time moments and/or Markov parameters of original system. By this method the reduced order model guarantees stability if the original high order model is stable. In the second method Particle Swarm Optimization (PSO) is employed to reduce the higher order model. PSO method is based on the minimization of the Integral Squared Error (ISE) between the transient responses of original higher order model and the reduced order model pertaining to a unit step input. Both the methods are illustrated through numerical examples.
Abstract: In recent years, global warming has become a
worldwide problem. The reduction of carbon dioxide emissions is a
top priority for many companies in the manufacturing industry. In the
automobile industry as well, the reduction of carbon dioxide emissions
is one of the most important issues. Technology to reduce the weight
of automotive parts improves the fuel economy of automobiles, and is
an important technology for reducing carbon dioxide. Also, even if
this weight reduction technology is applied to electric automobiles
rather than gasoline automobiles, reducing energy consumption
remains an important issue. Plastic processing of hollow pipes is one
important technology for realizing the weight reduction of automotive
parts. Ohashi et al. [1],[2] present an example of research on pipe
formation in which a process was carried out to enlarge a pipe
diameter using a lost core, achieving the suppression of wall thickness
reduction and greater pipe expansion than hydroforming.
In this study, we investigated a method to increase the wall
thickness of a pipe through pipe compression using planetary rolls.
The establishment of a technology whereby the wall thickness of a
pipe can be controlled without buckling the pipe is an important
technology for the weight reduction of products. Using the finite
element analysis method, we predicted that it would be possible to
increase the compression of an aluminum pipe with a 3mm wall
thickness by approximately 20%, and wall thickness by approximately
20% by pressing the hollow pipe with planetary rolls.
Abstract: Education in the modern world provides the socioeconomic
progress of society. In today's society, where the presence
of large middle class ensures its stability and is a symbol of
resolution of hidden economic problems, education is an integral part
of formation and reproduction of the middle class. This article presents part of results of the sociological study conducted under the
project "Kazakhstan model of education: international experience and national traditions" supported by the Foundation of the First President
of Republic of Kazakhstan - Leader of the Nation to determine the
ratio of students to the transformations of the educational system. The
authors conclude that the Kazakhstani system of education, passing
through the transformation processes, improving the quality of
educational programs and trying to correspond to the international
standards, not yet in full range, but begins to perform important
functions in the formation of the middle class.
Abstract: Tea has several types of essential elements. Potassium,
magnesium and phosphorus are some examples of these elements.
Tea is widely used drink in Turkey, also some people puts a lemon
wedge to tea for different taste. In this study potassium, magnesium
and phosphorus contents after the hot water brewing of black and
green tea were determined by Optical Emission Spectroscopy (ICPOES).
Furthermore, how the lemon addition to teas affects the
concentrations of the potassium, magnesium and phosphorus
amount are investigated.
From the results, potassium, magnesium and phosphorus
concentrations are found as 3003.3, 597.1, 1167.2 ppm in black tea
and 3718.0, 3830.5, 376.4 ppm in green tea, respectively. After
lemon addition potassium, magnesium and phosphorus
concentrations are changed to 14930, 830.4, 1113.5 ppm in black tea
and 15460.0, 909.5, 1152.5 ppm in green tea, respectively.
It is seen that lemon addition affects some essential elements in
black and green Turkish teas.
Abstract: The authors of this work indicate by means of a concrete example that it is possible to apply efficaciously the method of multiple criteria programming in dealing with the problem of determining the optimal production plan for a certain period of time. The work presents: (1) the selection of optimization criteria, (2) the setting of the problem of determining an optimal production plan, (3) the setting of the model of multiple criteria programming in finding a solution to a given problem, (4) the revised surrogate trade-off method, (5) generalized multicriteria model for solving production planning problem and problem of choosing technological variants in the metal manufacturing industry. In the final part of this work the authors reflect on the application of the method of multiple criteria programming while determining the optimal production plan in manufacturing enterprises.
Abstract: Ammonia nitrogen is one of the most hazardous
water pollutants, discharging into water receptors through industrial
effluents. Negative environmental impacts of such chemical species
in hydrosphere include accelerated eutrophication, water toxicity and
harming the aquatics. Natural zeolite clinoptilolite has very high
selectivity & capacity for ammonium cation sorption. It occurs in
high abundances and rich mines of this zeolite exist in different parts
of Iran and thus are available more cheaply and with different sizing.
The aim of this study is to investigate ammonia nitrogen removal
over this natural sorbent from real samples of high polluted
wastewater discharging from a fertilizer producing plant. The
experimental results showed that this natural sorbent without even
any pre treatment system & with the same particle size available in
Iranian markets has still high capability & selectivity in ammonia
nitrogen removal both in batch and continuous tests.
Abstract: This paper proposes a new optimal feedback controller
for voltage source converters VSC's, for current regulated voltage
source converters, which allows compensate the harmonics of current
produced by nonlinear loads and load reactive power. The aim of the
present paper is to describe a novel switching signal generation
technique called optimal controller which guarantees that the injected
currents follow the reference currents determined by the
compensation strategy, with the smallest possible tracking error and
fixed switching frequency. It is compared with well-known
hysteresis current controller HCC. The validity of presented method
and its comparison with HCC is studied through simulation results.
Abstract: A cross-sectional study was carried out to determine the prevalence, species characterization and associated risk factors with Eimeria (E.) in sheep of district Toba Tek Singh from April, 2009 to March, 2010. Of the total 486 faecal samples examined for Eimeria, 209 (43%) were found infected with five species of Eimeria. Amongst the identified species of Eimeria, E. ovinoidalis was the commonest one (48.32%), followed in order by E. ahsata, E. intricata, E. parva and E. faurei with prevalence of 45.45, 28.71, 24.40 and 19.14 percent respectively. Peak prevalence was observed in August. Wet season (rainy and post-rainy) was found to be favourable for Eimeria infection. Lambs had significantly higher prevalence (P < 0.05) of Eimeria than adults. Similarly higher prevalence of Eimeria was observed in female as compared to male. Among management and husbandry practices; watering system, housing system, floor type and herd size strongly influenced the prevalence of Eimeria. Coccidiosis was more prevalent in closed housing system, non-cemented floor type, pond watered animals and larger herds (P < 0.05) as compared to open housing system, partially cemented floor type, tap watered animals and smaller herds respectively. Feeding system, breed and body condition of animals were not found as risk factors (P>0.05) influencing prevalence of Eimeria.
Abstract: Extreme temperature of several stations in Malaysia is
modelled by fitting the monthly maximum to the Generalized
Extreme Value (GEV) distribution. The Mann-Kendall (MK) test
suggests a non-stationary model. Two models are considered for
stations with trend and the Likelihood Ratio test is used to determine
the best-fitting model. Results show that half of the stations favour a
model which is linear for the location parameters. The return level is
the level of events (maximum temperature) which is expected to be
exceeded once, on average, in a given number of years, is obtained.
Abstract: In this paper, a data mining model to SMEs for detecting financial and operational risk indicators by data mining is presenting. The identification of the risk factors by clarifying the relationship between the variables defines the discovery of knowledge from the financial and operational variables. Automatic and estimation oriented information discovery process coincides the definition of data mining. During the formation of model; an easy to understand, easy to interpret and easy to apply utilitarian model that is far from the requirement of theoretical background is targeted by the discovery of the implicit relationships between the data and the identification of effect level of every factor. In addition, this paper is based on a project which was funded by The Scientific and Technological Research Council of Turkey (TUBITAK).
Abstract: In order to avoid the potentially devastating
consequences of global warming and climate change, the carbon
dioxide “CO2" emissions caused due to anthropogenic activities must
be reduced considerably. This paper presents the first study
examining the feasibility of carbon sequestration in construction and
demolition “C&D" waste. Experiments were carried out in a self
fabricated Batch Reactor at 40ºC, relative humidity of 50-70%, and
flow rate of CO2 at 10L/min for 1 hour for water-to-solids ratio of 0.2
to 1.2. The effect of surface area was found by comparing the
theoretical extent of carbonation of two different sieve sizes (0.3mm
and 2.36mm) of C&D waste. A 38.44% of the theoretical extent of
carbonation equating to 4% CO2 sequestration extent was obtained
for C&D waste sample for 0.3mm sieve size. Qualitative,
quantitative and morphological analyses were done to validate
carbonate formation using X-ray diffraction “X.R.D.," thermal
gravimetric analysis “T.G.A., “X-Ray Fluorescence Spectroscopy
“X.R.F.," and scanning electron microscopy “S.E.M".
Abstract: The treatment of the industrial wastewater can be
particularly difficult in the presence of toxic compounds. Excessive
concentration of Chromium in soluble form is toxic to a wide variety
of living organisms. Biological removal of heavy metals using natural
and genetically engineered microorganisms has aroused great interest
because of its lower impact on the environment. Ralston
metallidurans, formerly known as Alcaligenes eutrophus is a LProteobacterium
colonizing industrial wastewater with a high content
of heavy metals. Tris-buffered mineral salt medium was used for
growing Alcaligenes eutrophus AE104 (pEBZ141). The cells were
cultivated for 18 h at 30 oC in Tris-buffered mineral salt medium
containing 3 mM disodium sulphate and 46 mM sodium gluconate as
the carbon source. The cells were harvested by centrifugation,
washed, and suspended in 10 mM Tris HCl, pH 7.0, containing 46
mM sodium gluconate, and 5 mM Chromium. Interaction among
induction of chr resistance determinant, and chromate reduction have
been demonstrated. Results of this study show that the above bacteria
can be very useful for bioremediation of chromium from industrial
wastewater.
Abstract: Signal processing applications which are iterative in
nature are best represented by data flow graphs (DFG). In these
applications, the maximum sampling frequency is dependent on the
topology of the DFG, the cyclic dependencies in particular. The
determination of the iteration bound, which is the reciprocal of the
maximum sampling frequency, is critical in the process of hardware
implementation of signal processing applications. In this paper, a
novel technique to compute the iteration bound is proposed. This
technique is different from all previously proposed techniques, in the
sense that it is based on the natural flow of tokens into the DFG
rather than the topology of the graph. The proposed algorithm has
lower run-time complexity than all known algorithms. The
performance of the proposed algorithm is illustrated through
analytical analysis of the time complexity, as well as through
simulation of some benchmark problems.
Abstract: Thai and Vietnamese music had been influenced and inspired by the traditional Chinese music. Whereby the differences of the tuning systems as well as the music modes are obviously known . The research examined the character of musical instruments, songs and culture between Thai and Vietnamese. An analyzing of songs and modes and the study of tone vibration as well as timbre had been done accurately. This qualitative research is based on documentary and songs analysis, field study, interviews and focus group discussion of Thai and Vietnamese masters. The research aims are to examine the musical instruments and songs of both Thai and Vietnamese as well as the comparison of the sounding system between Thailand and Vietnam. The finding of the research has revealed that there are similarities in certain kinds of instruments but differences in the sound systems regarding songs and scale of Thailand and Vietnam. Both cultural musical instruments are diverse and synthetic combining native and foreign inspiring. An integral part of Vietnam has been highly impacted by Chinese musical convention. Korea, Mongolia and Japan music have also play an active and effectively influenced as their geographical related. Whereas Thailand has been influenced by Chinese and Indian traditional music. Both Thai and Vietnamese musical instruments can be divided into four groups: plucked strings, bowed strings, winds and percussion. Songs from both countries have their own characteristics. They are playing a role in touching people heart in ceremonies, social functions and an essential element of the native performing arts. The Vietnamese music melodies have been influenced by Chinese music and taken the same character as Chinese songs. Thai song has specific identity and variety showed in its unique melody. Pentatonic scales have effectively been used in composing Thai and Vietnamese songs, but in different implementing concept.
Abstract: To calculate the temperature distribution of the slab in
a hot rolled reheating furnace a mathematical model has been
developed by considering the thermal radiation in the furnace and
transient conduction in the slab. The furnace is modeled as radiating
medium with spatially varying temperature. Radiative heat flux within
the furnace including the effect of furnace walls, combustion gases,
skid beams and buttons is calculated using the FVM and is applied as
the boundary condition of the transient conduction equation of the
slab. After determining the slab emissivity by comparison between
simulation and experimental work, variation of heating characteristics
in the slab is investigated in the case of changing furnace temperature
with various time and the slab residence time is optimized with this
evaluation.
Abstract: Service trade is an important force of influencing economic development. A review on the related literatures is done firstly. Then through the construction of a Diamond Model, the main factors which influence the competitiveness of Chinese service trade are determined. With three competitiveness indexes served as the reference series respectively, the influencing factors served as the comparable series, three grey incidence models are then built up to conduct an empirical analysis on the main factors influencing the competitiveness of service trade after China entering WTO. The result indicates that urbanization level, open degree of service industry and foreign direct investment have larger impacts on Chinese service trade competitiveness, followed in turn by GDP in service industry and human capital, while commodity trade has the minimum impact. Further discussion provides train of thought for the upgrade of Chinese service trade competitiveness.