Abstract: While choosing insulating oil, characteristic features
such as thermal cooling, endurance, efficiency and being
environment-friendly should be considered. Mineral oils are referred
as petroleum-based oil. In this study, vegetable oils investigated as an
alternative insulating liquid to mineral oil. Dissipation factor,
breakdown voltage, relative dielectric constant and resistivity
changes with the frequency and voltage of mineral, rapeseed and nut
oils were measured. Experimental studies were performed according
to ASTM D924 and IEC 60156 standards.
Abstract: Residential buildings consume significant amounts of
energy and produce large amount of emissions and waste. However,
there is a substantial potential for energy savings in this sector which
needs to be evaluated over the life cycle of residential buildings. Life
Cycle Assessment (LCA) methodology has been employed to study
the primary energy uses and associated environmental impacts of
different phases (i.e., product, construction, use, end of life, and
beyond building life) for residential buildings. Four different
alternatives of residential buildings in Vancouver (BC, Canada) with
a 50-year lifespan have been evaluated, including High Rise
Apartment (HRA), Low Rise Apartment (LRA), Single family
Attached House (SAH), and Single family Detached House (SDH).
Life cycle performance of the buildings is evaluated for embodied
energy, embodied environmental impacts, operational energy,
operational environmental impacts, total life-cycle energy, and total
life cycle environmental impacts. Estimation of operational energy
and LCA are performed using DesignBuilder software and Athena
Impact estimator software respectively.
The study results revealed that over the life span of the buildings,
the relationship between the energy use and the environmental
impacts are identical. LRA is found to be the best alternative in terms
of embodied energy use and embodied environmental impacts; while,
HRA showed the best life-cycle performance in terms of minimum
energy use and environmental impacts. Sensitivity analysis has also
been carried out to study the influence of building service lifespan
over 50, 75, and 100 years on the relative significance of embodied
energy and total life cycle energy. The life-cycle energy requirements
for SDH are found to be a significant component among the four
types of residential buildings. The overall disclose that the primary
operations of these buildings accounts for 90% of the total life cycle
energy which far outweighs minor differences in embodied effects
between the buildings.
Abstract: This paper proposes a linear model for optimizing
domestic energy consumption in Romania. The particularity of the
model is that it is putting in competition both tangible technologies
and thermal insulation projects with different financing modes.
The model is optimizing the energy system by minimizing the
global discounted cost in household sector, by integrating residential
lighting, space heating, hot water, combined space heating – hot
water, as well as space cooling, in a monolithic model. Another
demand sector included is the passenger transport.
This paper focuses on space heating part, analyzing technical and
economic issues related to investment decisions to envelope and
insulate buildings, in order to minimize energy consumption.
Abstract: Brownfields are one of the most important problems
that must be solved by today's cities. The topic of this article is
description of developing a comprehensive transformation of postindustrial
area of the former iron factory national cultural heritage
lower Vítkovice. City of Ostrava used to be industrial superpower of
the Czechoslovak Republic, especially in the area of coal mining and
iron production, after declining industrial production and mining in
the 80s left many unused areas of former factories generally
brownfields and backfields. Since the late 90s we are observing how
the city officials or private entities seeking to remedy this situation.
Regeneration of brownfields is a very expensive and long-term
process. The area is now rebuilt for tourists and residents of the city
in the entertainment, cultural, and social center. It was necessary do
the reconstruction of the industrial monuments. Equally important
was the construction of new buildings, which helped reusing of the
entire complex. This is a unique example of transformation of
technical monuments and completion of necessary new objects, so
that the area could start working again and reintegrate back into the
urban system.
Abstract: A new fast growing trend in tourism is ecotourism, in
which tourists visit natural ecosystems under low impact, nonconsumptive
and locally oriented activities. Through these activities
species and habitats are maintained and typically, underdeveloped
regions are emphasized. Ecotourism provides a great alternative,
especially for rural and undeveloped area. At the same time, despite
its many benefits, it also poses many risks for the naturally protected
areas. If ecotourism is practiced improperly degradation and
irreversible damages could be the unwanted result. In addition, the
lack of MSc programs in the field of Ecotourism in Europe makes it a
necessity to be developed. Such an MSc program is being
implemented with the lead partner the Technical University of
Madrid. The entire partnership has six Universities, seven SMEs and
one National Park from seven different countries all over Europe.
The MSc will have 10 educational modules that will be available
online and will prepare professionals that will be able to implement
ecotourism in a sustainable way. Only through awareness and
education a sustainable ecotourism will be achieved in the protected
areas of Europe.
Abstract: It is a major challenge to build a bridge superstructure
that has long-term durability and low maintenance requirements. A
solution to this challenge may be to use new materials or to
implement new structural systems. Fiber Reinforced Polymer (FRP)
composites have continued to play an important role in solving some
of persistent problems in infrastructure applications because of its
high specific strength, light weight, and durability. In this study, the
concept of the hybrid FRP-concrete structural systems is applied to a
bridge superstructure. The hybrid FRP-concrete bridge superstructure
is intended to have durable, structurally sound, and cost effective
hybrid system that will take full advantage of the inherent properties
of both FRP materials and concrete. In this study, two hybrid FRP-concrete
bridge systems were investigated. The first system consists
of trapezoidal cell units forming a bridge superstructure. The second
one is formed by arch cells. The two systems rely on using cellular
components to form the core of the bridge superstructure, and an
outer shell to warp around those cells to form the integral unit of the
bridge. Both systems were investigated analytically by using finite
element (FE) analysis. From the rigorous FE studies, it was
concluded that first system is more efficient than the second.
Abstract: The main objective of this study was to determine the
effects of Nitrogen fixing bacteria and manure application on the seed
yield and yield components in black cumin (Nigella sativa L.). The
experiment was carried out at the RAN Research Station in
Firouzkouh in 2012. A 4×4 factorial experiment, arranged in a
randomized complete blocks designed with three replications.
Nitrogen fixing bacteria at 4 levels (control, Azotobacter,
Azospirillum and Azotobacter + Azospirillum) and manure
application at 4 levels (0, 2.5, 5 and 7.5 ton ha-1) were used at this
investigation. The present results have shown that the highest height,
1000 seeds weight, seed number per follicle, follicle yield, seed yield
and harvest index were obtained after using Azotobacter and
Azospirillum, simultaneously. Manure application only effects on
follicle yield and by 5ton manure ha-1 the highest follicle yield
obtained. Results of this investigation showed that the maximum seed
yield obtained when Aotobacter+Azospirillum inoculated with black
cumin seeds and 5 ton manure ha-1 applied. According to the results
of this investigation the integrated management of Azotobacter and
Azospirillum with manure application is the best treatment for
achieving the maximum quantitative charactersitics of Black cumin.
Abstract: Si ion implantation was widely used to synthesize
specimens of SiO2 containing supersaturated Si and subsequent high
temperature annealing induces the formation of embedded
luminescent Si nanocrystals. In this work, the potentialities of excimer
UV-light (172 nm, 7.2 eV) irradiation and rapid thermal annealing
(RTA) to enhance the photoluminescence and to achieve low
temperature formation of Si nanocrystals have been investigated. The
Si ions were introduced at acceleration energy of 180 keV to fluence of
7.5 x 1016 ions/cm2. The implanted samples were subsequently
irradiated with an excimer-UV lamp. After the process, the samples
were rapidly thermal annealed before furnace annealing (FA).
Photoluminescence spectra were measured at various stages at the
process. We found that the luminescence intensity is strongly
enhanced with excimer-UV irradiation and RTA. Moreover, effective
visible photoluminescence is found to be observed even after FA at
900 oC, only for specimens treated with excimer-UV lamp and RTA.
We also prepared specimens of Si nanocrystals embedded in a SiO2 by
reactive pulsed laser deposition (PLD) in an oxygen atmosphere. We
will make clear the similarities and differences with the way of
preparation.
Abstract: An Acoustic Micro-Energy Harvester (AMEH) is
developed to convert wasted acoustical energy into useful electrical
energy. AMEH is mathematically modeled using Lumped Element
Modelling (LEM) and Euler-Bernoulli beam (EBB) modelling. An
experiment is designed to validate the mathematical model and assess
the feasibility of AMEH. Comparison of theoretical and experimental
data on critical parameter value such as Mm, Cms, dm and Ceb showed
the variances are within 1% to 6%, which is reasonably acceptable.
Then, AMEH undergoes bandwidth tuning for performance
optimization. The AMEH successfully produces 0.9V/(m/s^2) and
1.79μW/(m^2/s^4) at 60Hz and 400kΩ resistive load which only
show variances about 7% compared to theoretical data. At 1g and
60Hz resonance frequency, the averaged power output is about
2.2mW which fulfilled a range of wireless sensors and
communication peripherals power requirements. Finally, the design
for AMEH is assessed, validated and deemed as a feasible design.
Abstract: This study investigates the effects of the lead angle
and chip thickness variation on surface roughness during the
machining of compacted graphite iron using ceramic cutting tools
under dry cutting conditions. Analytical models were developed for
predicting the surface roughness values of the specimens after the
face milling process. Experimental data was collected and imported
to the artificial neural network model. A multilayer perceptron model
was used with the back propagation algorithm employing the input
parameters of lead angle, cutting speed and feed rate in connection
with chip thickness. Furthermore, analysis of variance was employed
to determine the effects of the cutting parameters on surface
roughness. Artificial neural network and regression analysis were
used to predict surface roughness. The values thus predicted were
compared with the collected experimental data, and the
corresponding percentage error was computed. Analysis results
revealed that the lead angle is the dominant factor affecting surface
roughness. Experimental results indicated an improvement in the
surface roughness value with decreasing lead angle value from 88° to
45°.
Abstract: Food poisoning and infection by bacteria are of public
health significance to both developing and developed countries.
Samples of ogi (akamu) prepared from white and yellow variety of
maize sold in Uturu and Okigwe were analyzed together with the
laboratory prepared ogi for bacterial quality using the standard
microbiological methods. The analyses showed that both white and
yellow variety had total bacterial counts (cfu/g) of 4.0 ×107 and 3.9 x
107 for the laboratory prepared ogi while the commercial ogi had 5.2
x 107 and 4.9 x107, 4.9 x107 and 4.5 x107, 5.4 x107 and 5.0 x107 for
Eke-Okigwe, Up-gate and Nkwo-Achara market respectively. The
Staphylococcal counts ranged from 2.0 x 102 to 5.0 x102 and 1.0 x
102 to 4.0 x102 for the white and yellow variety from the different
markets while Staphylococcal growth was not recorded on the
laboratory prepared ogi. The laboratory prepared ogi had no Coliform
growth while the commercially prepared ogi had counts of 0.5 x103
to 1.6 x 103 for white variety and 0.3 x 103 to 1.1 x103 for yellow
variety respectively. The Lactic acid bacterial count of 3.5x106 and
3.0x106 was recorded for the laboratory ogi while the commercially
prepared ogi ranged from 3.2x106 to 4.2x106 (white variety) and 3.0
x106 to 3.9 x106 (yellow). The presence of bacteria isolates from the
commercial and laboratory fermented ogi showed that Lactobacillus
sp, Leuconostoc sp and Citrobacter sp were present in all the
samples, Micrococcus sp and Klebsiella sp were isolated from Eke-
Okigwe and ABSU-up-gate markets varieties respectively, E. coli
and Staphylococcus sp were present in Eke-Okigwe and Nkwo-
Achara markets while Salmonella sp were isolated from the three
markets. Hence, there are chances of contracting food borne diseases
from commercially prepared ogi. Therefore, there is the need for
sanitary measures in the production of fermented cereals so as to
minimize the rate of food borne pathogens during processing and
storage.
Abstract: Waste Load Allocation (WLA) strategies usually
intend to find economic policies for water resource management.
Water quality trading (WQT) is an approach that uses discharge
permit market to reduce total environmental protection costs. This
primarily requires assigning discharge limits known as total
maximum daily loads (TMDLs). These are determined by monitoring
organizations with respect to the receiving water quality and
remediation capabilities. The purpose of this study is to compare two
approaches of TMDL assignment for WQT policy in small catchment
area of Haraz River, in north of Iran. At first, TMDLs are assigned
uniformly for the whole point sources to keep the concentrations of
BOD and dissolved oxygen (DO) at the standard level at checkpoint
(terminus point). This was simply simulated and controlled by
Qual2kw software. In the second scenario, TMDLs are assigned
using multi objective particle swarm optimization (MOPSO) method
in which the environmental violation at river basin and total treatment
costs are minimized simultaneously. In both scenarios, the equity
index and the WLA based on trading discharge permits (TDP) are
calculated. The comparative results showed that using economically
optimized TMDLs (2nd scenario) has slightly more cost savings rather
than uniform TMDL approach (1st scenario). The former annually
costs about 1 M$ while the latter is 1.15 M$. WQT can decrease
these annual costs to 0.9 and 1.1 M$, respectively. In other word,
these approaches may save 35 and 45% economically in comparison
with command and control policy. It means that using multi objective
decision support systems (DSS) may find more economical WLA,
however its outcome is not necessarily significant in comparison with
uniform TMDLs. This may be due to the similar impact factors of
dischargers in small catchments. Conversely, using uniform TMDLs
for WQT brings more equity that makes stakeholders not feel that
much envious of difference between TMDL and WQT allocation. In
addition, for this case, determination of TMDLs uniformly would be
much easier for monitoring. Consequently, uniform TMDL for TDP
market is recommended as a sustainable approach. However,
economical TMDLs can be used for larger watersheds.
Abstract: This work consists of a numerical simulation of
convective heat transfer in a vertical plane channel filled with a heat
generating porous medium, in the absence of local thermal
equilibrium. The walls are maintained to a constant temperature and
the inlet velocity is uniform. The dynamic range is described by the
Darcy-Brinkman model and the thermal field by two energy
equations model. A dimensionless formulation is developed for
performing a parametric study based on certain dimensionless groups
such as, the Biot interstitial number, the thermal conductivity ratio
and the volumetric heat generation, q '''. The governing equations are
solved using the finite volume method, gave rise to a multitude of
results concerning in particular the thermal field in the porous
channel and the existence or not of the local thermal equilibrium.
Abstract: Psyllium gum alone and in combination with
sunflower oil was investigated as a possible alternative edible coating
for improvement of quality and shelf life of fresh-cut papaya.
Different concentrations including 0.5, 1 and 1.5 percent of psyllium
gum were used for coating of fresh-cut papaya. In some samples,
refined sunflower oil was used as a lipid component to increase the
effectiveness of coating in terms of water barrier properties. Soya
lecithin was used as an emulsifier in coatings containing oil.
Pretreatment with 1% calcium chloride was given to maintain the
firmness of fresh-cut papaya cubes. 1% psyllium gum coating was
found to yield better results. Further, addition of oil helped to
maintain the quality and acted as a barrier to water vapour, therefore,
minimizing the weight loss.
Abstract: In this study, the feasibility of incorporating ceramic
waste from bricks (perforated brick and double hollow brick) and
extruded polystyrene (XPS) waste, is analysed.
Results show that it is possible to incorporate up to 25% of
ceramic waste and 4% of XPS waste over the weight of gypsum in a
gypsum matrix. Furthermore, with the addition of ceramic waste an
8% of surface hardness increase and a 25% of capillary water
absorption reduction can be obtained. On the other hand, with the
addition of XPS, a 26% reduction of density and a 37% improvement
of thermal conductivity can be obtained.
The obtained results are favorable to use these materials in order to
produce prefabricated gypsum and also as material for interior
cladding walls.
Abstract: Several parameters are established in order to measure
biodiesel quality. One of them is the iodine value, which is an
important parameter that measures the total unsaturation within a
mixture of fatty acids. Limitation of unsaturated fatty acids is
necessary since warming of higher quantity of these ones ends in
either formation of deposits inside the motor or damage of lubricant.
Determination of iodine value by official procedure tends to be very
laborious, with high costs and toxicity of the reagents, this study uses
artificial neural network (ANN) in order to predict the iodine value
property as an alternative to these problems. The methodology of
development of networks used 13 esters of fatty acids in the input
with convergence algorithms of back propagation of back
propagation type were optimized in order to get an architecture of
prediction of iodine value. This study allowed us to demonstrate the
neural networks’ ability to learn the correlation between biodiesel
quality properties, in this caseiodine value, and the molecular
structures that make it up. The model developed in the study reached
a correlation coefficient (R) of 0.99 for both network validation and
network simulation, with Levenberg-Maquardt algorithm.
Abstract: A comparison of activity and stability of the as-formed
Pt/C, Pt-Co and Pt-Pd/C electrocatalysts, prepared by a combined
approach of impregnation and seeding, was performed. According to
the activity test in a single Proton Exchange Membrane (PEM) fuel
cell, the Oxygen Reduction Reaction (ORR) activity of the Pt-M/C
electrocatalyst was slightly lower than that of Pt/C. The j0.9 V and
E10 mA/cm2 of the as-prepared electrocatalysts increased in the order of
Pt/C > Pt-Co/C > Pt-Pd/C. However, in the medium-to-high current
density region, Pt-Pd/C exhibited the best performance. With regard to
their stability in a 0.5 M H2SO4 electrolyte solution, the
electrochemical surface area decreased as the number of rounds of
repetitive potential cycling increased due to the dissolution of the
metals within the catalyst structure. For long-term measurement, Pt-
Pd/C was the most stable than the other three electrocatalysts.
Abstract: This work studies the effect of chemical composition
on the activity and selectivity of γ–alumina supported CuO/
MnO2/Cr2O3 catalysts toward deep oxidation of CO, dimethyl ether
(DME) and methanol. The catalysts were prepared by impregnation
of the support with an aqueous solution of copper nitrate, manganese
nitrate and CrO3 under different conditions. Thermal, XRD and TPR
analysis were performed. The catalytic measurements of single
compounds oxidation were carried out on continuous flow equipment
with a four-channel isothermal stainless steel reactor. Flow-line
equipment with an adiabatic reactor for simultaneous oxidation of all
compounds under the conditions that mimic closely the industrial
ones was used. The reactant and product gases were analyzed by
means of on-line gas chromatographs.
On the basis of XRD analysis it can be concluded that the active
component of the mixed Cu-Mn-Cr/γ–alumina catalysts consists of at
least six compounds – CuO, Cr2O3, MnO2, Cu1.5Mn1.5O4,
Cu1.5Cr1.5O4 and CuCr2O4, depending on the Cu/Mn/Cr molar ratio.
Chemical composition strongly influences catalytic properties, this
influence being quite variable with regards to the different processes.
The rate of CO oxidation rapidly decrease with increasing of
chromium content in the active component while for the DME was
observed the reverse trend. It was concluded that the best
compromise are the catalysts with Cu/(Mn + Cr) molar ratio 1:5 and
Mn/Cr molar ratio from 1:3 to 1:4.
Abstract: Currently, continuous two-phase decanter process
used for olive oil production is the more internationally widespread.
The wastewaters generated from this industry (OMW) are a real
environmental problem because of its high organic load. Among
proposed treatments for these wastewaters, advanced oxidation
technologies (Fenton, ozone, photoFenton, etc.) are the most
favourable. The direct application of these processes is somewhat
expensive. Therefore, the application of a previous stage based on a
flocculation-sedimentation operation is of high importance. In this
research five commercial flocculants (three cationic, and two anionic)
have been used to achieve the separation of phases (liquid clarifiedsludge).
For each flocculant, different concentrations (0-1000 mg/L)
have been studied. In these experiments, sludge volume formed and
the final water quality were determined. The final removal
percentages of total phenols (11.3-25.1%), COD (5.6-20.4%), total
carbon (2.3-26.5%), total organic carbon (1.50-23.8%), total nitrogen
(1.45-24.8%), and turbidity (27.9-61.4%) were determined. The
variation on electric conductivity reduction percentage (1-8%) was
also determined. Finally, the best flocculants with highest removal
percentages have been determined (QG2001 and Flocudex CS49).
Abstract: This paper aims to study the effect of cold work
condition on the microstructure of Cu-1.5wt%Ti, and Cu-3.5wt%Ti
and hence mechanical properties. The samples under investigation
were machined, and solution heat treated. X-ray diffraction technique
is used to identify the different phases present after cold deformation
by compression and also different heat treatment and also measuring
the relative quantities of phases present. The metallographic
examination is used to study the microstructure of the samples. The
hardness measurements were used to indicate the change in
mechanical properties. The results are compared with the mechanical
properties obtained by previous workers. Experiments on cold
compression followed by aging of Cu-Ti alloys have indicated that
the most efficient hardening of the material results from continuous
precipitation of very fine particles within the matrix. These particles
were reported to be β`-type, Cu4Ti phase. The β`-β transformation
and particles coarsening within the matrix as well as long grain
boundaries were responsible for the overaging of Cu-1.5wt%Ti and
Cu-3.5wt%Ti alloys. It is well known that plate-like particles are β –
type, Cu3Ti phase. Discontinuous precipitation was found to start at
the grain boundaries and expand into grain interior. At the higher
aging temperature, a classic Widmanstätten morphology forms giving
rise to a coarse microstructure comprised of α and the equilibrium
phase β. Those results were confirmed by X-ray analysis, which
found that a few percent of Cu3Ti, β precipitates are formed during
aging at high temperature for long time for both Cu- Ti alloys (i.e.
Cu-1.5wt%Ti and Cu-3.5wt%Ti).