Abstract: This study focuses on the effect of pin taper tool ratio on friction stir welding of magnesium alloy AZ31. Two pieces of AZ31 alloy with thickness of 6 mm were friction stir welded by using the conventional milling machine. The shoulder diameter used in this experiment is fixed at 18 mm. The taper pin ratio used are varied at 6:6, 6:5, 6:4, 6:3, 6:2 and 6:1. The rotational speeds that were used in this study were 500 rpm, 1000 rpm and 1500 rpm, respectively. The welding speeds used are 150 mm/min, 200 mm/min and 250 mm/min. Microstructure observation of welded area was studied by using optical microscope. Equiaxed grains were observed at the TMAZ and stir zone indicating fully plastic deformation. Tool pin diameter ratio 6/1 causes low heat input to the material because of small contact surface between tool surface and stirred materials compared to other tool pin diameter ratio. The grain size of stir zone increased with increasing of ratio of rotational speed to transverse speed due to higher heat input. It is observed that worm hole is produced when excessive heat input is applied. To evaluate the mechanical properties of this specimen, tensile test was used in this study. Welded specimens using taper pin ratio 6:1 shows higher tensile strength compared to other taper pin ratio up to 204 MPa. Moreover, specimens using taper pin ratio 6:1 showed better tensile strength with 500 rpm of rotational speed and 150mm/min welding speed.
Abstract: Study of the effects of climate change on Norway
Spruce (Picea abies) forests has mainly focused on the diversity of
tree species diversity of tree species as a result of the ability of
species to tolerate temperature and moisture changes as well as some
effects of disturbance regime changes. The tree species’ diversity
changes in spruce forests due to climate change have been analyzed
via gap model. Forest gap model is a dynamic model for calculation
basic characteristics of individual forest trees. Input ecological data
for model calculations have been taken from the permanent research
plots located in primeval forests in mountainous regions in Slovakia.
The results of regional scenarios of the climatic change for the
territory of Slovakia have been used, from which the values are
according to the CGCM3.1 (global) model, KNMI and MPI
(regional) models. Model results for conditions of the climate change
scenarios suggest a shift of the upper forest limit to the region of the
present subalpine zone, in supramontane zone. N. spruce
representation will decrease at the expense of beech and precious
broadleaved species (Acer sp., Sorbus sp., Fraxinus sp.). The most
significant tree species diversity changes have been identified for the
upper tree line and current belt of dwarf pine (Pinus mugo)
occurrence. The results have been also discussed in relation to most
important disturbances (wind storms, snow and ice storms) and
phenological changes which consequences are little known. Special
discussion is focused on biomass production changes in relation to
carbon storage diversity in different carbon pools.
Abstract: This paper takes a philosophical view as axiom, and
reveals the relationship between information theory and Natural
Intelligence and Artificial Intelligence under real world conditions.
This paper also derives the relationship between natural intelligence
and nature. According to communication principle of information
theory, Natural Intelligence can be divided into real part and virtual
part. Based on information theory principle that Information does not
increase, the restriction mechanism of Natural Intelligence creativity is
conducted. The restriction mechanism of creativity reveals the limit of
natural intelligence and artificial intelligence. The paper provides a
new angle to observe natural intelligence and artificial intelligence.
Abstract: Social entrepreneurship is a new and exciting topic
that holds a great promise in helping alleviate the social problems of
the world. As a new subject, the meaning of the term is too broad and
this is counterproductive in trying to build understanding around the
concept. The purpose of this study is to identify and compare the
elements of social entrepreneurship as defined by seven international
organizations leading social entrepreneurship projects: Ashoka
Foundation, Skoll Foundation, Schwab Foundation and Yunus
Center; as well as from three other institutions fostering social
entrepreneurship: Global Social Benefit Institute, BRAC University,
and Socialab. The study used document analysis from Skoll
Foundation, Schwab Foundation, Yunus Center and Ashoka
Foundation; and open ended interview to experts from the Global
Social Benefit Institute at Santa Clara University in United States,
BRAC University from Bangladesh, and Socialab from Argentina.
The study identified three clearly differentiated schools of thought,
based on their views on revenue, scalability, replicability and
geographic location. While this study is by no means exhaustive, it
provides an indication of the patterns of ideas fostered by important
players in the field. By clearly identifying the similarities and
differences in the concept of social entrepreneurship, research and
practitioners are better equipped to build on the subject, and to
promote more adequate and accurate social policies to foster the
development of social entrepreneurship.
Abstract: This paper presents the trajectory tracking control of a
spatial redundant hybrid manipulator. This manipulator consists of
two parallel manipulators which are a variable geometry truss (VGT)
module. In fact, each VGT module with 3-degress of freedom (DOF)
is a planar parallel manipulator and their operational planes of these
VGT modules are arranged to be orthogonal to each other. Also, the
manipulator contains a twist motion part attached to the top of the
second VGT module to supply the missing orientation of the endeffector.
These three modules constitute totally 7-DOF hybrid
(parallel-parallel) redundant spatial manipulator. The forward
kinematics equations of this manipulator are obtained, then,
according to these equations, the inverse kinematics is solved based
on an optimization with the joint limit avoidance. The dynamic
equations are formed by using virtual work method. In order to test
the performance of the redundant manipulator and the controllers
presented, two different desired trajectories are followed by using the
computed force control method and a switching control method. The
switching control method is combined with the computed force
control method and genetic algorithm. In the switching control
method, the genetic algorithm is only used for fine tuning in the
compensation of the trajectory tracking errors.
Abstract: Within Vietnam's system of higher education, its
schools of business play a vital role in supporting the country’s
economic objectives. However, the crucial contribution of soft skills
for maximal success within the business sector has to date not been
adequately recognized by its business schools. This being so, the
development of the business school curriculum in Vietnam has not
been able to 'catch up', so to say, with the burgeoning need of
students for a comprehensive soft skills program designed to meet the
national and global business objectives of their potential employers.
The burden of the present paper is first to reveal the results of our
survey in Vietnam which make explicit the extent to which major
Vietnamese industrial employers’ value the potential role that soft
skill competencies can play in maximizing business success. Our
final task will be to determine which soft skills employers discern as
best serving to maximize the economic interests of Vietnam within
the global marketplace. Semi-structured telephone interviews have
been conducted with the 15 representative Head Employers of
Vietnam's reputedly largest and most successful of the diverse
business enterprises across Vietnam. The findings of the study
indicate that all respondents highly value the increasing importance
of soft skills in business success. Our critical analysis of respondent
data reveals that 19 essential soft skills are deemed by employers as
integral to business workplace efficacy and should thus be integrated
into the formal business curriculum. We are confident that our study
represents the first comprehensive and specific survey yet undertaken
within the business sector in Vietnam which accesses and analyses
the opinions of representative employers from major companies
across the country in regard to the growing importance of 19 specific
soft skills essential for maximizing overall business success. Our
research findings also reveal that the integration into business school
curriculums nationwide of the soft skills we have identified is of
paramount importance to advance the national and global economic
interests of Vietnam.
Abstract: Connected vehicles are equipped with wireless sensors
that aid in Vehicle to Vehicle (V2V) and Vehicle to Infrastructure
(V2I) communication. These vehicles will in the near future
provide road safety, improve transport efficiency, and reduce traffic
congestion. One of the challenges for connected vehicles is how
to ensure that information sent across the network is secure. If
security of the network is not guaranteed, several attacks can occur,
thereby compromising the robustness, reliability, and efficiency of
the network. This paper discusses existing security mechanisms and
unique properties of connected vehicles. The methodology employed
in this work is exploratory. The paper reviews existing security
solutions for connected vehicles. More concretely, it discusses
various cryptographic mechanisms available, and suggests areas
of improvement. The study proposes a combination of symmetric
key encryption and public key cryptography to improve security.
The study further proposes message aggregation as a technique to
overcome message redundancy. This paper offers a comprehensive
overview of connected vehicles technology, its applications, its
security mechanisms, open challenges, and potential areas of future
research.
Abstract: The technological paradigm of the disaster
management field, especially in the case of governmental
intervention strategies, is generally based on rapid and flexible
accommodation solutions. From various technical solution patterns
used to address the immediate housing needs of disaster victims, the
adaptive re-use of existing buildings can be considered to be both
low-cost and practical. However, there is a scarcity of analytical
methods to screen, select and adapt buildings to help decision makers
in cases of emergency. Following an extensive literature review, this
paper aims to highlight key points and problem areas associated with
the adaptive re-use of buildings within the disaster management
context. In other disciplines such as real estate management, the
adaptive re-use potential (ARP) of existing buildings is typically
based on the prioritization of a set of technical and non-technical
criteria which are then weighted to arrive at an economically viable
investment decision. After a disaster, however, the assessment of the
ARP of buildings requires consideration of different/additional layers
of analysis which stem from general disaster management principles
and the peculiarities of different types of disasters, as well as of their
victims. In this paper, a discussion of the development of an adaptive
re-use potential (ARP) assessment model is presented. It is thought
that governmental and non-governmental decision makers who are
required to take quick decisions to accommodate displaced masses
following disasters are likely to benefit from the implementation of
such a model.
Abstract: Imazu Bay plays an important role for endangered
species such as horseshoe crabs and black-faced spoonbills that stay in
the bay for spawning or the passing of winter. However, this bay is
semi-enclosed with slow water exchange, which could lead to
eutrophication under the condition of excess nutrient inflow to the bay.
Therefore, quantification of nutrient inflow is of great importance.
Generally, analysis of nutrient inflow to the bays takes into
consideration nutrient inflow from only the river, but that from
groundwater should not be ignored for more accurate results. The main
objective of this study is to estimate the amounts of nutrient inflow
from river and groundwater to Imazu Bay by analyzing water budget
in Zuibaiji River Basin and loads of T-N, T-P, NO3-N and NH4-N. The
water budget computation in the basin is performed using groundwater
recharge model and quasi three-dimensional two-phase groundwater
flow model, and the multiplication of the measured amount of nutrient
inflow with the computed discharge gives the total amount of nutrient
inflow to the bay. In addition, in order to evaluate nutrient inflow to the
bay, the result is compared with nutrient inflow from geologically
similar river basins. The result shows that the discharge is 3.50×107
m3/year from the river and 1.04×107 m3/year from groundwater. The
submarine groundwater discharge accounts for approximately 23 % of
the total discharge, which is large compared to the other river basins. It
is also revealed that the total nutrient inflow is not particularly large.
The sum of NO3-N and NH4-N loadings from groundwater is less than
10 % of that from the river because of denitrification in groundwater.
The Shin Seibu Sewage Treatment Plant located below the observation
points discharges treated water of 15,400 m3/day and plans to increase
it. However, the loads of T-N and T-P from the treatment plant are 3.9
mg/L and 0.19 mg/L, so that it does not contribute a lot to
eutrophication.
Abstract: This study was designed to evaluate whether carvacrol
(CAR) could provide protection against lung injury by acute
pancreatitis development. The rats were randomized into groups to
receive (I) no therapy; (II) 50 μg/kg cerulein at 1h intervals by four
intraperitoneal injections (i.p.); (III) 50, 100 and 200 mg/kg CAR by
one i.p.; and (IV) cerulein+CAR after 2h of cerulein injection. 12h
later, serum samples were obtained to assess pancreatic function the
lipase and amylase values. The animals were euthanized and lung
samples were excised. The specimens were stained with
hematoxylin-eosin (H&E), periodic acid–Schif (PAS), Mallory's
trichrome and amyloid. Additionally, oxidative DNA damage was
determined by measuring as increases in 8-hydroxy-deoxyguanosine
(8-OH-dG) adducts. The results showed that the serum activity of
lipase and amylase in AP rats were significantly reduced after the
therapy (p
Abstract: The housing industry is crucial for sustainable
development of every country. Housing is a basic need that can
enhance the quality of life. Owning a house is therefore the main aim
of individuals. However, affordability has become a critical issue
towards homeownership. In recent years, housing price in the main
cities has increased tremendously to unaffordable level. This paper
investigates factors influencing the housing price from developer’s
perspective and provides recommendation on strategies to tackle this
issue. Online and face-to-face survey was conducted on housing
developers operating in Penang, Malaysia. The results indicate that
(1) location; (2) macroeconomics factor; (3) demographic factors; (4)
land/zoning and; (5) industry factors are the main factors influencing
the housing price. This paper contributes towards better
understanding on developers’ view on how the housing price is
determined and form a basis for government to help tackle the
housing affordability issue.
Abstract: There is an increasing demand for developing urban
land to provide better living conditions for all citizens in Afghanistan.
Most of the development will involve the acquisition of land. And the
current land acquisition method practiced by central government is
expropriation, which is a cash-based transaction method that imposes
heavy fiscal burden on local municipalities and central government,
and it does not protect ownership rights and social equity of
landowners besides it relocates the urban poor to remote areas with
limited access to jobs and public services. The questionnaire analysis,
backed by observations of different case studies in countries where
land readjustment is used as a collaborative land development tool
indicates that the method plays a key role in valuing landowners’
rights, giving other community members and stakeholders the
opportunity to collaboratively implement urban development
projects. The practice of the method is reducing the heavy fiscal
burden on the local and central governments and is a better option to
deal with the current development challenges in Afghanistan.
Abstract: Waste polyethylene (PE) is classified as waste low
density polyethylene (LDPE) and waste high density polyethylene
(HDPE) according to their densities. Pyrolysis of plastic waste may
have an important role in dealing with the enormous amounts of
plastic waste produced all over the world, by decreasing their
negative impact on the environment. This waste may be converted
into economically valuable hydrocarbons, which can be used both as
fuels and as feed stock in the petrochemical industry. End product
yields and properties depend on the plastic waste composition.
Pyrolytic biochar is one of the most important products of waste
plastics pyrolysis. In this study, HDPE and LDPE plastic wastes were
co-pyrolyzed together with waste olive pomace. Pyrolysis runs were
performed at temperature 700°C with heating rates of 5°C/min.
Higher pyrolysis oil and gas yields were observed by the using waste
olive pomace. The biochar yields of HDPE- olive pomace and LDPEolive
pomace were 6.37% and 7.26% respectively for 50% olive
pomace doses. The calorific value of HDPE-olive pomace and
LDPE-olive pomace of pyrolysis oil were 8350 and 8495 kCal.
Abstract: The main purposes of this study are to develop a scale
that reflects emerging theoretical understandings of new media
credibility, based on the evolution of credibility studies in western
researches, identification of the determinants of credibility in the
media and its components by comparing traditional and new media
credibility scales and building accumulative scale to test new media
credibility. This approach was built on western researches using
conceptualizations of media credibility, which focuses on four
principal components: Source (journalist), message (article), medium
(newspaper, radio, TV, web, etc.), and organization (owner of the
medium), and adding user and cultural context as key components to
assess new media credibility in particular. This study’s value lies in
its contribution to the conceptualization and development of new
media credibility through the creation of a theoretical measurement
tool. Future studies should explore this scale to test new media
credibility, which represents a promising new approach in the efforts
to define and measure credibility of all media types.
Abstract: The idea of cropping-system is a method used by
farmers. It is an environmentally-friendly method, protecting the
natural resources (soil, water, air, nutritive substances) and increase
the production at the same time, taking into account some crop
particularities. The combination of this powerful method with the
concepts of genetic algorithms results into a possibility of generating
sequences of crops in order to form a rotation. The usage of this type
of algorithms has been efficient in solving problems related to
optimization and their polynomial complexity allows them to be used
at solving more difficult and various problems. In our case, the
optimization consists in finding the most profitable rotation of
cultures. One of the expected results is to optimize the usage of the
resources, in order to minimize the costs and maximize the profit. In
order to achieve these goals, a genetic algorithm was designed. This
algorithm ensures the finding of several optimized solutions of
cropping-systems possibilities which have the highest profit and,
thus, which minimize the costs. The algorithm uses genetic-based
methods (mutation, crossover) and structures (genes, chromosomes).
A cropping-system possibility will be considered a chromosome and
a crop within the rotation is a gene within a chromosome. Results
about the efficiency of this method will be presented in a special
section. The implementation of this method would bring benefits into
the activity of the farmers by giving them hints and helping them to
use the resources efficiently.
Abstract: The aim of the paper is to investigate the effect of
corporate social responsibility (CSR) CSR on the National
Commercial Bank (NCB) in Saudi Arabia. In order to achieve this, a
case study was made of the CSR activities of this bank from the
perspective of its branch managers. The NCB was chosen as it was
one of the first Saudi banks to engage in CSR and currently has a
wide range of CSR initiatives. A qualitative research method was
used. Open-ended questionnaires were administered to eighty branch
managers of the NCB, with fifty-five usable questionnaires returned
and twenty managers were interviewed as part of the primary
research. Data from both questionnaires and interviews were
analysed using qualitative content analysis. Six themes emerged from
the questionnaire findings were used to develop the interview
questions. These themes are the following: Awareness of employees
about CSR in the NCB; CSR activities as a type of investment;
Government and media support; Increased employee loyalty in the
NCB; Prestige and profit to the NCB; and View of CSR in Islam.
This paper makes a theoretical contribution in that it investigates and
increases understanding of the effect of CSR on the NCB in Saudi
Arabia. In addition, it makes a practical contribution by making
recommendations which can support the development of CSR in the
NCB. A limitation of the paper is that it is a case study of only one
bank. It is therefore recommended that future research could be
conducted with other banks in Saudi Arabia, or indeed, with a range
of other types of firm within the financial services area in Saudi
Arabia. In this way, the same issues could be explored but with a
greater potential generalisability of findings of CSR within the Saudi
Arabian financial services industry. In addition, this paper takes a
qualitative approach and it is suggested that future research be carried
out using mixed methods, which could provide a greater depth of
analysis.
Abstract: This study presents an inverse analysis for predicting the thermal conductivities and the heat flux of a high-temperature metallurgical reactor simultaneously. Once these thermal parameters are predicted, the time-varying thickness of the protective phase-change bank that covers the inside surface of the brick walls of a metallurgical reactor can be calculated. The enthalpy method is used to solve the melting/solidification process of the protective bank. The inverse model rests on the Levenberg-Marquardt Method (LMM) combined with the Broyden method (BM). A statistical analysis for the thermal parameter estimation is carried out. The effect of the position of the temperature sensors, total number of measurements and measurement noise on the accuracy of inverse predictions is investigated. Recommendations are made concerning the location of temperature sensors.
Abstract: Broadband Wireless Network (BWN) is the promising technology nowadays due to the increased number of smartphones. Buffering scheme using network coding considers the reliability and proper degree distribution in Worldwide interoperability for Microwave Access (WiMAX) multi-hop network. Using network coding, a secure way of transmission is performed which helps in improving throughput and reduces the packet loss in the multicast network. At the outset, improved network coding is proposed in multicast wireless mesh network. Considering the problem of performance overhead, degree distribution makes a decision while performing buffer in the encoding / decoding process. Consequently, BuS (Buffer Scheme) based on network coding is proposed in the multi-hop network. Here the encoding process introduces buffer for temporary storage to transmit packets with proper degree distribution. The simulation results depend on the number of packets received in the encoding/decoding with proper degree distribution using buffering scheme.
Abstract: In an economic crisis such as the one that shook (and still shake) Europe, one does not question the importance of the measures that encourage the hiring and integration of young people into the labour market. In the mentioned context, enterprises tend to reduce the cost of labour and to seek flexible contracting instruments. The professional internships allow innovation and creativity at low cost, because, as they are not labour contracts, the enterprises do not have to respect the minimum standards related to wages, working time duration and so on. In Portugal, we observe a widespread existence of training contracts in which the trainee worked several hours without salary or was paid below the legally prescribed for the function and the work period. For this reason, under the tripartite agreement for a new system of regulation of labour relations, employment policies and social protection, between the Government and the social partners, in June 2008, foresaw a prohibition of professional internships unpaid and the legal regulation of the mandatory internships for access to an activity. The first Act about private internship contracts, i.e., internships without public funding was embodied in the Decree-Law N. 66/2011, of 1st June. This work is dedicated to the study of the legal regime of the internship contract in Portugal, by analysing the problems brought by the new set of rules and especially those which remains unresolved. In fact, we can conclude that the number of situations covered by the Act is much lower than what was expected, because of the exclusion of the mandatory internship for access to a profession when the activity is developed autonomously. Since the majority of the activities can be developed both autonomously or subordinated, it is quite easy to out of the Act requirements and, so, out of the protection that it confers to the intern. In order to complete this study, we considered not only the mentioned legal Act, but also the few doctrine and jurisprudence about the theme.
Abstract: With the increasing complexity of cyberspace security, the cyber-attack attribution has become an important challenge of the security protection systems. The difficult points of cyber-attack attribution were forced on the problems of huge data handling and key data missing. According to this situation, this paper presented a reasoning method of cyber-attack attribution based on threat intelligence. The method utilizes the intrusion kill chain model and Bayesian network to build attack chain and evidence chain of cyber-attack on threat intelligence platform through data calculation, analysis and reasoning. Then, we used a number of cyber-attack events which we have observed and analyzed to test the reasoning method and demo system, the result of testing indicates that the reasoning method can provide certain help in cyber-attack attribution.