Abstract: Sensor relocation is to repair coverage holes caused by node failures. One way to repair coverage holes is to find redundant nodes to replace faulty nodes. Most researches took a long time to find redundant nodes since they randomly scattered redundant nodes around the sensing field. To record the precise position of sensor nodes, most researches assumed that GPS was installed in sensor nodes. However, high costs and power-consumptions of GPS are heavy burdens for sensor nodes. Thus, we propose a fast sensor relocation algorithm to arrange redundant nodes to form redundant walls without GPS. Redundant walls are constructed in the position where the average distance to each sensor node is the shortest. Redundant walls can guide sensor nodes to find redundant nodes in the minimum time. Simulation results show that our algorithm can find the proper redundant node in the minimum time and reduce the relocation time with low message complexity.
Abstract: This paper presents a methodology to harvest the kinetic energy of the raindrops using piezoelectric devices. In the study 1m×1m PVDF (Polyvinylidene fluoride) piezoelectric membrane, which is fixed by the four edges, is considered for the numerical simulation on deformation of the membrane due to the impact of the raindrops. Then according to the drop size of the rain, the simulation is performed classifying the rainfall types into three categories as light stratiform rain, moderate stratiform rain and heavy thundershower. The impact force of the raindrop is dependent on the terminal velocity of the raindrop, which is a function of raindrop diameter. The results were then analyzed to calculate the harvestable energy from the deformation of the piezoelectric membrane.
Abstract: Network on Chip (NoC) has emerged as a promising
on chip communication infrastructure. Three Dimensional Integrate
Circuit (3D IC) provides small interconnection length between layers
and the interconnect scalability in the third dimension, which can
further improve the performance of NoC. Therefore, in this paper,
a hierarchical cluster-based interconnect architecture is merged with
the 3D IC. This interconnect architecture significantly reduces the
number of long wires. Since this architecture only has approximately
a quarter of routers in 3D mesh-based architecture, the average
number of hops is smaller, which leads to lower latency and higher
throughput. Moreover, smaller number of routers decreases the area
overhead. Meanwhile, some dual links are inserted into the bottlenecks
of communication to improve the performance of NoC.
Simulation results demonstrate our theoretical analysis and show the
advantages of our proposed architecture in latency, throughput and
area, when compared with 3D mesh-based architecture.
Abstract: A robust wheel slip controller for electric vehicles is
introduced. The proposed wheel slip controller exploits the dynamics
of electric traction drives and conventional hydraulic brakes for
achieving maximum energy efficiency and driving safety. Due to
the control of single wheel traction motors in combination with a
hydraulic braking system, it can be shown, that energy recuperation
and vehicle stability control can be realized simultaneously. The
derivation of a sliding mode wheel slip controller accessing two
drivetrain actuators is outlined and a comparison to a conventionally
braked vehicle is shown by means of simulation.
Abstract: Petri Net (PN) has proven to be effective graphical, mathematical, simulation, and control tool for Discrete Event Systems (DES). But, with the growth in the complexity of modern industrial, and communication systems, PN found themselves inadequate to address the problems of uncertainty, and imprecision in data. This gave rise to amalgamation of Fuzzy logic with Petri nets and a new tool emerged with the name of Fuzzy Petri Nets (FPN). Although there had been a lot of research done on FPN and a number of their applications have been anticipated, but their basic types and structure are still ambiguous. Therefore, in this research, an effort is made to categorize FPN according to their structure and algorithms Further, literature review of the applications of FPN in the light of their classifications has been done.
Abstract: In this work, we perform numerical simulation of fluid
mixing in a floor-grooved micro-channel with wavy sidewalls which
may impose perturbation on the helical flow induced by the slanted
grooves on the channel floor. The perturbation is caused by separation
vortices in the recesses of the wavy-walled channel as the Reynolds
number is large enough. The results show that the effects of the wavy
sidewalls of the present micromixer on the enhancement of fluid
mixing increase with the increase of Reynolds number. The degree of
mixing increases with the increase of the corrugation angle, until the
angle is greater than 45 degrees. Besides, the pumping pressure of the
micromixer increases with the increase of the corrugation angle
monotonically. Therefore, we would suggest setting the corrugation
angle of the wavy sidewalls to be 45 degrees.
Abstract: In this paper, we present a novel technique called Self-Learning Expert System (SLES). Unlike Expert System, where there is a need for an expert to impart experiences and knowledge to create the knowledge base, this technique tries to acquire the experience and knowledge automatically. To display this technique at work, a simulation of a mobile robot navigating through an environment with obstacles is employed using visual basic. The mobile robot will move through this area without colliding with any obstacle and save the path that it took. If the mobile robot has to go through a similar environment again, then it will apply this experience to help it move through quicker without having to check for collision.
Abstract: The present study is concerned with effect of exciting
boundary layer on increase in heat transfer from flat surfaces. As any
increase in heat transfer between a fluid inside a face and another one
outside of it can cause an increase in some equipment's efficiency, so
at this present we have tried to increase the wall's heat transfer
coefficient by exciting the fluid boundary layer. By a collision
between flow and the placed block at the fluid way, the flow pattern
and the boundary layer stability will change. The flow way inside the
channel is simulated as a 2&3-dimensional channel by Gambit
TM
software.
With studying the achieved results by this simulation for the flow
way inside the channel with a block coordinating with Fluent
TM
software, it's determined that the figure and dimensions of the exciter
are too important for exciting the boundary layer so that any increase
in block dimensions in vertical side against the flow and any
reduction in its dimensions at the flow side can increase the average
heat transfer coefficient from flat surface and increase the flow
pressure loss. Using 2&3-dimensional analysis on exciting the flow at
the flow way inside a channel by cylindrical block at the same time
with the external flow, we came to this conclusion that the heat flux
transferred from the surface, is increased considerably in terms of the
condition without excitation. Also, the k-e turbulence model is used.
Abstract: Supply Chain Management (SCM) is the integration
between manufacturer, transporter and customer in order to form one
seamless chain that allows smooth flow of raw materials, information
and products throughout the entire network that help in minimizing
all related efforts and costs. The main objective of this paper is to
develop a model that can accept a specified number of spare-parts
within the supply chain, simulating its inventory operations
throughout all stages in order to minimize the inventory holding
costs, base-stock, safety-stock, and to find the optimum quantity of
inventory levels, thereby suggesting a way forward to adapt some
factors of Just-In-Time to minimizing the inventory costs throughout
the entire supply chain. The model has been developed using Micro-
Soft Excel & Visual Basic in order to study inventory allocations in
any network of the supply chain. The application and reproducibility
of this model were tested by comparing the actual system that was
implemented in the case study with the results of the developed
model. The findings showed that the total inventory costs of the
developed model are about 50% less than the actual costs of the
inventory items within the case study.
Abstract: This paper presents a hybrid approach for solving nqueen problem by combination of PSO and SA. PSO is a population based heuristic method that sometimes traps in local maximum. To solve this problem we can use SA. Although SA suffer from many iterations and long time convergence for solving some problems, By good adjusting initial parameters such as temperature and the length of temperature stages SA guarantees convergence. In this article we use discrete PSO (due to nature of n-queen problem) to achieve a good local maximum. Then we use SA to escape from local maximum. The experimental results show that our hybrid method in comparison of SA method converges to result faster, especially for high dimensions n-queen problems.
Abstract: This work presents an approach for the measurement
of mutual inductance on near field inductive coupling. The mutual
inductance between inductive circuits allows the simulation of energy
transfer from reader to tag, that can be used in RFID and powerless
implantable devices. It also allows one to predict the maximum
voltage in the tag of the radio-frequency system.
Abstract: The wireless sensor networks have been extensively
deployed and researched. One of the major issues in wireless sensor
networks is a developing energy-efficient clustering protocol.
Clustering algorithm provides an effective way to prolong the lifetime
of a wireless sensor networks. In the paper, we compare several
clustering protocols which significantly affect a balancing of energy
consumption. And we propose an Energy-Efficient Distributed
Unequal Clustering (EEDUC) algorithm which provides a new way of
creating distributed clusters. In EEDUC, each sensor node sets the
waiting time. This waiting time is considered as a function of residual
energy, number of neighborhood nodes. EEDUC uses waiting time to
distribute cluster heads. We also propose an unequal clustering
mechanism to solve the hot-spot problem. Simulation results show that
EEDUC distributes the cluster heads, balances the energy
consumption well among the cluster heads and increases the network
lifetime.
Abstract: This paper proposes a methodology for analysis of
the dynamic behavior of a robotic manipulator in continuous
time. Initially this system (nonlinear system) will be decomposed
into linear submodels and analyzed in the context of the Linear
and Parameter Varying (LPV) Systems. The obtained linear
submodels, which represent the local dynamic behavior of the
robotic manipulator in some operating points were grouped in
a Takagi-Sugeno fuzzy structure. The obtained fuzzy model was
analyzed and validated through analog simulation, as universal
approximator of the robotic manipulator.
Abstract: Electromyography (EMG) is the study of muscles function through analysis of electrical activity produced from muscles. This electrical activity which is displayed in the form of signal is the result of neuromuscular activation associated with muscle contraction. The most common techniques of EMG signal recording are by using surface and needle/wire electrode where the latter is usually used for interest in deep muscle. This paper will focus on surface electromyogram (SEMG) signal. During SEMG recording, several problems had to been countered such as noise, motion artifact and signal instability. Thus, various signal processing techniques had been implemented to produce a reliable signal for analysis. SEMG signal finds broad application particularly in biomedical field. It had been analyzed and studied for various interests such as neuromuscular disease, enhancement of muscular function and human-computer interface.
Abstract: This paper discusses the novel graphical approach for
stability analysis of multi induction motor drive controlled by a single
inverter. Stability issue arises in parallel connected induction motors
under unbalanced load conditions. The two powerful globally
accepted modeling and simulation software packages such as
MATLAB and LabVIEW are selected to perform the stability
analysis. The stability investigation is performed for different load
conditions and difference in stator and rotor resistances among the
two motors. It is very simple and effective than the techniques
presented to obtain the stability of the parallel connected induction
motor drive under unbalanced load conditions. Approximate transfer
functions are considered to model the induction motors, load
dynamics, speed controllers and inverter. Simulink library tools are
utilized to model the entire drive scheme in MATLAB. Stability
study is discussed in LabVIEW using control design and simulation
toolkits. Simulation results are illustrated for various running
conditions to demonstrate the effectiveness of the transfer function
method.
Abstract: Most of the real queuing systems include special properties and constraints, which can not be analyzed directly by using the results of solved classical queuing models. Lack of Markov chains features, unexponential patterns and service constraints, are the mentioned conditions. This paper represents an applied general algorithm for analysis and optimizing the queuing systems. The algorithm stages are described through a real case study. It is consisted of an almost completed non-Markov system with limited number of customers and capacities as well as lots of common exception of real queuing networks. Simulation is used for optimizing this system. So introduced stages over the following article include primary modeling, determining queuing system kinds, index defining, statistical analysis and goodness of fit test, validation of model and optimizing methods of system with simulation.
Abstract: In this paper, a alternative structure method for
continuous time sigma delta modulator is presented. In this
modulator for implementation of integrators in loop filter second
generation current conveyors are employed. The modulator is
designed in CMOS technology and features low power consumption
(65db),
and with 180khZ bandwidth. Simulation results confirm that this
design is suitable for data converters.
Abstract: In Image processing the Image compression can improve
the performance of the digital systems by reducing the cost and
time in image storage and transmission without significant reduction
of the Image quality. This paper describes hardware architecture of
low complexity Discrete Cosine Transform (DCT) architecture for
image compression[6]. In this DCT architecture, common computations
are identified and shared to remove redundant computations
in DCT matrix operation. Vector processing is a method used for
implementation of DCT. This reduction in computational complexity
of 2D DCT reduces power consumption. The 2D DCT is performed
on 8x8 matrix using two 1-Dimensional Discrete cosine transform
blocks and a transposition memory [7]. Inverse discrete cosine
transform (IDCT) is performed to obtain the image matrix and
reconstruct the original image. The proposed image compression
algorithm is comprehended using MATLAB code. The VLSI design
of the architecture is implemented Using Verilog HDL. The proposed
hardware architecture for image compression employing DCT was
synthesized using RTL complier and it was mapped using 180nm
standard cells. . The Simulation is done using Modelsim. The
simulation results from MATLAB and Verilog HDL are compared.
Detailed analysis for power and area was done using RTL compiler
from CADENCE. Power consumption of DCT core is reduced to
1.027mW with minimum area[1].
Abstract: This paper describes a three-dimensional thermal
model of the current path included in the low voltage power circuit
breakers. The model can be used to analyse the thermal behaviour of
the current path during both steady-state and transient conditions.
The current path lengthwise temperature distribution and timecurrent
characteristic of the terminal connections of the power circuit
breaker have been obtained. The influence of the electric current and
voltage drop on main electric contact of the circuit breaker has been
investigated. To validate the three-dimensional thermal model, some
experimental tests have been done. There is a good correlation
between experimental and simulation results.
Abstract: An adaptive neural network controller for
autonomous underwater vehicles (AUVs) is presented in this paper.
The AUV model is highly nonlinear because of many factors, such as
hydrodynamic drag, damping, and lift forces, Coriolis and centripetal
forces, gravity and buoyancy forces, as well as forces from thruster.
In this regards, a nonlinear neural network is used to approximate the
nonlinear uncertainties of AUV dynamics, thus overcoming some
limitations of conventional controllers and ensure good performance.
The uniform ultimate boundedness of AUV tracking errors and the
stability of the proposed control system are guaranteed based on
Lyapunov theory. Numerical simulation studies for motion control of
an AUV are performed to demonstrate the effectiveness of the
proposed controller.