Abstract: Present paper describes method of obtaining clay
ceramic foam (CCF) and foam concrete (FC), by direct foaming with
high speed mixer-disperser (HSMD). Three foaming agents (FA) are
compared for the FC and CCF production: SCHÄUMUNGSMITTEL
W 53 FLÜSSIG (Zschimmer & Schwarz Gmbh, Germany), SCF-
1245 (Sika, test sample, Latvia) and FAB-12 (Elade, Latvija). CCF
were obtained at 950, 1000°C, 1150°C and 1150°C firing temperature
and have mechanical compressive strength 1.2, 2.55 and 4.3 MPa and
porosity 79.4, 75.1, 71.6%, respectively. Obtained FC has 6-14 MPa
compressive strength and porosity 44-55%. The goal of this work
was development of a sustainable and durable ceramic cellular
structures using HSMD.
Abstract: This paper proposes techniques like MT CMOS,
POWER GATING, DUAL STACK, GALEOR and LECTOR to
reduce the leakage power. A Full Adder has been designed using
these techniques and power dissipation is calculated and is compared
with general CMOS logic of Full Adder.
Simulation results show the validity of the proposed techniques is
effective to save power dissipation and to increase the speed of
operation of the circuits to a large extent.
Abstract: Ulexite (Na2O.2CaO.5B2O3.16H2O) is boron mineral
that is found in large quantities in the Turkey and world. In this
study, the dissolution of this mineral in the disodium hydrogen
phosphate solutions has been studied. Temperature, concentration,
stirring speed, solid liquid ratio and particle size were selected as
parameters. The experimental results were successfully correlated by
linear regression using Statistica program. Dissolution curves were
evaluated shrinking core models for solid-fluid systems. It was
observed that increase in the reaction temperature and decrease in the
solid/liquid ratio causes an increase the dissolution rate of ulexite.
The activation energy was found to be 63.4 kJ/mol. The leaching of
ulexite was controlled by chemical reaction.
Abstract: High pressure turbine (HPT) blades of DV – 2 jet
engines are made from Ni – based superalloy. This alloy was
originally manufactured in the Soviet Union and referred as ŽS6K.
For improving alloy’s high temperature resistance are blades coated
with Al – Si diffusion layer. A regular operation temperature of HPT
blades vary from 705°C to 750°C depending on jet engine regime.
An overcrossing working temperature range causes degradation of
the protective coating as well as base material which microstructure
is formed by the gamma matrix and strengthening phase gamma
prime (forming small particles in the microstructure). Diffusion
processes inside the material during exposition of the material to high
temperatures causes mainly coarsening of the gamma prime particles,
thus decreasing its strengthening effect. Degradation of the Al – Si
coating caused its thickness growth. All the microstructure changes
and coating layer thickness growth results in decreasing of the turbine
blade operation lifetime.
Abstract: The authors propose the identification, analysis and
prognosis of the quantitative and qualitative evolution of the elderly
population in the functional urban areas. The present paper takes into
account the analysis of some representative indicators (the weight of
the elderly population, ageing index, dynamic index of economic
ageing of productive population etc.) and the elaboration of an
integrated indicator that would help differentiate the population
ageing forms in the 48 functional urban areas that were defined based
on demographic and social-economic criteria for all large and
medium cities in Romania.
Abstract: Indonesian higher education has experienced
significant changes over the last decade. In 1999, the government
published an overall strategy for decentralisation and enhancement of
local autonomy in many sectors, including (higher) education.
Indonesian higher education reforms have forced universities to
restructure their internal university governance to become more
entrepreneurial. These new types of internal university governance
are likely to affect the institutions’ leadership and management. This
paper discusses the approach and findings of a study on the
managerial leadership styles of deans in Indonesian universities. The
study aims to get a better understanding of styles exhibited by deans
manifested in their behaviours. Using the theories of reasoned action
and planned behaviour, in combination with the competing values
framework, a large-scale survey was conducted to gather information
on the deans’ behaviours, attitudes, subjective norms, and perceived
behavioural control. Based on the responses of a sample of 218
deans, the study identifies a number of leadership styles: the Master,
the Competitive Consultant, the Consensual Goal-Setter, the Focused
Team Captain, and the Informed Trust-Builder style. The study
demonstrates that attitudes are the primary determinant of the styles
that were found. Perceived behavioural control is a factor that
explains some managerial leadership styles. By understanding the
attitudes of deans in Indonesian universities, and their leadership
styles, universities can strengthen their management and governance,
and thus improve their effectiveness.
Abstract: In the past few years, the amount of malicious software
increased exponentially and, therefore, machine learning algorithms
became instrumental in identifying clean and malware files through
(semi)-automated classification. When working with very large
datasets, the major challenge is to reach both a very high malware
detection rate and a very low false positive rate. Another challenge
is to minimize the time needed for the machine learning algorithm to
do so. This paper presents a comparative study between different
machine learning techniques such as linear classifiers, ensembles,
decision trees or various hybrids thereof. The training dataset consists
of approximately 2 million clean files and 200.000 infected files,
which is a realistic quantitative mixture. The paper investigates the
above mentioned methods with respect to both their performance
(detection rate and false positive rate) and their practicability.
Abstract: Every year, a considerable amount of money is being
invested on research, mainly in the form of funding allocated to
universities and research institutes. To better distribute the available
funds and to set the most proper R&D investment strategies for the
future, evaluation of the productivity of the funded researchers and
the impact of such funding is crucial. In this paper, using the data on
15 years of journal publications of the NSERC (Natural Sciences and
Engineering research Council of Canada) funded researchers and by
means of bibliometric analysis, the scientific development of the
funded researchers and their scientific collaboration patterns will be
investigated in the period of 1996-2010. According to the results it
seems that there is a positive relation between the average level of
funding and quantity and quality of the scientific output. In addition,
whenever funding allocated to the researchers has increased, the
number of co-authors per paper has also augmented. Hence, the
increase in the level of funding may enable researchers to get
involved in larger projects and/or scientific teams and increase their
scientific output respectively.
Abstract: The objective of present research paper is to highlight
the importance of measuring advertisement effectiveness in print
media and to develop a conceptual model for advertisement
effectiveness. The developed model is based on dimensions on which
advertisement effectiveness depends and on the dimensions which are
used to measure the effectiveness. An in-depth and extensive
literature review is carried out to understand the concept of
advertisement effectiveness and its various determinants in context of
print media. Based on the insights gained, a conceptual framework
for advertisement effectiveness is presented. The model is an attempt
to uncover the relatively less explored area of advertisement
effectiveness in Indian advertising scenario. It is believed that present
work will encourage scholars and academicians to further explore the
area and will offer conceptual assistance and a fresh direction in the
domain of advertisement effectiveness.
Abstract: A total of 115 yeast strains isolated from local cassava
processing wastes were measured for crude protein content. Among
these strains, the strain MSY-2 possessed the highest protein
concentration (>3.5 mg protein/mL). By using molecular
identification tools, it was identified to be a strain of Pichia
kudriavzevii based on similarity of D1/D2 domain of 26S rDNA
region. In this study, to optimize the protein production by MSY-2
strain, Response Surface Methodology (RSM) was applied. The
tested parameters were the carbon content, nitrogen content, and
incubation time. Here, the value of regression coefficient (R2) =
0.7194 could be explained by the model which is high to support the
significance of the model. Under the optimal condition, the protein
content was produced up to 3.77 g per L of the culture and MSY-2
strain contains 66.8 g protein per 100 g of cell dry weight. These
results revealed the plausibility of applying the novel strain of yeast
in single-cell protein production.
Abstract: Turkish migrants constitute the largest group among
people with migration background living in Germany. Turkish
women’s labor market participation is of significant importance for
their social and economic integration to the German society. This
paper thus aims to investigate their labor market positions. Turkish
migrant women participate less in the labor market compared to men,
and are responsible for most of the housework, child care, and elderly
care. This is due to their traditional roles in the family, educational
level, insufficient knowledge of German language, and insufficient
professional experience. We strongly recommend that wide-reaching
integration policies for women are formulated, so as to encourage
participation of not only migrant women but also their husbands,
fathers and/or brothers, and natives.
Abstract: Coal is an important non-renewable energy source of
and can be associated with radioactive elements. In Figueira city,
Paraná state, Brazil, it was recorded high uranium activity near the
coal mine that supplies a local thermoelectric power plant. In this
context, the radon activity (Rn-222, produced by the Ra-226 decay in
the U-238 natural series) was evaluated in groundwater, river water
and effluents produced from the acid mine drainage in the coal reject
dumps. The samples were collected in August 2013 and in February
2014 and analyzed at LABIDRO (Laboratory of Isotope and
Hydrochemistry), UNESP, Rio Claro city, Brazil, using an alpha
spectrometer (AlphaGuard) adjusted to evaluate the mean radon
activity concentration in five cycles of 10 minutes. No radon activity
concentration above 100 Bq.L-1, which was a previous critic value
established by the World Health Organization. The average radon
activity concentration in groundwater was higher than in surface
water and in effluent samples, possibly due to the accumulation of
uranium and radium in the aquifer layers that favors the radon
trapping. The lower value in the river waters can indicate dilution and
the intermediate value in the effluents may indicate radon absorption
in the coal particles of the reject dumps. The results also indicate that
the radon activities in the effluents increase with the sample
acidification, possibly due to the higher radium leaching and the
subsequent radon transport to the drainage flow. The water samples
of Laranjinha River and Ribeirão das Pedras stream, which,
respectively, supply Figueira city and receive the mining effluent,
exhibited higher pH values upstream the mine, reflecting the acid
mine drainage discharge. The radionuclides transport indicates the
importance of monitoring their activity concentration in natural
waters due to the risks that the radioactivity can represent to human
health.
Abstract: The emerging markets of post-USSR countries have
attracted Western multinational companies; however, weak
institutions and unstable host country environments have hindered the
implementation of successful management practices. The Ukrainian
market, in light of recent events, is particularly interesting to study
for its compatibility with Western businesses. This paper focuses on
factors that can facilitate or inhibit the transfer of human resource
management practices from Western headquarters to Ukrainian
subsidiaries. To explain the national context’s effects better, a
business systems approach has been applied to a qualitative study of
16 wholly owned Western subsidiaries, dissecting the reasons for a
weak integration of Western practices in Ukraine. Results show that
underdeveloped institutions have forced companies to develop
additional practices that compensate for national weaknesses, as well
as to adjust to a constantly changing environment. Flexibility and
local responsiveness were observed as vital for success in Ukraine.
Abstract: Grid is an environment with millions of resources
which are dynamic and heterogeneous in nature. A computational
grid is one in which the resources are computing nodes and is meant
for applications that involves larger computations. A scheduling
algorithm is said to be efficient if and only if it performs better
resource allocation even in case of resource failure. Resource
allocation is a tedious issue since it has to consider several
requirements such as system load, processing cost and time, user’s
deadline and resource failure. This work attempts in designing a
resource allocation algorithm which is cost-effective and also targets
at load balancing, fault tolerance and user satisfaction by considering
the above requirements. The proposed Budget Constrained Load
Balancing Fault Tolerant algorithm with user satisfaction (BLBFT)
reduces the schedule makespan, schedule cost and task failure rate
and improves resource utilization. Evaluation of the proposed
BLBFT algorithm is done using Gridsim toolkit and the results are
compared with the algorithms which separately concentrates on all
these factors. The comparison results ensure that the proposed
algorithm works better than its counterparts.
Abstract: An Australian manufacturer has fabricated an
innovative GFRP sandwich panel made from E-glass fiber skin and a
modified phenolic core for structural applications. Debonding, which
refers to separation of skin from the core material in composite
sandwiches, is one of the most common types of damage in
composites. The presence of debonding is of great concern because it
not only severely affects the stiffness but also modifies the dynamic
behaviour of the structure. Generally it is seen that the majority of
research carried out has been concerned about the delamination of
laminated structures whereas skin-core debonding has received
relatively minor attention. Furthermore it is observed that research
done on composite slabs having multiple skin-core debonding is very
limited. To address this gap, a comprehensive research investigating
dynamic behaviour of composite panels with single and multiple
debonding is presented. The study uses finite-element modelling and
analyses for investigating the influence of debonding on free
vibration behaviour of single and multilayer composite sandwich
panels. A broad parametric investigation has been carried out by
varying debonding locations, debonding sizes and support conditions
of the panels in view of both single and multiple debonding.
Numerical models were developed with Strand7 finite element
package by innovatively selecting the suitable elements to diligently
represent their actual behavior. Three-dimensional finite element
models were employed to simulate the physically real situation as
close as possible, with the use of an experimentally and numerically
validated finite element model. Comparative results and conclusions
based on the analyses are presented. For similar extents and locations
of debonding, the effect of debonding on natural frequencies appears
greatly dependent on the end conditions of the panel, giving greater
decrease in natural frequency when the panels are more restrained.
Some modes are more sensitive to debonding and this sensitivity
seems to be related to their vibration mode shapes. The fundamental
mode seems generally the least sensitive mode to debonding with
respect to the variation in free vibration characteristics. The results
indicate the effectiveness of the developed three dimensional finite
element models in assessing debonding damage in composite
sandwich panels.
Abstract: In this study, out-of-plane free vibrations of a circular
rods is investigated theoretically. The governing equations for
naturally twisted and curved spatial rods are obtained using
Timoshenko beam theory and rewritten for circular rods. Effects of
the axial and shear deformations are considered in the formulations.
Ordinary differential equations in scalar form are solved analytically
by using transfer matrix method. The circular rods of the mass matrix
are obtained by using straight rod of consistent mass matrix. Free
vibrations frequencies obtained by solving eigenvalue problem. A
computer program coded in MATHEMATICA language is prepared.
Circular beams are analyzed through various examples for free
vibrations analysis. Results are compared with ANSYS results based
on finite element method and available in the literature.
Abstract: The principle of the seismic performance evaluation methods is to provide a measure of capability for a building or set of buildings to be damaged by an earthquake. The common objective of many of these methods is to supply classification criteria. The purpose of this study is to present a method for assessing the seismic performance of structures, based on Pushover method; we are particularly interested in reinforced concrete frame structures, which represent a significant percentage of damaged structures after a seismic event. The work is based on the characterization of seismic movement of the various earthquake zones in terms of PGA and PGD that is obtained by means of SIMQK_GR and PRISM software and the correlation between the points of performance and the scalar characterizing the earthquakes will developed.
Abstract: Steel tubular towers serving as support structures for large wind turbines are subjected to several hundred million stress cycles caused by the turbulent nature of the wind. This causes highcycle fatigue, which could govern the design of the tower. Maintaining the support structure after the wind turbines reach its typical 20-year design life has become a common practice; however, quantifying the changes in the reliability on the tower is not usual. In this paper the effect of fatigue damage in the wind turbine structure is studied whit the use of fracture mechanics, and a method to estimate the reliability over time of the structure is proposed. A representative wind turbine located in Oaxaca, Mexico is then studied. It is found that the system reliability is significantly affected by the accumulation of fatigue damage.
Abstract: A large amount of blast furnace slag is generated in
China. Most ground granulated blast furnace slag (GGBS) however
ends up in low-grade applications. Blast furnace slag, ground to an
appropriate fineness, can be used as a partial replacement of
cementitious material in concrete. The potential for using GGBS in
structural concrete, e.g. concrete beams and columns is investigated
at Xi’an Jiaotong-Liverpool University (XJTLU). With 50% of CEM
I cement replaced with GGBS, peak hydration temperatures
determined in a suspended concrete slab reduced by 20%. This
beneficiary effect has not been further improved with 70% of CEM I
replaced with GGBS. Partial replacement of CEM I with GGBS has a
retardation effect on the early-age strength of concrete. More GGBS
concrete mixes will be conducted to identify an ‘optimum’
replacement level which will lead to a reduced thermal loading,
without significantly compromising the early-age strength of
concrete.
Abstract: In this paper static scheme of under-frequency based load shedding is considered for chemical and petrochemical industries with islanded distribution networks relying heavily on the primary commodity to ensure minimum production loss, plant downtime or critical equipment shutdown. A simplistic methodology is proposed for in-house implementation of this scheme using underfrequency relays and a step by step guide is provided including the techniques to calculate maximum percentage overloads, frequency decay rates, time based frequency response and frequency based time response of the system. Case study of FFL electrical system is utilized, presenting the actual system parameters and employed load shedding settings following the similar series of steps. The arbitrary settings are then verified for worst overload conditions (loss of a generation source in this case) and comprehensive system response is then investigated.