Abstract: Hybrid electric vehicles can reduce pollution and
improve fuel economy. Power-split hybrid electric vehicles (HEVs)
provide two power paths between the internal combustion engine
(ICE) and energy storage system (ESS) through the gears of an
electrically variable transmission (EVT). EVT allows ICE to operate
independently from vehicle speed all the time. Therefore, the ICE can
operate in the efficient region of its characteristic brake specific fuel
consumption (BSFC) map. The two-mode powertrain can operate in
input-split or compound-split EVT modes and in four different fixed
gear configurations. Power-split architecture is advantageous because
it combines conventional series and parallel power paths. This
research focuses on input-split and compound-split modes in the
two-mode power-split powertrain. Fuzzy Logic Control (FLC) for an
internal combustion engine (ICE) and PI control for electric machines
(EMs) are derived for the urban driving cycle simulation. These
control algorithms reduce vehicle fuel consumption and improve ICE
efficiency while maintaining the state of charge (SOC) of the energy
storage system in an efficient range.
Abstract: Complex lifting entry was selected for precise landing
performance during the Mars Science Laboratory entry. This study
aims to develop the three-dimensional numerical method for precise
computation and the surface panel method for rapid engineering
prediction. Detailed flow field analysis for Mars exploration mission
was performed by carrying on a series of fully three-dimensional
Navier-Stokes computations. The static aerodynamic performance was
then discussed, including the surface pressure, lift and drag coefficient,
lift-to-drag ratio with the numerical and engineering method.
Computation results shown that the shock layer is thin because of
lower effective specific heat ratio, and that calculated results from both
methods agree well with each other, and is consistent with the
reference data. Aerodynamic performance analysis shows that CG
location determines trim characteristics and pitch stability, and certain
radially and axially shift of the CG location can alter the capsule lifting
entry performance, which is of vital significance for the aerodynamic
configuration design and inner instrument layout of the Mars entry
capsule.
Abstract: In this paper we propose a computer-aided solution
with Genetic Algorithms in order to reduce the drafting of reports:
FMEA analysis and Control Plan required in the manufacture of the
product launch and improved knowledge development teams for
future projects. The solution allows to the design team to introduce
data entry required to FMEA. The actual analysis is performed using
Genetic Algorithms to find optimum between RPN risk factor and
cost of production. A feature of Genetic Algorithms is that they are
used as a means of finding solutions for multi criteria optimization
problems. In our case, along with three specific FMEA risk factors is
considered and reduce production cost. Analysis tool will generate
final reports for all FMEA processes. The data obtained in FMEA
reports are automatically integrated with other entered parameters in
Control Plan. Implementation of the solution is in the form of an
application running in an intranet on two servers: one containing
analysis and plan generation engine and the other containing the
database where the initial parameters and results are stored. The
results can then be used as starting solutions in the synthesis of other
projects. The solution was applied to welding processes, laser cutting
and bending to manufacture chassis for buses. Advantages of the
solution are efficient elaboration of documents in the current project
by automatically generating reports FMEA and Control Plan using
multiple criteria optimization of production and build a solid
knowledge base for future projects. The solution which we propose is
a cheap alternative to other solutions on the market using Open
Source tools in implementation.
Abstract: Exploration and exploitation capabilities are both
important within Operations as means for improvement when
managed separately, and for establishing dynamic improvement
capabilities when combined in balance. However, it is unclear what
exploration and exploitation capabilities imply in improvement and
development work within an Operations context. So, in order to
better understand how to develop exploration and exploitation
capabilities within Operations, the main characteristics of these
constructs needs to be identified and further understood. Thus, the
objective of this research is to increase the understanding about
exploitation and exploration characteristics, to concretize what they
translates to within the context of improvement and development
work in an Operations unit, and to identify practical challenges. A
literature review and a case study are presented. In the literature
review, different interpretations of exploration and exploitation are
portrayed, key characteristics have been identified, and a deepened
understanding of exploration and exploitation characteristics is
described. The case in the study is an Operations unit, and the aim is
to explore to what extent and in what ways exploration and
exploitation activities are part of the improvement structures and
processes. The contribution includes an identification of key
characteristics of exploitation and exploration, as well as an
interpretation of the constructs. Further, some practical challenges are
identified. For instance, exploration activities tend to be given low
priority, both in daily work as in the manufacturing strategy. Also,
the overall understanding about the concepts of exploitation and
exploration (or any similar aspect of dynamic improvement
capabilities) is very low.
Abstract: The paper develops a Non-Linear Model Predictive
Control (NMPC) of water quality in Drinking Water Distribution
Systems (DWDS) based on the advanced non-linear quality dynamics
model including disinfections by-products (DBPs). A special attention
is paid to the analysis of an impact of the flow trajectories prescribed
by an upper control level of the recently developed two-time scale
architecture of an integrated quality and quantity control in DWDS.
The new quality controller is to operate within this architecture in the
fast time scale as the lower level quality controller. The controller
performance is validated by a comprehensive simulation study based
on an example case study DWDS.
Abstract: In the immunologic sense, clinical infection is a state
of failure of the immune system to combat the pathogenic weapon of
the bacteria invading the host. A motile gram negative vibroid
organism associated with marked mono and poly nuclear cell
responses was traced during the examination of a clinical material
from an infected common carp Cyprinus carpio. On primary plate
culture, growth was shown to be pure, dense population of an
Aeromonas-like colony morphotype. The pure isolate was found to
be; Aerobic, facultatively anaerobic, non-halophilic, grew at 0C, and
37C, oxidase positive utilizes glucose through fermentative pathway,
resist 0/129 and novobiocin, produces alanine and lysine
decarboxylases but non-producing ornithine dehydrolases. Tests for
the in vitro determinants of pathogenicity has shown to be; Betahaemolytic
onto blood agar, gelatinase, casienase and amylase
producer. Three in vivo determinants of pathogenicity were tested as,
the lethal dose fifty, the pathogenesis and pathogenicity. It was
evident that 0.1 milliliter of the causal bacterial cell suspension of a
density 1 x 107 CFU/ml injected intramuscularly into an average of
100gms fish toke five days incubation period, then at the day six
morbidity and mortality were initiated. LD50 was recorded at the day
12 post-infection. Use of an LD50 doses to study the pathogenicity,
reveals mononuclear and polynuclear cell responses, on examining
the stained direct films of the clinical materials from the
experimentally infected fish. Re-isolation tests confirm that the reisolant
is same. The course of the infection in natural case was shown
manifestation of; skin ulceration, haemorrhage and descaling. On
evisceration, the internal organs were shown; congestion in the
intestines, spleen and, air sacs. The induced infection showed a
milder form of these manifestations. The grading of the virulence of
this organism was virulent causing chronic course of infections as
indicated from the pathogenesis and pathogenicity studies. Thus the
infectious bacteria were consistent with Aeromonas hydrophila, and
the infection was chronic.
Abstract: This study was aimed to investigate the machining
stability of a spindle tool with different preloaded amount. To this end,
the vibration tests were conducted on the spindle unit with different
preload to assess the dynamic characteristics and machining stability
of the milling machine. Current results demonstrate that the tool tip
frequency response characteristics and the machining stabilities in X
and Y direction are affected to change due to the different preload of
spindle bearings. As found from the results, a high preloaded spindle
tool shows higher limited cutting depth at mid position, while a spindle
with low preload shows a higher limited depth. This indicates that the
machining stability of a milling machine is affected to vary by the
spindle unit when it was assembled with different bearing preload.
Abstract: More than 3000 plants of notable phyto-therapeutic
value grow in South Africa; these include Cissampelos capensis,
commonly known in Afrikaans as dawidjie or dawidjiewortel. C.
capensis is the most significant and popular medicinal plant used by
the Khoisan as well as other rural groups in the Western region of
South Africa. Its rhizomes are traditionally used to treat male fertility
problems. Yet, no studies have investigated the effects of this plant or
its extracts on human spermatozoa. Therefore, this study aimed at
investigating the effects of C. capensis rhizome extract (CRE)
fractions on ejaculated human spermatozoa in vitro. Spermatozoa
from a total of 77 semen samples were washed with human tubular
fluid medium supplemented with bovine serum albumin (HTF-BSA)
and incubated for 2 hours with 20 μg/ml progesterone (P4) followed
by incubation with different concentrations (0, 0.05, 0.5, 5, 50, 200
μg/ml) of fractionated CRE (F1=0% MeOH, F2=30% MeOH,
F3=60% MeOH and F4=100% MeOH) for 1.5 hours at 37°C. A
sample without addition of CRE fractions served as control. Samples
were analyzed for sperm motility, reactive oxygen species (ROS),
DNA-fragmentation, acrosome reaction and capacitation. Results
showed that F1 resulted in significantly higher values for ROS,
capacitation and hyper-activation compared to F2, F3, and F4 with
P4-stimulated samples generally having higher values. No significant
effect was found for the other parameters. In conclusion, alkaloids
present in F1 of CRE appear to have triggered sperm intrinsic ROS
production leading to sperm capacitation and acrosome reaction
induced by P4.
Abstract: Copper (I) oxide microparticles with the morphology
of cubic and hollow sphere were synthesized with the assistance of
surfactant as the shape controller. Both particles were then subjected
to study the catalytic activity and observed the results of shape effects
of catalysts on rate of catalytic reaction. The decolorizing reaction of
crystal violet and sodium hydroxide was chosen and measured the
decreasing of reactant with respect to times using spectrophotometer.
The result revealed that morphology of crystal had no effect on the
catalytic activity for crystal violet reaction but contributed to total
surface area predominantly.
Abstract: In this study, the pedestrian simulation VISWALK
integration and application platform ant algorithms written program
made to construct a renovation engineering schedule planning mode.
The use of simulation analysis platform construction site when the user
running the simulation, after calculating the user walks in the case of
construction delays, the ant algorithm to find out the minimum delay
time schedule plan, and add volume and unit area deactivated loss of
business computing, and finally to the owners and users of two
different positions cut considerations pick out the best schedule
planning. To assess and validate its effectiveness, this study
constructed the model imported floor of a shopping mall floor
renovation engineering cases. Verify that the case can be found from
the mode of the proposed project schedule planning program can
effectively reduce the delay time and the user's walking mall loss of
business, the impact of the operation on the renovation engineering
facilities in the building to a minimum.
Abstract: An investigation of adaptable winglets for enhancing
morphing aircraft performance is described in this paper. The
concepts investigated consist of various winglet configurations
fundamentally centered on a baseline swept wing. The impetus for
the work was to identify and optimize winglets to enhance the
aerodynamic efficiency of a morphing aircraft. All computations
were performed with Athena Vortex Lattice modelling with varying
degrees of twist and cant angle considered. The results from this
work indicate that if adaptable winglets were employed on aircraft’s
improvements in aircraft performance could be achieved.
Abstract: Aluminium matrix composites with alumina
reinforcements give superior mechanical & physical properties. Their
applications in several fields like automobile, aerospace, defense,
sports, electronics, bio-medical and other industrial purposes are
becoming essential for the last several decades. In the present work,
fabrication of hybrid composite was done by Stir casting technique
using Al 6061 as a matrix with alumina and silicon carbide (SiC) as
reinforcement materials. The weight percentage of alumina is varied
from 2 to 4% and the silicon carbide weight percentage is maintained
constant at 2%. Hardness and wear tests are performed in the as cast
and heat treated conditions. Age hardening treatment was performed
on the specimen with solutionizing at 550°C, aging at two
temperatures (150 and 200°C) for different time durations. Hardness
distribution curves are drawn and peak hardness values are recorded.
Hardness increase was very sensitive with respect to the decrease in
aging temperature. There was an improvement in wear resistance of
the peak aged material when aged at lower temperature. Also
increase in weight percent of alumina, increases wear resistance at
lower temperature but opposite behavior was seen when aged at
higher temperature.
Abstract: This paper addresses a cutting edge method of
business demand forecasting, based on an empirical probability
function when the historical behavior of the data is random.
Additionally, it presents error determination based on the numerical
method technique ‘propagation of errors.’ The methodology was
conducted characterization and process diagnostics demand planning
as part of the production management, then new ways to predict its
value through techniques of probability and to calculate their mistake
investigated, it was tools used numerical methods. All this based on
the behavior of the data. This analysis was determined considering
the specific business circumstances of a company in the sector of
communications, located in the city of Bogota, Colombia. In
conclusion, using this application it was possible to obtain the
adequate stock of the products required by the company to provide its
services, helping the company reduce its service time, increase the
client satisfaction rate, reduce stock which has not been in rotation
for a long time, code its inventory, and plan reorder points for the
replenishment of stock.
Abstract: When neck pain is associated with pain, numbness, or
weakness in the arm, shoulder, or hand, further investigation is
needed as these are symptoms indicating pressure on one or more
nerve roots. Evaluation necessitates a neurologic examination and
imaging using an MRI/CT scan. A degenerating disc loses some
thickness and is less flexible, causing inter-vertebrae space to narrow.
A radiologist diagnoses an Intervertebral Disc Degeneration (IDD) by
localizing every inter-vertebral disc and identifying the pathology in
a disc based on its geometry and appearance. Accurate localizing is
necessary to diagnose IDD pathology. But, the underlying image
signal is ambiguous: a disc’s intensity overlaps the spinal nerve
fibres. Even the structure changes from case to case, with possible
spinal column bending (scoliosis). The inter-vertebral disc
pathology’s quantitative assessment needs accurate localization of the
cervical region discs. In this work, the efficacy of multilevel set
segmentation model, to segment cervical discs is investigated. The
segmented images are annotated using a simple distance matrix.
Abstract: The Economic Lot Scheduling Problem (ELSP) is a
valuable mathematical model that can support decision-makers to
make scheduling decisions. The basic period approach is effective for
solving the ELSP. The assumption for applying the basic period
approach is that a product must use its maximum production rate to be
produced. However, a product can lower its production rate to reduce
the average total cost when a facility has extra idle time. The past
researches discussed how a product adjusts its production rate under
the common cycle approach. To the best of our knowledge, no studies
have addressed how a product lowers its production rate under the
basic period approach. This research is the first paper to discuss this
topic. The research develops a simple fixed rate approach that adjusts
the production rate of a product under the basic period approach to
solve the ELSP. Our numerical example shows our approach can find a
better solution than the traditional basic period approach. Our
mathematical model that applies the fixed rate approach under the
basic period approach can serve as a reference for other related
researches.
Abstract: Nowadays, the main goal for modern horticultural
production is an increase the quality. In recent years, the use of
organic fertilizers or biostimulants that can be applied in agriculture
to improve quali-quantitative crop yields has encountered increasing
interest. Biostimulants are gaining importance also for their possible
use in organic and sustainable agriculture, to avoid excessive
fertilizer applications. Consecutive experimental trials were carried
out in the Apulia region (southern Italy) on three herbaceous crops
(cauliflower, pepper, fennel) grown in pots under conventional and
organic fertilization systems without and with biostimulants. The aim
was to determine the effects of three biostimulants (Siapton®10L,
Micotech L, Lysodin Alga-Fert) on quali-quantitative yield
characteristics. At harvest, the quali-quantitative yield characteristics
of each crop were determined. All of the experimental data were
subjected to analysis of variance (ANOVA), and when significant
effects were detected, the means were compared using Tukey’s tests.
These data show large differences in these yield characteristics
between conventional and organic crops, particularly highlighting
higher yields for the conventional crops, while variable results were
generally observed when the biostimulants were applied. In this
context, there were no effects of the biostimulants on the quantitative
yield, whereas there were low positive effects on the qualitative
characteristics, as related to higher dry matter content of cauliflower,
and higher soluble solids content of pepper. Moreover, there were
evident positive effects of the biostimulants with fennel, due to the
lower nitrate content. These latter data are in line with most of the
published literature obtained for other herbaceous crops.
Abstract: The nanoindentation behaviour and phase
transformation of annealed single-crystal silicon wafers are examined.
The silicon specimens are annealed at temperatures of 250, 350 and
450ºC, respectively, for 15 minutes and are then indented to maximum
loads of 30, 50 and 70 mN. The phase changes induced in the indented
specimens are observed using transmission electron microscopy
(TEM) and micro-Raman scattering spectroscopy (RSS). For all
annealing temperatures, an elbow feature is observed in the unloading
curve following indentation to a maximum load of 30 mN. Under
higher loads of 50 mN and 70 mN, respectively, the elbow feature is
replaced by a pop-out event. The elbow feature reveals a complete
amorphous phase transformation within the indented zone, whereas
the pop-out event indicates the formation of Si XII and Si III phases.
The experimental results show that the formation of these crystalline
silicon phases increases with an increasing annealing temperature and
indentation load. The hardness and Young’s modulus both decrease as
the annealing temperature and indentation load are increased.
Abstract: The system for analyzing and eliciting public
grievances serves its main purpose to receive and process all sorts of
complaints from the public and respond to users. Due to the more
number of complaint data becomes big data which is difficult to store
and process. The proposed system uses HDFS to store the big data
and uses MapReduce to process the big data. The concept of cache
was applied in the system to provide immediate response and timely
action using big data analytics. Cache enabled big data increases the
response time of the system. The unstructured data provided by the
users are efficiently handled through map reduce algorithm. The
processing of complaints takes place in the order of the hierarchy of
the authority. The drawbacks of the traditional database system used
in the existing system are set forth by our system by using Cache
enabled Hadoop Distributed File System. MapReduce framework
codes have the possible to leak the sensitive data through
computation process. We propose a system that add noise to the
output of the reduce phase to avoid signaling the presence of
sensitive data. If the complaints are not processed in the ample time,
then automatically it is forwarded to the higher authority. Hence it
ensures assurance in processing. A copy of the filed complaint is sent
as a digitally signed PDF document to the user mail id which serves
as a proof. The system report serves to be an essential data while
making important decisions based on legislation.
Abstract: Because blueberries are worldwide recognized as a
good source of beneficial components, their consumption has
increased in the past decades, and so have the scientific works about
their properties. Hence, this work was undertaken to evaluate the
effect of some production and conservation factors on the properties
of blueberries from cultivar Bluecrop. The physical and chemical
analyses were done according to established methodologies and then
all data was treated using software SPSS for assessment of the
possible differences among the factors investigated and/or the
correlations between the variables at study. The results showed that
location of production influenced some of the berries properties
(caliber, sugars, antioxidant activity, color and texture) and that the
age of the bushes was correlated with moisture, sugars and acidity, as
well as lightness. On the other hand, altitude of the farm only was
correlated to sugar content. With regards to conservation, it
influenced only anthocyanins content and DPPH antioxidant activity.
Finally, the type of extract and the order of extraction had a
pronounced influence on all the phenolic properties evaluated.
Abstract: In the past decade, the use of digital image correlation
(DIC) techniques has increased significantly in the area of
experimental mechanics, especially for materials behavior
characterization. This non-contact tool enables full field displacement
and strain measurements over a complete region of interest. The DIC
algorithm requires a random contrast pattern on the surface of the
specimen in order to perform properly. To create this pattern, the
specimen is usually first coated using a white matt paint. Next, a
black random speckle pattern is applied using any suitable method. If
the applied paint coating is too thick, its top surface may not be able
to exactly follow the deformation of the specimen, and consequently,
the strain measurement might be underestimated. In the present
article, a study of the influence of the paint thickness on the strain
underestimation is performed for different strain levels. The results
are then compared to typical paint coating thicknesses applied by
experienced DIC users. A slight strain underestimation was observed
for paint coatings thicker than about 30μm. On the other hand, this
value was found to be uncommonly high compared to coating
thicknesses applied by DIC users.