Abstract: Effect of biopesticide from wood vinegar and
extracted substances from 3 medicinal plants such as: non taai yak
(Stemona tuberosa Lour), boraphet (Tinospora crispa Mier) and
derris (Derris elliptica Roxb) were tested on the age five years of
pomelo. The selected pomelo was carried out for insects’ pest control
and its quality. The experimental site was located at farmer’s orchard
in Phichit Province, Thailand. This study was undertaken during the
drought season (December to March). The extracted from plants and
wood vinegar were evaluated in 6 treatments: 1) water as control; 2)
wood vinegar; 3) S. tuberosa Lour; 4) T. crispa Mier; 5) D. elliptica
Roxb; 6) mixed (wood vinegar + S. tuberosa Lour + T. crispa Mier +
D. elliptica Roxb). The experiment was RCB with 6 treatments and 3
replications per treatment. The results showed that T. crispa Mier was
the highest effectiveness for reduction population of thrips
(Scirtothrips dorsalis Hood) and citrus leaf miner (Phyllocnistis
citrella Stainton) at 14.10 and 15.37 respectively, followed by
treatment of mixed, D. elliptica Roxb, S. tuberosa Lour and wood
vinegar with significance different. Additionally, T. crispa Mier
promoted the high quality of harvested pomelo in term of thickness
of skin at 12.45 mm and S. tuberosa Lour gave the high quality of the
pomelo in term of firmness (276.5 kg/cm2) and brix (11.0%).
Abstract: This research was conducted in the Mae Sot
Watershed where located in the Moei River Basin at the Upper
Salween River Basin in Tak Province, Thailand. The Mae Sot
Municipality is the largest urban area in Tak Province and situated in
the midstream of the Mae Sot Watershed. It usually faces flash flood
problem after heavy rain due to poor flood management has been
reported since economic rapidly bloom up in recent years. Its
catchment can be classified as ungauged basin with lack of rainfall
data and no any stream gaging station was reported. It was attached
by most severely flood events in 2013 as the worst studied case for
all those communities in this municipality. Moreover, other problems
are also faced in this watershed, such shortage water supply for
domestic consumption and agriculture utilizations including a
deterioration of water quality and landslide as well. The research
aimed to increase capability building and strengthening the
participation of those local community leaders and related agencies to
conduct better water management in urban area was started by mean
of the data collection and illustration of the appropriated application
of some short period rainfall forecasting model as they aim for better
flood relief plan and management through the hydrologic model
system and river analysis system programs. The authors intended to
apply the global rainfall data via the integrated data viewer (IDV)
program from the Unidata with the aim for rainfall forecasting in a
short period of 7-10 days in advance during rainy season instead of
real time record. The IDV product can be present in an advance
period of rainfall with time step of 3-6 hours was introduced to the
communities. The result can be used as input data to the hydrologic
modeling system model (HEC-HMS) for synthesizing flood
hydrographs and use for flood forecasting as well. The authors
applied the river analysis system model (HEC-RAS) to present flood
flow behaviors in the reach of the Mae Sot stream via the downtown
of the Mae Sot City as flood extents as the water surface level at
every cross-sectional profiles of the stream. Both models of HMS and
RAS were tested in 2013 with observed rainfall and inflow-outflow
data from the Mae Sot Dam. The result of HMS showed fit to the
observed data at the dam and applied at upstream boundary discharge
to RAS in order to simulate flood extents and tested in the field, and
the result found satisfying. The product of rainfall from IDV was fair
while compared with observed data. However, it is an appropriate
tool to use in the ungauged catchment to use with flood hydrograph
and river analysis models for future efficient flood relief plan and
management.
Abstract: This article discusses issues related to the System of
Innovation: Comparing economies of Brazil and South Africa.
Having as this study aimed at comparing the Innovation System of
the countries mentioned. Then briefly describe the process of Venture
Capital and present the industry innovation in Brazil and South
Africa. The methodological approach described in this article is
descriptive and the approach is qualitative, taking as a basis
secondary data relating to research articles. The main results are
related to the different forms of financing of Venture Capital used by
countries compared, in addition to the training and economic policy.
And finally, it was highlighted the importance of implementation of
policy reforms for the Brazil and Africa in the innovation process.
Abstract: Remote sensing plays a vital role in mapping of
resources and monitoring of environments of the earth. In the present
research study, mapping and monitoring of clay siltations occurred in
the Alkhod Dam of Muscat, Sultanate of Oman are carried out using
low-cost multispectral Landsat and ASTER data. The dam is
constructed across the Wadi Samail catchment for ground water
recharge. The occurrence and spatial distribution of siltations in the
dam are studied with five years of interval from the year 1987 of
construction to 2014. The deposits are mainly due to the clay, sand
and silt occurrences derived from the weathering rocks of ophiolite
sequences occurred in the Wadi Samail catchment. The occurrences
of clays are confirmed by minerals identification using ASTER
VNIR-SWIR spectral bands and Spectral Angle Mapper supervised
image processing method. The presence of clays and their spatial
distribution are verified in the field. The study recommends the
technique and the low-cost satellite data to similar region of the
world.
Abstract: The effects of basil and/or chamomile seed
supplementation on the growth of Hubbard broiler chicks were
evaluated. The antioxidant effects of these supplements were also
assessed. 120 1-day-old broiler chicks were randomly divided into
four equal groups. The control group (group 1) was fed a basal diet
(BD) without supplementation. Groups 2, 3, and 4 were fed the BD
supplemented with 10g basil, 10g chamomile, and 5g basil plus 5g
chamomile per kg of food, respectively. Basil supplementation alone
or in combination with chamomile non-significantly (P≥0.05)
increased final body weight (3.2% and 0.3%, respectively) and
weight gain (3.5% and 3.6%, respectively) over the experimental
period. Chamomile supplementation alone non-significantly (P≥0.05)
reduced final body weight and weight gain over the experimental
period by 1.7% and 1.7%, respectively. In comparison to the control
group, herbal seed supplementation reduced feed intake and
improved the feed conversion and protein efficiency ratios. In
general, basil seed supplementation stimulated chicken growth and
improved the feed efficiency more effectively than chamomile seed
supplementation. The antioxidant activities of basil and/or chamomile
supplementation were examined in the thymus, bursa, and spleen. In
chickens that received supplements, the level of malondialdehyde
was significantly decreased, whereas the activities of glutathione,
superoxide dismutase, and catalase were significantly increased
(P
Abstract: This paper presents two types of microstrip bandpass
filter (BPF) at microwave frequencies. The first one is a tunable BPF
using planar patch resonators based on a varactor diode. The filter is
formed by a triple mode circular patch resonator with two pairs of
slots, in which the varactor diodes are connected. Indeed, this filter is
initially centered at 2.4 GHz; the center frequency of the tunable
patch filter could be tuned up to 1.8 GHz simultaneously with the
bandwidth, reaching high tuning ranges. Lossless simulations were
compared to those considering the substrate dielectric, conductor
losses and the equivalent electrical circuit model of the tuning
element in order to assess their effects. Within these variations,
simulation results showed insertion loss better than 2 dB and return
loss better than 10 dB over the passband. The second structure is a
BPF for ultra-wideband (UWB) applications based on multiple-mode
resonator (MMR) and rectangular-shaped defected ground structure
(DGS). This filter, which is compact size of 25.2 x 3.8 mm2, provides
in the pass band an insertion loss of 0.57 dB and a return loss greater
than 12 dB. The proposed filters presents good performances and the
simulation results are in satisfactory agreement with the
experimentation ones reported elsewhere.
Abstract: For centuries humans have used the antimicrobial
properties of copper to their advantage. Yet, after all these years the
underlying mechanisms of copper mediated cell death in various
microbes remain unclear. We had explored the hypothesis that copper
mediated increased levels of lipid peroxidation in the membrane fatty
acids is responsible for increased killing in Escherichia coli. In this
study we show that in both gram positive (Staphylococcus aureus)
and gram negative (Pseudomonas aeruginosa) bacteria there is a
strong correlation between copper mediated cell death and increased
levels of lipid peroxidation. Interestingly, the non-spore forming
gram positive bacteria as well as gram negative bacteria show similar
patterns of cell death, increased levels of lipid peroxidation, as well
as genomic DNA degradation, however there is some difference in
loss in membrane integrity upon exposure to copper alloy surface.
Abstract: Many aluminum motorcycle parts produced by a high
pressure die casting. Some parts such as fuel caps were a thin and
complex shape. This part risked for porosities and blisters on surface
if it only depended on an experience of mold makers for mold design.
This research attempted to use CAST-DESIGNER software
simulated the high pressure die casting process with the same process
parameters of a motorcycle fuel cap production. The simulated results
were compared with fuel cap products and expressed the same
porosity and blister locations on cap surface. An average of absolute
difference of simulated results was obtained 0.094 mm when
compared the simulated porosity and blister defect sizes on the fuel
cap surfaces with the experimental micro photography. This
comparison confirmed an accuracy of software and will use the
setting parameters to improve fuel cap molds in the further work.
Abstract: Composite material based on Fe3Si micro-particles
and Mn-Zn nano-ferrite was prepared using powder metallurgy
technology. The sol-gel followed by autocombustion process was
used for synthesis of Mn0.8Zn0.2Fe2O4 ferrite. 3 wt.% of mechanically
milled ferrite was mixed with Fe3Si powder alloy. Mixed micro-nano
powder system was homogenized by the Resonant Acoustic Mixing
using ResodynLabRAM Mixer. This non-invasive homogenization
technique was used to preserve spherical morphology of Fe3Si
powder particles. Uniaxial cold pressing in the closed die at pressure
600 MPa was applied to obtain a compact sample. Microwave
sintering of green compact was realized at 800°C, 20 minutes, in air.
Density of the powders and composite was measured by
Hepycnometry. Impulse excitation method was used to measure
elastic properties of sintered composite. Mechanical properties were
evaluated by measurement of transverse rupture strength (TRS) and
Vickers hardness (HV). Resistivity was measured by 4 point probe
method. Ferrite phase distribution in volume of the composite was
documented by metallographic analysis.
It has been found that nano-ferrite particle distributed among
micro- particles of Fe3Si powder alloy led to high relative density
(~93%) and suitable mechanical properties (TRS >100 MPa, HV
~1GPa, E-modulus ~140 GPa) of the composite. High electric
resistivity (R~6.7 ohm.cm) of prepared composite indicate their
potential application as soft magnetic material at medium and high
frequencies.
Abstract: Since, it is essential to provide homeless people by the
earthquake with safe, habitable accommodation repairing medium
and slight levels of damage at the connection parts should be
undertaken. In order to prove that a repaired connection was
sufficiently strong, a precast beam to column post tensioned
connection was tested in three phases. In phase one, the middle level
damage was observed at 6% drift at these connections. As a result of
the extra loads applied, little damage was observed. In the last phase,
the four connections tested in the first phase were repaired using
epoxy resin and then retested. The results from the tests on the
repaired precast and the undamaged specimens showed that the
repaired specimens were sufficiently strong, thus proving that repair
to damaged precast beam to column post tensioned connections can
be undertaken.
Abstract: The aim of this study was to select the best strains of
Saccharomyces cerevisiae able to resist lead and cadmium. Ten
strains were screened on the basis of their resistance at different
concentrations of 0, 2, 4, 8, 12, 16, 20 and 24 ppm for Pb and 0, 0.5,
1, 2, 4, 6, 8 and 10 ppm for Cd. The properties of baker's yeast
quality were decreased by the increase of Pb or Cd in growth
medium. The slope values of yield, total viable cells and gassing
power of produced baker's yeast were investigated as an indicator of
metal resistant. In addition, concentrations of Pb and Cd in produced
baker's yeast were determined. The strain of S. cerevisiae FH-620
had the highest resistance against Pb and Cd and had the minimum
levels of both two investigated metals in produced baker's yeast.
Abstract: In this paper, we propose an automatic verification
technology of software patches for user virtual environments on IaaS
Cloud to decrease verification costs of patches. In these days, IaaS
services have been spread and many users can customize virtual
machines on IaaS Cloud like their own private servers. Regarding to
software patches of OS or middleware installed on virtual machines,
users need to adopt and verify these patches by themselves. This task
increases operation costs of users. Our proposed method replicates
user virtual environments, extracts verification test cases for user
virtual environments from test case DB, distributes patches to virtual
machines on replicated environments and conducts those test cases
automatically on replicated environments. We have implemented the
proposed method on OpenStack using Jenkins and confirmed the
feasibility. Using the implementation, we confirmed the effectiveness
of test case creation efforts by our proposed idea of 2-tier abstraction
of software functions and test cases. We also evaluated the automatic
verification performance of environment replications, test cases
extractions and test cases conductions.
Abstract: Newly synthesized Polypropylene-g-Polyethylene
glycol polymer was first time used for a compartment-less enzymatic
fuel cell. Working electrodes based on Polypropylene-g-Polyethylene
glycol were operated as unmediated and mediated system (with
ferrocene and gold/cobalt oxide nanoparticles). Glucose oxidase and
bilirubin oxidase was selected as anodic and cathodic enzyme,
respectively. Glucose was used as fuel in a single-compartment and
membrane-less cell. Maximum power density was obtained as 0.65
nW cm-2, 65 nW cm-2 and 23500 nW cm-2 from the unmediated,
ferrocene and gold/cobalt oxide modified polymeric film,
respectively. Power density was calculated to be ~16000 nW cm-2 for
undiluted wastewater sample with gold/cobalt oxide nanoparticles
including system.
Abstract: The development of the United Arab Emirates (UAE)
into a regional trade, tourism, finance and logistics hub has
transformed its real estate markets. However, speculative activity and
price volatility remain concerns. UAE residential market values
(MV) are exposed to fluctuations in capital flows and migration
which, in turn, are affected by geopolitical uncertainty, oil price
volatility and global investment market sentiment. Internally, a
complex interplay between administrative boundaries, land tenure,
building quality and evolving location characteristics fragments UAE
residential property markets. In short, the UAE Residential Valuation
System (UAE-RVS) confronts multiple challenges to collect, filter
and analyze relevant information in complex and dynamic spatial and
capital markets. A robust (RVS) can mitigate the risk of unhelpful
volatility, speculative excess or investment mistakes. The research
outlines the institutional, ontological, dynamic and epistemological
issues at play. We highlight the importance of system capabilities,
valuation standard salience and stakeholders trust.
Abstract: The development of Drugs Delivery System (DDS)
has been widely investigated in the last decades. In this paper, first a
general overview of traditional and modern wound dressing is
presented. This is followed by a review of what scientists have done
in the medical environment, focusing on the possibility to develop a
new alternative for DDS through transdermal pathway, aiming to
treat melanoma skin cancer.
Abstract: A numerical study of natural convection heat transfer
in water filled cavity has been examined in 3-Dfor single phase liquid
cooling system by using an array of parallel plate fins mounted to one
wall of a cavity. The heat generated by a heat source represents a
computer CPU with dimensions of 37.5∗37.5mm mounted on
substrate. A cold plate is used as a heat sink installed on the opposite
vertical end of the enclosure. The air flow inside the computer case is
created by an exhaust fan. A turbulent air flow is assumed and k-ε
model is applied. The fins are installed on the substrate to enhance
the heat transfer. The applied power energy range used is between 15
- 40W. In order to determine the thermal behaviour of the cooling
system, the effect of the heat input and the number of the parallel
plate fins are investigated. The results illustrate that as the fin number
increases the maximum heat source temperature decreases. However,
when the fin number increases to critical value the temperature start
to increase due to the fins are too closely spaced and that cause the
obstruction of water flow. The introduction of parallel plate fins
reduces the maximum heat source temperature by 10% compared to
the case without fins. The cooling system maintains the maximum
chip temperature at 64.68°C when the heat input was at 40W that is
much lower than the recommended computer chips limit temperature
of no more than 85°C and hence the performance of the CPU is
enhanced.
Abstract: With increasingly more mobile health applications
appearing due to the popularity of smartphones, the possibility arises
that these data can be used to improve the medical diagnostic process,
as well as the overall quality of healthcare, while at the same time
lowering costs. However, as of yet there have been no reports of a
successful combination of patient-generated data from smartphones
with data from clinical routine. In this paper we describe how these
two types of data can be combined in a secure way without
modification to hospital information systems, and how they can
together be used in a medical expert system for automatic nutritional
classification and triage.
Abstract: A large amount of data is typically stored in relational
databases (DB). The latter can efficiently handle user queries which
intend to elicit the appropriate information from data sources.
However, direct access and use of this data requires the end users to
have an adequate technical background, while they should also cope
with the internal data structure and values presented. Consequently
the information retrieval is a quite difficult process even for IT or DB
experts, taking into account the limited contributions of relational
databases from the conceptual point of view. Ontologies enable users
to formally describe a domain of knowledge in terms of concepts and
relations among them and hence they can be used for unambiguously
specifying the information captured by the relational database.
However, accessing information residing in a database using
ontologies is feasible, provided that the users are keen on using
semantic web technologies. For enabling users form different
disciplines to retrieve the appropriate data, the design of a Graphical
User Interface is necessary. In this work, we will present an
interactive, ontology-based, semantically enable web tool that can be
used for information retrieval purposes. The tool is totally based on
the ontological representation of underlying database schema while it
provides a user friendly environment through which the users can
graphically form and execute their queries.
Abstract: In order to study the aerodynamic performance of a
semi-flexible membrane wing, Fluid-Structure Interaction simulations
have been performed. The fluid problem has been modeled using
two different approaches which are the vortex panel method and the
numerical solution of the Navier-Stokes equations. Nonlinear analysis
of the structural problem is performed using the Finite Element
Method. Comparison between the two fluid solvers has been made.
Aerodynamic performance of the wing is discussed regarding its
lift and drag coefficients and they are compared with those of the
equivalent rigid wing.
Abstract: Agriculture is the backbone of economy of Pakistan
and cotton is the major agricultural export and supreme source of raw
fiber for our textile industry. To combat severe problems of insect
and weed, combination of three genes namely Cry1Ac, Cry2A and
EPSPS genes was transferred in locally cultivated cotton variety
MNH-786 with the use of Agrobacterium mediated genetic
transformation. The present study focused on the molecular screening
of transgenic cotton plants at T3 generation in order to confirm
integration and expression of all three genes (Cry1Ac, Cry2A and
EPSP synthase) into the cotton genome. Initially, glyphosate spray
assay was used for screening of transgenic cotton plants containing
EPSP synthase gene at T3 generation. Transgenic cotton plants which
were healthy and showed no damage on leaves were selected after 07
days of spray. For molecular analysis of transgenic cotton plants in
the laboratory, the genomic DNA of these transgenic cotton plants
were isolated and subjected to amplification of the three genes. Thus,
seventeen out of twenty (Cry1Ac gene), ten out of twenty (Cry2A
gene) and all twenty (EPSP synthase gene) were produced positive
amplification. On the base of PCR amplification, ten transgenic plant
samples were subjected to protein expression analysis through
ELISA. The results showed that eight out of ten plants were actively
expressing the three transgenes. Real-time PCR was also done to
quantify the mRNA expression levels of Cry1Ac and EPSP synthase
gene. Finally, eight plants were confirmed for the presence and active
expression of all three genes at T3 generation.