Abstract: Nine Degrees of Freedom (9 DOF) systems are
already in development in many areas. In this paper, an integrated
pressure sensor is proposed that will make use of an already existing
monolithic 9 DOF inertial MEMS platform. Capacitive pressure
sensors can suffer from limited sensitivity for a given size of
membrane. This novel pressure sensor design increases the sensitivity
by over 5 times compared to a traditional array of square diaphragms
while still fitting within a 2 mm x 2 mm chip and maintaining a fixed
static capacitance. The improved design uses one large diaphragm
supported by pillars with fixed electrodes placed above the areas of
maximum deflection. The design optimization increases the
sensitivity from 0.22 fF/kPa to 1.16 fF/kPa. Temperature sensitivity
was also examined through simulation.
Abstract: The purpose of this project is to propose a quick and
environmentally friendly alternative to measure the quality of oils
used in food industry. There is evidence that repeated and
indiscriminate use of oils in food processing cause physicochemical
changes with formation of potentially toxic compounds that can
affect the health of consumers and cause organoleptic changes. In
order to assess the quality of oils, non-destructive optical techniques
such as Interferometry offer a rapid alternative to the use of reagents,
using only the interaction of light on the oil. Through this project, we
used interferograms of samples of oil placed under different heating
conditions to establish the changes in their quality. These
interferograms were obtained by means of a Mach-Zehnder
Interferometer using a beam of light from a HeNe laser of 10mW at
632.8nm. Each interferogram was captured, analyzed and measured
full width at half-maximum (FWHM) using the software from
Amcap and ImageJ. The total of FWHMs was organized in three
groups. It was observed that the average obtained from each of the
FWHMs of group A shows a behavior that is almost linear, therefore
it is probable that the exposure time is not relevant when the oil is
kept under constant temperature. Group B exhibits a slight
exponential model when temperature raises between 373 K and 393
K. Results of the t-Student show a probability of 95% (0.05) of the
existence of variation in the molecular composition of both samples.
Furthermore, we found a correlation between the Iodine Indexes
(Physicochemical Analysis) and the Interferograms (Optical
Analysis) of group C. Based on these results, this project highlights
the importance of the quality of the oils used in food industry and
shows how Interferometry can be a useful tool for this purpose.
Abstract: HR is a department that enhances the power of
employee performance in regard with their services, and to make the
organization strategic objectives. The main concern of HR
department is to organize people, focus on policies and their system.
The empirical study shows the relationship between HRM (Human
Resource Management practices) and their Job Satisfaction. The
Hypothesis is testing on a sample of overall 320 employees of 5
different Pharmaceutical departments of different organizations in
Pakistan. The important thing as Relationship of Job satisfaction with
HR Practices, Impact on Job Satisfaction with HR Practices,
Participation of Staff of Different Departments, HR Practices effects
the Job satisfaction, Recruitment or Hiring and Selection effects the
Job satisfaction, Training and Development, Performance and
Appraisals, Compensation affects the Job satisfaction , and Industrial
Relationships affects the Job satisfaction. After finishing all data
analysis, the conclusion is that lots of Job related activities raise the
confidence of Job satisfaction of employees with their salary and
other benefits.
Abstract: Currently, green rating systems are mainly utilized for
correctly sizing mechanical and electrical systems, which have short
lifetime expectancies. In these systems, passive solar and bio-climatic
architecture, which have long lifetime expectancies, are neglected.
Urban rating systems consider buildings and services in addition to
neighborhoods and public transportation as integral parts of the built
environment. The main goal of this study was to develop a more
consistent point allocation system for urban building standards by
using six different lifetime shearing layers: Site, Structure, Skin,
Services, Space, and Stuff, each reflecting distinct environmental
damages. This shearing-layer concept was applied to internationally
well-known rating systems: Leadership in Energy and Environmental
Design (LEED) for Neighborhood Development, BRE
Environmental Assessment Method (BREEAM) for Communities
and Comprehensive Assessment System for Building Environmental
Efficiency (CASBEE) for Urban Development. The results showed
that LEED for Neighborhood Development and BREEAM for
Communities focused on long-lifetime-expectancy building designs,
whereas CASBEE for Urban Development gave equal importance to
the Building and Service Layers. Moreover, although this rating
system was applied using a building-scale assessment, “Urban Area +
Buildings” focuses on a short-lifetime-expectancy system design,
neglecting to improve the architectural design by considering bioclimatic
and passive solar aspects.
Abstract: The development of electric vehicle batteries have
resulted in very high energy density lithium-ion batteries. However,
this progress is accompanied by the risk of thermal runaway, which
can result in serious accidents. Heat pipes are heat exchangers that
are suitable to be applied in electric vehicle battery thermal
management for their lightweight, compact size and do not require
external power supply. This paper aims to examine experimentally a
Flat Plate Loop Heat Pipe (FPLHP) performance as a heat exchanger
in thermal management system of lithium-ion battery for electric
vehicle application. The heat generation of the battery was simulated
using a cartridge heater. Stainless steel screen mesh was used as the
capillary wick. Distilled water, alcohol and acetone were used as
working fluids with a filling ratio of 60%. It was found that acetone
gives the best performance that produces thermal resistance of 0.22
W/°C with 50°C evaporator temperature at heat flux load of 1.61
W/cm2.
Abstract: Voting algorithms are extensively used to make
decisions in fault tolerant systems where each redundant module
gives inconsistent outputs. Popular voting algorithms include
majority voting, weighted voting, and inexact majority voters. Each
of these techniques suffers from scenarios where agreements do not
exist for the given voter inputs. This has been successfully overcome
in literature using fuzzy theory. Our previous work concentrated on a
neuro-fuzzy algorithm where training using the neuro system
substantially improved the prediction result of the voting system.
Weight training of Neural Network is sub-optimal. This study
proposes to optimize the weights of the Neural Network using
Artificial Bee Colony algorithm. Experimental results show the
proposed system improves the decision making of the voting
algorithms.
Abstract: Phonocardiography is important in appraisal of
congenital heart disease and pulmonary hypertension as it reflects the
duration of right ventricular systoles. The systolic murmur in patients
with intra-cardiac shunt decreases as pulmonary hypertension
develops and may eventually disappear completely as the pulmonary
pressure reaches systemic level. Phonocardiography and auscultation
are non-invasive, low-cost, and accurate methods to assess heart
disease. In this work an objective signal processing tool to extract
information from phonocardiography signal using Wavelet is
proposed to classify the murmur as normal or abnormal. Since the
feature vector is large, a Binary Particle Swarm Optimization (PSO)
with mutation for feature selection is proposed. The extracted
features improve the classification accuracy and were tested across
various classifiers including Naïve Bayes, kNN, C4.5, and SVM.
Abstract: To tackle the air pollution issues, Plug-in Hybrid
Electric Vehicles (PHEVs) are proposed as an appropriate solution.
Charging a large amount of PHEV batteries, if not controlled, would
have negative impacts on the distribution system. The control process
of charging of these vehicles can be centralized in parking lots that
may provide a chance for better coordination than the individual
charging in houses. In this paper, an optimization-based approach is
proposed to determine the optimum PHEV parking capacities in
candidate nodes of the distribution system. In so doing, a profile for
charging and discharging of PHEVs is developed in order to flatten
the network load profile. Then, this profile is used in solving an
optimization problem to minimize the distribution system losses. The
outputs of the proposed method are the proper place for PHEV
parking lots and optimum capacity for each parking. The application
of the proposed method on the IEEE-34 node test feeder verifies the
effectiveness of the method.
Abstract: An experimental investigation is carried out to
establish the performance characteristics of a compression ignition
engine while using cerium oxide nanoparticles as additive in neat
diesel and diesel-biodiesel blends. In the first phase of the
experiments, stability of neat diesel and diesel-biodiesel fuel blends
with the addition of cerium oxide nanoparticles is analyzed. After
series of experiments, it is found that the blends subjected to high
speed blending followed by ultrasonic bath stabilization improves the
stability. In the second phase, performance characteristics are studied
using the stable fuel blends in a single cylinder four stroke engine
coupled with an electrical dynamometer and a data acquisition
system. The cerium oxide acts as an oxygen donating catalyst and
provides oxygen for combustion. The activation energy of cerium
oxide acts to burn off carbon deposits within the engine cylinder at
the wall temperature and prevents the deposition of non-polar
compounds on the cylinder wall results reduction in HC emissions.
The tests revealed that cerium oxide nanoparticles can be used as
additive in diesel and diesel-biodiesel blends to improve complete
combustion of the fuel significantly.
Abstract: Experiential marketing is one of the marketing
approaches that offer an exceptional framework to integrate elements
of experience and entertainment in a product or service. Experiential
marketing is defined as a memorable experience that goes deeply into
the customer’s mind. Besides that, customer satisfaction is defined as
an emotional response to the experiences provided by and associated
with particular products or services purchased. Thus, experiential
marketing activities can affect the level of customer satisfaction and
loyalty. In this context, the research aims to explore the relationship
among experiential marketing, customer satisfaction and customer
loyalty among the cosmetic products customers in Konya. The partial
least squares (PLS) method is used to analyze the survey data.
Findings of the present study revealed that experiential marketing has
been a significant predictor of customer satisfaction and customer
loyalty, and also experiential marketing has a significantly positive
effect on customer satisfaction and customer loyalty.
Abstract: The Composite Shear Walls (CSW) with steel encased
profiles can be used as lateral-load resisting systems for buildings
that require considerable large lateral-load capacity. The aim of this
work is to propose the experimental work conducted on CSW having
L section folded plate (L shape steel made-up sections) as
longitudinal reinforcement in boundary regions. The study in this
paper present the experimental test conducted on CSW having L
section folded plate as longitudinal reinforcement in boundary
regions. The tested 1/3 geometric scaled CSW has aspect ratio of 3.2.
L-shape structural steel materials with 2L-19x57x7mm dimensions
were placed in shear wall boundary zones. The seismic behavior of
CSW test specimen was investigated by evaluating and interpreting
the hysteresis curves, envelope curves, rigidity and consumed energy
graphs of this tested element. In addition to this, the experimental
results, deformation and cracking patterns were evaluated, interpreted
and suggestions of the design recommendations were proposed.
Abstract: Polyaniline is an indispensible component in lightemitting
devices (LEDs), televisions, cellular telephones, automotive,
corrosion-resistant coatings, actuators etc. The electrical conductivity
properties was found be increased by introduction of metal nano
particles. In the present study, an attempt has been made to utilize
platinum nano particles to achieve the improved electrical properties.
Polyaniline and Pt-polyaniline composite are synthesized by
electrochemical routes. X-ray diffractometer confirms the amorphous
nature of polyaniline. The Bragg’s diffraction peaks correspond to
platinum nanoparticles in Pt-polyaniline composite and
thermogravimetric analyzer indicates its decomposition at certain
temperature. The Scanning Electron Micrographs of colloidal
platinum nanoparticles were spherical, uniform shape in the
composite. The current-voltage (I-V) characteristics of the PANI and
composites were also studied which indicate a significant decreasing
resistivity than PANI-Platinum after introduction of pt nanoparticles
in the matrix of polyaniline (PANI).
Abstract: Several embryonic cellular mechanism including cell
cycle, growth and apoptosis are regulated by phosphatidylinositol-3-
kinase (PI3K)/Akt signaling pathway. The goal of present study is to
determine the effects of annatto (Bixa orellana)-derived δ-tocotrienol
(δ-TCT) on the regulations of PI3K/Akt genes in murine morula.
Twenty four 6-8 week old (23-25g) female balb/c mice were
randomly divided into four groups (G1-G4; n=6). Those groups were
subjected to the following treatments for 7 consecutive days: G1
(control) received tocopherol stripped corn oil, G2 was given 60
mg/kg/day of δ-TCT mixture (contains 90% delta & 10% gamma
isomers), G3 was given 60 mg/kg/day of pure δ-TCT (>98% purity)
and G4 received 60 mg/kg/day α-TOC. On Day 8, females were
superovulated with 5 IU Pregnant Mare’s Serum Gonadotropin
(PMSG) for 48 hours followed with 5 IU human Chorionic
Gonadotropin (hCG) before mated with males at the ratio of 1:1.
Females were sacrificed by cervical dislocation for embryo collection
48 hours post-coitum. About fifty morulas from each group were
used in the gene expression analyses using Affymetrix QuantiGene
Plex 2.0 Assay. Present data showed a significant increase (p
Abstract: The goal of this paper is to present the diagnostic
contribution that the screening instrument, Mini-Mental State
Examination-2: Expanded Version (MMSE-2:EV), brings in
detecting the cognitive impairment or in monitoring the progress of
degenerative disorders. The diagnostic signification is underlined by
the interpretation of the MMSE-2:EV scores, resulted from the test
application to patients with mild and major neurocognitive disorders.
The cases were selected from current practice, in order to cover vast
and significant neurocognitive pathology: mild cognitive impairment,
Alzheimer’s disease, vascular dementia, mixed dementia, Parkinson’s
disease, conversion of the mild cognitive impairment into
Alzheimer’s disease. The MMSE-2:EV version was used: it was
applied one month after the initial assessment, three months after the
first reevaluation and then every six months, alternating the blue and
red forms. Correlated with age and educational level, the raw scores
were converted in T scores and then, with the mean and the standard
deviation, the z scores were calculated. The differences of raw scores
between the evaluations were analyzed from the point of view of
statistic signification, in order to establish the progression in time of
the disease. The results indicated that the psycho-diagnostic approach
for the evaluation of the cognitive impairment with MMSE-2:EV is
safe and the application interval is optimal. In clinical settings with a
large flux of patients, the application of the MMSE-2:EV is a safe
and fast psychodiagnostic solution. The clinicians can draw objective
decisions and for the patients: it does not take too much time and
energy, it does not bother them and it doesn’t force them to travel
frequently.
Abstract: The output error of the globoidal cam mechanism can
be considered as a relevant indicator of mechanism performance,
because it determines kinematic and dynamical behavior of
mechanical transmission. Based on the differential geometry and the
rigid body transformations, the mathematical model of surface
geometry of the globoidal cam is established. Then we present the
analytical expression of the output error (including the transmission
error and the displacement error along the output axis) by considering
different manufacture and assembly errors. The effects of the center
distance error, the perpendicular error between input and output axes
and the rotational angle error of the globoidal cam on the output error
are systematically analyzed. A globoidal cam mechanism which is
widely used in automatic tool changer of CNC machines is applied for
illustration. Our results show that the perpendicular error and the
rotational angle error have little effects on the transmission error but
have great effects on the displacement error along the output axis. This
study plays an important role in the design, manufacture and assembly
of the globoidal cam mechanism.
Abstract: The MEMS pressure sensor has been introduced and
presented in this paper. The types of pressure sensor and its theory of
operation are also included. The latest MEMS technology, the
fabrication processes of pressure sensor are explored and discussed.
Besides, various device applications of pressure sensor such as tire
pressure-monitoring system, diesel particulate filter and others are
explained. Due to further miniaturization of the device nowadays, the
pressure sensor with nanotechnology (NEMS) is also reviewed. The
NEMS pressure sensor is expected to have better performance as well
as lower in its cost. It has gained an excellent popularity in many
applications.
Abstract: Nowadays, technological progress is one of the most
important components of economic growth and the efficiency of
R&D activities is particularly essential for countries. This study is an
attempt to analyze the R&D efficiencies of EU countries. The
indicators related to R&D efficiencies should be determined in
advance in order to use DEA. For this reason a list of input and
output indicators are derived from the literature review. Considering
the data availability, a final list is given for the numerical analysis for
future research.
Abstract: In recent years, fire accidents have been steadily
increased and the amount of property damage caused by the accidents
has gradually raised. Damaging building structure, fire incidents bring
about not only such property damage but also strength degradation and
member deformation. As a result, the building structure undermines its
structural ability. Examining the degradation and the deformation is
very important because reusing the building is more economical than
reconstruction. Therefore, engineers need to investigate the strength
degradation and member deformation well, and make sure that they
apply right rehabilitation methods. This study aims at evaluating
deformation characteristics of fire damaged and rehabilitated normal
strength concrete beams through both experiments and finite element
analyses. For the experiments, control beams, fire damaged beams and
rehabilitated beams are tested to examine deformation characteristics.
Ten test beam specimens with compressive strength of 21MPa are
fabricated and main test variables are selected as cover thickness of
40mm and 50mm and fire exposure time of 1 hour or 2 hours. After
heating, fire damaged beams are air-recurred for 2 months and
rehabilitated beams are repaired with polymeric cement mortar after
being removed the fire damaged concrete cover. All beam specimens
are tested under four points loading. FE analyses are executed to
investigate the effects of main parameters applied to experimental
study. Test results show that both maximum load and stiffness of the
rehabilitated beams are higher than those of the fire damaged beams.
In addition, predicted structural behaviors from the analyses also show
good rehabilitation effect and the predicted load-deflection curves are
similar to the experimental results. For the further, the proposed
analytical method can be used to predict deformation characteristics of
fire damaged and rehabilitated concrete beams without suffering from
time and cost consuming of experimental process.
Abstract: In this paper, we consider some integrable Heisenberg
Ferromagnet Equations with self-consistent potentials. We study
their Lax representations. In particular we derive their equivalent
counterparts in the form of nonlinear Schr¨odinger type equations.
We present the integrable reductions of the Heisenberg Ferromagnet
Equations with self-consistent potentials. These integrable Heisenberg
Ferromagnet Equations with self-consistent potentials describe
nonlinear waves in ferromagnets with some additional physical fields.
Abstract: Significant attention has recently been paid to the
cross-cultural negotiations due to the growth of international
businesses. Despite the substantial body of literature examining the
influence of National Culture (NC) dimensions on negotiations, there
is a lack of studies comparing the influence of NC in Latin America
with a Western European countries, In particular, an extensive review
of the literature revealed that a contribution to knowledge would be
derived from the comparison of the influence of NC dimensions on
negotiations in UK and Venezuela. The primary data was collected
through qualitative interviews, to obtain an insight about the
perceptions and beliefs of Venezuelan and British business managers
about their negotiating styles. The findings of this study indicated
that NC has a great influence on the negotiating styles. In particular,
Venezuelan and British managers demonstrated to have opposed
negotiating styles, affecting the way they communicate, approach
people and their willingness to take risks.