Abstract: The rate of natural gas dissociation from the Coal
Matrix depends on depressurization of reservoir through removing of
the cleat water from the coal seam. These waters are similar to brine
and aged of very long years. For improving the connectivity through
fracking /fracturing, high pressure liquids are pumped off inside the
coal body. A significant quantity of accumulated water, a combined
mixture of cleat water and fracking fluids (back flow water) is
pumped out through gas well. In Queensland, Australia Coal Seam
Gas (CSG) industry is in booming state and estimated of 30,000 wells
would be active for CSG production forecasting life span of 30 years.
Integrated water management along with water softening programs is
practiced for subsequent treatment and later on discharge to nearby
surface water catchment. Water treatment is an important part of the
CSG industry. A case study on a CSG site and review on the test
results are discussed for assessing the Standards & Practices for
management of CSG by-product water and their subsequent disposal
activities. This study was directed toward (i) water management and
softening process in Spring Gully CSG field, (ii) Comparative
analysis on experimental study and standards and (iii) Disposal of the
treated water. This study also aimed for alternative usages and their
impact on vegetation, living species as well as long term effects.
Abstract: In order to better understand the long term
implications of the grout wear failure mode in large-diameter plainsided
grouted connections, a numerical model has been developed
and calibrated that can take advantage of existing operational plant
data to predict the wear accumulation for the actual load conditions
experienced over a given period, thus limiting the requirement for
expensive monitoring systems. This model has been derived and
calibrated based on site structural condition monitoring (SCM) data
and supervisory control and data acquisition systems (SCADA) data
for two operational wind turbine generator substructures afflicted
with this challenge, along with experimentally derived wear rates.
Abstract: A capacity spectrum method (CSM), one of methodologies to evaluate seismic fragilities of building structures, has been long recognized as the most convenient method, even if it contains several limitations to predict the seismic response of structures of interest. This paper proposes the procedure to estimate seismic fragility curves using an incremental dynamic analysis (IDA) rather than the method adopting a CSM. To achieve the research purpose, this study compares the seismic fragility curves of a 5-story reinforced concrete (RC) moment frame obtained from both methods; an IDA method and aCSM. Both seismic fragility curves are similar in slight and moderate damage states whereas the fragility curve obtained from the IDA method presents less variation (or uncertainties) in extensive and complete damage states. This is due to the fact that the IDA method can properly capture the structural response beyond yielding rather than the CSM and can directly calculate higher mode effects. From these observations, the CSM could overestimate seismic vulnerabilities of the studied structure in extensive or complete damage states.
Abstract: The effect of the inclusion of thyme and rosemary
essential oils into chitosan films, as well as the microbiological and
physical properties when storing chitosan film with and without the
mentioned inclusion was studied. The film forming solution was
prepared by dissolving chitosan (2%, w/v), polysorbate 80 (4% w/w
CH) and glycerol (16% w/w CH) in aqueous lactic acid solutions
(control). The thyme (TEO) and rosemary (REO) essential oils (EOs)
were included 1:1 w/w (EOs:CH) on their combination 50/50
(TEO:REO). The films were stored at temperatures of 5, 20, 33°C
and a relative humidity of 75% during four weeks. The films with
essential oil inclusion did not show an antimicrobial activity against
strains. This behavior could be explained because the chitosan only
inhibits the growth of microorganisms in direct contact with the
active sites. However, the inhibition capacity of TEO was higher than
the REO and a synergic effect between TEO:REO was found for S.
enteritidis strains in the chitosan solution.
Some physical properties were modified by the inclusion of
essential oils. The addition of essential oils does not affect the
mechanical properties (tensile strength, elongation at break, puncture
deformation), the water solubility, the swelling index nor the DSC
behavior. However, the essential oil inclusion can significantly
decrease the thickness, the moisture content, and the L* value of
films whereas the b* value increased due to molecular interactions
between the polymeric matrix, the loosing of the structure, and the
chemical modifications. On the other hand, the temperature and time
of storage changed some physical properties on the chitosan films.
This could have occurred because of chemical changes, such as
swelling in the presence of high humidity air and the reacetylation of
amino groups. In the majority of cases, properties such as moisture
content, tensile strength, elongation at break, puncture deformation,
a*, b*, chrome, 7E increased whereas water resistance, swelling
index, L*, and hue angle decreased.
Abstract: In the last few decades, many southeast-Asia women
migrate to Taiwan by marriage, and it usually takes several years for
them to acquire Taiwanese citizenship. This study investigates the
relationship between their citizenship acquisition and whether they
develop Taiwanese identities, and how does it affect their ethnical
identity towards their original ethnics. Furthermore, the present study
also explores that whether citizenship acquisition help the immigrant
women to explore the host society further and make commitment to it,
or the identification towards mainstream Taiwanese society is only
symbolic and superficial? One hundred and ninety-two immigrant
women were measured using Multigroup Ethnic Identity
Measure-Revised and a global 10-point ethnic identity question.
Correlation tests, t-test, and hierarchical regression were performed to
answer the above questions. The results revealed that citizenship
acquisition does help immigrant women to identify with Taiwanese
society, but it does not affect how they identify with their own ethnics.
Furthermore, the results also indicated that acquiring citizenship
would not help these immigrant women become involved in deeper
cultural exploration of Taiwan nor would it encourage them to make
commitments to the host society.
Abstract: The design, manufacture, and operation of thin-walled
pressure vessels must be based on maximum safe operating pressure
and an adequate factor of safety (FoS). This research paper first
reports experimental evaluation of longitudinal and hoops stresses
based on working pressure as well as maximum pressure; and then
includes a critical study of factor of safety (FoS) in the design of a
glass fiber pressure vessel. Experimental work involved the use of
measuring instruments and the readings from pressure gauges.
Design calculations involved the computations of design stress and
FoS; the latter was based on breaking strength of 55 MPa for the
glass fiber (pressure-vessel material). The experimentally determined
FoS value has been critically compared with the general FoS allowed
in the design of glass fiber pressure vessels.
Abstract: The present study was carried out to evaluate the
effect of different levels of dietary seed and extract of Harmal
(Peganum harmala L.) on immunity of broiler chicks. A total of 350
one-day old broiler chicks (Ross 308) were randomly allocated to
five dietary treatments with four replicates pen of 14 birds each.
Dietary treatments consisted of control, 1 and 2 g/kg Harmal seed in
diet, 100 and 200 mg/L Harmal seed extract in water. Broilers
received dietary treatments from 1 to 42 d. Two birds from each pen
were randomly weighed and sacrificed at 42 d of age, the relative
weight of lymphoid organs (bursa of Fabercius and spleen) to live
weight were calculated. Antibody titers against Newcastle and
influenza viruses and sheep red blood cell were measured at 30 d of
age. Results showed that the relative weights of lymphoid organs
were not affected by dietary treatments. Furthermore, antibody titer
against Newcastle and influenza viruses as well as sheep red blood
cell antigen were significantly (P
Abstract: Chemical Reaction Optimization (CRO) is an
optimization metaheuristic inspired by the nature of chemical
reactions as a natural process of transforming the substances from
unstable to stable states. Starting with some unstable molecules with
excessive energy, a sequence of interactions takes the set to a state of
minimum energy. Researchers reported successful application of the
algorithm in solving some engineering problems, like the quadratic
assignment problem, with superior performance when compared with
other optimization algorithms. We adapted this optimization
algorithm to the Printed Circuit Board Drilling Problem (PCBDP)
towards reducing the drilling time and hence improving the PCB
manufacturing throughput. Although the PCBDP can be viewed as
instance of the popular Traveling Salesman Problem (TSP), it has
some characteristics that would require special attention to the
transactions that explore the solution landscape. Experimental test
results using the standard CROToolBox are not promising for
practically sized problems, while it could find optimal solutions for
artificial problems and small benchmarks as a proof of concept.
Abstract: To date, one of the few comprehensive indicators for
the measurement of food security is the Global Food Security Index
(GFSI). This index is a dynamic quantitative and qualitative
benchmarking model, constructed from 28 unique indicators, that
measures drivers of food security across both developing and
developed countries. Whereas the GFSI has been calculated across a
set of 109 countries, in this paper we aim to present and compare, for
the Middle East and North Africa (MENA), 1) the Food Security
Index scores achieved and 2) the data available on affordability,
availability, and quality of food. The data for this work was taken
from the latest available report published by the creators of the GFSI,
which in turn used information from national and international
statistical sources. MENA countries rank from place 17/109 (Israel,
although with resent political turmoil this is likely to have changed)
to place 91/109 (Yemen) with household expenditure spent in food
ranging from 15.5% (Israel) to 60% (Egypt). Lower spending on food
as a share of household consumption in most countries and better
food safety net programs in the MENA have contributed to a notable
increase in food affordability. The region has also, however,
experienced a decline in food availability, owing to more limited
food supplies and higher volatility of agricultural production. In
terms of food quality and safety the MENA has the top ranking
country (Israel). The most frequent challenges faced by the countries
of the MENA include public expenditure on agricultural research and
development as well as volatility of agricultural production. Food
security is a complex phenomenon that interacts with many other
indicators of a country’s wellbeing; in the MENA it is slowly but
markedly improving.
Abstract: This paper presents analysis and design of a wideband
Wilkinson power divider for wireless applications. The design is
accomplished by transforming the lengths and impedances of the
quarter wavelength sections of the conventional Wilkinson power
divider into U-shaped sections. The designed power divider is
simulated by using ADS Agilent technologies and CST microwave
studio software. It is shown that the proposed power divider has
simple topology and good performances in terms of insertion loss,
port matching and isolation at all operating frequencies (1.8 GHz,
2.45 GHz and 3.55 GHz).
Abstract: A thermosyphon system is a heat transfer loop which
operates on the basis of gravity and buoyancy forces. It guarantees a
good reliability and low maintenance cost as it does not involve any
mechanical pump. Therefore, it can be used in many industrial
applications such as refrigeration and air conditioning, electronic
cooling, nuclear reactors, geothermal heat extraction, etc. But flow
instabilities and loop configuration are the major problems in this
system. Several previous researchers studied that stabilities can be
suppressed by using nanofluids as loop fluid. In the present study a
rectangular thermosyphon loop with end heat exchangers are
considered for the study. This configuration is more appropriate for
many practical applications such as solar water heater, geothermal
heat extraction, etc. In the present work, steady-state analysis is
carried out on thermosyphon loop with parallel flow coaxial heat
exchangers at heat source and heat sink. In this loop nanofluid is
considered as the loop fluid and water is considered as the external
fluid in both hot and cold heat exchangers. For this analysis onedimensional
homogeneous model is developed. In this model,
conservation equations like conservation of mass, momentum, energy
are discretized using finite difference method. A computer code is
written in MATLAB to simulate the flow in thermosyphon loop. A
comparison in terms of heat transfer is made between water and
nanofluid as working fluids in the loop.
Abstract: In this paper, the transient device performance analysis
of n-type Gate Inside JunctionLess Transistor (GI-JLT) has been
evaluated. 3-D Bohm Quantum Potential (BQP) transport device
simulation has been used to evaluate the delay and power dissipation
performance. GI-JLT has a number of desirable device parameters
such as reduced propagation delay, dynamic power dissipation,
power and delay product, intrinsic gate delay and energy delay
product as compared to Gate-all-around transistors GAA-JLT. In
addition to this, various other device performance parameters namely,
on/off current ratio, short channel effects (SCE), transconductance
Generation Factor (TGF) and unity gain cut-off frequency (fT ) and
subthreshold slope (SS) of the GI-JLT and GAA-JLT have been
analyzed and compared. GI-JLT shows better device performance
characteristics than GAA-JLT for low power and high frequency
applications, because of its larger gate electrostatic control on the
device operation.
Abstract: Given the dynamic nature of the higher education
landscape, induction programmes for new academics has become the
norm nowadays to support academics negotiate these rough terrain.
This study investigates an induction programme for new academics
in a higher education institution to establish what difference it has
made to participants. The findings revealed that the benefits ranged
from creating safe spaces for collaboration and networking to
fostering reflective practice and contributing to the scholarship of
teaching and learning. The study also revealed that some of the
intentions of the programme may not have been achieved, for
example transformative learning. This led to questioning whether this
intention is an appropriate one given the short duration of the
programme and the long, drawn out process of transformation. It may
be concluded that the academic induction programme in this study
serves to sow the seeds for transformative learning through fostering
critically reflective practice. Recommendations for further study
could include long term impact of the programme on student learning
and success, these being the core business of higher education. It is
also recommended that in addition to an induction programme, the
university invests in a mentoring programme for new staff and extend
the support for academics in order to sustain critical reflection and
which may contribute to transformative educational practice.
Abstract: The final energy use can be divided mainly in four sectors: commercial, industrial, residential, and transportation. The trend in final energy consumption by sector plays as a most straightforward way to provide a wide indication of progress for reducing energy consumption and associated environmental impacts by different end use sectors. The average share of end use energy for residential sector in the world was nearly 20% until 2011, in Germany a higher proportion is between 25% and 30%. However, it remains less studied than energy use in other three sectors as well its impacts on climate and environment. The reason for this involves a wide range of fields, including the diversity of residential construction like different housing building design and materials, living or energy using behavioral patterns, climatic condition and variation as well other social obstacles, market trend potential and financial support from government.
This paper presents an extensive and in-depth analysis of the manner by which projects researched and operated by authors in the fields of energy efficiency primarily from the perspectives of both technical potential and initiative energy saving consciousness in the residential sectors especially in social housing buildings.
Abstract: A strain of Monascus purpureus CMU001 was used to
prepare red yeast rice from Thai glutinous rice Korkor 6 (RD 6).
Adding of different amounts of histidine (156, 312, 625 and 1250 mg
in 100 g of rice grains)) under aerobic and air limitation (air-lock)
condition were used in solid fermentation. Determination of the yield
as well as monacolin K content was done. Citrinin content was also
determined in order to confirm the safety use of prepared red yeast
rice. It was found that under air-lock condition with 1250 mg of
histidine addition gave the highest yield of 37.40 g of dried red yeast
rice prepared from 100 g of rice. Highest 5.72 mg content of
monacolin K was obtained under air-lock condition with 312 mg
histidine addition. In the other hand, citrinin content was found to be
less than 24462 ng/g of all dried red yeast rice samples under the
experimental methods used in this work.
Abstract: Wireless mesh networking is rapidly gaining in
popularity with a variety of users: from municipalities to enterprises,
from telecom service providers to public safety and military
organizations. This increasing popularity is based on two basic facts:
ease of deployment and increase in network capacity expressed in
bandwidth per footage; WMNs do not rely on any fixed
infrastructure. Many efforts have been used to maximizing
throughput of the network in a multi-channel multi-radio wireless
mesh network. Current approaches are purely based on either static or
dynamic channel allocation approaches. In this paper, we use a
hybrid multichannel multi radio wireless mesh networking
architecture, where static and dynamic interfaces are built in the
nodes. Dynamic Adaptive Channel Allocation protocol (DACA), it
considers optimization for both throughput and delay in the channel
allocation. The assignment of the channel has been allocated to be codependent
with the routing problem in the wireless mesh network and
that should be based on passage flow on every link. Temporal and
spatial relationship rises to re compute the channel assignment every
time when the pattern changes in mesh network, channel assignment
algorithms assign channels in network. In this paper a computing
path which captures the available path bandwidth is the proposed
information and the proficient routing protocol based on the new path
which provides both static and dynamic links. The consistency
property guarantees that each node makes an appropriate packet
forwarding decision and balancing the control usage of the network,
so that a data packet will traverse through the right path.
Abstract: Worldwide, most PILC MV underground cables in use
are approaching the end of their design life; hence, failures are likely
to increase. This paper studies the electric field and potential
distributions within the PILC insulted cable containing common
void-defect. The finite element model of the performance of the
belted PILC MV underground cable is presented. The variation of the
electric field stress within the cable using the Finite Element Method
(FEM) is concentrated. The effects of the void-defect within the
insulation are given. Outcomes will lead to deeper understanding of
the modeling of Paper Insulated Lead Covered (PILC) and electric
field response of belted PILC insulted cable containing void defect.
Abstract: Karst term is the determiner of a variety of areas or
landforms and unique perspectives that have been formed in result of
the of the ingredients dissolution of rocks constituter by natural
waters. Shiraz area with an area of 5322km2 is located in the simple
folded belt in the southern part of Zagros Mountain of Fars, and is
surrounded with Limestone Mountains (Asmari formation). Shiraz
area is located in Calcareous areas. The infrastructure of this city is
lime and absorbing wells that the city can influence the Limestone
dissolution and those accelerate its rate and increase the cavitation
below the surface. Dasht-e Arjan is a graben, which has been created
as the result of activity of two normal faults in its east and west sides.
It is a complete sample of Karst plains (Polje) which has been created
with the help of tectonic forces (fault) and dissolution process of
water in Asmari limestone formation. It is located 60km. off south
west of Shiraz (on Kazeroon-Shiraz road). In 1971, UNESCO has
recognized this plain as a reserve of biosphere. It is considered as one
of the world’s most beautiful geological phenomena, so that most of
the world’s geologists are interested in visiting this place. The
purpose of this paper is to identify and introduce landscapes of Karst
features shiraz city and Dasht-e Arjan including Karst dissolution
features (Lapiez, Karst springs, dolines, caves, underground caves,
ponors, and Karst valleys), anticlines and synclines, and Arjan Lake.
Abstract: Cloud computing (CC) has already gained overall
appreciation in research and practice. Whereas the willingness to
integrate cloud services in various IT environments is still unbroken,
the previous CC procurement processes run mostly in an unorganized
and non-standardized way. In practice, a sufficiently specific, yet
applicable business process for the important acquisition phase is
often lacking. And research does not appropriately remedy this
deficiency yet. Therefore, this paper introduces a field-tested
approach for CC procurement. Based on an extensive literature
review and augmented by expert interviews, we designed a model
that is validated and further refined through an in-depth real-life case
study. For the detailed process description, we apply the event-driven
process chain notation (EPC). The gained valuable insights into the
case study may help CC research to shift to a more socio-technical
area. For practice, next to giving useful organizational instructions
we will provide extended checklists and lessons learned.
Abstract: Replacement of plastics used in the food industry
seems to be a serious issue to overcome mainly the environmental
problems in recent years. This study investigates the hydrophilicity
and permeability properties of starch biopolymer which ethylene
vinyl alcohol (EVOH) (0-10%) and nanocrystalline cellulose (NCC)
(1-15%) were used to enhance its properties. Starch -EVOH
nanocomposites were prepared by casting method in different
formulations. NCC production by acid hydrolysis was confirmed by
scanning electron microscopy. Solubility, water vapor permeability,
water vapor transmission rate and moisture absorbance were
measured on each of the nanocomposites. The results were analyzed
by SAS software. The lowest moisture absorbance was measured in
pure starch nanocomposite containing 8% NCC. The lowest
permeability to water vapor belongs to starch nanocomposite
containing 8% NCC and the sample containing 7.8% EVOH and 13%
NCC. Also the lowest solubility was observed in the composite
contains the highest amount of EVOH. Applied Process resulted in
production of bio films which have good resistance to water vapor
permeability and solubility in water. The use of NCC and EVOH
leads to reduced moisture absorbance property of the biofilms.