Abstract: Power Factor (PF) is one of the most important parameters in the electrical systems, especially in the water pumping station. The low power factor value of the water pumping stations causes penalty for the electrical bill. There are many methods use for power factor improvement. Each one of them uses a capacitor on the electrical power network. The position of the capacitors is varied depends on many factors such as; voltage level and capacitors rating. Adding capacitors on the motor terminals increase the supply power factor from 0.8 to more than 0.9 but these capacitors cause some problems for the electrical grid network, such as increasing the harmonic contents of the grid line voltage. In this paper the effects of using capacitors in the water pumping stations to improve the power factor value on the harmonic contents of the electrical grid network are studied. One of large water pumping stations in Kafr El-Shikh Governorate in Egypt was used, as a case study. The effect of capacitors on the line voltage harmonic contents is measured. The station uses capacitors to improve the PF values at the 1 lkv grid network. The power supply harmonics values are measured by a power quality analyzer at different loading conditions. The results showed that; the capacitors improved the power factor value of the feeder and its value increased than 0.9. But the THD values are increased by adding these capacitors. The harmonic analysis showed that; the 13th, 17th, and 19th harmonics orders are increased also by adding the capacitors.
Abstract: A new Meta heuristic approach called "Randomized gravitational emulation search algorithm (RGES)" for solving vertex covering problems has been designed. This algorithm is found upon introducing randomization concept along with the two of the four primary parameters -velocity- and -gravity- in physics. A new heuristic operator is introduced in the domain of RGES to maintain feasibility specifically for the vertex covering problem to yield best solutions. The performance of this algorithm has been evaluated on a large set of benchmark problems from OR-library. Computational results showed that the randomized gravitational emulation search algorithm - based heuristic is capable of producing high quality solutions. The performance of this heuristic when compared with other existing heuristic algorithms is found to be excellent in terms of solution quality.
Abstract: The effect of variable chemical reaction on heat and mass transfer characteristics over unsteady stretching surface embedded in a porus medium is studied. The governing time dependent boundary layer equations are transformed into ordinary differential equations containing chemical reaction parameter, unsteadiness parameter, Prandtl number and Schmidt number. These equations have been transformed into a system of first order differential equations. MATHEMATICA has been used to solve this system after obtaining the missed initial conditions. The velocity gradient, temperature, and concentration profiles are computed and discussed in details for various values of the different parameters.
Abstract: In this paper, an automated system is presented for
identification and separation of plastic resins based on near infrared
(NIR) reflectance spectroscopy. For identification and separation
among resins, a "Two-Filter" identification method is proposed that
is capable to distinguish among polyethylene terephthalate (PET),
high density polyethylene (HDPE), polyvinyl chloride (PVC),
polypropylene (PP) and polystyrene (PS). Through surveying effects
of parameters such as surface contamination, sample thickness, label
and cap existence, it was obvious that the "Two-Filter" method has a
high efficiency in identification of resins. It is shown that accurate
identification and separation of five major resins can be obtained
through calculating the relative reflectance at two wavelengths in the
NIR region.
Abstract: The aim of this paper is to compare the effectiveness and electrochemical behavior of typical oilfield corrosion inhibitors with previous oilfield corrosion inhibitors under the same electrochemical techniques to control preferential weld corrosion of X65 pipeline steel in artificial seawater saturated with carbon dioxide at a pressure of one bar. A secondary aim is to investigate the conditions under which current reversal takes place. A flow channel apparatus was used in the laboratory to simulate the actual condition that occurs in marine pipelines. Different samples from the parent metal, the weld metal and the heat affected zone in the pipeline steel were galvanically coupled. The galvanic currents flowing between the weld regions were recorded using zero-resistance ammeters and tested under static and flowing conditions in both inhibited and uninhibited media. The results show that a current reversal took place when 30ppm of both green oilfield inhibitors were present, resulting in accelerated weld corrosion.
Abstract: An effort to find out the smaller size of cuttings for propagation of Morus alba was made in experimental area Department of Forestry, Range Management and Wildlife, University of Agriculture, Faisalabad, Pakistan. Different size of cuttings i.e. 2", 4", 6" and 8" were planted in polythene tubes of 3.5"x7". The effort was also made to compare the performance of cuttings in open air and in polythene low tunnel. Root length, number of root branches, root diameter and root fresh and dry weight were found maximum in two inches cuttings while minimum in four inches cuttings. Root growth was found maximum in open air as compared to under polythene sheet.
Abstract: Presence of phytosterol compound in Durian seed
(Durio zibethinus) or known as King of fruits has been discovered
from screening work using reagent test. Further analysis work has
been carried out using mass spectrometer in order to support the
priliminary finding. Isolation and purification of the major
phytosterol has been carried out using an open column
chromatography. The separation was monitored using thin layer
chromatography (TLC). Major isolated compounds and purified
phytosterol were identified using mass spectrometer and nuclear
magnetic resonance (NMR). This novel finding could promote
utilization of durian seeds as a functional ingredient in food products
through production of standardized extract based on phytosterol
content.
Abstract: In this paper, we propose the variational approach to solve single image defogging problem. In the inference process of the atmospheric veil, we defined new functional for atmospheric veil that satisfy edge-preserving regularization property. By using the fundamental lemma of calculus of variations, we derive the Euler-Lagrange equation foratmospheric veil that can find the maxima of a given functional. This equation can be solved by using a gradient decent method and time parameter. Then, we can have obtained the estimated atmospheric veil, and then have conducted the image restoration by using inferred atmospheric veil. Finally we have improved the contrast of restoration image by various histogram equalization methods. The experimental results show that the proposed method achieves rather good defogging results.
Abstract: Boron minerals are very useful for various industrial
activities, such as glass industry and detergent industry, due to its
mechanical and chemical properties. During the production of boron
compounds, many of these are introduced into the environment in the
form of waste. Boron is also an important micro nutrient for the
plants to vegetate but if it exists in high concentrations, it could have
toxic effects. The maximum boron level in drinking water for human
health is given as 0.3 mg/L in World Health Organization (WHO)
standards. The toxic effects of boron should be noted especially for
dry regions, thus, in recent years, increasing attention has been paid
to remove the boron from waste waters. In this study, boron removal
is implemented by ion exchange process using Amberlite IRA-743
resin. Amberlite IRA-743 resin is a boron specific resin and it
belongs to the polymerizate sorbent group within the aminopolyol
functional group. Batch studies were performed to investigate the
effects of various experimental parameters, such as adsorbent dose,
initial concentration and pH, on the removal of boron. It is found
that, when the adsorbent dose increases removal of boron from the
liquid phase increases. However, an increase in the initial
concentration decreases the removal of boron. The effective pH
values for removal of boron are determined between 8.5 and 9.
Equilibrium isotherms were also analyzed by Langmuir and
Freundlich isotherm models. The Langmuir isotherm is obeyed better
than the Freundlich isotherm.
Abstract: In the process of polyethylene extrusion polymer
material similar to powder or granule is under compression, melting
and transmission operation and on base of special form, extrudate has
been produced. Twin-screw extruders are applicable in industries
because of their high capacity. The powder mixing with chemical
additives and melting with thermal and mechanical energy in three
zones (feed, compression and metering zone) and because of gear
pump and screw's pressure, converting to final product in latest plate.
Extruders with twin-screw and short distance between screws are
better than other types because of their high capacity and good
thermal and mechanical stress.
In this paper, process of polyethylene extrusion and various tapes
of extruders are studied. It is necessary to have an exact control on
process to producing high quality products with safe operation and
optimum energy consumption.
The granule size is depending on granulator motor speed. Results
show at constant feed rate a decrease in granule size was found whit
Increase in motor speed. Relationships between HDPE feed rate and
speed of granulator motor, main motor and gear pump are calculated
following as:
x = HDPE feed flow rate, yM = Main motor speed
yM = (-3.6076e-3) x^4+ (0.24597) x^3+ (-5.49003) x^2+ (64.22092)
x+61.66786 (1)
x = HDPE feed flow rate, yG = Gear pump speed
yG = (-2.4996e-3) x^4+ (0.18018) x^3+ (-4.22794) x^2+ (48.45536)
x+18.78880 (2)
x = HDPE feed flow rate, y = Granulator motor speed
10th Degree Polynomial Fit: y = a+bx+cx^2+dx^3... (3)
a = 1.2751, b = 282.4655, c = -165.2098,
d = 48.3106, e = -8.18715, f = 0.84997
g = -0.056094, h = 0.002358, i = -6.11816e-5
j = 8.919726e-7, k = -5.59050e-9
Abstract: This paper presents the results related to the
interference reduction technique in multistage multiuser detector for
asynchronous DS-CDMA system. To meet the real-time
requirements for asynchronous multiuser detection, a bit streaming,
cascade architecture is used. An asynchronous multiuser detection
involves block-based computations and matrix inversions. The paper
covers iterative-based suboptimal schemes that have been studied to
decrease the computational complexity, eliminate the need for matrix
inversions, decreases the execution time, reduces the memory
requirements and uses joint estimation and detection process that
gives better performance than the independent parameter estimation
method. The stages of the iteration use cascaded and bits processed
in a streaming fashion. The simulation has been carried out for
asynchronous DS-CDMA system by varying one parameter, i.e.,
number of users. The simulation result exhibits that system gives
optimum bit error rate (BER) at 3rd stage for 15-users.
Abstract: A modified Genetic Algorithm (GA) based optimal selection of parameters for Automatic Generation Control (AGC) of multi-area electric energy systems is proposed in this paper. Simulations on multi-area reheat thermal system with and without consideration of nonlinearity like governor dead band followed by 1% step load perturbation is performed to exemplify the optimum parameter search. In this proposed method, a modified Genetic Algorithm is proposed where one point crossover with modification is employed. Positional dependency in respect of crossing site helps to maintain diversity of search point as well as exploitation of already known optimum value. This makes a trade-off between exploration and exploitation of search space to find global optimum in less number of generations. The proposed GA along with decomposition technique as developed has been used to obtain the optimum megawatt frequency control of multi-area electric energy systems. Time-domain simulations are conducted with trapezoidal integration along with decomposition technique. The superiority of the proposed method over existing one is verified from simulations and comparisons.
Abstract: This paper emphasizes on the application of genetic algorithm (GA) to optimize the parameters of the TMD for achieving the best results in the reduction of the building response under earthquake excitations. The Integral of the Time multiplied Absolute value of the Error (ITAE) based on relative displacement of all floors in the building is taken as a performance index of the optimization criterion. The problem of robustly TMD controller design is formatted as an optimization problem based on the ITAE performance index to be solved using GA that has a story ability to find the most optimistic results. An 11–story realistic building, located in the city of Rasht, Iran is considered as a test system to demonstrate effectiveness of the proposed GA based TMD (GATMD) controller without specifying which mode should be controlled. The results of the proposed GATMD controller are compared with the uncontrolled structure through timedomain simulation and some performance indices. The results analysis reveals that the designed GA based TMD controller has an excellent capability in reduction of the seismically excited example building and the ITAE performance, that is so for remains as unknown, can be introduced a new criteria - method for structural dynamic design.
Abstract: Exponentially weighted moving average control chart (EWMA) is a popular chart used for detecting shift in the mean of parameter of distributions in quality control. The objective of this paper is to compare the efficiency of control chart to detect an increases in the mean of a process. In particular, we compared the Maximum Exponentially Weighted Moving Average (MaxEWMA) and Maximum Generally Weighted Moving Average (MaxGWMA) control charts when the observations are Exponential distribution. The criteria for evaluate the performance of control chart is called, the Average Run Length (ARL). The result of comparison show that in the case of process is small sample size, the MaxEWMA control chart is more efficiency to detect shift in the process mean than MaxGWMA control chart. For the case of large sample size, the MaxEWMA control chart is more sensitive to detect small shift in the process mean than MaxGWMA control chart, and when the process is a large shift in mean, the MaxGWMA control chart is more sensitive to detect mean shift than MaxEWMA control chart.
Abstract: The overall objective of this paper is to retrieve soil
surfaces parameters namely, roughness and soil moisture related to
the dielectric constant by inverting the radar backscattered signal
from natural soil surfaces.
Because the classical description of roughness using statistical
parameters like the correlation length doesn't lead to satisfactory
results to predict radar backscattering, we used a multi-scale
roughness description using the wavelet transform and the Mallat
algorithm. In this description, the surface is considered as a
superposition of a finite number of one-dimensional Gaussian
processes each having a spatial scale. A second step in this study
consisted in adapting a direct model simulating radar backscattering
namely the small perturbation model to this multi-scale surface
description. We investigated the impact of this description on radar
backscattering through a sensitivity analysis of backscattering
coefficient to the multi-scale roughness parameters.
To perform the inversion of the small perturbation multi-scale
scattering model (MLS SPM) we used a multi-layer neural network
architecture trained by backpropagation learning rule. The inversion
leads to satisfactory results with a relative uncertainty of 8%.
Abstract: Let G be a fuzzy graph. Then D Ôèå V is said to be a strong (weak) fuzzy dominating set of G if every vertex v ∈ V -D is strongly (weakly) dominated by some vertex u in D. We denote a strong (weak) fuzzy dominating set by sfd-set (wfd-set). The minimum scalar cardinality of a sfd-set (wfd-set) is called the strong (weak) fuzzy domination number of G and it is denoted by γsf (G)γwf (G). In this paper we introduce the concept of strong (weak) domination in fuzzy graphs and obtain some interesting results for this new parameter in fuzzy graphs.
Abstract: Efficient and safe plant operation can only be
achieved if the operators are able to monitor all key process
parameters. Instrumentation is used to measure many process
variables, like temperatures, pressures, flow rates, compositions or
other product properties. Therefore Performance monitoring is a
suitable tool for operators. In this paper, we integrate rigorous
simulation model, data reconciliation and parameter estimation to
monitor process equipments and determine key performance
indicator (KPI) of them. The applied method here has been
implemented in two case studies.
Abstract: This work presents a recursive identification algorithm. This algorithm relates to the identification of closed loop system with Variable Structure Controller. The approach suggested includes two stages. In the first stage a genetic algorithm is used to obtain the parameters of switching function which gives a control signal rich in commutations (i.e. a control signal whose spectral characteristics are closest possible to those of a white noise signal). The second stage consists in the identification of the system parameters by the instrumental variable method and using the optimal switching function parameters obtained with the genetic algorithm. In order to test the validity of this algorithm a simulation example is presented.
Abstract: We constructed a method of noise reduction for
JPEG-compressed image based on Bayesian inference using the
maximizer of the posterior marginal (MPM) estimate. In this method,
we tried the MPM estimate using two kinds of likelihood, both of
which enhance grayscale images converted into the JPEG-compressed
image through the lossy JPEG image compression. One is the
deterministic model of the likelihood and the other is the probabilistic
one expressed by the Gaussian distribution. Then, using the Monte
Carlo simulation for grayscale images, such as the 256-grayscale
standard image “Lena" with 256 × 256 pixels, we examined the
performance of the MPM estimate based on the performance measure
using the mean square error. We clarified that the MPM estimate via
the Gaussian probabilistic model of the likelihood is effective for
reducing noises, such as the blocking artifacts and the mosquito noise,
if we set parameters appropriately. On the other hand, we found that
the MPM estimate via the deterministic model of the likelihood is not
effective for noise reduction due to the low acceptance ratio of the
Metropolis algorithm.
Abstract: Most integrated inertial navigation systems (INS) and
global positioning systems (GPS) have been implemented using the
Kalman filtering technique with its drawbacks related to the need for
predefined INS error model and observability of at least four
satellites. Most recently, a method using a hybrid-adaptive network
based fuzzy inference system (ANFIS) has been proposed which is
trained during the availability of GPS signal to map the error
between the GPS and the INS. Then it will be used to predict the
error of the INS position components during GPS signal blockage.
This paper introduces a genetic optimization algorithm that is used to
update the ANFIS parameters with respect to the INS/GPS error
function used as the objective function to be minimized. The results
demonstrate the advantages of the genetically optimized ANFIS for
INS/GPS integration in comparison with conventional ANFIS
specially in the cases of satellites- outages. Coping with this problem
plays an important role in assessment of the fusion approach in land
navigation.