Abstract: In recent years, rehabilitation has been the subject of extensive research due to increased spending on building work and repair of built works. In all cases, it is absolutely essential to carry out methods of strengthening or repair of structural elements, and that following an inspection analysis and methodology of a correct diagnosis. The reinforced concrete columns are important elements in building structures. They support the vertical loads and provide bracing against the horizontal loads. This research about the behavior of reinforced concrete rectangular columns, rehabilitated by concrete liner, confinement FRP fabric, steel liner or cage formed by metal corners. It allows comparing the contributions of different processes used perspective section resistance elements rehabilitated compared to that is not reinforced or repaired. The different results obtained revealed a considerable gain in bearing capacity failure of reinforced sections cladding concrete, metal bracket, steel plates and a slight improvement to the section reinforced with fabric FRP. The use of FRP does not affect the weight of the structures, but the use of different techniques cladding increases the weight of elements rehabilitated and therefore the weight of the building which requires resizing foundations.
Abstract: Accurate assessment of the primary tumor response to
treatment is important in the management of breast cancer. This
paper introduces a new set of treatment evaluation indicators for
breast cancer cases based on the computational process of three
known metrics, the Euclidian, Hamming and Levenshtein distances.
The distance principals are applied to pairs of mammograms and/or
echograms, recorded before and after treatment, determining a
reference point in judging the evolution amount of the studied
carcinoma. The obtained numerical results are indeed very
transparent and indicate not only the evolution or the involution of
the tumor under treatment, but also a quantitative measurement of the
benefit in using the selected method of treatment.
Abstract: This article presents a method for elections between the members of a group that is founded by fuzzy logic. Linguistic variables are objects for decision on election cards and deduction is based on t-norms and s-norms. In this election-s method election cards are questionnaire. The questionnaires are comprised of some questions with some choices. The choices are words from natural language. Presented method is accompanied by center of gravity (COG) defuzzification added up to a computer program by MATLAB. Finally the method is illustrated by solving two examples; choose a head for a research group-s members and a representative for students.
Abstract: This paper contributes to the field of Environmental
Awareness Training (EAT) evaluation in terms of military activities.
Environmental management of military activities is a growing concern
for defence forces worldwide and the importance of EAT is becoming
widely recognized. As one of Australia-s largest landowners, the
Australian Defence Force (ADF) is extremely mindful of its duty as a
joint environmental manager. It has an integrated Environmental
Management System (EMS) to assist environmental management and
EAT is an essential part of the ADF EMS model. This paper examines
how EAT was conducted during the exercise Talisman Saber in 2009
(TS09) and evaluates its effectiveness, using Shoalwater Bay Training
Area (SWBTA), one of the most significant military training areas and
a significant protected area in Australia, as a case study. A
questionnaire survey conducted showed, overall, that EAT was
effective from the perspective of a sample of participants.
Recommendations are made for the ADF to refine EAT for future
exercises.
Abstract: Computational study of two dimensional supersonic reacting hydrogen-air flows is performed to investigate the nitrogen effects on ignition delay time for premixed and diffusion flames. Chemical reaction is treated using detail kinetics and the advection upstream splitting method is used to calculate the numerical inviscid fluxes. The results show that just in stoichiometric condition for both premixed and diffusion flames, there is monotone dependency of the ignition delay time to the nitrogen addition. In other situations, the optimal condition from ignition viewpoint should be found using numerical investigations.
Abstract: Microtomographic images and thin section (TS)
images were analyzed and compared against some parameters of
geological interest such as porosity and its distribution along the
samples. The results show that microtomography ( CT) analysis,
although limited by its resolution, have some interesting information
about the distribution of porosity (homogeneous or not) and can also
quantify the connected and non-connected pores, i.e., total porosity.
TS have no limitations concerning resolution, but are limited by the
experimental data available in regards to a few glass sheets for
analysis and also can give only information about the connected
pores, i.e., effective porosity. Those two methods have their own
virtues and flaws but when paired together they are able to
complement one another, making for a more reliable and complete
analysis.
Abstract: Segmentation is an important step in medical image
analysis and classification for radiological evaluation or computer
aided diagnosis. The CAD (Computer Aided Diagnosis ) of lung CT
generally first segment the area of interest (lung) and then analyze
the separately obtained area for nodule detection in order to
diagnosis the disease. For normal lung, segmentation can be
performed by making use of excellent contrast between air and
surrounding tissues. However this approach fails when lung is
affected by high density pathology. Dense pathologies are present in
approximately a fifth of clinical scans, and for computer analysis
such as detection and quantification of abnormal areas it is vital that
the entire and perfectly lung part of the image is provided and no
part, as present in the original image be eradicated. In this paper we
have proposed a lung segmentation technique which accurately
segment the lung parenchyma from lung CT Scan images. The
algorithm was tested against the 25 datasets of different patients
received from Ackron Univeristy, USA and AGA Khan Medical
University, Karachi, Pakistan.
Abstract: The empirical mode decomposition (EMD) represents any time series into a finite set of basis functions. The bases are termed as intrinsic mode functions (IMFs) which are mutually orthogonal containing minimum amount of cross-information. The EMD successively extracts the IMFs with the highest local frequencies in a recursive way, which yields effectively a set low-pass filters based entirely on the properties exhibited by the data. In this paper, EMD is applied to explore the properties of the multi-year air temperature and to observe its effects on climate change under global warming. This method decomposes the original time-series into intrinsic time scale. It is capable of analyzing nonlinear, non-stationary climatic time series that cause problems to many linear statistical methods and their users. The analysis results show that the mode of EMD presents seasonal variability. The most of the IMFs have normal distribution and the energy density distribution of the IMFs satisfies Chi-square distribution. The IMFs are more effective in isolating physical processes of various time-scales and also statistically significant. The analysis results also show that the EMD method provides a good job to find many characteristics on inter annual climate. The results suggest that climate fluctuations of every single element such as temperature are the results of variations in the global atmospheric circulation.
Abstract: The purpose of the study reported here was designing Information Dissemination System (IDS) based E-learning in agricultural of Iran. A questionnaire was developed to designing Information Dissemination System. The questionnaire was distributed to 96 extension agents who work for Management of Extension and Farming System of Khuzestan province of Iran. Data collected were analyzed using the Statistical Package for the Social Sciences (SPSS). Appropriate statistical procedures for description (frequencies, percent, means, and standard deviations) were used. In this study there was a significant relationship between the age , IT skill and knowledge, years of extension work, the extend of information seeking motivation, level of job satisfaction and level of education with use of information technology by extension agent. According to extension agents five factors were ranked respectively as five top essential items to designing Information Dissemination System (IDS) based E-learning in agricultural of Iran. These factors include: 1) Establish communication between farmers, coordinators (extension agents), agricultural experts, research centers, and community by information technology. 2) The communication between all should be mutual. 3) The information must be based farmers need. 4) Internet used as a facility to transfer the advanced agricultural information to the farming community. 5) Farmers can be illiterate and speak a local and they are not expected to use the system directly. Knowledge produced by the agricultural scientist must be transformed in to computer understandable presentation. To designing Information Dissemination System, electronic communication, in the agricultural society and rural areas must be developed. This communication must be mutual between all factors.
Abstract: This paper deals with a novel approach of power
transformers diagnostics. This approach identifies the exact location
and the range of a fault in the transformer and helps to reduce
operation costs related to handling of the faulty transformer, its
disassembly and repair. The advantage of the approach is a
possibility to simulate healthy transformer and also all faults, which
can occur in transformer during its operation without its
disassembling, which is very expensive in practice. The approach is
based on creating frequency dependent impedance of the transformer
by sweep frequency response analysis measurements and by 3D FE
parametrical modeling of the fault in the transformer. The parameters
of the 3D FE model are the position and the range of the axial short
circuit. Then, by comparing the frequency dependent impedances of
the parametrical models with the measured ones, the location and the
range of the fault is identified. The approach was tested on a real
transformer and showed high coincidence between the real fault and
the simulated one.
Abstract: Cheating on standardized tests has been a major
concern as it potentially minimizes measurement precision. One
major way to reduce cheating by collusion is to administer multiple
forms of a test. Even with this approach, potential collusion is still
quite large. A Latin-square treatment structure for distributing
multiple forms is proposed to further reduce the colluding potential.
An index to measure the extent of colluding potential is also
proposed. Finally, with a simple algorithm, the various Latin-squares
were explored to find the best structure to keep the colluding
potential to a minimum.
Abstract: To study the impact of the inter-module ventilation (IMV) on the space station, the Computational Fluid Dynamic (CFD) model under the influence of IMV, the mathematical model, boundary conditions and calculation method are established and determined to analyze the influence of IMV on cabin air flow characteristics and velocity distribution firstly; and then an integrated overall thermal mathematical model of the space station is used to consider the impact of IMV on thermal management. The results show that: the IMV has a significant influence on the cabin air flow, the flowrate of IMV within a certain range can effectively improve the air velocity distribution in cabin, if too much may lead to its deterioration; IMV can affect the heat deployment of the different modules in space station, thus affecting its thermal management, the use of IMV can effectively maintain the temperature levels of the different modules and help the space station to dissipate the waste heat.
Abstract: Graduate attributes have received increasing attention
over recent years as universities incorporate these attributes into the
curriculum. Graduates who have adequate technical knowledge only
are not sufficiently equipped to compete effectively in the work
place; they also need non disciplinary skills ie, graduate attributes.
The purpose of this paper is to investigate the impact of an eportfolio
in a technical communication course to enhance engineering
students- graduate attributes: namely, learning of communication,
critical thinking and problem solving and teamwork skills. Two
questionnaires were used to elicit information from the students: one
on their preferred and the other on the actual learning process. In
addition, student perceptions of the use of eportfolio as a learning
tool were investigated. Preliminary findings showed that most of the
students- expectations have been met with their actual learning. This
indicated that eportfolio has the potential as a tool to enhance
students- graduate attributes.
Abstract: An Artificial Neural Network based modeling
technique has been used to study the influence of different
combinations of meteorological parameters on evaporation from a
reservoir. The data set used is taken from an earlier reported study.
Several input combination were tried so as to find out the importance
of different input parameters in predicting the evaporation. The
prediction accuracy of Artificial Neural Network has also been
compared with the accuracy of linear regression for predicting
evaporation. The comparison demonstrated superior performance of
Artificial Neural Network over linear regression approach. The
findings of the study also revealed the requirement of all input
parameters considered together, instead of individual parameters
taken one at a time as reported in earlier studies, in predicting the
evaporation. The highest correlation coefficient (0.960) along with
lowest root mean square error (0.865) was obtained with the input
combination of air temperature, wind speed, sunshine hours and
mean relative humidity. A graph between the actual and predicted
values of evaporation suggests that most of the values lie within a
scatter of ±15% with all input parameters. The findings of this study
suggest the usefulness of ANN technique in predicting the
evaporation losses from reservoirs.
Abstract: Article presents the geometry and structure
reconstruction procedure of the aircraft model for flatter research
(based on the I22-IRYDA aircraft). For reconstruction the Reverse
Engineering techniques and advanced surface modeling CAD tools
are used. Authors discuss all stages of data acquisition process,
computation and analysis of measured data. For acquisition the three
dimensional structured light scanner was used. In the further sections,
details of reconstruction process are present. Geometry
reconstruction procedure transform measured input data (points
cloud) into the three dimensional parametric computer model
(NURBS solid model) which is compatible with CAD systems.
Parallel to the geometry of the aircraft, the internal structure
(structural model) are extracted and modeled. In last chapter the
evaluation of obtained models are discussed.
Abstract: The IEEE 802.11e which is an enhanced version of the 802.11 WLAN standards incorporates the Quality of Service (QoS) which makes it a better choice for multimedia and real time applications. In this paper we study various aspects concerned with 802.11e standard. Further, the analysis results for this standard are compared with the legacy 802.11 standard. Simulation results show that IEEE 802.11e out performs legacy IEEE 802.11 in terms of quality of service due to its flow differentiated channel allocation and better queue management architecture. We also propose a method to improve the unfair allocation of bandwidth for downlink and uplink channels by varying the medium access priority level.
Abstract: Collaborative working environments for distance
education can be considered as a more generic form of contemporary
remote labs. At present, the majority of existing real laboratories are
not constructed to allow the involved participants to collaborate in
real time. To make this revolutionary learning environment possible
we must allow the different users to carry out an experiment
simultaneously. In recent times, multi-user environments are
successfully applied in many applications such as air traffic control
systems, team-oriented military systems, chat-text tools, multi-player
games etc. Thus, understanding the ideas and techniques behind these
systems could be of great importance in the contribution of ideas to
our e-learning environment for collaborative working. In this
investigation, collaborative working environments from theoretical
and practical perspectives are considered in order to build an
effective collaborative real laboratory, which allows two students or
more to conduct remote experiments at the same time as a team. In
order to achieve this goal, we have implemented distributed system
architecture, enabling students to obtain an automated help by either
a human tutor or a rule-based e-tutor.
Abstract: We demonstrate single-photon interference over 10 km using a plug and play system for quantum key distribution. The quality of the interferometer is measured by using the interferometer
visibility. The coding of the signal is based on the phase coding and the value of visibility is based on the interference effect, which result a number of count. The setup gives full control of polarization inside
the interferometer. The quality measurement of the interferometer is based on number of count per second and the system produces 94 % visibility in one of the detectors.
Abstract: An ethnobotanical study was conducted to document
local knowledge and potentials of wild edible tubers that has been
reported and sighted and to investigate and record their distribution in
Pulau Redang and nearby islands of Terengganu, Malaysia.
Information was gathered from 42 villagers by using semi-structured
questionnaire. These respondents were selected randomly and no
appointment was made prior to the visits. For distribution, the
locations of wild edible tubers were recorded by using the Global
Positioning System (GPS). The wild edible tubers recorded were ubi
gadung, ubi toyo, ubi kasu, ubi jaga, ubi seratus and ubi kertas.
Dioscorea or commonly known as yam is reported to be one of the
major food sources worldwide. The majority of villagers used
Dioscorea hispida Dennst. or ubi gadung in many ways in their life
such as for food, medicinal purposes and fish poison. The villagers
have identified this ubi gadung by looking at the morphological
characteristics; that include leaf shape, stem and the color of the
tuber-s flesh.
Abstract: Liquidity risk management ranks to key concepts
applied in finance. Liquidity is defined as a capacity to obtain
funding when needed, while liquidity risk means as a threat to this
capacity to generate cash at fair costs. In the paper we present
challenges of liquidity risk management resulting from the 2007-
2009 global financial upheaval. We see five main regulatory
liquidity risk management issues requiring revision in coming
years: liquidity measurement, intra-day and intra-group liquidity
management, contingency planning and liquidity buffers, liquidity
systems, controls and governance, and finally models testing the
viability of business liquidity models.