Abstract: For broadband wireless mobile communication
systems the orthogonal frequency division multiplexing (OFDM) is a
suitable modulation scheme. The frequency offset between
transmitter and receiver local oscillator is main drawback of OFDM
systems, which causes intercarrier interference (ICI) in the
subcarriers of the OFDM system. This ICI degrades the bit error rate
(BER) performance of the system. In this paper an improved self-ICI
cancellation scheme is proposed to improve the system performance.
The proposed scheme is based on discrete Fourier transform-inverse
discrete Fourier transform (DFT-IDFT). The simulation results show
that there is satisfactory improvement in the bit error rate (BER)
performance of the present scheme.
Abstract: The Bangalore City is facing the acute problem of
pollution in the atmosphere due to the heavy increase in the traffic
and developmental activities in recent years. The present study is an
attempt in the direction to assess trend of the ambient air quality
status of three stations, viz., AMCO Batteries Factory, Mysore Road,
GRAPHITE INDIA FACTORY, KHB Industrial Area, Whitefield
and Ananda Rao Circle, Gandhinagar with respect to some of the
major criteria pollutants such as Total Suspended particular matter
(SPM), Oxides of nitrogen (NOx), and Oxides of sulphur (SO2). The
sites are representative of various kinds of growths viz., commercial,
residential and industrial, prevailing in Bangalore, which are
contributing to air pollution. The concentration of Sulphur Dioxide
(SO2) at all locations showed a falling trend due to use of refined
petrol and diesel in the recent years. The concentration of Oxides of
nitrogen (NOx) showed an increasing trend but was within the
permissible limits. The concentration of the Suspended particular
matter (SPM) showed the mixed trend. The correlation between
model and observed values is found to vary from 0.4 to 0.7 for SO2,
0.45 to 0.65 for NOx and 0.4 to 0.6 for SPM. About 80% of data is
observed to fall within the error band of ±50%. Forecast test for the
best fit models showed the same trend as actual values in most of the
cases. However, the deviation observed in few cases could be
attributed to change in quality of petro products, increase in the
volume of traffic, introduction of LPG as fuel in many types of
automobiles, poor condition of roads, prevailing meteorological
conditions, etc.
Abstract: A new conceptual architecture for low-level neural
pattern recognition is presented. The key ideas are that the brain
implements support vector machines and that support vectors are
represented as memory patterns in competitive queuing memories. A
binary classifier is built from two competitive queuing memories
holding positive and negative valence training examples respectively.
The support vector machine classification function is calculated in
synchronized evaluation cycles. The kernel is computed by bisymmetric
feed-forward networks feed by sensory input and by
competitive queuing memories traversing the complete sequence of
support vectors. Temporary summation generates the output
classification. It is speculated that perception apparatus in the brain
reuses structures that have evolved for enabling fluent execution of
prepared action sequences so that pattern recognition is built on
internalized motor programmes.
Abstract: Prime Factorization based on Quantum approach in
two phases has been performed. The first phase has been achieved at
Quantum computer and the second phase has been achieved at the
classic computer (Post Processing). At the second phase the goal is to
estimate the period r of equation xrN ≡ 1 and to find the prime factors
of the composite integer N in classic computer. In this paper we
present a method based on Randomized Approach for estimation the
period r with a satisfactory probability and the composite integer N
will be factorized therefore with the Randomized Approach even the
gesture of the period is not exactly the real period at least we can find
one of the prime factors of composite N. Finally we present some
important points for designing an Emulator for Quantum Computer
Simulation.
Abstract: Tourism and coastal lines are the business sectors
since centuries especially in the European Nations and Albania is one
such spots. However, in recent decades tourism is experienced as
vulnerability of the surrounding ecological conditions of air, soil,
water, land and the communities that are dependant and sharing the
ecosystem among flora and fauna. Experts opine that apart from the
maintenance of near-originality of ecological biodiversity the tourism
rather known as ecotourism an indigenous socio-cultural
maintenance of indigenous/traditional knowledge of the local people
must be well cared in order to sustain on sustainable grounds. As a
general tendency, growth of tourism has been affected by the deterioration in the economic conditions on one aspect and unsustainable ecological areas affected since human interventions
earlier to this has negative impact on futuristic tourist spots. However, tourism in Albania as of now is 11% of GDP and coastal regions accounting to 2-4%. An amicable Mediterranean
climate with 300 sunny days similar parameters of Greece and Spain
throws up sustainable ecotourism in future decades provided public services namely, transportation, road safety, lodging, food
availability, recreational regiments, banking accessibility are as per
the World Tourism Organizations- protocols. Thus as of Albanian
situation, classification of ecotourism activities to safe-guard the localities with its maintenance of ecological land, water and climate
has become a paramount importance with a wanting and satisfactory options through harnessing human energy for profit and fitness of
ecological flora and fauna. A check on anthropogenic wastes and
their safer utilizations inclusive of agricultural and industrial
operations in line with Lalzi Bay Coastal Line are of utmost importance for the reason that the Adriatic Sea Coast is the one long
stretch of Albanian Lifeline. The present work is based on the methodology of the sustainable management of the same issue.
Abstract: This study extends research on the relationship
between marketing strategy and market segmentation by
investigating on market segments in the cement industry.
Competitive strength and rivals distance from the factory were used
as business environment. A three segment (positive, neutral or
indifferent and zero zones) were identified as strategic segments. For
each segment a marketing strategy (aggressive, defensive and
decline) were developed. This study employed data from cement
industry to fulfill two objectives, the first is to give a framework to
the segmentation of cement industry and the second is developing
marketing strategy with varying competitive strength. Fifty six
questionnaires containing close-and open-ended questions were
collected and analyzed. Results supported the theory that segments
tend to be more aggressive than defensive when competitive strength
increases. It is concluded that high strength segments follow total
market coverage, concentric diversification and frontal attack to their
competitors. With decreased competitive strength, Business tends to
follow multi-market strategy, product modification/improvement and
flank attack to direct competitors for this kind of segments. Segments
with weak competitive strength followed focus strategy and decline
strategy.
Abstract: The peng-Robinson (PR), a cubic equation of state (EoS), is extended to polymers by using a single set of energy (A1, A2, A3) and co-volume (b) parameters per polymer fitted to experimental volume data. Excellent results for the volumetric behavior of the 11 polymer up to 2000 bar pressure are obtained. The EoS is applied to the correlation and prediction of Henry constants in polymer solutions comprising three polymer and many nonpolar and polar solvents, including supercritical gases. The correlation achieved with two adjustable parameter is satisfactory compared with the experimental data. As a result, the present work provides a simple and useful model for the prediction of Henry's constant for polymer containing systems including those containing polar, nonpolar and supercritical fluids.
Abstract: In this paper, periodic force operation of a wastewater treatment process has been studied for the improved process performance. A previously developed dynamic model for the process is used to conduct the performance analysis. The static version of the model was utilized first to determine the optimal productivity conditions for the process. Then, feed flow rate in terms of dilution rate i.e. (D) is transformed into sinusoidal function. Nonlinear model predictive control algorithm is utilized to regulate the amplitude and period of the sinusoidal function. The parameters of the feed cyclic functions are determined which resulted in improved productivity than the optimal productivity under steady state conditions. The improvement in productivity is found to be marginal and is satisfactory in substrate conversion compared to that of the optimal condition and to the steady state condition, which corresponds to the average value of the periodic function. Successful results were also obtained in the presence of modeling errors and external disturbances.
Abstract: An actual power plant, which is the power plant of Iron and Steel Factory at Misurata city in Libya , has been modeled using Matlab in order to compare its results to the actual results of the actual cycle. This paper concentrates on two factors:
a- The comparison between exergy losses in the actual cycle and the modeled cycle.
b- The effect of extracting pressure on temperature water at boiler inlet.
Closed heat exchangers used in this plant have been substituted by open heat exchangers in the current study of the modeled power plant and the required changes in the pressure have been considered. In the following investigation the two points mentioned above are taken in consideration.
Abstract: The objective of this study is to investigate fire
behaviors, experimentally and numerically, in a scaled version of an
underground station. The effect of ventilation velocity on the fire is
examined. Fire experiments are simulated by burning 10 ml
isopropyl alcohol fuel in a fire pool with dimensions 5cm x 10cm x 4
mm at the center of 1/100 scaled underground station model. A
commercial CFD program FLUENT was used in numerical
simulations. For air flow simulations, k-ω SST turbulence model and
for combustion simulation, non-premixed combustion model are
used. This study showed that, the ventilation velocity is increased
from 1 m/s to 3 m/s the maximum temperature in the station is found
to be less for ventilation velocity of 1 m/s. The reason for these
experimental result lies on the relative dominance of oxygen supply
effect on cooling effect. Without piston effect, maximum temperature
occurs above the fuel pool. However, when the ventilation velocity
increased the flame was tilted in the direction of ventilation and the
location of maximum temperature moves along the flow direction.
The velocities measured experimentally in the station at different
locations are well matched by the CFD simulation results. The
prediction of general flow pattern is satisfactory with the smoke
visualization tests. The backlayering in velocity is well predicted by
CFD simulation. However, all over the station, the CFD simulations
predicted higher temperatures compared to experimental
measurements.
Abstract: Self-organizing map (SOM) is a well known data
reduction technique used in data mining. It can reveal structure in
data sets through data visualization that is otherwise hard to detect
from raw data alone. However, interpretation through visual
inspection is prone to errors and can be very tedious. There are
several techniques for the automatic detection of clusters of code
vectors found by SOM, but they generally do not take into account
the distribution of code vectors; this may lead to unsatisfactory
clustering and poor definition of cluster boundaries, particularly
where the density of data points is low. In this paper, we propose the
use of an adaptive heuristic particle swarm optimization (PSO)
algorithm for finding cluster boundaries directly from the code
vectors obtained from SOM. The application of our method to
several standard data sets demonstrates its feasibility. PSO algorithm
utilizes a so-called U-matrix of SOM to determine cluster boundaries;
the results of this novel automatic method compare very favorably to
boundary detection through traditional algorithms namely k-means
and hierarchical based approach which are normally used to interpret
the output of SOM.
Abstract: This paper presents the speed regulation scheme of a small brushless dc motor (BLDC motor) with trapezoidal back-emf consideration. The proposed control strategy uses the proportional controller in which the proportional gain, kp, is appropriately adjusted by using genetic algorithms. As a result, the proportional control can perform well in order to compensate the BLDC motor with load disturbance. This confirms that the proposed speed regulation scheme gives satisfactory results.
Abstract: This paper presents a new approach for automatic
document categorization. Exploiting the logical structure of the
document, our approach assigns a HTML document to one or more
categories (thesis, paper, call for papers, email, ...). Using a set of
training documents, our approach generates a set of rules used to
categorize new documents. The approach flexibility is carried out
with rule weight association representing your importance in the
discrimination between possible categories. This weight is
dynamically modified at each new document categorization. The
experimentation of the proposed approach provides satisfactory
results.
Abstract: This paper presents a portable robot that is to use for
welding process in shipbuilding yard. It has six degree of freedom and
3kg payload capability. Its weight is 21.5kg so that human workers can
carry it to the work place. Its body mainly made of magnesium alloy
and aluminum alloy for few parts that require high strength. Since the
distance between robot and controller should be 50m at most, the robot
controller controls the robot through EtherCAT. RTX and KPA are
used for real time EtherCAT control on Windows XP. The
performance of the developed robot was satisfactory, in welding of U
type cell in shipbuilding yard.
Abstract: In the last decades, a number of robust fuzzy clustering algorithms have been proposed to partition data sets affected by noise and outliers. Robust fuzzy C-means (robust-FCM) is certainly one of the most known among these algorithms. In robust-FCM, noise is modeled as a separate cluster and is characterized by a prototype that has a constant distance δ from all data points. Distance δ determines the boundary of the noise cluster and therefore is a critical parameter of the algorithm. Though some approaches have been proposed to automatically determine the most suitable δ for the specific application, up to today an efficient and fully satisfactory solution does not exist. The aim of this paper is to propose a novel method to compute the optimal δ based on the analysis of the distribution of the percentage of objects assigned to the noise cluster in repeated executions of the robust-FCM with decreasing values of δ . The extremely encouraging results obtained on some data sets found in the literature are shown and discussed.
Abstract: Comparison of two approaches for the simulation of
the dynamic behaviour of a permanent magnet linear actuator is
presented. These are full coupled model, where the electromagnetic
field, electric circuit and mechanical motion problems are solved
simultaneously, and decoupled model, where first a set of static
magnetic filed analysis is carried out and then the electric circuit and
mechanical motion equations are solved employing bi-cubic spline
approximations of the field analysis results. The results show that the
proposed decoupled model is of satisfactory accuracy and gives more
flexibility when the actuator response is required to be estimated for
different external conditions, e.g. external circuit parameters or
mechanical loads.
Abstract: Static synchronous compensator (STATCOM) is a shunt connected voltage source converter (VSC), which can affect rapid control of reactive flow in the transmission line by controlling the generated a.c. voltage. The main aim of the paper is to design a power system installed with a Static synchronous compensator (STATCOM) and demonstrates the application of the linearised Phillips-heffron model in analyzing the damping effect of the STATCOM to improve power system oscillation stability. The proposed PI controller is designed to coordinate two control inputs: Voltage of the injection bus and capacitor voltage of the STATCOM, to improve the Dynamic stability of a SMIB system .The power oscillations damping (POD) control and power system stabilizer (PSS) and their coordinated action with proposed controllers are tested. The simulation result shows that the proposed damping controllers provide satisfactory performance in terms of improvements of dynamic stability of the system.
Abstract: This paper gives a novel method for improving
classification performance for cancer classification with very few
microarray Gene expression data. The method employs classification
with individual gene ranking and gene subset ranking. For selection
and classification, the proposed method uses the same classifier. The
method is applied to three publicly available cancer gene expression
datasets from Lymphoma, Liver and Leukaemia datasets. Three
different classifiers namely Support vector machines-one against all
(SVM-OAA), K nearest neighbour (KNN) and Linear Discriminant
analysis (LDA) were tested and the results indicate the improvement
in performance of SVM-OAA classifier with satisfactory results on
all the three datasets when compared with the other two classifiers.
Abstract: In this research saffron samples were prepared from
farms and sampling was done in four states contain : sampling from
fresh saffron of petal with forceps , sampling from fresh saffron of
petal by hands, sampling from dried sample by warm air in shadow,
sampling from dried sample which dried by dryer. Samples collected
and kept in sterile tubes and containers and carried to laboratory and
maintained until experiment. Microbial experiments were performed
to determine microbial load such as total count, Staphylococcus
aureus, coli form, E.coli, mold and yeast. Results showed that in
picking and drying stages the contamination amount increases in
saffron samples. There was a significant difference between the
microbial load of picked up saffron by forceps and by hands, and
also between dried saffron by warm air in shadow and by dryer.
Abstract: Attempts to add fibre and polyphenols (PPs) into
popular beverages present challenges related to the properties of
finished products such as smoothies. Consumer acceptability,
viscosity and phenolic composition of smoothies containing high
levels of fruit fibre (2.5-7.5 g per 300 mL serve) and PPs (250-750
mg per 300 mL serve) were examined. The changes in total
extractable PP, vitamin C content, and colour of selected smoothies
over a storage stability trial (4°C, 14 days) were compared. A set of
acidic aqueous model beverages were prepared to further examine
the effect of two different heat treatments on the stability and
extractability of PPs. Results show that overall consumer
acceptability of high fibre and PP smoothies was low, with average
hedonic scores ranging from 3.9 to 6.4 (on a 1-9 scale). Flavour,
texture and overall acceptability decreased as fibre and polyphenol
contents increased, with fibre content exerting a stronger effect.
Higher fibre content resulted in greater viscosity, with an elevated PP
content increasing viscosity only slightly. The presence of fibre also
aided the stability and extractability of PPs after heating. A reduction
of extractable PPs, vitamin C content and colour intensity of
smoothies was observed after a 14-day storage period at 4°C. Two
heat treatments (75°C for 45 min or 85°C for 1 min) that are
normally used for beverage production, did not cause significant
reduction of total extracted PPs. It is clear that high levels of added
fibre and PPs greatly influence the consumer appeal of smoothies,
suggesting the need to develop novel formulation and processing
methods if a satisfactory functional beverage is to be developed
incorporating these ingredients.