Abstract: This paper proposes the novel model order
formulation scheme to design a discrete PID controller for higher
order linear time invariant discrete systems. Modified PSO (MPSO)
based model order formulation technique has used to obtain the
successful formulated second order system. PID controller is tuned to
meet the desired performance specification by using pole-zero
cancellation and proposed design procedures. Proposed PID
controller is attached with both higher order system and formulated
second order system. System specifications are tabulated and closed
loop response is observed for stabilization process. The proposed
method is illustrated through numerical examples from literature.
Abstract: Over the past decades, automatic face recognition has become a highly active research area, mainly due to the countless application possibilities in both the private as well as the public sector. Numerous algorithms have been proposed in the literature to cope with the problem of face recognition, nevertheless, a group of methods commonly referred to as appearance based have emerged as the dominant solution to the face recognition problem. Many comparative studies concerned with the performance of appearance based methods have already been presented in the literature, not rarely with inconclusive and often with contradictory results. No consent has been reached within the scientific community regarding the relative ranking of the efficiency of appearance based methods for the face recognition task, let alone regarding their susceptibility to appearance changes induced by various environmental factors. To tackle these open issues, this paper assess the performance of the three dominant appearance based methods: principal component analysis, linear discriminant analysis and independent component analysis, and compares them on equal footing (i.e., with the same preprocessing procedure, with optimized parameters for the best possible performance, etc.) in face verification experiments on the publicly available XM2VTS database. In addition to the comparative analysis on the XM2VTS database, ten degraded versions of the database are also employed in the experiments to evaluate the susceptibility of the appearance based methods on various image degradations which can occur in "real-life" operating conditions. Our experimental results suggest that linear discriminant analysis ensures the most consistent verification rates across the tested databases.
Abstract: A property-s selling price is described as the result of
sequential bargaining between a buyer and a seller in an environment
of asymmetric information. Hedonic housing prices are estimated
based upon 17,333 records of New Zealand residential properties
sold during the years 2006 and 2007.
Abstract: The major challenge faced by wireless sensor networks is security. Because of dynamic and collaborative nature of sensor networks the connected sensor devices makes the network unusable. To solve this issue, a trust model is required to find malicious, selfish and compromised insiders by evaluating trust worthiness sensors from the network. It supports the decision making processes in wireless sensor networks such as pre key-distribution, cluster head selection, data aggregation, routing and self reconfiguration of sensor nodes. This paper discussed the kinds of trust model, trust metrics used to address attacks by monitoring certain behavior of network. It describes the major design issues and their countermeasures of building trust model. It also discusses existing trust models used in various decision making process of wireless sensor networks.
Abstract: These All pig-producing countries from around the world report the presence of Postweaning multisystemic wasting syndrome (PMWS.) In America, PCV2 has been recognized in Canada, United States and Brazil. Knowledge concerning the genetic sequences of PMWS has been very important. In Mexico, there is no report describing the genetic sequences and variations of the PCV2 virus present around the country. For this reason, the main objective was to describe the homology and genetic sequences of the PCV2 virus obtained from different regions of Mexico. The results show that in Mexico are present both subgenotypes \"a\" and \"b\" of this virus and the homologies are from 89 to 99%. Regarding with the aminoacid sequence, three major heterogenic regions were present in the position 59-91, 123–136 and 185–210. This study presents the results of the first genetic characterization of PCV2 in production herds from Mexico.
Abstract: In this paper, we proposed the direct method for converting
Finite-Impulse Response (FIR) filter with low nonzero tap
into Infinite-Impulse Response (IIR) filter using the pre-determined
table. The prony method is used by ghost cancellator which is IIR
approximation to FIR filter which is better performance than IIR and
have much larger calculation difference. The direct method for many
ghost combination with low nonzero tap of NTSC(National Television
System Committee) TV signal in Korea is described. The proposed
method is illustrated with an example.
Abstract: The application of agro-industrial waste in Aluminum
Metal Matrix Composites has been getting more attention as they
can reinforce particles in metal matrix which enhance the strength
properties of the composites. In addition, by applying these agroindustrial
wastes in useful way not only save the manufacturing cost
of products but also reduce the pollutions on environment. This
paper represents a literature review on a range of industrial wastes
and their utilization in metal matrix composites. The paper describes
the synthesis methods of agro-industrial waste filled metal matrix
composite materials and their mechanical, wear, corrosion, and
physical properties. It also highlights the current application and
future potential of agro-industrial waste reinforced composites in
aerospace, automotive and other construction industries.
Abstract: This paper proposes two types of non-isolated
direct AC-DC converters. First, it shows a buck-boost
converter with an H-bridge, which requires few components
(three switches, two diodes, one inductor and one capacitor) to
convert AC input to DC output directly. This circuit can handle
a wide range of output voltage. Second, a direct AC-DC buck
converter is proposed for lower output voltage applications.
This circuit is analyzed with output voltage of 12V. We
describe circuit topologies, operation principles and simulation
results for both circuits.
Abstract: A kind of singularly perturbed boundary value problems is under consideration. In order to obtain its approximation, simple upwind difference discretization is applied. We use a moving mesh iterative algorithm based on equi-distributing of the arc-length function of the current computed piecewise linear solution. First, a maximum norm a posteriori error estimate on an arbitrary mesh is derived using a different method from the one carried out by Chen [Advances in Computational Mathematics, 24(1-4) (2006), 197-212.]. Then, basing on the properties of discrete Green-s function and the presented posteriori error estimate, we theoretically prove that the discrete solutions computed by the algorithm are first-order uniformly convergent with respect to the perturbation parameter ε.
Abstract: A model of user behaviour based automated planning
is introduced in this work. The behaviour of users of web interactive
systems can be described in term of a planning domain encapsulating
the timed actions patterns representing the intended user profile. The
user behaviour recognition is then posed as a planning problem
where the goal is to parse a given sequence of user logs of the
observed activities while reaching a final state.
A general technique for transforming a timed finite state automata
description of the behaviour into a numerical parameter planning
model is introduced.
Experimental results show that the performance of a planning
based behaviour model is effective and scalable for real world
applications. A major advantage of the planning based approach is to
represent in a single automated reasoning framework problems of
plan recognitions, plan synthesis and plan optimisation.
Abstract: Most buildings have been using anchor bolts
commonly for installing outdoor advertising structures. Anchor bolts
of common carbon steel are widely used and often installed
indiscriminately by inadequate installation standards. In the area
where strong winds frequently blow, falling accidents of outdoor
advertising structures can occur and cause a serious disaster, which is
very dangerous and to be prevented. In this regard, the development of
high-performance anchor bolts is urgently required. In the present
study, 25Cr-8Ni-1.5Si-1Mn-0.4C alloy was produced by traditional
vacuum induction melting (VIM) for the application of anchor bolt.
The alloy composition is revealed as a duplex microstructure from
thermodynamic phase analysis by FactSage® and confirmed by
metallographic experiment. Addition of Nitrogen to the alloy was
found to reduce the ferritic phase domain and significantly increase the
hardness and the tensile strength. Microstructure observation revealed
mixed structure of austenite and ferrite with fine carbide distributed
along the grain and phase boundaries.
Abstract: In this work, simulation algorithms for contact drying
of agitated particulate materials under vacuum and at atmospheric
pressure were developed. The implementation of algorithms gives a
predictive estimation of drying rate curves and bulk bed temperature
during contact drying. The calculations are based on the penetration
model to describe the drying process, where all process parameters
such as heat and mass transfer coefficients, effective bed properties,
gas and liquid phase properties are estimated with proper
correlations. Simulation results were compared with experimental
data from the literature. In both cases, simulation results were in good
agreement with experimental data. Few deviations were identified
and the limitations of the predictive capabilities of the models are
discussed. The programs give a good insight of the drying behaviour
of the analysed powders.
Abstract: This article analyses conspiracy theories as part of the
wider discourses of missionary politics. It presents a case study of
Venezuela and describes how its leaders use conspiracy theories as
political tools. Through quotes taken form Venezuelan president
Chavez-s public speeches and other sources, and through a short
analysis of the ideological basis of his discourses, it shows how
conspiracy theories are constructed and how they affect the local
political praxis. The article also describes how conspiracy theories
have been consistently used as an important part of the construction of
a political religion for the New Man of the Bolivarian Revolution. It
concludes that the use of conspiracy theories by political leaders
produces a sense of loss of political agency.
Abstract: This paper will first describe predictor controllers
when the proportional-integral-derivative (PID) controllers are
inactive for procedures that have large delay time (LDT) in transfer
stage. Therefore in those states, the predictor controllers are better
than the PID controllers, then compares three types of predictor
controllers. The value of these controller-s parameters are obtained
by trial and error method, so here an effort has been made to obtain
these parameters by Ziegler-Nichols method. Eventually in this paper
Ziegler-Nichols method has been described and finally, a PIP
controller has been designed for a thermal system, which circulates
hot air to keep the temperature of a chamber constant.
Abstract: The aim of this study is to examine the reading
comprehension scores of Turkish 5th grade students according to the
variables given in the student questionnaire. In this descriptive
survey study research participated 279 5th grade students, who
studied at 10 different primary schools in four provinces of Ankara in
2008-2009 academic year. Two different data collection tools were
made use of in the study: “Reading Comprehension Test" and
“Student Information Questionnaire". Independent sample t-test, oneway
Anova and two-way Anova tests were used in the analyses of
the gathered data. The results of the study indicate that the reading
comprehension scores of the students differ significantly according to
sex of the students, the number of books in their houses, the
frequency of summarizing activities on the reading text of free and
the frequency reading hours provided by their teachers; but, differ
not significantly according to educational level of their mothers and
fathers.
Abstract: This paper is a part of research, in which the way the
biomedical engineers follow in their work is analyzed. The goal of
this paper is to present a method for specification of user
requirements in the medical devices maintenance process. Data
Gathering Methods, Research Model Phases and Descriptive
Analysis is presented. These technology and verification rules can be
implemented in Medical devices maintenance management process to
the maintenance process.
Abstract: Droplet size distributions in the cold spray of a fuel
are important in observed combustion behavior. Specification of
droplet size and velocity distributions in the immediate downstream
of injectors is also essential as boundary conditions for advanced
computational fluid dynamics (CFD) and two-phase spray transport
calculations. This paper describes the development of a new model to
be incorporated into maximum entropy principle (MEP) formalism
for prediction of droplet size distribution in droplet formation region.
The MEP approach can predict the most likely droplet size and
velocity distributions under a set of constraints expressing the
available information related to the distribution.
In this article, by considering the mechanisms of turbulence
generation inside the nozzle and wave growth on jet surface, it is
attempted to provide a logical framework coupling the flow inside the
nozzle to the resulting atomization process. The purpose of this paper
is to describe the formulation of this new model and to incorporate it
into the maximum entropy principle (MEP) by coupling sub-models
together using source terms of momentum and energy. Comparison
between the model prediction and experimental data for a gas turbine
swirling nozzle and an annular spray indicate good agreement
between model and experiment.
Abstract: The importance of good requirements engineering is well documented. Agile practices, promoting collaboration and communications, facilitate the elicitation and management of volatile requirements. However, current Agile practices work in a well-defined environment. It is necessary to have a co-located customer. With distributed development it is not always possible to realize this co-location. In this environment a suitable process, possibly supported by tools, is required to support changing requirements. This paper introduces the issues of concern when managing requirements in a distributed environment and describes work done at the Software Technology Research Centre as part of the NOMAD project.
Abstract: This study aims to segment objects using the K-means
algorithm for texture features. Firstly, the algorithm transforms color
images into gray images. This paper describes a novel technique for
the extraction of texture features in an image. Then, in a group of
similar features, objects and backgrounds are differentiated by using
the K-means algorithm. Finally, this paper proposes a new object
segmentation algorithm using the morphological technique. The
experiments described include the segmentation of single and multiple
objects featured in this paper. The region of an object can be
accurately segmented out. The results can help to perform image
retrieval and analyze features of an object, as are shown in this paper.
Abstract: This article presents the developments of efficient
algorithms for tablet copies comparison. Image recognition has
specialized use in digital systems such as medical imaging,
computer vision, defense, communication etc. Comparison between
two images that look indistinguishable is a formidable task. Two
images taken from different sources might look identical but due to
different digitizing properties they are not. Whereas small variation
in image information such as cropping, rotation, and slight
photometric alteration are unsuitable for based matching
techniques. In this paper we introduce different matching
algorithms designed to facilitate, for art centers, identifying real
painting images from fake ones. Different vision algorithms for
local image features are implemented using MATLAB. In this
framework a Table Comparison Computer Tool “TCCT" is
designed to facilitate our research. The TCCT is a Graphical Unit
Interface (GUI) tool used to identify images by its shapes and
objects. Parameter of vision system is fully accessible to user
through this graphical unit interface. And then for matching, it
applies different description technique that can identify exact
figures of objects.