Abstract: Stirred tanks have applications in many chemical
processes where mixing is important for the overall performance of
the system. In present work 5%v of the tank is filled by solid particles
with diameter of 700 m that Rushton Turbine and Propeller impeller
is used for stirring. An Eulerian-Eulerian Multi Fluid Model coupled
and for modeling rotating of impeller, moving reference frame
(MRF) technique was used and standard-k- model was selected for
turbulency. Flow field, radial velocity and axial distribution of solid
for both of impellers was investigation and comparison. Comparisons
of simulation results between Rushton Turbine and propeller impeller
shows that final quality of solid-liquid slurry in different rotating
speed for propeller impeller is better than the Rushton Turbine.
Abstract: In the present paper, a set of parametric FE stress
analyses is carried out for two-planar welded tubular DKT-joints
under two different axial load cases. Analysis results are used to
present general remarks on the effect of geometrical parameters on
the stress concentration factors (SCFs) at the inner saddle, outer
saddle, toe, and heel positions on the main (outer) brace. Then a new
set of SCF parametric equations is developed through nonlinear
regression analysis for the fatigue design of two-planar DKT-joints.
An assessment study of these equations is conducted against the
experimental data; and the satisfaction of the criteria regarding the
acceptance of parametric equations is checked. Significant effort has
been devoted by researchers to the study of SCFs in various uniplanar
tubular connections. Nevertheless, for multi-planar joints
covering the majority of practical applications, very few
investigations have been reported due to the complexity and high
cost involved.
Abstract: The effect of the number of quantum dot (QD) layers
on the saturated gain of doped QD semiconductor optical amplifiers
(SOAs) has been studied using multi-population coupled rate
equations. The developed model takes into account the effect of
carrier coupling between adjacent layers. It has been found that
increasing the number of QD layers (K) increases the unsaturated
optical gain for K
Abstract: Behavior of turbulent jet is relying on jet parameters,
environmental and geometric parameters. In this research, it has
attempt to Study effect of jet parameters of internal angle on
maximum effective length and velocity on centerline from nozzle
experimentally. Toward this end, four internal angles 30, 45, 60 and
90-degree are considered for this study in a flume with 600cm as
long, 100cm as high and 150cm in width. Various discharges were
used to evaluate effective length for a wide range of densimetric
Froude numbers F0, from 17.9 to 39.4 that is defined at the nozzle. As
a result, It is revealed that both velocity on centerline and effective
length decreases when nozzle angle decreased from 90° to 30°. The
results show that, for all range of Fr0 the Um/U0 ratio for nozzle with
α=90° on centerline increases 20% - 27% than nozzle with α=30° that
has lowest velocity on centerline than other nozzle.
Abstract: Hexapod Machine Tool (HMT) is a parallel robot
mostly based on Stewart platform. Identification of kinematic
parameters of HMT is an important step of calibration procedure. In
this paper an algorithm is presented for identifying the kinematic
parameters of HMT using inverse kinematics error model. Based on
this algorithm, the calibration procedure is simulated. Measurement
configurations with maximum observability are decided as the first
step of this algorithm for a robust calibration. The errors occurring in
various configurations are illustrated graphically. It has been shown
that the boundaries of the workspace should be searched for the
maximum observability of errors. The importance of using
configurations with sufficient observability in calibrating hexapod
machine tools is verified by trial calibration with two different
groups of randomly selected configurations. One group is selected to
have sufficient observability and the other is in disregard of the
observability criterion. Simulation results confirm the validity of the
proposed identification algorithm.
Abstract: Conception is the primordial part in the realization of
a computer system. Several tools have been used to help inventors to
describe their software. These tools knew a big success in the
relational databases domain since they permit to generate SQL script
modeling the database from an Entity/Association model. However,
with the evolution of the computer domain, the relational databases
proved their limits and object-relational model became used more
and more. Tools of present conception don't support all new concepts
introduced by this model and the syntax of the SQL3 language. We
propose in this paper a tool of help to the conception and
implementation of object-relational databases called «NAVIGTOOLS"
that allows the user to generate script modeling its database
in SQL3 language. This tool bases itself on the Entity/Association
and navigational model for modeling the object-relational databases.
Abstract: Diatoms are an important group of aquatic ecosystems and diatom-based indices are increasingly becoming important tools for the assessment of ecological conditions in lotic systems. Although the studies are very limited about Turkish rivers, diatom indices were used for monitoring rivers in different basins. In the present study, we used OMNIDIA program for estimation of stream quality. Some indices have less sensitive (IDP, WAT, LOBO, GENRE, TID, CEE, PT), intermediate sensitivities (IDSE, DESCY, IPS, DI-CH, SLA, IDAP), the others higher sensitivities (SID, IBD, SHE, EPI-D). Among the investigated diatom communities, only a few taxa indicated alfa-mesosaprobity and polysaprobity. Most of the sites were characterized by a great relative contribution of eutraphent and tolerant ones as well as oligosaprobic and betamesosaprobic diatoms. In general, SID and IBD indices gave the best results. This study suggests that the structure of benthic diatom communities and diatom indices, especially SID, can be applied for monitoring rivers in Southern Turkey.
Abstract: Rotating stages in semiconductor, display industry and many other fields require challenging accuracy to perform their functions properly. Especially, Axis of rotation error on rotary system is significant; such as the spindle error motion of the aligner, wire bonder and inspector machine which result in the poor state of manufactured goods. To evaluate and improve the performance of such precision rotary stage, unessential movements on the other 5 degrees of freedom of the rotary stage must be measured and analyzed. In this paper, we have measured the three translations and two tilt motions of a rotating stage with high precision capacitive sensors. To obtain the radial error motion from T.I.R (Total Indicated Reading) of radial direction, we have used Donaldson's reversal technique. And the axial components of the spindle tilt error motion can be obtained accurately from the axial direction outputs of sensors by Estler face motion reversal technique. Further more we have defined and measured the sensitivity of positioning error to the five error motions.
Abstract: This study is to investigate the electroencephalogram (EEG) differences generated from a normal and Alzheimer-s disease (AD) sources. We also investigate the effects of brain tissue distortions due to AD on EEG. We develop a realistic head model from T1 weighted magnetic resonance imaging (MRI) using finite element method (FEM) for normal source (somatosensory cortex (SC) in parietal lobe) and AD sources (right amygdala (RA) and left amygdala (LA) in medial temporal lobe). Then, we compare the AD sourced EEGs to the SC sourced EEG for studying the nature of potential changes due to sources and 5% to 20% brain tissue distortions. We find an average of 0.15 magnification errors produced by AD sourced EEGs. Different brain tissue distortion models also generate the maximum 0.07 magnification. EEGs obtained from AD sources and different brain tissue distortion levels vary scalp potentials from normal source, and the electrodes residing in parietal and temporal lobes are more sensitive than other electrodes for AD sourced EEG.
Abstract: In this paper, growth and collapse of a vapour bubble
generated due to a local energy input inside a rigid cylinder and in
the absence of buoyancy forces is investigated using Boundary
Integral Equation Method and Finite Difference Method .The fluid is
treated as potential flow and Boundary Integral Equation Method is
used to solve Laplace-s equation for velocity potential. Different
ratios of the diameter of the rigid cylinder to the maximum radius of
the bubble are considered. Results show that during the collapse
phase of the bubble inside a vertical rigid cylinder, two liquid micro
jets are developed on the top and bottom sides of the vapour bubble
and are directed inward. It is found that by increasing the ratio of the
cylinder diameter to the maximum radius of the bubble, the rate of
the growth and collapse phases of the bubble increases and the life
time of the bubble decreases.
Abstract: The purpose of the present study is to analyze the
effect of the target plate-s curvature on the heat transfer in laminar
confined impinging jet flows. Numerical results from two
dimensional compressible finite volume solver are compared
between three different shapes of impinging plates: Flat, Concave
and Convex plates. The remarkable result of this study proves that
the stagnation Nusselt number in laminar range of Reynolds number
based on the slot width is maximum in convex surface and is
minimum in concave plate. These results refuse the previous data in
literature stating the amount of the stagnation Nusselt number is
greater in concave surface related to flat plate configuration.
Abstract: In the past decade, the development of microstrip
sensor application has evolved tremendously. Although cut and trial
method was adopted to develop microstrip sensing applications in the
past, Computer-Aided-Design (CAD) is a more effective as it ensures
less time is consumed and cost saving is achieved in developing
microstrip sensing applications. Therefore microstrip sensing
applications has gained popularity as an effective tool adopted in
continuous sensing of moisture content particularly in products that is
administered mainly by liquid content. In this research, the Cole-Cole
representation of reactive relaxation is applied to assess the
performance of the microstrip sensor devices. The microstrip sensor
application is an effective tool suitable for sensing the moisture
content of dielectric material. Analogous to dielectric relaxation
consideration of Cole-Cole diagrams as applied to dielectric
materials, a “reactive relaxation concept” concept is introduced to
represent the frequency-dependent and moisture content
characteristics of microstrip sensor devices.
Abstract: This paper presents the study of induced currents and
temperature distribution in gear heated by induction process using 2D
finite element (FE) model. The model is developed by coupling
Maxwell and heat transfer equations into a multi-physics model. The
obtained results allow comparing the medium frequency (MF) and
high frequency (HF) cases and the effect of machine parameters on
the evolution of induced currents and temperature during heating.
The sensitivity study of the temperature profile is conducted and the
case hardness is predicted using the final temperature profile. These
results are validated using tests and give a good understanding of
phenomena during heating process.
Abstract: The motorway segment between Tangier and Oued
R’mel has experienced, since the beginning of building works,
significant instability and landslides linked to a number of geological,
hydrogeological and geothermic factors affecting the different
formations.
The landslides observed are not fully understood, despite many
studies conducted on this segment. This study aims at producing new
methods to better explain the phenomena behind the landslides,
taking into account the geotechnical and geothermic contexts. This
analysis builds up on previous studies and geotechnical data collected
in the field.
The final body of data collected shall be processed through the
Plaxis software for a better and customizable view of the landslide
problems in the area, which will help tofind solutions and stabilize
land in the area.
Abstract: In this paper, we were introduces a skin detection
method using a histogram approximation based on the mean shift
algorithm. The proposed method applies the mean shift procedure to a
histogram of a skin map of the input image, generated by comparison
with standard skin colors in the CbCr color space, and divides the
background from the skin region by selecting the maximum value
according to brightness level. The proposed method detects the skin
region using the mean shift procedure to determine a maximum value
that becomes the dividing point, rather than using a manually selected
threshold value, as in existing techniques. Even when skin color is
contaminated by illumination, the procedure can accurately segment
the skin region and the background region. The proposed method may
be useful in detecting facial regions as a pretreatment for face
recognition in various types of illumination.
Abstract: Climate change leading to global warming affects the
earth through many different ways such as weather (temperature, precipitation, humidity and the other parameters of weather), snow coverage and ice melting, sea level rise, hydrological cycles, quality of water, agriculture, forests, ecosystems and health. One of the most
affected areas by climate change is hydrology and water resources.
Regions where majority of runoff consists of snow melt are more
sensitive to climate change. The first step of climate change studies
is to establish trends of significant climate variables including precipitation,
temperature and flow data to detect any potential climate
change impacts already happened. Two popular non-parametric trend
analysis methods, Mann-Kendal and Spearman-s Rho were applied
to Upper Euphrates Basin (Turkey) to detect trends of precipitation,
temperatures (maximum, minimum and average) and streamflow.
Abstract: A suspension bridge is the most suitable type of structure for a long-span bridge due to rational use of structural materials. Increased deformability, which is conditioned by appearance of the elastic and kinematic displacements, is the major disadvantage of suspension bridges. The problem of increased kinematic displacements under the action of non-symmetrical load can be solved by prestressing. The prestressed suspension bridge with the span of 200 m was considered as an object of investigations. The cable truss with the cross web was considered as the main load carrying structure of the prestressed suspension bridge. The considered cable truss was optimized by 47 variable factors using Genetic algorithm and FEM program ANSYS. It was stated, that the maximum total displacements are reduced up to 29.9% by using of the cable truss with the rational characteristics instead of the single cable in the case of the worst situated load.
Abstract: This paper deals with a novel approach of power
transformers diagnostics. This approach identifies the exact location
and the range of a fault in the transformer and helps to reduce
operation costs related to handling of the faulty transformer, its
disassembly and repair. The advantage of the approach is a
possibility to simulate healthy transformer and also all faults, which
can occur in transformer during its operation without its
disassembling, which is very expensive in practice. The approach is
based on creating frequency dependent impedance of the transformer
by sweep frequency response analysis measurements and by 3D FE
parametrical modeling of the fault in the transformer. The parameters
of the 3D FE model are the position and the range of the axial short
circuit. Then, by comparing the frequency dependent impedances of
the parametrical models with the measured ones, the location and the
range of the fault is identified. The approach was tested on a real
transformer and showed high coincidence between the real fault and
the simulated one.
Abstract: A co-generation system in automobile can improve
thermal efficiency of vehicle in some degree. The waste heat from the
engine exhaust and coolant is still attractive energy source that reaches
around 60% of the total energy converted from fuel. To maximize the
effectiveness of heat exchangers for recovering the waste heat, it is
vital to select the most suitable working fluid for the system, not to
mention that it is important to find the optimum design for the heat
exchangers. The design of heat exchanger is out of scoop of this study;
rather, the main focus has been on the right selection of working fluid
for the co-generation system. Simulation study was carried out to find
the most suitable working fluid that can allow the system to achieve
the optimum efficiency in terms of the heat recovery rate and thermal
efficiency.
Abstract: In April 2009, a new variant of Influenza A virus
subtype H1N1 emerged in Mexico and spread all over the world. The
influenza has three subtypes in human (H1N1, H1N2 and H3N2)
Types B and C influenza tend to be associated with local or regional
epidemics. Preliminary genetic characterization of the influenza
viruses has identified them as swine influenza A (H1N1) viruses.
Nucleotide sequence analysis of the Haemagglutinin (HA) and
Neuraminidase (NA) are similar to each other and the majority of
their genes of swine influenza viruses, two genes coding for the
neuraminidase (NA) and matrix (M) proteins are similar to
corresponding genes of swine influenza. Sequence similarity between
the 2009 A (H1N1) virus and its nearest relatives indicates that its
gene segments have been circulating undetected for an extended
period. Nucleic acid sequence Maximum Likelihood (MCL) and
DNA Empirical base frequencies, Phylogenetic relationship amongst
the HA genes of H1N1 virus isolated in Genbank having high
nucleotide sequence homology.
In this paper we used 16 HA nucleotide sequences from NCBI for
computing sequence relationships similarity of swine influenza A
virus using the following method MCL the result is 28%, 36.64% for
Optimal tree with the sum of branch length, 35.62% for Interior
branch phylogeny Neighber – Join Tree, 1.85% for the overall
transition/transversion, and 8.28% for Overall mean distance.