Abstract: In two studies we tested the hypothesis that the
appropriate linguistic formulation of a deontic rule – i.e. the
formulation which clarifies the monadic nature of deontic operators
- should produce more correct responses than the conditional
formulation in Wason selection task. We tested this assumption by
presenting a prescription rule and a prohibition rule in conditional
vs. proper deontic formulation. We contrasted this hypothesis with
two other hypotheses derived from social contract theory and
relevance theory. According to the first theory, a deontic rule
expressed in terms of cost-benefit should elicit a cheater detection
module, sensible to mental states attributions and thus able to
discriminate intentional rule violations from accidental rule
violations. We tested this prevision by distinguishing the two types
of violations. According to relevance theory, performance in
selection task should improve by increasing cognitive effect and
decreasing cognitive effort. We tested this prevision by focusing
experimental instructions on the rule vs. the action covered by the
rule. In study 1, in which 480 undergraduates participated, we
tested these predictions through a 2 x 2 x 2 x 2 (type of the rule x
rule formulation x type of violation x experimental instructions)
between-subjects design. In study 2 – carried out by means of a 2 x
2 (rule formulation x type of violation) between-subjects design -
we retested the hypothesis of rule formulation vs. the cheaterdetection
hypothesis through a new version of selection task in
which intentional vs. accidental rule violations were better
discriminated. 240 undergraduates participated in this study.
Results corroborate our hypothesis and challenge the contrasting
assumptions. However, they show that the conditional formulation
of deontic rules produces a lower performance than what is
reported in literature.
Abstract: Speed sensorless systems are intensively studied during recent years; this is mainly due to their economical benefit and fragility of mechanical sensors and also the difficulty of installing this type of sensor in many applications. These systems suffer from instability problems and sensitivity to parameter mismatch at low speed operation. In this paper an analysis of adaptive observer stability with stator resistance estimation is given.
Abstract: In this paper, an analytical approach for free vibration
analysis of four edges simply supported rectangular Kirchhoff plates
is presented. The method is based on wave approach. From wave
standpoint vibration propagate, reflect and transmit in a structure.
Firstly, the propagation and reflection matrices for plate with simply
supported boundary condition are derived. Then, these matrices are
combined to provide a concise and systematic approach to free
vibration analysis of a simply supported rectangular Kirchhoff plate.
Subsequently, the eigenvalue problem for free vibration of plates is
formulated and the equation of plate natural frequencies is
constructed. Finally, the effectiveness of the approach is shown by
comparison of the results with existing classical solution.
Abstract: Data stream analysis is the process of computing
various summaries and derived values from large amounts of data
which are continuously generated at a rapid rate. The nature of a
stream does not allow a revisit on each data element. Furthermore,
data processing must be fast to produce timely analysis results. These
requirements impose constraints on the design of the algorithms to
balance correctness against timely responses. Several techniques
have been proposed over the past few years to address these
challenges. These techniques can be categorized as either dataoriented
or task-oriented. The data-oriented approach analyzes a
subset of data or a smaller transformed representation, whereas taskoriented
scheme solves the problem directly via approximation
techniques. We propose a hybrid approach to tackle the data stream
analysis problem. The data stream has been both statistically
transformed to a smaller size and computationally approximated its
characteristics. We adopt a Monte Carlo method in the approximation
step. The data reduction has been performed horizontally and
vertically through our EMR sampling method. The proposed method
is analyzed by a series of experiments. We apply our algorithm on
clustering and classification tasks to evaluate the utility of our
approach.
Abstract: In this paper, based on the coupled-mode and carrier rate equations, derivation of a dynamic model and numerically analysis of a MQW chirped DFB-SOA all-optical flip-flop is done precisely. We have analyzed the effects of strains of QW and MQW and cross phase modulation (XPM) on the dynamic response, and rise and fall times of the DFB-SOA all optical flip flop. We have shown that strained MQW active region in under an optimized condition into a DFB-SOA with chirped grating can improve the switching ON speed limitation in such a of the device, significantly while the fall time is increased. The values of the rise times for such an all optical flip-flop, are obtained in an optimized condition, areas tr=255ps.
Abstract: In this paper the vibration behaviors of a structure equipped with a tuned liquid column damper (TLCD) under a harmonic type of earthquake loading are studied. However, due to inherent nonlinear liquid damping, it is no doubt that a great deal of computational effort is required to search the optimum parameters of the TLCD, numerically. Therefore by linearization the equation of motion of the single degree of freedom structure equipped with the TLCD, the closed form solutions of the TLCD-structure system are derived. To find the reliability of the analytical method, the results have been compared with other researcher and have good agreement. Further, the effects of optimal design parameters such as length ratio and mass ratio on the performance of the TLCD for controlling the responses of a structure are investigated by using the harmonic type of earthquake excitation. Finally, the Citicorp Center which has a very flexible structure is used as an example to illustrate the design procedure for the TLCD under the earthquake excitation.
Abstract: In this paper, the modelling and design of artificial neural network architecture for load forecasting purposes is investigated. The primary pre-requisite for power system planning is to arrive at realistic estimates of future demand of power, which is known as Load Forecasting. Short Term Load Forecasting (STLF) helps in determining the economic, reliable and secure operating strategies for power system. The dependence of load on several factors makes the load forecasting a very challenging job. An over estimation of the load may cause premature investment and unnecessary blocking of the capital where as under estimation of load may result in shortage of equipment and circuits. It is always better to plan the system for the load slightly higher than expected one so that no exigency may arise. In this paper, a load-forecasting model is proposed using a multilayer neural network with an appropriately modified back propagation learning algorithm. Once the neural network model is designed and trained, it can forecast the load of the power system 24 hours ahead on daily basis and can also forecast the cumulative load on daily basis. The real load data that is used for the Artificial Neural Network training was taken from LDC, Gujarat Electricity Board, Jambuva, Gujarat, India. The results show that the load forecasting of the ANN model follows the actual load pattern more accurately throughout the forecasted period.
Abstract: The inability to implement the principles of good
corporate governance (GCG) as demonstrated in the surveys is due to
a number of constraints which can be classified into three; namely internal constraints, external constraints, and constraints coming
from the structure of ownership. The issues in the internal constraints
mentioned are related to the function of several elements of the company. As a business organization, corporation is unable to
achieve its goal to successfully implement GCG principles since it is
not support by its internal elements- functions. Two of several numbers of internal elements of a company are ethical work climate
and leadership style of the top management.
To prove the correlation between internal function of organization
(in this case ethical work climate and transformational leadership)
and the successful implementation of GCG principles, this study
proposes two hypotheses to be empirically tested on thirty surveyed organizations; eleven of which are state-owned companies and
nineteen are private companies. These thirty corporations are listed in
the Jakarta Stock Exchange. All state-owned companies in the
samples are those which have been privatized.
The research showed that internal function of organization give
support to the successful implementation of GCG principle. In this
research we can prove that : (i) ethical work climate has positive
significance of correlation with the successful implementation of
social awareness principle (one of principles on GCG) and, (ii) only
at the state-owned companies, transformational leadership have
positive significance effect to forming the ethical work climate.
Abstract: The control of commutation of switched reluctance
(SR) motor has nominally depended on a physical position detector.
The physical rotor position sensor limits robustness and increases
size and inertia of the SR drive system. The paper describes a method
to overcome these limitations by using magnetization characteristics
of the motor to indicate rotor and stator teeth overlap status. The
method is using active current probing pulses of same magnitude that
is used to simulate flux linkage in the winding being probed. A
microprocessor is used for processing magnetization data to deduce
rotor-stator teeth overlap status and hence rotor position. However,
the back-of-core saturation and mutual coupling introduces overlap
detection errors, hence that of commutation control. This paper
presents the concept of the detection scheme and the effects of backof
core saturation.
Abstract: This paper introduces a hardware solution to password
exposure problem caused by direct accesses to the keyboard hardware
interfaces through which a possible attacker is able to grab user-s
password even where existing countermeasures are deployed. Several
researches have proposed reasonable software based solutions to the
problem for years. However, recently introduced hardware
vulnerability problems have neutralized the software approaches and
yet proposed any effective software solution to the vulnerability.
Hardware approach in this paper is expected as the only solution to the
vulnerability
Abstract: In this paper, a double balanced radio frequency multiplier
is presented which is customized for transmitted reference
ultra wideband (UWB) receivers. The multiplier uses 90nm model
parameters and exploits compensating transistors to provide controllable
gain for a Gilbert core. After performing periodic and quasiperiodic
non linear analyses the RF mixer (multiplier) achieves a
voltage conversion gain of 16 dB and a DSB noise figure of 8.253
dB with very low power consumption. A high degree of LO to RF
isolation (in the range of -94dB), RF to IF isolation (in the range of
-95dB) and LO to IF isolation (in the range of -143dB) is expected
for this design with an input-referred IP3 point of -1.93 dBm and an
input referred 1 dB compression point of -10.67dBm. The amount of
noise at the output is 7.7 nV/√Hz when the LO input is driven by
a 10dBm signal. The mixer manifests better results when compared
with other reported multiplier circuits and its Zero-IF performance
ensures its applicability as TR-UWB multipliers.
Abstract: Majority of Business Software Systems (BSS)
Development and Enhancement Projects (D&EP) fail to meet criteria
of their effectiveness, what leads to the considerable financial losses.
One of the fundamental reasons for such projects- exceptionally low
success rate are improperly derived estimates for their costs and time.
In the case of BSS D&EP these attributes are determined by the work
effort, meanwhile reliable and objective effort estimation still appears
to be a great challenge to the software engineering. Thus this paper is
aimed at presenting the most important synthetic conclusions coming
from the author-s own studies concerning the main factors of
effective BSS D&EP work effort estimation. Thanks to the rational
investment decisions made on the basis of reliable and objective
criteria it is possible to reduce losses caused not only by abandoned
projects but also by large scale of overrunning the time and costs of
BSS D&EP execution.
Abstract: In this paper, we present a framework to determine Haar solutions of Bratu-type equations that are widely applicable in fuel ignition of the combustion theory and heat transfer. The method is proposed by applying Haar series for the highest derivatives and integrate the series. Several examples are given to confirm the efficiency and the accuracy of the proposed algorithm. The results show that the proposed way is quite reasonable when compared to exact solution.
Abstract: The state of melt viscosity in injection process is significantly influenced by the setting parameters due to that the shear rate of injection process is higher than other processes. How to determine plastic melt viscosity during injection process is important to understand the influence of setting parameters on the melt viscosity. An apparatus named as pressure sensor bushing (PSB) module that is used to evaluate the melt viscosity during injection process is developed in this work. The formulations to coupling melt viscosity with fill time and injection pressure are derived and then the melt viscosity is determined. A test mold is prepared to evaluate the accuracy on viscosity calculations between the PSB module and the conventional approaches. The influence of melt viscosity on the tensile strength of molded part is proposed to study the consistency of injection quality.
Abstract: The Elliptic Curve Digital Signature Algorithm
(ECDSA) is the elliptic curve analogue of DSA, where it is a digital
signature scheme designed to provide a digital signature based on a
secret number known only to the signer and also on the actual
message being signed. These digital signatures are considered the
digital counterparts to handwritten signatures, and are the basis for
validating the authenticity of a connection. The security of these
schemes results from the infeasibility to compute the signature
without the private key. In this paper we introduce a proposed to
development the original ECDSA with more complexity.
Abstract: Many medical devices are driven by motor pumps. Some researchers reported that the vibration mainly affected medical devices using a motor pump. The purpose of this study was to examine the effect of stiffness and damping coefficient in a 3-dimensional (3D) model of a motor pump and spring. In the present paper, experimental and mathematical tests for the moments of inertia of the 3D model and the material properties were investigated by an INSTRON machine. The response surfaces could be generated by using 3D multi-body analysis and the design of experiment method. It showed that differences in contours of the response surface were clearly found for the particular area. Displacement of the center of the motor pump was decreased at K≈2000 N/M, C≈12.5 N-sec/M. However, the frequency was increased at K≈2000 N/M, C≈15 N-sec/M. In this study, this study suggested experimental technique for vibration reduction for a motor pump in medical device. The combined method suggested in this study will greatly contribute to design of medical devices concerning vibration and noise intervention.
Abstract: This paper proposes view-point insensitive human
pose recognition system using neural network. Recognition system
consists of silhouette image capturing module, data driven database,
and neural network. The advantages of our system are first, it is
possible to capture multiple view-point silhouette images of 3D human
model automatically. This automatic capture module is helpful to
reduce time consuming task of database construction. Second, we
develop huge feature database to offer view-point insensitivity at pose
recognition. Third, we use neural network to recognize human pose
from multiple-view because every pose from each model have similar
feature patterns, even though each model has different appearance and
view-point. To construct database, we need to create 3D human model
using 3D manipulate tools. Contour shape is used to convert silhouette
image to feature vector of 12 degree. This extraction task is processed
semi-automatically, which benefits in that capturing images and
converting to silhouette images from the real capturing environment is
needless. We demonstrate the effectiveness of our approach with
experiments on virtual environment.
Abstract: In this paper, a new reverse converter for the moduli set {2n, 2n–1, 2n–1–1} is presented. We improved a previously introduced conversion algorithm for deriving an efficient hardware design for reverse converter. Hardware architecture of the proposed converter is based on carry-save adders and regular binary adders, without the requirement for modular adders. The presented design is faster than the latest introduced reverse converter for moduli set {2n, 2n–1, 2n–1–1}. Also, it has better performance than the reverse converters for the recently introduced moduli set {2n+1–1, 2n, 2n–1}
Abstract: Pressure driven microscale gas flow-separation has
been investigated by solving the compressible Navier-Stokes (NS)
system of equations. A two dimensional explicit finite volume (FV)
compressible flow solver has been developed using modified
advection upwind splitting methods (AUSM+) with no-slip/first
order Maxwell-s velocity slip conditions to predict the flowseparation
behavior in microdimensions. The effects of scale-factor
of the flow geometry and gas species on the microscale gas flowseparation
have been studied in this work. The intensity of flowseparation
gets reduced with the decrease in scale of the flow
geometry. In reduced dimension, flow-separation may not at all be
present under similar flow conditions compared to the larger flow
geometry. The flow-separation patterns greatly depend on the
properties of the medium under similar flow conditions.
Abstract: This study extends research on the relationship
between marketing strategy and market segmentation by
investigating on market segments in the cement industry.
Competitive strength and rivals distance from the factory were used
as business environment. A three segment (positive, neutral or
indifferent and zero zones) were identified as strategic segments. For
each segment a marketing strategy (aggressive, defensive and
decline) were developed. This study employed data from cement
industry to fulfill two objectives, the first is to give a framework to
the segmentation of cement industry and the second is developing
marketing strategy with varying competitive strength. Fifty six
questionnaires containing close-and open-ended questions were
collected and analyzed. Results supported the theory that segments
tend to be more aggressive than defensive when competitive strength
increases. It is concluded that high strength segments follow total
market coverage, concentric diversification and frontal attack to their
competitors. With decreased competitive strength, Business tends to
follow multi-market strategy, product modification/improvement and
flank attack to direct competitors for this kind of segments. Segments
with weak competitive strength followed focus strategy and decline
strategy.