Abstract: This paper proposed classification models that would
be used as a proxy for hard disk drive (HDD) functional test equitant
which required approximately more than two weeks to perform the
HDD status classification in either “Pass" or “Fail". These models
were constructed by using committee network which consisted of a
number of single neural networks. This paper also included the
method to solve the problem of sparseness data in failed part, which
was called “enforce learning method". Our results reveal that the
constructed classification models with the proposed method could
perform well in the sparse data conditions and thus the models,
which used a few seconds for HDD classification, could be used to
substitute the HDD functional tests.
Abstract: A technique proposed for the automatic detection
of spikes in electroencephalograms (EEG). A multi-resolution
approach and a non-linear energy operator are exploited. The
signal on each EEG channel is decomposed into three sub bands
using a non-decimated wavelet transform (WT). The WT is a
powerful tool for multi-resolution analysis of non-stationary signal
as well as for signal compression, recognition and restoration.
Each sub band is analyzed by using a non-linear energy operator,
in order to detect spikes. A decision rule detects the presence of
spikes in the EEG, relying upon the energy of the three sub-bands.
The effectiveness of the proposed technique was confirmed by
analyzing both test signals and EEG layouts.
Abstract: In this paper, we propose a method for detecting
circular shapes with subpixel accuracy. First, the geometric properties
of circles have been used to find the diameters as well as the
circumference pixels. The center and radius are then estimated by the
circumference pixels. Both synthetic and real images have been tested
by the proposed method. The experimental results show that the new
method is efficient.
Abstract: Microplasma welding is a less expensive alternative to
laser welding in dental technology. The aim of the study was to
highlight discontinuities present in the microplasma welded joints of
dental base metal alloys by visual analysis. Five base metal alloys
designated for fixed prostheses manufacture were selected for the
experiments. Using these plates, preliminary tests were conducted by
microplasma welding in butt joint configuration, without filler
material, bilaterally and with filler material, proper for each base
metal. Macroscopic visual inspection was performed to assess
carefully the irregularities in the welds. Electron microscopy allowed
detection of discontinuities that are not visible to the eye and
revealing details regarding location, trajectory, morphology and size
of discontinuities. Supplementing visual control with microscopic
analysis allows to detect small discontinuities, which escapes the
macroscopic control and to make a detailed study of the weld.
Abstract: The objective of this study is to present the test
results of variable air volume (VAV) air conditioning system
optimized by two objective genetic algorithm (GA). The objective
functions are energy savings and thermal comfort. The optimal set
points for fuzzy logic controller (FLC) are the supply air temperature
(Ts), the supply duct static pressure (Ps), the chilled water
temperature (Tw), and zone temperature (Tz) that is taken as the
problem variables. Supply airflow rate and chilled water flow rate are
considered to be the constraints. The optimal set point values are
obtained from GA process and assigned into fuzzy logic controller
(FLC) in order to conserve energy and maintain thermal comfort in
real time VAV air conditioning system. A VAV air conditioning
system with FLC installed in a software laboratory has been taken for
the purpose of energy analysis. The total energy saving obtained in
VAV GA optimization system with FLC compared with constant air
volume (CAV) system is expected to achieve 31.5%. The optimal
duct static pressure obtained through Genetic fuzzy methodology
attributes to better air distribution by delivering the optimal quantity
of supply air to the conditioned space. This combination enhanced
the advantages of uniform air distribution, thermal comfort and
improved energy savings potential.
Abstract: When dealing with safety in structures, the connections between structural components play an important role. Robustness of a structure as a whole depends both on the load- bearing capacity of the structural component and on the structures capacity to resist total failure, even though a local failure occurs in a component or a connection between components. To avoid progressive collapse it is necessary to be able to carry out a design for connections. A connection may be executed with anchors to withstand local failure of the connection in structures built with prefabricated components. For the design of these anchors, a model is developed for connections in structures performed in prefabricated autoclaved aerated concrete components. The design model takes into account the effect of anchors placed close to the edge, which may result in splitting failure. Further the model is developed to consider the effect of reinforcement diameter and anchor depth. The model is analytical and theoretically derived assuming a static equilibrium stress distribution along the anchor. The theory is compared to laboratory test, including the relevant parameters and the model is refined and theoretically argued analyzing the observed test results. The method presented can be used to improve safety in structures or even optimize the design of the connections
Abstract: This paper presents a multi-objective formulation for
optimal siting and sizing of distributed generation (DG) resources in
distribution systems in order to minimize the cost of power losses
and energy not supplied. The implemented technique is based on
particle swarm optimization (PSO) and weight method that employed
to obtain the best compromise between these costs. Simulation
results on 33-bus distribution test system are presented to
demonstrate the effectiveness of the proposed procedure.
Abstract: Celiac disease is an immune-mediated disease, triggered in genetically susceptible individuals by ingested gluten from wheat, rye, barley and other closely related cereal grains. The only effective treatment is a strict gluten free diet for life. Latvian producers do not offer gluten-free products. In this research, use of extruded maize flour was tested for substituting rice, maize or buckwheat flour in gluten-free bread formulations at different ratios. Also the influence of extruded maize flour on the quality parameters of gluten-free bread was investigated. The aim of research was to study the influence of extruded maize flour on gluten-free bread quality. Addition of extruded maize flour affect gluten-free bread crumb color, structure of crumb, weight loss and dry off of bread.
Abstract: Recent fifteen years witnessed fast improvements in the field of humanoid robotics. The human-like robot structure is
more suitable to human environment with its supreme obstacle avoidance properties when compared with wheeled service robots.
However, the walking control for bipedal robots is a challenging task
due to their complex dynamics. Stable reference generation plays a very important role in control.
Linear Inverted Pendulum Model (LIPM) and the Zero Moment Point (ZMP) criterion are applied in a number of studies for stable
walking reference generation of biped walking robots. This paper follows this main approach too. We propose a natural and continuous ZMP reference trajectory for a stable and human-like walk. The ZMP reference trajectories move forward under the sole of the support foot when the robot body is supported by a single leg. Robot center of mass trajectory is obtained
from predefined ZMP reference trajectories by a Fourier series
approximation method. The Gibbs phenomenon problem common with Fourier approximations of discontinuous functions is avoided by employing continuous ZMP references. Also, these ZMP reference
trajectories possess pre-assigned single and double support phases,
which are very useful in experimental tuning work.
The ZMP based reference generation strategy is tested via threedimensional
full-dynamics simulations of a 12-degrees-of-freedom
biped robot model. Simulation results indicate that the proposed reference trajectory generation technique is successful.
Abstract: The purpose of this paper is to present the design and
instrumentation of a new benchmark multivariable nonlinear control
laboratory. The mathematical model of this system may be used to
test the applicability and performance of various nonlinear control
procedures. The system is a two degree-of-freedom robotic arm with
soft and hard (discontinuous) nonlinear terms. Two novel
mechanisms are designed to allow the implementation of adjustable
Coulomb friction and backlash.
Abstract: Polypropylene blended with natural oil and pigment additives has been studied. Different formulations for each compound were made into polybag used for cultivation of oil palm seedlings for strength and mechanical properties studies. One group of sample was exposed under normal sunlight to initiate degradation and another group of sample was placed under shaded area for five months. All samples were tested for tensile strength to determine the degradation effects. The tensile strength of directly exposed sunlight samples and shaded area showed up to 50% and 25% degradation respectively. However, similar reduction of Young’s modulus for all samples was found for both exposures. Structural investigations were done using FTIR to detect deformation. The natural additives that were used in the studies were all natural and environmental friendly
Abstract: The power system network is becoming more
complex nowadays and it is very difficult to maintain the stability
of the system. Today-s enhancement of technology makes it
possible to include new energy storage devices in the electric
power system. In addition, with the aid of power electronic
devices, it is possible to independently exchange active and
reactive power flow with the utility grid. The main purpose of this
paper proposes a Proportional – Integral (PI) control based 48 –
pulse Inverter based Static Synchronous Series Compensator
(SSSC) with and without Superconducting Magnetic Energy
Storage (SMES) used for enhancing the transient stability and
regulating power flow in automatic mode. Using a test power
system through the dynamic simulation in Matlab/Simulink
platform validates the performance of the proposed SSSC with and
without SMES system.
Abstract: Nowadays the devices of night vision are widely used both for military and civil applications. The variety of night vision applications require a variety of the night vision devices designs. A web-based architecture of a software system for design assessment before producing of night vision devices is developed. The proposed architecture of the web-based system is based on the application of a mathematical model for designing of night vision devices. An algorithm with two components – for iterative design and for intelligent design is developed and integrated into system architecture. The iterative component suggests compatible modules combinations to choose from. The intelligent component provides compatible combinations of modules satisfying given user requirements to device parameters. The proposed web-based architecture of a system for design assessment of night vision devices is tested via a prototype of the system. The testing showed the applicability of both iterative and intelligent components of algorithm.
Abstract: In this study the extracts of the Iraqi herb Tribulus
terrestris (Al-Hassage or Al-Kutub) was done by using of polar and
non polar solvents, then the biological activity of these extractants
was studied in three fields, First, the antibacterial activity (in vitro)
on gram positive bacteria (Staphylococcus aureus), and gram
negative bacteria (E. coli, Proteus vulgaris, Pseudomonas
aerugiuosa, and Klebsiella), all extracts showed considerable activity
against all bacteria. Second, the effect of extracts on free serum
testosterone level in male mice (in vivo), the alcoholic, and
acetonitrilic extracts showed significant (P < 0.05) increase in free
serum testosterone level, and we found that the extracts contained
compounds with less genotoxic effects in mice germ cells. 3rd, was to
study the effect of methanolic extract of T. terrestris in diabetes
management.
Abstract: Electronic banking must be secure and easy to use and
many banks heavily advertise an apparent of 100% secure system
which is contestable in many points. In this work, an alternative
approach to the design of e-banking system, through a new solution
for user authentication and security with digital certificate called
LumaCert is introduced. The certificate applies new algorithm for
asymmetric encryption by utilizing two mathematical operators
called Pentors and UltraPentors. The public and private key in this
algorithm represent a quadruple of parameters which are directly
dependent from the above mentioned operators. The strength of the
algorithm resides in the inability to find the respective Pentor and
UltraPentor operator from the mentioned parameters.
Abstract: In this paper, a new automated methodology to detect the optic disc (OD) automatically in retinal images from patients with risk of being affected by Diabetic Retinopathy (DR) and Macular Edema (ME) is presented. The detection procedure comprises two independent methodologies. On one hand, a location methodology obtains a pixel that belongs to the OD using image contrast analysis and structure filtering techniques and, on the other hand, a boundary segmentation methodology estimates a circular approximation of the OD boundary by applying mathematical morphology, edge detection techniques and the Circular Hough Transform. The methodologies were tested on a set of 1200 images composed of 229 retinographies from patients affected by DR with risk of ME, 431 with DR and no risk of ME and 540 images of healthy retinas. The location methodology obtained 98.83% success rate, whereas the OD boundary segmentation methodology obtained good circular OD boundary approximation in 94.58% of cases. The average computational time measured over the total set was 1.67 seconds for OD location and 5.78 seconds for OD boundary segmentation.
Abstract: The main objectives of this study were to identify
attributes that influence customer satisfaction and determine their
relationships with customer satisfaction. The variables included in
this research are place/ambience, food quality and service quality as
independent variables and customer satisfaction as the dependent
variable. A survey questionnaire which consisted of three parts to
measure demographic factors, independent variables, and dependent
variables was constructed based on items determined by past
research. 149 respondents from one of the well known hotel in Kuala
Lumpur, MALAYSIA were selected as a sample. Psychometric
testing was conducted to determine the reliability and validity of the
questionnaire. From the findings, there were positive significant
relationship between place/ambience (r=0.563**, p=0.000) and
service quality (r=0.544**, p=0.000) with customer satisfaction.
However, although relationship between food quality and customer
satisfaction was significant, it was in the negative direction (r=-
0.268**, p=0.001). New findings were discovered after conducting
this research and previous research findings were strengthened by the
results of this research. Future researchers could concentrate on
determining attributes that influence customer satisfaction when
cost/price is not a factor and reasons for place/ambience is currently
becoming the leading factor in determining customer satisfaction.
Abstract: The direct synthesis process of dimethyl ether (DME)
from syngas in slurry reactors is considered to be promising because
of its advantages in caloric transfer. In this paper, the influences of
operating conditions (temperature, pressure and weight hourly space
velocity) on the conversion of CO, selectivity of DME and methanol
were studied in a stirred autoclave over Cu-Zn-Al-Zr slurry catalyst,
which is far more suitable to liquid phase dimethyl ether synthesis
process than bifunctional catalyst commercially. A Langmuir-
Hinshelwood mechanism type global kinetics model for liquid phase
DME direct synthesis based on methanol synthesis models and a
methanol dehydration model has been investigated by fitting our
experimental data. The model parameters were estimated with
MATLAB program based on general Genetic Algorithms and
Levenberg-Marquardt method, which is suitably fitting experimental
data and its reliability was verified by statistical test and residual
error analysis.
Abstract: This qualitative, quantitative mixed-method study explores how students- motivation and interest in creative hands-on activities affected their conceptual understanding of science. The objectives of this research include developing a greater understanding about how creative activities, incorporated into the classroom as instructional strategies, increase student motivation and their learning or mastery of science concepts. The creative activities are viewed as a motivational tool, a specific type of task, which have an impact on student goals. Pre-and-post tests, pre-and-post interviews, and student responses measure motivational-goal theory variables, interest in the activity, and conceptual change. Implications for education and future research will be discussed.
Abstract: HIV-1 genome is highly heterogeneous. Due to this
variation, features of HIV-I genome is in a wide range. For this
reason, the ability to infection of the virus changes depending on
different chemokine receptors. From this point of view, R5 HIV
viruses use CCR5 coreceptor while X4 viruses use CXCR5 and
R5X4 viruses can utilize both coreceptors. Recently, in
Bioinformatics, R5X4 viruses have been studied to classify by using
the experiments on HIV-1 genome.
In this study, R5X4 type of HIV viruses were classified using
Auto Regressive (AR) model through Artificial Neural Networks
(ANNs). The statistical data of R5X4, R5 and X4 viruses was
analyzed by using signal processing methods and ANNs. Accessible
residues of these virus sequences were obtained and modeled by AR
model since the dimension of residues is large and different from
each other. Finally the pre-processed data was used to evolve various
ANN structures for determining R5X4 viruses. Furthermore ROC
analysis was applied to ANNs to show their real performances. The
results indicate that R5X4 viruses successfully classified with high
sensitivity and specificity values training and testing ROC analysis
for RBF, which gives the best performance among ANN structures.