Abstract: Sewer deposits have been identified as a major cause
of dysfunctions in combined sewer systems regarding sewer
management, which induces different negative consequents resulting
in poor hydraulic conveyance, environmental damages as well as
worker’s health. In order to overcome the problematics of
sedimentation, flushing has been considered as the most operative
and cost-effective way to minimize the sediments impacts and
prevent such challenges. Flushing, by prompting turbulent wave
effects, can modify the bed form depending on the hydraulic
properties and geometrical characteristics of the conduit. So far, the
dynamics of the bed-load during high-flow events in combined sewer
systems as a complex environment is not well understood, mostly due
to lack of measuring devices capable to work in the “hostile” in
combined sewer system correctly. In this regards, a one-episode
flushing issue from an opening gate valve with weir function was
carried out in a trunk sewer in Paris to understand its cleansing
efficiency on the sediments (thickness: 0-30 cm). During more than
1h of flushing within 5 m distance in downstream of this flushing
device, a maximum flowrate and a maximum level of water have
been recorded at 5 m in downstream of the gate as 4.1 m3/s and 2.1
m respectively. This paper is aimed to evaluate the efficiency of this
type of gate for around 1.1 km (from the point -50 m to +1050 m in
downstream from the gate) by (i) determining bed grain-size
distribution and sediments evolution through the sewer channel, as
well as their organic matter content, and (ii) identifying sections that
exhibit more changes in their texture after the flush. For the first one,
two series of sampling were taken from the sewer length and then
analyzed in laboratory, one before flushing and second after, at same
points among the sewer channel. Hence, a non-intrusive sampling
instrument has undertaken to extract the sediments smaller than the
fine gravels. The comparison between sediments texture after the
flush operation and the initial state, revealed the most modified zones
by the flush effect, regarding the sewer invert slope and hydraulic
parameters in the zone up to 400 m from the gate. At this distance,
despite the increase of sediment grain-size rages, D50 (median grainsize)
varies between 0.6 mm and 1.1 mm compared to 0.8 mm and 10
mm before and after flushing, respectively. Overall, regarding the
sewer channel invert slope, results indicate that grains smaller than
sands (< 2 mm) are more transported to downstream along about 400
m from the gate: in average 69% before against 38% after the flush
with more dispersion of grain-sizes distributions. Furthermore, high
effect of the channel bed irregularities on the bed material evolution
has been observed after the flush.
Abstract: Industries produce millions of cubic meters of effluent
every year and the wastewater produced may be released into the
surrounding water bodies, treated on-site or at municipal treatment
plants. The determination of organic matter in the wastewater
generated is very important to avoid any negative effect on the
aquatic ecosystem. The scope of the present work is to assess the
physicochemical composition of the wastewater produced from one
of the brewery industry in South Africa. This is to estimate the
environmental impact of its discharge into the receiving water bodies
or the municipal treatment plant. The parameters monitored for the
quantitative analysis of brewery wastewater include biological
oxygen demand (BOD5), chemical oxygen demand (COD), total
suspended solids, volatile suspended solids, ammonia, total oxidized
nitrogen, nitrate, nitrite, phosphorus and alkalinity content. In
average, the COD concentration of the brewery effluent was 5340.97
mg/l with average pH values of 4.0 to 6.7. The BOD5 and the solids
content of the wastewater from the brewery industry were high. This
means that the effluent is very rich in organic content and its
discharge into the water bodies or the municipal treatment plant could
cause environmental pollution or damage the treatment plant. In
addition, there were variations in the wastewater composition
throughout the monitoring period. This might be as a result of
different activities that take place during the production process, as
well as the effects of peak period of beer production on the water
usage.
Abstract: This paper applied factor conditions from Porter’s
Diamond Model (1990) to understand the various challenges facing
the AMISA. Factor conditions highlighted in Porter’s model are
grouped into two groups namely, basic and advance factors. Two
AMISA associations representing over 10 000 employees were
interviewed. The largest Clothing, Textiles and Leather (CTL)
apparel retail group was also interviewed with a government
department implementing the industrialization policy were
interviewed. The paper points out that AMISA have basic factor conditions
necessary for competitive advantage in the apparel industries.
However advance factor creation has proven to be a challenge for
AMISA, Higher Education Institutions (HEIs) and government. Poor
infrastructural maintenance has contributed to high manufacturing
costs and poor quick response technologies. The use of Porter’s
Factor Conditions as a tool to analyze the sector’s competitive
advantage challenges and opportunities has increased knowledge
regarding factors that limit the AMISA’s competitiveness. It is
therefore argued that other studies on Porter’s Diamond model
factors like Demand conditions, Firm strategy, structure and rivalry
and Related and supporting industries can be used to analyze the
situation of the AMISA for the purposes of improving competitive
advantage.
Abstract: The objective of the study is to assess the
implementation of LED lighting into forest machine work in the dark.
In addition, the paper includes a wide variety of important and
relevant safety and health parameters. In modern, computerized work
in the cab of forest machines, artificial illumination is a demanding
task when performing duties, such as the visual inspections of wood
and computer calculations. We interviewed entrepreneurs and
gathered the following as the most pertinent themes: (1) safety, (2)
practical problems, and (3) work with LED lighting. The most
important comments were in regards to the practical problems of
LED lighting. We found indications of technical problems in
implementing LED lighting, like snow and dirt on the surfaces of
lamps that dim the emission of light. Moreover, service work in the
dark forest is dangerous and increases the risks of on-site accidents.
We also concluded that the amount of blue light to the eyes should be
assessed, especially, when the drivers are working in a semi-dark cab.
Abstract: In this paper, we provided a literature survey on the
artificial stock problem (ASM). The paper began by exploring the
complexity of the stock market and the needs for ASM. ASM
aims to investigate the link between individual behaviors (micro
level) and financial market dynamics (macro level). The variety of
patterns at the macro level is a function of the AFM complexity. The
financial market system is a complex system where the relationship
between the micro and macro level cannot be captured analytically.
Computational approaches, such as simulation, are expected to
comprehend this connection. Agent-based simulation is a simulation
technique commonly used to build AFMs. The paper proceeds by
discussing the components of the ASM. We consider the roles
of behavioral finance (BF) alongside the traditionally risk-averse
assumption in the construction of agent’s attributes. Also, the
influence of social networks in the developing of agents interactions is
addressed. Network topologies such as a small world, distance-based,
and scale-free networks may be utilized to outline economic
collaborations. In addition, the primary methods for developing
agents learning and adaptive abilities have been summarized.
These incorporated approach such as Genetic Algorithm, Genetic
Programming, Artificial neural network and Reinforcement Learning.
In addition, the most common statistical properties (the stylized facts)
of stock that are used for calibration and validation of ASM are
discussed. Besides, we have reviewed the major related previous
studies and categorize the utilized approaches as a part of these
studies. Finally, research directions and potential research questions
are argued. The research directions of ASM may focus on the macro
level by analyzing the market dynamic or on the micro level by
investigating the wealth distributions of the agents.
Abstract: Sustainability is a very important and heavily
discussed subject, expanding through tourism as well. The study
proposition was to collect data and present it to the competent bodies
so they can mold their public policies to improve the conditions of
the site. It was hypothesized that the lack of data is currently
affecting the quality of life and the sustainable development of the
site and the tourism. The research was held in Mateiros, a city in the
state of Tocantins (TO)/Brasil near Palmas, its capital city. Because
of the concentration of tourists during the high season and several
tourist attractions being around, the research took place in Mateiros.
The methodological procedure had a script of theoretical construction
and investigation of the deductive scientific method parameters
through a case study in the Jalapão/TO/Brazil region, using it as a
tool for a questionnaire given to the competent bodies in an interview
system with the UN sustainability indexes as a base. In the three
sustainable development scope: environmental, social and economic,
the results indicated that the data presented by the interviewed were
scarce or nonexistent. It shows that more research is necessary,
providing the tools for the ones responsible to propose action plans to
improve the site, strengthening the tourism and making it even more
sustainable.
Abstract: The MEMS pressure sensor has been introduced and
presented in this paper. The types of pressure sensor and its theory of
operation are also included. The latest MEMS technology, the
fabrication processes of pressure sensor are explored and discussed.
Besides, various device applications of pressure sensor such as tire
pressure-monitoring system, diesel particulate filter and others are
explained. Due to further miniaturization of the device nowadays, the
pressure sensor with nanotechnology (NEMS) is also reviewed. The
NEMS pressure sensor is expected to have better performance as well
as lower in its cost. It has gained an excellent popularity in many
applications.
Abstract: The lifetime of a wireless sensor network can be
effectively increased by using scheduling operations. Once the
sensors are randomly deployed, the task at hand is to find the largest
number of disjoint sets of sensors such that every sensor set provides
complete coverage of the target area. At any instant, only one of these
disjoint sets is switched on, while all other are switched off. This
paper proposes a heuristic search method to find the maximum
number of disjoint sets that completely cover the region. A
population of randomly initialized members is made to explore the
solution space. A set of heuristics has been applied to guide the
members to a possible solution in their neighborhood. The heuristics
escalate the convergence of the algorithm. The best solution explored
by the population is recorded and is continuously updated. The
proposed algorithm has been tested for applications which require
sensing of multiple target points, referred to as point coverage
applications. Results show that the proposed algorithm outclasses the
existing algorithms. It always finds the optimum solution, and that
too by making fewer number of fitness function evaluations than the
existing approaches.
Abstract: This paper presents a state-of-the-art survey of the
operations research models developed for internal audit planning.
Two alternative approaches have been followed in the literature for
audit planning: (1) identifying the optimal audit frequency; and (2)
determining the optimal audit resource allocation. The first approach
identifies the elapsed time between two successive audits, which can
be presented as the optimal number of audits in a given planning
horizon, or the optimal number of transactions after which an audit
should be performed. It also includes the optimal audit schedule. The
second approach determines the optimal allocation of audit frequency
among all auditable units in the firm. In our review, we discuss both
the deterministic and probabilistic models developed for audit
planning. In addition, game theory models are reviewed to find the
optimal auditing strategy based on the interactions between the
auditors and the clients.
Abstract: The goal of this experiment is to evaluate the
effectiveness of different leachate pre-treatment options in terms of
COD and ammonia removal. This research focused on the evaluation
of physical-chemical methods for pre-treatment of leachate that
would be effective and rapid in order to satisfy the requirements of
the sewer discharge by-laws. The four pre-treatment options
evaluated were: air stripping, chemical coagulation, electrocoagulation
and advanced oxidation with sodium ferrate. Chemical
coagulation reported the best COD removal rate at 43%, compared to
18% for both air stripping and electro-coagulation, and 20% for
oxidation with sodium ferrate. On the other hand, air stripping was
far superior to the other treatment options in terms of ammonia
removal with 86%. Oxidation with sodium ferrate reached only 16%,
while chemical coagulation and electro-coagulation removed less
than 10%. When combined, air stripping and chemical coagulation
removed up to 50% COD and 85% ammonia.
Abstract: Background subtraction and temporal difference are
often used for moving object detection in video. Both approaches are
computationally simple and easy to be deployed in real-time image
processing. However, while the background subtraction is highly
sensitive to dynamic background and illumination changes, the
temporal difference approach is poor at extracting relevant pixels of
the moving object and at detecting the stopped or slowly moving
objects in the scene. In this paper, we propose a simple moving object
detection scheme based on adaptive background subtraction and
temporal difference exploiting dynamic background updates. The
proposed technique consists of histogram equalization, a linear
combination of background and temporal difference, followed by the
novel frame-based and pixel-based background updating techniques.
Finally, morphological operations are applied to the output images.
Experimental results show that the proposed algorithm can solve the
drawbacks of both background subtraction and temporal difference
methods and can provide better performance than that of each method.
Abstract: Breast cancer is in the top rate of cancer. We analyzed
the prevalence of obesity and its association with breast cancer and
finally we reviewed 25 article that 320 patient and 320 control which
enrolled to our study. The distribution of breast cancer patients and
controls with respect to their anthropometric indices in patients with
higher weight, which was statistically significant (60.2 ± 10.2 kg)
compared with control group (56.1 ± 11.3 kg). The body mass index
of patients was (26.06+/-3.42) and significantly higher than the
control group (24.1+/-1.7). Obesity leads to increased levels of
adipose tissue in the body that can be stored toxins and carcinogens
to produce a continuous supply. Due to the high level of fat and the
role of estrogen in a woman which is endogenous estrogen of the
tumor and regulates the activities of growth steroids, obesity has
confirmed as a risk factor for breast cancer. Our study and other
studies have shown that obesity is a risk factor for breast cancer. And
it can be prevented with a weight loss intervention for breast cancer
in the future.
Abstract: Mitigating soil erosion, especially in Mediterranean
countries such as Greece, is essential in order to maintain
environmental and agricultural sustainability. In this paper, scientific
publications related to soil erosion studies in Greece were reviewed
and categorized. To accomplish this, the online search engine of
Scopus was used. The key words were “soil”, “erosion” and
“Greece.” An analysis of the published articles was conducted at
three levels: i) type of publication, ii) chronologic and iii) thematic. A
hundred and ten publications published in scientific journals were
reviewed. The results showed that the awareness regarding the soil
erosion in Greece has increased only in the last decades. The
publications covered a wide range of thematic categories such as the
type of studied areas, the physical phenomena that trigger and
influence the soil erosion, the negative anthropogenic impacts on
them, the assessment tools that were used in order to examine the
threat and the proper management. The analysis of these articles was
significant and necessary in order to find the scientific gaps of soil
erosion studies in Greece and help enhance the sustainability of soil
management in the future.
Abstract: This paper presents an application of a “Systematic
Soft Domain Driven Design Framework” as a soft systems approach
to domain-driven design of information systems development. The
framework use SSM as a guiding methodology within which we have
embedded a sequence of design tasks based on the UML leading to
the implementation of a software system using the Naked Objects
framework. This framework have been used in action research
projects that have involved the investigation and modelling of
business processes using object-oriented domain models and the
implementation of software systems based on those domain models.
Within this framework, Soft Systems Methodology (SSM) is used as
a guiding methodology to explore the problem situation and to
develop the domain model using UML for the given business
domain. The framework is proposed and evaluated in our previous
works, and a real case study “Information Retrieval System for
academic research” is used, in this paper, to show further practice and
evaluation of the framework in different business domain. We argue
that there are advantages from combining and using techniques from
different methodologies in this way for business domain modelling.
The framework is overviewed and justified as multimethodology
using Mingers multimethodology ideas.
Abstract: Given the limited research on Small and Mediumsized
Enterprises’ (SMEs) contribution to Corporate Social
Responsibility (CSR) and even scarcer research on Swiss SMEs, this
paper helps to fill these gaps by enabling the identification of supranational
SME parameters. Thus, the paper investigates the current
state of SME practices in Switzerland and across 15 other countries.
Combining the degree to which SMEs demonstrate an explicit (or
business case) approach or see CSR as an implicit moral activity with
the assessment of their attributes for “variety of capitalism” defines
the framework of this comparative analysis. To outline Swiss small
business CSR patterns in particular, 40 SME owner-managers were
interviewed. A secondary data analysis of studies from different
countries laid groundwork for this comparative overview of small
business CSR. The paper identifies Swiss small business CSR as
driven by norms, values, and by the aspiration to contribute to
society, thus, as an implicit part of the day-to-day business. Similar to
most Central European, Mediterranean, Nordic, and Asian countries,
explicit CSR is still very rare in Swiss SMEs. Astonishingly, also
British and American SMEs follow this pattern in spite of their strong
and distinctly liberal market economies. Though other findings show
that nationality matters this research concludes that SME culture and
an informal CSR agenda are strongly formative and superseding even
forces of market economies, nationally cultural patterns, and
language. Hence, classifications of countries by their market system,
as found in the comparative capitalism literature, do not match the
CSR practices in SMEs as they do not mirror the peculiarities of their
business. This raises questions on the universality and
generalisability of unmediated, explicit management concepts,
especially in the context of small firms.
Abstract: Experts, enterprises and operators expect that the
bandwidth request will increase up to rates of 100 to 1,000 Mbps
within several years. Therefore the most important question is which
technology shall satisfy the future consumer broadband demands.
Currently the consensus is, that the fiber technology has the best
technical characteristics to achieve such the high bandwidth rates.
But fiber technology is so far very cost-intensive and resource
consuming. To avoid these investments, operators are concentrating
to upgrade the existing copper and hybrid fiber coax infrastructures.
This work presents a comparison of the copper and fiber
technologies including an overview about the current German
broadband market. Both technologies are reviewed in the terms of
demand, willingness to pay and economic efficiency in connection
with the technical characteristics.
Abstract: This paper shows the connection between emoticons and politeness in written computer-mediated communication. It studies if there are some differences in the use of emoticon between Czech and English written tweets. The assumptions about the use of emoticons were based on the use of greetings and thanks in real, faceto-face situations. The first assumption, that welcome greeting phrase would be accompanied by positive emoticon, was correct. But for the farewell greeting are both positive and negative emoticons possible. The results show lower frequency of negative emoticons in this context. There were also quite often found both positive and negative emoticon in the same tweet. The expression of gratitude is associated with positive emotions. The results show that emoticons accompany polite phrases of greeting and thanks very often both in Czech and English. The use of emoticons with studied polite phrases shows that emoticons have become an integral part of these phrases.
Abstract: Complex lifting entry was selected for precise landing
performance during the Mars Science Laboratory entry. This study
aims to develop the three-dimensional numerical method for precise
computation and the surface panel method for rapid engineering
prediction. Detailed flow field analysis for Mars exploration mission
was performed by carrying on a series of fully three-dimensional
Navier-Stokes computations. The static aerodynamic performance was
then discussed, including the surface pressure, lift and drag coefficient,
lift-to-drag ratio with the numerical and engineering method.
Computation results shown that the shock layer is thin because of
lower effective specific heat ratio, and that calculated results from both
methods agree well with each other, and is consistent with the
reference data. Aerodynamic performance analysis shows that CG
location determines trim characteristics and pitch stability, and certain
radially and axially shift of the CG location can alter the capsule lifting
entry performance, which is of vital significance for the aerodynamic
configuration design and inner instrument layout of the Mars entry
capsule.
Abstract: This paper introduces a video sharing platform based
on WiFi, which consists of camera, mobile phone and PC server. This
platform can receive wireless signal from the camera and show the live
video on the mobile phone captured by camera. In addition, it is able to
send commands to camera and control the camera’s holder to rotate.
The platform can be applied to interactive teaching and dangerous
area’s monitoring and so on. Testing results show that the platform can
share the live video of mobile phone. Furthermore, if the system’s PC
server and the camera and many mobile phones are connected
together, it can transfer photos concurrently.
Abstract: The problem of finding control laws for underactuated
systems has attracted growing attention since these systems are
characterized by the fact that they have fewer actuators than the
degrees of freedom to be controlled. The acrobot, which is a planar
two-link robotic arm in the vertical plane with an actuator at the elbow
but no actuator at the shoulder, is a representative in underactuated
systems. In this paper, the dynamic model of the acrobot is
implemented using Mathworks’ Simscape. And the sliding mode
control is constructed using MATLAB and Simulink.