Abstract: At very high speeds, bubbles form in the underwater vehicles because of sharp trailing edges or of places where the local pressure is lower than the vapor pressure. These bubbles are called cavities and the size of the cavities grows as the velocity increases. A properly designed cavitator can induce the formation of a single big cavity all over the vehicle. Such a vehicle travelling in the vaporous cavity is called a supercavitating vehicle and the present research work mainly focuses on the dynamic modeling of such vehicles. Cavitation of the fins is also accounted and the effect of the same on trajectory is well explained. The entire dynamics has been developed using the state space approach and emphasis is given on the effect of size and angle of attack of the cavitator. Control law has been established for the motion of the vehicle using Non-linear Dynamic Inverse (NDI) with cavitator as the control surface.
Abstract: The fault detection and diagnosis of complicated
production processes is one of essential tasks needed to run the process
safely with good final product quality. Unexpected events occurred in
the process may have a serious impact on the process. In this work,
triangular representation of process measurement data obtained in an
on-line basis is evaluated using simulation process. The effect of using
linear and nonlinear reduced spaces is also tested. Their diagnosis
performance was demonstrated using multivariate fault data. It has
shown that the nonlinear technique based diagnosis method produced
more reliable results and outperforms linear method. The use of
appropriate reduced space yielded better diagnosis performance. The
presented diagnosis framework is different from existing ones in that it
attempts to extract the fault pattern in the reduced space, not in the
original process variable space. The use of reduced model space helps
to mitigate the sensitivity of the fault pattern to noise.
Abstract: In this paper the neural network-based controller is
designed for motion control of a mobile robot. This paper treats the
problems of trajectory following and posture stabilization of the
mobile robot with nonholonomic constraints. For this purpose the
recurrent neural network with one hidden layer is used. It learns
relationship between linear velocities and error positions of the
mobile robot. This neural network is trained on-line using the
backpropagation optimization algorithm with an adaptive learning
rate. The optimization algorithm is performed at each sample time to
compute the optimal control inputs. The performance of the proposed
system is investigated using a kinematic model of the mobile robot.
Abstract: Liver segmentation is the first significant process for
liver diagnosis of the Computed Tomography. It segments the liver
structure from other abdominal organs. Sophisticated filtering techniques
are indispensable for a proper segmentation. In this paper, we
employ a 3D anisotropic diffusion as a preprocessing step. While
removing image noise, this technique preserve the significant parts
of the image, typically edges, lines or other details that are important
for the interpretation of the image. The segmentation task is done
by using thresholding with automatic threshold values selection and
finally the false liver region is eliminated using 3D connected component.
The result shows that by employing the 3D anisotropic filtering,
better liver segmentation results could be achieved eventhough simple
segmentation technique is used.
Abstract: Truss spars are used for oil exploitation in deep and ultra-deep water if storage crude oil is not needed. The linear hydrodynamic analysis of truss spar in random sea wave load is necessary for determining the behaviour of truss spar. This understanding is not only important for design of the mooring lines, but also for optimising the truss spar design. In this paper linear hydrodynamic analysis of truss spar is carried out in frequency domain. The hydrodynamic forces are calculated using the modified Morison equation and diffraction theory. Added mass and drag coefficients of truss section computed by transmission matrix and normal acceleration and velocity component acting on each element and for hull section computed by strip theory. The stiffness properties of the truss spar can be separated into two components; hydrostatic stiffness and mooring line stiffness. Then, platform response amplitudes obtained by solved the equation of motion. This equation is non-linear due to viscous damping term therefore linearised by iteration method [1]. Finally computed RAOs and significant response amplitude and results are compared with experimental data.
Abstract: A biophysically based multilayer continuum model of the facial soft tissue composite has been developed for simulating wrinkle formation. The deformed state of the soft tissue block was determined by solving large deformation mechanics equations using the Galerkin finite element method. The proposed soft tissue model is composed of four layers with distinct mechanical properties. These include stratum corneum, epidermal-dermal layer (living epidermis and dermis), subcutaneous tissue and the underlying muscle. All the layers were treated as non-linear, isotropic Mooney Rivlin materials. Contraction of muscle fibres was approximated using a steady-state relationship between the fibre extension ratio, intracellular calcium concentration and active stress in the fibre direction. Several variations of the model parameters (stiffness and thickness of epidermal-dermal layer, thickness of subcutaneous tissue layer) have been considered.
Abstract: Grobner basis calculation forms a key part of computational
commutative algebra and many other areas. One important
ramification of the theory of Grobner basis provides a means to solve
a system of non-linear equations. This is why it has become very
important in the areas where the solution of non-linear equations is
needed, for instance in algebraic cryptanalysis and coding theory. This
paper explores on a parallel-distributed implementation for Grobner
basis calculation over GF(2). For doing so Buchberger algorithm is
used. OpenMP and MPI-C language constructs have been used to
implement the scheme. Some relevant results have been furnished
to compare the performances between the standalone and hybrid
(parallel-distributed) implementation.
Abstract: Processing the data by computers and performing
reasoning tasks is an important aim in Computer Science. Semantic
Web is one step towards it. The use of ontologies to enhance the
information by semantically is the current trend. Huge amount of
domain specific, unstructured on-line data needs to be expressed in
machine understandable and semantically searchable format.
Currently users are often forced to search manually in the results
returned by the keyword-based search services. They also want to use
their native languages to express what they search. In this paper, an
ontology-based automated question answering system on software
test documents domain is presented. The system allows users to enter
a question about the domain by means of natural language and
returns exact answer of the questions. Conversion of the natural
language question into the ontology based query is the challenging
part of the system. To be able to achieve this, a new algorithm
regarding free text to ontology based search engine query conversion
is proposed. The algorithm is based on investigation of suitable
question type and parsing the words of the question sentence.
Abstract: Saturated two-phase fluid flows are often subject to
pressure induced oscillations. Due to compressibility the vapor
bubbles act as a spring with an asymmetric non-linear characteristic.
The volume of the vapor bubbles increases or decreases differently if
the pressure fluctuations are compressing or expanding;
consequently, compressing pressure fluctuations in a two-phase pipe
flow cause less displacement in the direction of the pipe flow than
expanding pressure fluctuations. The displacement depends on the
ratio of liquid to vapor, the ratio of pressure fluctuations over average
pressure and on the exciting frequency of the pressure fluctuations.
In addition, pressure fluctuations in saturated vapor bubbles cause
condensation and evaporation within the bubbles and change
periodically the ratio between liquid to vapor, and influence the
dynamical parameters for the oscillation. The oscillations are
conforming to an isenthalpic process at constant enthalpy with no
heat transfer and no exchange of work.
The paper describes the governing non-linear equation for twophase
fluid oscillations with condensation and evaporation, and
presents steady state approximate solutions for free and for pressure
induced oscillations. Resonance criteria and stability are discussed.
Abstract: Flat double-layer grid is from category of space structures that are formed from two flat layers connected together with diagonal members. Increased stiffness and better seismic resistance in relation to other space structures are advantages of flat double layer space structures. The objective of this study is assessment and calculation of Behavior factor of flat double layer space structures. With regarding that these structures are used widely but Behavior factor used to design these structures against seismic force is not determined and exact, the necessity of study is obvious. This study is theoretical. In this study we used structures with span length of 16m and 20 m. All connections are pivotal. ANSYS software is used to non-linear analysis of structures.
Abstract: The linear SEF (Spectral Edge Frequency) parameter
and spectrum analysis method can not reflect the non-linear of EEG.
This method can not contribute to acquire real time analysis and obtain
a high confidence in the clinic due to low discrimination. To solve the
problems, the development of a new index is carried out using the
bispectrum analyzing the EEG(electroencephalogram) including the
non-linear characteristic. After analyzing the bispectrum of the 2
dimension, the most significant power spectrum density peaks appeared abundantly at the specific area in awakening and anesthesia state. These points are utilized to create the new index since many
peaks appeared at the specific area in the frequency coordinate. The measured range of an index was 0-100. An index is 20-50 at an anesthesia, while the index is 90-60 at the awake. New index could afford to effectively discriminate the awake and anesthesia state.
Abstract: Many systems in the natural world exhibit chaos or non-linear behavior, the complexity of which is so great that they appear to be random. Identification of chaos in experimental data is essential for characterizing the system and for analyzing the predictability of the data under analysis. The Lyapunov exponents provide a quantitative measure of the sensitivity to initial conditions and are the most useful dynamical diagnostic for chaotic systems. However, it is difficult to accurately estimate the Lyapunov exponents of chaotic signals which are corrupted by a random noise. In this work, a method for estimation of Lyapunov exponents from noisy time series using unscented transformation is proposed. The proposed methodology was validated using time series obtained from known chaotic maps. In this paper, the objective of the work, the proposed methodology and validation results are discussed in detail.
Abstract: Since supply chains highly impact the financial
performance of companies, it is important to optimize and analyze
their Key Performance Indicators (KPI). The synergistic combination
of Particle Swarm Optimization (PSO) and Monte Carlo simulation is
applied to determine the optimal reorder point of warehouses in
supply chains. The goal of the optimization is the minimization of the
objective function calculated as the linear combination of holding and
order costs. The required values of service levels of the warehouses
represent non-linear constraints in the PSO. The results illustrate that
the developed stochastic simulator and optimization tool is flexible
enough to handle complex situations.
Abstract: This article provides partial evaluation index and its
standard of sports aerobics, including the following 12 indexes: health
vitality, coordination, flexibility, accuracy, pace, endurance, elasticity,
self-confidence, form, control, uniformity and musicality. The
three-layer BP artificial neural network model including input layer,
hidden layer and output layer is established. The result shows that the
model can well reflect the non-linear relationship between the
performance of 12 indexes and the overall performance. The predicted
value of each sample is very close to the true value, with a relative
error fluctuating around of 5%, and the network training is successful.
It shows that BP network has high prediction accuracy and good
generalization capacity if being applied in sports aerobics performance
evaluation after effective training.
Abstract: In power systems, protective relays must filter their
inputs to remove undesirable quantities and retain signal quantities of
interest. This job must be performed accurate and fast. A new
method for filtering the undesirable components such as DC and
harmonic components associated with the fundamental system
signals. The method is s based on a dynamic filtering algorithm. The
filtering algorithm has many advantages over some other classical
methods. It can be used as dynamic on-line filter without the need of
parameters readjusting as in the case of classic filters. The proposed
filter is tested using different signals. Effects of number of samples
and sampling window size are discussed. Results obtained are
presented and discussed to show the algorithm capabilities.
Abstract: Because support interference corrections are not properly
understood, engineers mostly rely on expensive dummy measurements
or CFD calculations. This paper presents a method based on uncorrected wind tunnel measurements and fast calculation techniques
(it is a hybrid method) to calculate wall interference, support interference and residual interference (when e.g. a support member
closely approaches the wind tunnel walls) for any type of wind tunnel and support configuration. The method provides with a simple formula
for the calculation of the interference gradient. This gradient is
based on the uncorrected measurements and a successive calculation
of the slopes of the interference-free aerodynamic coefficients. For the latter purpose a new vortex-lattice routine is developed that corrects
the slopes for viscous effects. A test case of a measurement on a wing proves the value of this hybrid method as trends and orders of
magnitudes of the interference are correctly determined.
Abstract: In this paper, the two-dimension differential transformation method (DTM) is employed to obtain the closed form solutions of the three famous coupled partial differential equation with physical interest namely, the coupled Korteweg-de Vries(KdV) equations, the coupled Burgers equations and coupled nonlinear Schrödinger equation. We begin by showing that how the differential transformation method applies to a linear and non-linear part of any PDEs and apply on these coupled PDEs to illustrate the sufficiency of the method for this kind of nonlinear differential equations. The results obtained are in good agreement with the exact solution. These results show that the technique introduced here is accurate and easy to apply.
Abstract: The main objective developed in this paper is to find a
graphic technique for modeling, simulation and diagnosis of the
industrial systems. This importance is much apparent when it is about
a complex system such as the nuclear reactor with pressurized water
of several form with various several non-linearity and time scales. In
this case the analytical approach is heavy and does not give a fast
idea on the evolution of the system. The tool Bond Graph enabled us
to transform the analytical model into graphic model and the
software of simulation SYMBOLS 2000 specific to the Bond Graphs
made it possible to validate and have the results given by the
technical specifications. We introduce the analysis of the problem
involved in the faults localization and identification in the complex
industrial processes. We propose a method of fault detection applied
to the diagnosis and to determine the gravity of a detected fault. We
show the possibilities of application of the new diagnosis approaches
to the complex system control. The industrial systems became
increasingly complex with the faults diagnosis procedures in the
physical systems prove to become very complex as soon as the
systems considered are not elementary any more. Indeed, in front of
this complexity, we chose to make recourse to Fault Detection and
Isolation method (FDI) by the analysis of the problem of its control
and to conceive a reliable system of diagnosis making it possible to
apprehend the complex dynamic systems spatially distributed applied
to the standard pressurized water nuclear reactor.
Abstract: This experiment discusses the effects of fracture
parameters such as depth, length, width, angle and the number of the
fracture to the conductance properties of laterite using the DUK-2B
digital electrical measurement system combined with the method of
simulating the fractures. The results of experiment show that the
changes of fracture parameters produce effects to the conductance
properties of laterite. There is a clear degressive period of the
conductivity of laterite during increasing the depth, length, width, or
the angle and the quantity of fracture gradually. When the depth of
fracture exceeds the half thickness of the soil body, the conductivity of
laterite shows evidently non-linear diminishing pattern and the
amplitude of decrease tends to increase. The length of fracture has
fewer effects than the depth to the conductivity. When the width of
fracture reaches some fixed values, the change of the conductivity is
less sensitive to the change of the width, and at this time, the
conductivity of laterite maintains at a stable level. When the angle of
fracture is less than 45°, the decrease of the conductivity is more
clearly as the angle increases. But when angle is more than 45°,
change of the conductivity is relatively gentle as the angle increases.
The increasing quantity of the fracture causes the other fracture
parameters having great impact on the change of conductivity. When
moisture content and temperature were unchanged, depth and angle of
fractures are the major factors affecting the conductivity of laterite
soil; quantity, length, and width are minor influencing factors. The
sensitivity of fracture parameters affect conductivity of laterite soil is:
depth >angles >quantity >length >width.
Abstract: Power system stabilizers (PSS) are now routinely used in the industry to damp out power system oscillations. In this paper, particle swarm optimization (PSO) technique is applied to design a robust power system stabilizer (PSS). The design problem of the proposed controller is formulated as an optimization problem and PSO is employed to search for optimal controller parameters. By minimizing the time-domain based objective function, in which the deviation in the oscillatory rotor speed of the generator is involved; stability performance of the system is improved. The non-linear simulation results are presented under wide range of operating conditions; disturbances at different locations as well as for various fault clearing sequences to show the effectiveness and robustness of the proposed controller and their ability to provide efficient damping of low frequency oscillations. Further, all the simulations results are compared with a conventionally designed power system stabilizer to show the superiority of the proposed design approach.