Abstract: Phytophthora cinnamomi (P. c) is a plant pathogenic
oomycete that is capable of damaging plants in commercial production
systems and natural ecosystems worldwide. The most common
methods for the detection and diagnosis of P. c infection are
expensive, elaborate and time consuming. This study was carried out
to examine whether species specific and life cycle specific volatile
organic compounds (VOCs) can be absorbed by solid-phase
microextraction fibers and detected by gas chromatography that are
produced by P. c and another oomycete Pythium dissotocum. A
headspace solid-phase microextraction (HS-SPME) together with gas
chromatography (GC) method was developed and optimized for the
identification of the VOCs released by P. c. The optimized parameters
included type of fiber, exposure time, desorption temperature and
desorption time. Optimization was achieved with the analytes of P.
c+V8A and V8A alone. To perform the HS-SPME, six types of fiber
were assayed and compared: 7μm Polydimethylsiloxane (PDMS),
100μm Polydimethylsiloxane (PDMS), 50/30μm
Divinylbenzene/CarboxenTM/Polydimethylsiloxane
DVB/CAR/PDMS), 65μm Polydimethylsiloxane/Divinylbenzene
(PDMS/DVB), 85μm Polyacrylate (PA) fibre and 85μm CarboxenTM/
Polydimethylsiloxane (Carboxen™/PDMS). In a comparison of the
efficacy of the fibers, the bipolar fiber DVB/CAR/PDMS had a higher
extraction efficiency than the other fibers. An exposure time of 16h
with DVB/CAR/PDMS fiber in the sample headspace was enough to
reach the maximum extraction efficiency. A desorption time of 3min
in the GC injector with the desorption temperature of 250°C was
enough for the fiber to desorb the compounds of interest. The chromatograms and morphology study confirmed that the VOCs from
P. c+V8A had distinct differences from V8A alone, as did different
life cycle stages of P. c and different taxa such as Pythium dissotocum.
The study proved that P. c has species and life cycle specific VOCs,
which in turn demonstrated the feasibility of this method as means of
Abstract: TTV is an unenveloped circular single-stranded DNA
virus with a diameter of 30-32 nm that first was described in 1997 in
Japan. TTV was detected in various populations without proven
pathology, including blood donors and in patients with chronic HBV
and HCV hepatitis. The aim of this study was to determine the
prevalence of TTV DNA in Iranian patients with chronic hepatitis B
and C. Viral TTV-DNA was studied in 442 samples (202 with HBV,
138 with HCV and 102 controls) collected from west south of Iran.
All extracted serum DNA was amplified by TTV ORF1 gene specific
primers using the semi nested PCR technique. TTV DNA was
detected in the serum of 8.9% and 10.8% patients with chronic
hepatitis B and C, respectively. Prevalence of TTV-DNA in the serum
of 102 controls was 2.9%. Results showed significant relation of TTV
with HBV and HCV in patients by using T test examination (P
Abstract: The aim of this paper is to confirm the effect of key
design parameters, the punch radius and punch angle, on rupture of the
expansion tube using a finite element analysis with a ductile damage
model. The results of the finite element analysis indicated that the
expansion ratio of the tube was mainly affected by the radius of the
punch. However, the rupture was more affected by the punch angle
than the radius of the punch. The existence of a specific punch angle,
at which rupture did not occur, even if the radius of the punch was
increased, was found.
Abstract: This paper presents a novel approach for the design of
microwave circuits using Adaptive Network Fuzzy Inference
Optimizer (ANFIO). The method takes advantage of direct synthesis
of subsections of the amplifier using very fast and accurate ANFIO
models based on exact simulations using ADS. A mapping from
course space to fine space known as space mapping is also used. The
proposed synthesis approach takes into account the noise and
scattering parameters due to parasitic elements to achieve optimal
results. The overall ANFIO system is capable of designing different
LNAs at different noise and scattering criteria. This approach offers
significantly reduced time in the design of microwave amplifiers
within the validity range of the ANFIO system. The method has been
proven to work efficiently for a 2.4GHz LNA example. The S21 of
10.1 dB and noise figure (NF) of 2.7 dB achieved for ANFIO while
S21 of 9.05 dB and NF of 2.6 dB achieved for ANN.
Abstract: Protein-protein interactions (PPI) play a crucial role in many biological processes such as cell signalling, transcription, translation, replication, signal transduction, and drug targeting, etc. Structural information about protein-protein interaction is essential for understanding the molecular mechanisms of these processes. Structures of protein-protein complexes are still difficult to obtain by biophysical methods such as NMR and X-ray crystallography, and therefore protein-protein docking computation is considered an important approach for understanding protein-protein interactions. However, reliable prediction of the protein-protein complexes is still under way. In the past decades, several grid-based docking algorithms based on the Katchalski-Katzir scoring scheme were developed, e.g., FTDock, ZDOCK, HADDOCK, RosettaDock, HEX, etc. However, the success rate of protein-protein docking prediction is still far from ideal. In this work, we first propose a more practical measure for evaluating the success of protein-protein docking predictions,the rate of first success (RFS), which is similar to the concept of mean first passage time (MFPT). Accordingly, we have assessed the ZDOCK bound and unbound benchmarks 2.0 and 3.0. We also createda new benchmark set for protein-protein docking predictions, in which the complexes have experimentally determined binding affinity data. We performed free energy calculation based on the solution of non-linear Poisson-Boltzmann equation (nlPBE) to improve the binding mode prediction. We used the well-studied thebarnase-barstarsystem to validate the parameters for free energy calculations. Besides,thenlPBE-based free energy calculations were conducted for the badly predicted cases by ZDOCK and ZRANK. We found that direct molecular mechanics energetics cannot be used to discriminate the native binding pose from the decoys.Our results indicate that nlPBE-based calculations appeared to be one of the promising approaches for improving the success rate of binding pose predictions.
Abstract: Production of hard-to-cut materials with uncoated carbide cutting tools in turning, not only cause tool life reduction but also, impairs the product surface roughness. In this paper, influence of hot machining method were studied and presented in two cases. Case1-Workpiece surface roughness quality with constant cutting parameter and 300 ºC initial workpiece surface temperature. Case 2- Tool temperature variation when cutting with two speeds 78.5 (m/min) and 51 (m/min). The workpiece material and tool used in this study were AISI 1060 steel (45HRC) and uncoated carbide TNNM 120408-SP10(SANDVIK Coromant) respectively. A gas flam heating source was used to preheating of the workpiece surface up to 300 ºC, causing reduction of yield stress about 15%. Results obtained experimentally, show that the method used can considerably improved surface quality of the workpiece.
Abstract: In this paper, the optical generation of three bands of
continuously tunable millimeter-wave signals using an optical phase
modulator (OPM) and a polarization state rotation filter (PSRF) as an
optical notch filter is analyzed. The effect of the chromatic dispersion
on millimeter-wave signals is presented.
Abstract: In this paper we present a novel error model for
packet loss and subsequent error description. The proposed model
simulates the error performance of wireless communication link. The
model is designed as two independent Markov chains, where the first
one is used for packet generation and the second one generates
correctly and incorrectly transmitted bits for received packets from
the first chain. The statistical analyses of real communication on the
wireless link are used for determination of model-s parameters. Using
the obtained parameters and the implementation of the generator, we
collected generated traffic. The obtained results generated by
proposed model are compared with the real data collection.
Abstract: Periodicities in the environmetric time series can be
idyllically assessed by utilizing periodic models. In this
communication fugitive emission of gases from open sewer channel
Lyari which follows periodic behaviour are approximated by
employing periodic autoregressive model of order p. The orders of
periodic model for each season are selected through the examination
of periodic partial autocorrelation or information criteria. The
parameters for the selected order of season are estimated individually
for each emitted air toxin. Subsequently, adequacies of fitted models
are established by examining the properties of the residual for each
season. These models are beneficial for schemer and administrative
bodies for the improvement of implemented policies to surmount
future environmental problems.
Abstract: The purpose of this work is to present the potential of
solar energy in Zarqa region. The solar radiation along year 2009 was
obtained from Pyranometer which measures the global radiation over
horizontal surfaces. Solar data in several different forms, over period
of 5 minutes, hour-by-hour, daily and monthly data radiation have
been presented. Briefly, the yearly global solar radiation in Zarqa is
7297.5 MJ/m2 (2027 kWh/m²) and the average annual solar radiation
per day is 20 MJ/m2 (5.5 Kwh/m2). More specifically, the average
annual solar radiation per day is 12.9 MJ/m2 (3.57 Kwh/m2) in winter
and 25 MJ/m2 (7 Kwh/m2) in summer.
Abstract: In this paper we consider a nonlinear feedback
control called augmented automatic choosing control (AACC)
using the automatic choosing functions of gradient optimization
type for nonlinear systems. Constant terms which arise from sectionwise
linearization of a given nonlinear system are treated as
coefficients of a stable zero dynamics. Parameters included in the
control are suboptimally selected by minimizing the Hamiltonian
with the aid of the genetic algorithm. This approach is applied to
a field excitation control problem of power system to demonstrate
the splendidness of the AACC. Simulation results show that the
new controller can improve performance remarkably well.
Abstract: Due to adverse pressure gradient along the diverging
walls of wide-angled diffusers, the attached flow separates from
one wall and remains attached permanently to the other wall in a
process called stalling. Stalled diffusers render the whole fluid flow
system, in which they are part of, very inefficient. There is then an
engineering need to try to understand the whole process of diffuser
stall if any meaningful attempts to improve on diffuser efficiency
are to be made. In this regard, this paper provides a data bank
contribution for the mean flow-field in wide-angled diffusers where
the complete velocity and static pressure fields, and pressure recovery
data for diffusers in the fully stalled flow regime are experimentally
measured. The measurements were carried out at Reynolds numbers
between 1.07×105 and 2.14×105 based on inlet hydraulic diameter
and centreline velocity for diffusers whose divergence angles were
between 30Ôùª and 50Ôùª. Variation of Reynolds number did not significantly
affect the velocity and static pressure profiles. The wall static
pressure recovery was found to be more sensitive to changes in the
Reynolds number. By increasing the velocity from 10 m/s to 20 m/s,
the wall static pressure recovery increased by 8.31%. However, as the
divergence angle was increased, a similar increase in the Reynolds
number resulted in a higher percentage increase in pressure recovery.
Experimental results showed that regardless of the wall to which
the flow was attached, both the velocity and pressure fields were
replicated with discrepancies below 2%.
Abstract: Most HWRs currently use natural uranium fuel. Using enriched uranium fuel results in a significant improvement in fuel cycle costs and uranium utilization. On the other hand, reactivity changes of HWRs over the full range of operating conditions from cold shutdown to full power are small. This reduces the required reactivity worth of control devices and minimizes local flux distribution perturbations, minimizing potential problems due to transient local overheating of fuel. Analyzing heavy water effectiveness on neutronic parameters such as enrichment requirements, peaking factor and reactivity is important and should pay attention as primary concepts of a HWR core designing. Two nuclear nuclear reactors of CANDU-type and hexagonal-type reactor cores of 33 fuel assemblies and 19 assemblies in 1.04 P/D have been respectively simulated using MCNP-4C code. Using heavy water and light water as moderator have been compared for achieving less reactivity insertion and enrichment requirements. Two fuel matrixes of (232Th/235U)O2 and (238/235U)O2 have been compared to achieve more economical and safe design. Heavy water not only decreased enrichment needs, but it concluded in negative reactivity insertions during moderator density variations. Thorium oxide fuel assemblies of 2.3% enrichment loaded into the core of heavy water moderator resulted in 0.751 fission to absorption ratio and peaking factor of 1.7 using. Heavy water not only provides negative reactivity insertion during temperature raises which changes moderator density but concluded in 2 to 10 kg reduction of enrichment requirements, depend on geometry type.
Abstract: This article discusses the problem of estimating the
orientation of inclined ground on which a human subject stands based
on information provided by the vestibular system consisting of the
otolith and semicircular canals. It is assumed that body segments are
not necessarily aligned and thus forming an open kinematic chain.
The semicircular canals analogues to a technical gyrometer provide a
measure of the angular velocity whereas the otolith analogues to a
technical accelerometer provide a measure of the translational
acceleration. Two solutions are proposed and discussed. The first is
based on a stand-alone Kalman filter that optimally fuses the two
measurements based on their dynamic characteristics and their noise
properties. In this case, no body dynamic model is needed. In the
second solution, a central extended disturbance observer that
incorporates a body dynamic model (internal model) is employed.
The merits of both solutions are discussed and demonstrated by
experimental and simulation results.
Abstract: The back-propagation algorithm calculates the weight
changes of an artificial neural network, and a two-term algorithm
with a dynamically optimal learning rate and a momentum factor
is commonly used. Recently the addition of an extra term, called a
proportional factor (PF), to the two-term BP algorithm was proposed.
The third term increases the speed of the BP algorithm. However,
the PF term also reduces the convergence of the BP algorithm, and
optimization approaches for evaluating the learning parameters are
required to facilitate the application of the three terms BP algorithm.
This paper considers the optimization of the new back-propagation
algorithm by using derivative information. A family of approaches
exploiting the derivatives with respect to the learning rate, momentum
factor and proportional factor is presented. These autonomously
compute the derivatives in the weight space, by using information
gathered from the forward and backward procedures. The three-term
BP algorithm and the optimization approaches are evaluated using
the benchmark XOR problem.
Abstract: Acute toxicity of nano SiO2, ZnO, MCM-41 (Meso
pore silica), Cu, Multi Wall Carbon Nano Tube (MWCNT), Single
Wall Carbon Nano Tube (SWCNT) , Fe (Coated) to bacteria Vibrio
fischeri using a homemade luminometer , was evaluated. The values
of the nominal effective concentrations (EC), causing 20% and 50%
inhibition of biouminescence, using two mathematical models at two
times of 5 and 30 minutes were calculated. Luminometer was
designed with Photomultiplier (PMT) detector. Luminol
chemiluminescence reaction was carried out for the calibration graph.
In the linear calibration range, the correlation coefficients and
coefficient of Variation (CV) were 0.988 and 3.21% respectively
which demonstrate the accuracy and reproducibility of the instrument
that are suitable. The important part of this research depends on how
to optimize the best condition for maximum bioluminescence. The
culture of Vibrio fischeri with optimal conditions in liquid media,
were stirring at 120 rpm at a temperature of 150C to 180C and were
incubated for 24 to 72 hours while solid medium was held at 180C
and for 48 hours. Suspension of nanoparticles ZnO, after 30 min
contact time to bacteria Vibrio fischeri, showed the highest toxicity
while SiO2 nanoparticles showed the lowest toxicity. After 5 min
exposure time, the toxicity of ZnO was the strongest and MCM-41
was the weakest toxicant component.
Abstract: The aim of this study was to analyse the most
important parameters determining the quality of the motion structure
of the basic classical dance jump – grand jeté.Research sample
consisted of 8 students of the Dance Conservatory in Brno. Using the
system Simi motion we performed a 3D kinematic analysis of the
jump. On the basis of the comparison of structure quality and
measured data of the grand jeté, we defined the optimal values of the
relevant parameters determining the quality of the performance. The
take-off speed should achieve about 2.4 m·s-1, the optimum take-off
angle is 28 - 30º. The take-off leg should swing backward at the
beginning of the flight phase with the minimum speed of 3.3 m·s-1.If
motor abilities of dancers achieve the level necessary for optimal
performance of a classical dance jump, there is room for certain
variability of the structure of the dance jump.
Abstract: Use of microemulsion in enhanced oil recovery has become more attractive in recent years because of its high level of extraction efficiency. Experimental investigations have been made on characterization of microemulsions of oil-brinesurfactant/ cosurfactant system for its use in enhanced oil recovery (EOR). Sodium dodecyl sulfate, propan-1-ol and heptane were selected as surfactant, cosurfactant and oil respectively for preparation of microemulsion. The effects of salinity on the relative phase volumes and solubilization parameters have also been studied. As salinity changes from low to high value, phase transition takes place from Winsor I to Winsor II via Winsor III. Suitable microemulsion composition has been selected based on its stability and ability to reduce interfacial tension. A series of flooding experiments have been performed using the selected microemulsion. The flooding experiments were performed in a core flooding apparatus using uniform sand pack. The core holder was tightly packed with uniform sands (60-100 mesh) and saturated with brines of different salinities. It was flooded with the brine at 25 psig and the absolute permeability was calculated from the flow rate of the through sand pack. The sand pack was then flooded with the crude oil at 800 psig to irreducible water saturation. The initial water saturation was determined on the basis of mass balance. Waterflooding was conducted by placing the coreholder horizontally at a constant injection pressure at 200 pisg. After water flooding, when water-cut reached above 95%, around 0.5 pore volume (PV) of the above microemulsion slug was injected followed by chasing water. The experiments were repeated using different composition of microemulsion slug. The additional recoveries were calculated by material balance. Encouraging results with additional recovery more than 20% of original oil in place above the conventional water flooding have been observed.
Abstract: An adaptive fuzzy PID controller with gain scheduling is proposed in this paper. The structure of the proposed gain scheduled fuzzy PID (GS_FPID) controller consists of both fuzzy PI-like controller and fuzzy PD-like controller. Both of fuzzy PI-like and PD-like controllers are weighted through adaptive gain scheduling, which are also determined by fuzzy logic inference. A modified genetic algorithm called accumulated genetic algorithm is designed to learn the parameters of fuzzy inference system. In order to learn the number of fuzzy rules required for the TSK model, the fuzzy rules are learned in an accumulated way. In other words, the parameters learned in the previous rules are accumulated and updated along with the parameters in the current rule. It will be shown that the proposed GS_FPID controllers learned by the accumulated GA perform well for not only the regular linear systems but also the higher order and time-delayed systems.
Abstract: We present a numerical study of the sensitivity of the so called time relaxation family of models of fluid motion with respect to the time relaxation parameter χ on the two dimensional cavity problem. The goal of the study is to compute and compare the sensitivity of the model using finite difference method (FFD) and sensitivity equation method (SEM).