Abstract: In the first part of the research work, an electrolyzer (10.16 cm dia and 24.13 cm height) to produce hydrogen and oxygen was constructed for single slice O2/H2 fuel cell using cation exchange membrane. The electrolyzer performance was tested with 23% NaOH, 30% NaOH, 30% KOH and 35% KOH electrolyte solution with current input 4 amp and 2.84 V from the rectifier. Rates of volume of hydrogen produced were 0.159 cm3/sec, 0.155 cm3/sec, 0.169 cm3/sec and 0.163 cm3/sec respectively from 23% NaOH, 30% NaOH, 30% KOH and 35% KOH solution. Rates of volume of oxygen produced were 0.212 cm3/sec, 0.201 cm3/sec, 0.227 cm3/sec and 0.219 cm3/sec respectively from 23% NaOH, 30% NaOH, 30% KOH and 35% KOH solution (1.5 L). In spite of being tested the increased concentration of electrolyte solution, the gas rate does not change significantly. Therefore, inexpensive 23% NaOH electrolyte solution was chosen to use as the electrolyte in the electrolyzer. In the second part of the research work, graphite serpentine flow plates, fiberglass end plates, stainless steel screen electrodes, silicone rubbers were made to assemble the single slice O2/H2 polymer electrolyte membrane fuel cell (PEMFC).
Abstract: This paper presents a fast and efficient on-line technique for estimating impedance of unbalanced loads in power systems. The proposed technique is an application of a discrete timedynamic filter based on stochastic estimation theory which is suitable for estimating parameters in noisy environment. The algorithm uses sets of digital samples of the distorted voltage and current waveforms of the non-linear load to estimate the harmonic contents of these two signal. The non-linear load impedance is then calculated from these contents. The method is tested using practical data. Results are reported and compared with those obtained using the conventional least error squares technique. In addition to the very accurate results obtained, the method can detect and reject bad measurements. This can be considered as a very important advantage over the conventional static estimation methods such as the least error square method.
Abstract: A current mirror (CM) based on self cascode MOSFETs low voltage analog and mixed mode structures has been proposed. The proposed CM has high output impedance and can operate at 0.5 V. P-Spice simulations confirm the high performance of this CM with a bandwidth of 6.0 GHz at input current of 100 μA.
Abstract: Knowledge Discovery in Databases (KDD) has
evolved into an important and active area of research because of
theoretical challenges and practical applications associated with the
problem of discovering (or extracting) interesting and previously
unknown knowledge from very large real-world databases. Rough
Set Theory (RST) is a mathematical formalism for representing
uncertainty that can be considered an extension of the classical set
theory. It has been used in many different research areas, including
those related to inductive machine learning and reduction of
knowledge in knowledge-based systems. One important concept
related to RST is that of a rough relation. In this paper we presented
the current status of research on applying rough set theory to KDD,
which will be helpful for handle the characteristics of real-world
databases. The main aim is to show how rough set and rough set
analysis can be effectively used to extract knowledge from large
databases.
Abstract: Routing places an important role in determining the
quality of service in wireless networks. The routing methods adopted
in wireless networks have many drawbacks. This paper aims to
review the current routing methods used in wireless networks. This
paper proposes an innovative solution to overcome the problems in
routing. This solution is aimed at improving the Quality of Service.
This solution is different from others as it involves the resuage of the
part of the virtual circuits. This improvement in quality of service is
important especially in propagation of multimedia applications like
video, animations etc. So it is the dire need to propose a new solution
to improve the quality of service in ATM wireless networks for
multimedia applications especially during this era of multimedia
based applications.
Abstract: In this paper, the application of GRNN in
modeling of SOFC fuel cells were studied. The parameters
are of interested as voltage and power value and the current
changes are investigated. In addition, the comparison between
GRNN neural network application and conventional method
was made. The error value showed the superlative results.
Abstract: This paper presents a novel control strategy of a threephase
four-wire Unified Power Quality (UPQC) for an improvement
in power quality. The UPQC is realized by integration of series and
shunt active power filters (APFs) sharing a common dc bus capacitor.
The shunt APF is realized using a thee-phase, four leg voltage source
inverter (VSI) and the series APF is realized using a three-phase,
three leg VSI. A control technique based on unit vector template
technique (UTT) is used to get the reference signals for series APF,
while instantaneous sequence component theory (ISCT) is used for
the control of Shunt APF. The performance of the implemented
control algorithm is evaluated in terms of power-factor correction,
load balancing, neutral source current mitigation and mitigation of
voltage and current harmonics, voltage sag and swell in a three-phase
four-wire distribution system for different combination of linear and
non-linear loads. In this proposed control scheme of UPQC, the
current/voltage control is applied over the fundamental supply
currents/voltages instead of fast changing APFs currents/voltages,
there by reducing the computational delay and the required sensors.
MATLAB/Simulink based simulations are obtained, which support
the functionality of the UPQC. MATLAB/Simulink based
simulations are obtained, which support the functionality of the
UPQC.
Abstract: The increasing interest on processing data created by
sensor networks has evolved into approaches to implement sensor
networks as databases. The aggregation operator, which calculates a
value from a large group of data such as computing averages or sums,
etc. is an essential function that needs to be provided when
implementing such sensor network databases. This work proposes to
add the DURING clause into TinySQL to calculate values during a
specific long period and suggests a way to implement the aggregation
service in sensor networks by applying materialized view and
incremental view maintenance techniques that is used in data
warehouses. In sensor networks, data values are passed from child
nodes to parent nodes and an aggregation value is computed at the root
node. As such root nodes need to be memory efficient and low
powered, it becomes a problem to recompute aggregate values from all
past and current data. Therefore, applying incremental view
maintenance techniques can reduce the memory consumption and
support fast computation of aggregate values.
Abstract: As business environments are rapidly changing,
the manufacturing system must be reconfigured to adapt to
various customer needs. In order to cope with this challenge, it
is quintessential to test industrial control logic rapidly and
easily in the design time, and monitor operational behavior in
the run time of automated manufacturing system. Proposed
integrated model for virtual prototyping and operational
monitoring of industrial control logic is to improve limitations
of current ladder programming practices and general discrete
event simulation method. Each plant layout model using HMI
package and object-oriented control logic model is designed
independently and is executed simultaneously in integrated
manner to reflect design practices of automation system in the
design time. Control logic is designed and executed using UML
activity diagram without considering complicated control
behavior to deal with current trend of reconfigurable
manufacturing. After the physical installation, layout model of
virtual prototype constructed in the design time is reused for
operational monitoring of system behavior during run time.
Abstract: A new technique based on Pattern search optimization is proposed for estimating different solar cell parameters in this paper. The estimated parameters are the generated photocurrent, saturation current, series resistance, shunt resistance, and ideality factor. The proposed approach is tested and validated using double diode model to show its potential. Performance of the developed approach is quite interesting which signifies its potential as a promising estimation tool.
Abstract: This paper presents a new approach for busbar protection with stable operation of current transformer during saturation, using fuzzy neuro and symmetrical components theory. This technique uses symmetrical components of current signals to learn the hidden relationship existing in the input patterns. Simulation studies are preformed and the influence of changing system parameters such as inception fault and source impedance is studied. Details of the design procedure and the results of performance studies with the proposed relay are given in the paper. An analysis of the performance of the proposed technique during ct saturation conditions is presented. The performance of the technique was investigated for a variety of operating conditions and for several busbar configurations. Data generated by EMTDC simulations of model power systems were used in the investigations. The results indicate that the proposed technique is stable during ct saturation conditions.
Abstract: A high-frequency low-power sinusoidal quadrature
oscillator is presented through the use of two 2nd-order low-pass
current-mirror (CM)-based filters, a 1st-order CM low-pass filter and
a CM bilinear transfer function. The technique is relatively simple
based on (i) inherent time constants of current mirrors, i.e. the
internal capacitances and the transconductance of a diode-connected
NMOS, (ii) a simple negative resistance RN formed by a resistor load
RL of a current mirror. Neither external capacitances nor inductances
are required. As a particular example, a 1.9-GHz, 0.45-mW, 2-V
CMOS low-pass-filter-based all-current-mirror sinusoidal quadrature
oscillator is demonstrated. The oscillation frequency (f0) is 1.9 GHz
and is current-tunable over a range of 370 MHz or 21.6 %. The
power consumption is at approximately 0.45 mW. The amplitude
matching and the quadrature phase matching are better than 0.05 dB
and 0.15°, respectively. Total harmonic distortions (THD) are less
than 0.3 %. At 2 MHz offset from the 1.9 GHz, the carrier to noise
ratio (CNR) is 90.01 dBc/Hz whilst the figure of merit called a
normalized carrier-to-noise ratio (CNRnorm) is 153.03 dBc/Hz. The
ratio of the oscillation frequency (f0) to the unity-gain frequency (fT)
of a transistor is 0.25. Comparisons to other approaches are also
included.
Abstract: This paper presents an algorithm for the recognition
and tracking of moving objects, 1/10 scale model car is used to verify
performance of the algorithm. Presented algorithm for the recognition
and tracking of moving objects in the paper is as follows. SURF
algorithm is merged with Lucas-Kanade algorithm. SURF algorithm
has strong performance on contrast, size, rotation changes and it
recognizes objects but it is slow due to many computational
complexities. Processing speed of Lucas-Kanade algorithm is fast but
the recognition of objects is impossible. Its optical flow compares the
previous and current frames so that can track the movement of a pixel.
The fusion algorithm is created in order to solve problems which
occurred using the Kalman Filter to estimate the position and the
accumulated error compensation algorithm was implemented. Kalman
filter is used to create presented algorithm to complement problems
that is occurred when fusion two algorithms. Kalman filter is used to
estimate next location, compensate for the accumulated error. The
resolution of the camera (Vision Sensor) is fixed to be 640x480. To
verify the performance of the fusion algorithm, test is compared to
SURF algorithm under three situations, driving straight, curve, and
recognizing cars behind the obstacles. Situation similar to the actual is
possible using a model vehicle. Proposed fusion algorithm showed
superior performance and accuracy than the existing object
recognition and tracking algorithms. We will improve the performance
of the algorithm, so that you can experiment with the images of the
actual road environment.
Abstract: In the classical buckling analysis of rectangular plates
subjected to the concurrent action of shear and uniaxial forces, the
Euler shear buckling stress is generally evaluated separately, so that
no influence on the shear buckling coefficient, due to the in-plane
tensile or compressive forces, is taken into account.
In this paper the buckling problem of simply supported rectangular
plates, under the combined action of shear and uniaxial forces, is
discussed from the beginning, in order to obtain new project formulas
for the shear buckling coefficient that take into account the presence
of uniaxial forces.
Furthermore, as the classical expression of the shear buckling
coefficient for simply supported rectangular plates is considered only
a “rough" approximation, as the exact one is defined by a system of
intersecting curves, the convergence and the goodness of the classical
solution are analyzed, too.
Finally, as the problem of the Euler shear buckling stress
evaluation is a very important topic for a variety of structures, (e.g.
ship ones), two numerical applications are carried out, in order to
highlight the role of the uniaxial stresses on the plating scantling
procedures and the goodness of the proposed formulas.
Abstract: Software testing is important stage of software development cycle. Current testing process involves tester and electronic documents with test case scenarios. In this paper we focus on new approach to testing process using automated test case generation and tester guidance through the system based on the model of the system. Test case generation and model-based testing is not possible without proper system model. We aim on providing better feedback from the testing process thus eliminating the unnecessary paper work.
Abstract: Intravitreal injection (IVI) is the most common treatment for eye posterior segment diseases such as endopthalmitis, retinitis, age-related macular degeneration, diabetic retinopathy, uveitis, and retinal detachment. Most of the drugs used to treat vitreoretinal diseases, have a narrow concentration range in which they are effective, and may be toxic at higher concentrations. Therefore, it is critical to know the drug distribution within the eye following intravitreal injection. Having knowledge of drug distribution, ophthalmologists can decide on drug injection frequency while minimizing damage to tissues. The goal of this study was to develop a computer model to predict intraocular concentrations and pharmacokinetics of intravitreally injected drugs. A finite volume model was created to predict distribution of two drugs with different physiochemical properties in the rabbit eye. The model parameters were obtained from literature review. To validate this numeric model, the in vivo data of spatial concentration profile from the lens to the retina were compared with the numeric data. The difference was less than 5% between the numerical and experimental data. This validation provides strong support for the numerical methodology and associated assumptions of the current study.
Abstract: The purpose of this paper is to examine the current
state of corporate social responsibility statements on corporate
websites of Malaysian and Singaporean corporations and analyze
how the CSR statements contribute in building a unique corporate
identity of corporations. Content analysis is employed to examine the
websites of Malaysian and Singaporean consumer corporations. It is
believed that generally most companies tend to publish and
communicate their CSR statements visibly to general stakeholders.
However, there is a significantly different outcome of the articulation
of CSR on practices on websites between Malaysian and Singaporean
consumer corporations. A number of Singaporean organizations were
found less concerned with CSR practices as compared to Malaysian
organizations. The findings indicate a need for corporations in
Malaysia and Singapore to orchestrate their core competence of CSR
activities in order to develop a unique corporate identity in a global
business environment.
Abstract: The oil and gas industry has moved towards Load and
Resistance Factor Design through API RP2A - LRFD and the
recently published international standard, ISO-19902, for design of
fixed steel offshore structures. The ISO 19902 is intended to provide
a harmonized design practice that offers a balanced structural fitness
for the purpose, economy and safety. As part of an ongoing work, the
reliability analysis of tubular joints of the jacket structure has been
carried out to calibrate the load and resistance factors for the design
of offshore platforms in Malaysia, as proposed in the ISO.
Probabilistic models have been established for the load effects (wave,
wind and current) and the tubular joints strengths. In this study the
First Order Reliability Method (FORM), coded in MATLAB
Software has been employed to evaluate the reliability index of the
typical joints, designed using API RP2A - WSD and ISO 19902.
Abstract: Bone remodeling occurs by the balanced action of
bone resorbing osteoclasts (OC) and bone-building osteoblasts.
Increased bone resorption by excessive OC activity contributes
to malignant and non-malignant diseases including osteoporosis.
To study OC differentiation and function, OC formed in
in vitro cultures are currently counted manually, a tedious
procedure which is prone to inter-observer differences. Aiming
for an automated OC-quantification system, classification of
OC and precursor cells was done on fluorescence microscope
images based on the distinct appearance of fluorescent nuclei.
Following ellipse fitting to nuclei, a combination of eight
features enabled clustering of OC and precursor cell nuclei.
After evaluating different machine-learning techniques, LOGREG
achieved 74% correctly classified OC and precursor cell
nuclei, outperforming human experts (best expert: 55%). In
combination with the automated detection of total cell areas,
this system allows to measure various cell parameters and most
importantly to quantify proteins involved in osteoclastogenesis.
Abstract: Distributed Generation (DG) in the form of renewable
power generation systems is currently preferred for clean power
generation. It has a significant impact on the distribution systems.
This impact may be either positively or negatively depending on the
distribution system, distributed generator and load characteristics. In
this works, an overview of DG is briefly introduced. The technology
of DG is also listed while the technical impacts and economic
impacts are explained.