Abstract: In this study, the three-dimensional cavitating
turbulent flow in a complete Francis turbine is simulated using
mixture model for cavity/liquid two-phase flows. Numerical analysis
is carried out using ANSYS CFX software release 12, and standard k-ε
turbulence model is adopted for this analysis. The computational
fluid domain consist of spiral casing, stay vanes, guide vanes, runner
and draft tube. The computational domain is discretized with a threedimensional
mesh system of unstructured tetrahedron mesh. The
finite volume method (FVM) is used to solve the governing equations
of the mixture model. Results of cavitation on the runner’s blades
under three different boundary conditions are presented and
discussed. From the numerical results it has been found that the
numerical method was successfully applied to simulate the cavitating
two-phase turbulent flow through a Francis turbine, and also
cavitation is clearly predicted in the form of water vapor formation
inside the turbine. By comparison the numerical prediction results
with a real runner; it’s shown that the region of higher volume
fraction obtained by simulation is consistent with the region of runner
cavitation damage.
Abstract: The importance of agribusiness development is
proved in accordance with the trends in the agricultural sector of
Georgia. Agribusiness environment and the consequences of the
agricultural reforms are evaluated. The factors hindering the
development of agribusiness are revealed and the ways for
overcoming these problems are suggested. SWOT analysis is done in
order to identify the needs of agribusiness. The needs of agribusiness
development in Georgia are evaluated by priorities: prevention of
diseases and reduction of the harm caused by these diseases,
accessibility of long-term agricultural loans with low interest rates,
improving qualification of farmers, the level of education and usage
of modern technologies, changes in legislation, accessibility to high
quality agricultural machinery, and the development of infrastructure.
Based on the outcomes of the research, agribusiness development
strategies in Georgia are suggested and appropriate priorities of
economic policy are determined. Conclusions are made and based on
these conclusions, some recommendations are suggested.
Abstract: The wider growing Finite Element Method (FEM)
application is caused by its benefits of cost saving and environment
friendly. Also, by using FEM a deep understanding of certain
phenomenon can be achieved. This paper observed the role of
material properties and volumetric change when Solid State Phase
Transformation (SSPT) takes place in residual stress formation due to
a welding process of ferritic steels through coupled Thermo-
Metallurgy-Mechanical (TMM) analysis. The correctness of FEM residual stress prediction was validated by
experiment. From parametric study of the FEM model, it can be
concluded that the material properties change tend to over-predicts
residual stress in the weld center whilst volumetric change tend to
underestimates it. The best final result is the compromise of both by
incorporates them in the model which has a better result compared to
a model without SSPT.
Abstract: The contemporary battlefield creates a demand for
more costly and highly advanced munitions. Training personnel
responsible for operations as well as immediate execution of combat
tasks which engage real asset is unrealistic and economically not
feasible. Owing to a wide array of exploited simulators and various
types of imitators, it is possible to reduce the costs. One of the
effective elements of training, which can be applied in the training of
all service branches, is imitator of aerial targets. This research serves
as an introduction to the commencement of design analysis over a
real aerial target imitator. Within the project, the basic aerodynamic
calculations were made, which enabled to determine its geometry,
design layout, performance as well as mass balance of individual
components. The conducted calculations of the parameters of flight
characteristics come closer to the real performance of such
Unmanned Aerial Vehicles.
Abstract: This investigation is focused on using of Mon dance
in Pathum Thani Province’s tradition and has the following
objectives: 1) to study the background of Mon dance in Pathum
Thani Province; 2) to study Mon dance in Pathum Thani Province;
and 3) to study of using Mon dance in Pathum Thani province’s
tradition. This qualitative research was conducted in Pathum Thani
province (in the central of Thailand). Data was collected from
documentary study and field data by means of observation, interview,
and group discussion. Workshops were also held with a total of 100
attendees, comprised of 20 key informants, 40 casual informants and
40 general informants. Data was validated using the triangulation
technique and the findings are presented using the descriptive
analysis. The results of the study show that the historical background
of Mon dance in Pathum Thani Province initiated during the war
evacuation from Martaban (south of Burma) to settle down in Sam
Khok, Pathum Thani Province in Ayutthaya period to Rattanakosin.
The study found that Mon dance typically consists of 12-13 dancing
process. The melodies have 12-13 songs. Piphat Mon (Mon
traditional music ensemble) is used in the performance. Performers
are dressed in Mon traditional costumes. The performers are 6-12
women and depending on the employer’s demands. Length of the
performance varies from the duration of music orchestration. Rituals
and customs performed are paying homage to teachers before the
performance. The offerings are composed of flowers, incense sticks,
candles, money gifts which are well arranged on a tray with pedestal,
and also liquors, tobaccos and pure water for asking propitiousness.
For the use of Mon dance in Pathum Thani Province’s tradition, it is
found that the dance is commonly performed in the funeral
ceremonial tradition at present because the physical postures of the
performance are considered graceful and exquisite. In addition, as for
its value, it has long been believed since the ancient times that Mon
dance was a sacred thing considered as the dignity and glorification
especially for funeral ceremonies of priest or royal hierarchy classes.
However, Mon dance has continued to be used in the traditions
associated with Mon people activities in Pathum Thani Province for
instance customary welcome for honor guest and Songkran festival.
Abstract: This study was conducted to investigate the
psychological variables motivating sport participation and
involvement among student-athletes of tertiary institutions in southwest
Nigeria. One thousand three hundred and fifty (N-1350) studentathletes
were randomly selected in all sports from nine tertiary
institutions in south-west Nigeria. These tertiary institutions include
University of Lagos, Lagos State University, Obafemi Awolowo
University, Osun State University, University of Ibadan, University
of Agriculture Abeokuta, Federal University of Technology
Akungba, University of Ilorin, and Kwara State University. The
descriptive survey research method was adopted while a self
developed validated Likert type questionnaire named Sport
Participation Scale (SPS) was used to elicit opinion from
respondents. The test-retest reliability value obtained for the
instrument, using Pearson Product Moment Correlation Co-efficient
was 0.96. Out of the one thousand three hundred and fifty (N-1350)
questionnaire administered, only one thousand two hundred and five
(N-1286) were correctly filled, coded and analysed using inferential
statistics of Chi-Square (X2) while all the tested hypotheses were set
at. 05 alpha level. Based on the findings of this study, the result
revealed that several psychological factors influence student athletes
to continue participation in sport one which includes love for the
game, famous athletes as role model and family support. However,
the analysis further revealed that the stipends the student-athletes get
from their universities have no influence on their participation and
involvement in sport.
Abstract: Round addition differential fault analysis using
operation skipping for lightweight block ciphers with on-the-fly key
scheduling is presented. For 64-bit KLEIN, it is shown that only a pair
of correct and faulty ciphertexts can be used to derive the secret master
key. For PRESENT, one correct ciphertext and two faulty ciphertexts
are required to reconstruct the secret key. Furthermore, secret key
extraction is demonstrated for the LBlock Feistel-type lightweight
block cipher.
Abstract: In this paper genetic based test data compression is
targeted for improving the compression ratio and for reducing the
computation time. The genetic algorithm is based on extended pattern
run-length coding. The test set contains a large number of X value
that can be effectively exploited to improve the test data
compression. In this coding method, a reference pattern is set and its
compatibility is checked. For this process, a genetic algorithm is
proposed to reduce the computation time of encoding algorithm. This
coding technique encodes the 2n compatible pattern or the inversely
compatible pattern into a single test data segment or multiple test data
segment. The experimental result shows that the compression ratio
and computation time is reduced.
Abstract: In this glasshouse study, we developed a new imagebased
non-destructive technique for detecting leaf P status of
different crops such as cotton, tomato and lettuce. The plants were
grown on a nutrient solution containing different P concentrations,
e.g. 0%, 50% and 100% of recommended P concentration (P0 = no P,
L; P1 = 2.5 mL 10 L-1 of P and P2 = 5 mL 10 L-1 of P). After 7 weeks
of treatment, the plants were harvested and data on leaf P contents
were collected using the standard destructive laboratory method and
at the same time leaf images were collected by a handheld crop image
sensor. We calculated leaf area, leaf perimeter and RGB (red, green
and blue) values of these images. These data were further used in
linear discriminant analysis (LDA) to estimate leaf P contents, which
successfully classified these plants on the basis of leaf P contents.
The data indicated that P deficiency in crop plants can be predicted
using leaf image and morphological data. Our proposed nondestructive
imaging method is precise in estimating P requirements of
different crop species.
Abstract: The aim of the study is to improve the understanding
of latent and sensible thermal energy storage within a paraffin wax
media by an array of cylindrical tubes arranged both in in-line and
staggered layouts. An analytical and experimental study is carried out
in a horizontal shell-and-tube type system during melting process.
Pertamina paraffin-wax was used as a phase change material (PCM),
while the tubes are embedded in the PCM. From analytical study we
can obtain the useful information in designing a thermal energy
storage such as: the motion of interface, amount of material melted at
any time in the process, and the heat storage characteristic during
melting. The use of staggered tubes is proposed compared to in-line
layout in a heat exchanger as thermal storage. The experimental study
is used to verify the validity of the analytical predictions. From the
comparisons, the analytical and experimental data are in a good
agreement.
Abstract: Introduction: The process to build a better safety
culture, methods of error analysis, and preventive measures, starts
with an understanding of the effects when human factors engineering
refer to remote microscopic diagnosis in surgery and specially in
organ transplantation for the remote evaluation of the grafts. It has
been estimated that even in well-organized transplant systems an
average of 8% to 14% of the grafts (G) that arrive at the recipient
hospitals may be considered as diseased, injured, damaged or
improper for transplantation. Digital microscopy adds information on
a microscopic level about the grafts in Organ Transplant (OT), and
may lead to a change in their management. Such a method will
reduce the possibility that a diseased G, will arrive at the recipient
hospital for implantation. Aim: Ergonomics of Digital Microscopy
(DM) based on virtual slides, on Telemedicine Systems (TS) for
Tele-Pathological (TPE) evaluation of the grafts (G) in organ
transplantation (OT). Material and Methods: By experimental
simulation, the ergonomics of DM for microscopic TPE of Renal
Graft (RG), Liver Graft (LG) and Pancreatic Graft (PG) tissues is
analyzed. In fact, this corresponded to the ergonomics of digital
microscopy for TPE in OT by applying Virtual Slide (VS) system for
graft tissue image capture, for remote diagnoses of possible
microscopic inflammatory and/or neoplastic lesions. Experimentation
included: a. Development of an OTE-TS similar Experimental
Telemedicine System (Exp.-TS), b. Simulation of the integration of
TS with the VS based microscopic TPE of RG, LG and PG applying
DM. Simulation of the DM based TPE was performed by 2
specialists on a total of 238 human Renal Graft (RG), 172 Liver Graft
(LG) and 108 Pancreatic Graft (PG) tissues digital microscopic
images for inflammatory and neoplastic lesions on four electronic
spaces of the four used TS. Results: Statistical analysis of specialist‘s
answers about the ability to diagnose accurately the diseased RG, LG
and PG tissues on the electronic space among four TS (A,B,C,D)
showed that DM on TS for TPE in OT is elaborated perfectly on the
ES of a Desktop, followed by the ES of the applied Exp.-TS. Tablet
and Mobile-Phone ES seem significantly risky for the application of
DM in OT (p
Abstract: Lateral torsional buckling is a global buckling mode
which should be considered in design of slender structural members
under flexure about their strong axis. It is possible to compute the
load which causes lateral torsional buckling of a beam by finite
element analysis, however, closed form equations are needed in
engineering practice for calculation ease which can be obtained by
using energy method. In lateral torsional buckling applications of
energy method, a proper function for the critical lateral torsional
buckling mode should be chosen which can be thought as the
variation of twisting angle along the buckled beam. Accuracy of the
results depends on how close is the chosen function to the exact
mode. Since critical lateral torsional buckling mode of the cantilever
I-beams varies due to material properties, section properties and
loading case, the hardest step is to determine a proper mode function
in application of energy method. This paper presents an approximate function for critical lateral
torsional buckling mode of doubly symmetric cantilever I-beams.
Coefficient matrices are calculated for concentrated load at free end,
uniformly distributed load and constant moment along the beam
cases. Critical lateral torsional buckling modes obtained by presented
function and exact solutions are compared. It is found that the modes
obtained by presented function coincide with differential equation
solutions for considered loading cases.
Abstract: In this study, a general approach to the reliability
based limit analysis of laterally loaded piles is presented. In
engineering practice the uncertainties play a very important role. The
aim of this study is to evaluate the lateral load capacity of free-head
and fixed-head long pile when plastic limit analysis is considered. In
addition to the plastic limit analysis to control the plastic behaviour
of the structure, uncertain bound on the complementary strain energy
of the residual forces is also applied. This bound has significant effect
for the load parameter. The solution to reliability-based problems is
obtained by a computer program which is governed by the reliability
index calculation.
Abstract: Obturator Foramen is a specific structure in Pelvic
bone images and recognition of it is a new concept in medical image
processing. Moreover, segmentation of bone structures such as
Obturator Foramen plays an essential role for clinical research in
orthopedics. In this paper, we present a novel method to analyze the
similarity between the substructures of the imaged region and a hand
drawn template as a preprocessing step for computation of Pelvic
bone rotation on hip radiographs. This method consists of integrated
usage of Marker-controlled Watershed segmentation and Zernike
moment feature descriptor and it is used to detect Obturator Foramen
accurately. Marker-controlled Watershed segmentation is applied to
separate Obturator Foramen from the background effectively. Then,
Zernike moment feature descriptor is used to provide matching
between binary template image and the segmented binary image for
final extraction of Obturator Foramens. Finally, Pelvic bone rotation
rate calculation for each hip radiograph is performed automatically to
select and eliminate hip radiographs for further studies which depend
on Pelvic bone angle measurements. The proposed method is tested
on randomly selected 100 hip radiographs. The experimental results
demonstrated that the proposed method is able to segment Obturator
Foramen with 96% accuracy.
Abstract: The aim of this paper is to analyze the impact of
literature review software on researchers. The aim of this study was
achieved by analyzing models in terms of perceived usefulness,
perceived ease of use, and acceptance level. Collected data were
analyzed using WarpPLS 4.0 software. This study used two
theoretical frameworks, namely, Technology Acceptance Model and
the Training Needs Assessment Model. The study was experimental
and was conducted at a public university in South Africa. The results
of the study showed that acceptance level has a high impact on
research productivity followed by perceived usefulness and perceived
ease of use.
Abstract: Cesium molybdates with general formula
CsMIII(MoO4)2, where MIII = Bi, Dy, Pr, Er, exhibit rich
polymorphism, and crystallize in a layered structure. These properties
cause intensive studies on cesium molybdates. CsBi(MoO4)2 was synthesized by microwave method by using
cerium sulphate, bismuth oxide and molybdenum (VI) oxide in an
appropriate molar ratio. Characterizations were done by x-ray
diffraction (XRD), fourier transform infrared (FTIR) spectroscopy,
scanning electron microscopy/energy dispersive analyze (SEM/EDS),
thermo gravimetric/differantial thermal analysis (TG/DTA).
Abstract: This paper presents a comparative analysis of
continuously stirred tank reactor (CSTR) control based on adaptive
control and optimal tuning of PID control based on particle swarm
optimization. In the design of adaptive control, Model reference
adaptive control (MRAC) scheme is used, in which the adaptation
law have been developed by MIT rule & Lyapunov’s rule. In PSO
control parameters of PID controller is tuned by using the concept of
particle swarm optimization to get optimized operating point for
minimum integral square error (ISE) condition. The results show the
adjustment of PID parameters converting into the optimal operating
point and the good control response can be obtained by the PSO
technique.
Abstract: Background: To compare the thinning patterns of the
ganglion cell-inner plexiform layer (GCIPL) and peripapillary retinal
nerve fiber layer (pRNFL) as measured using Cirrus high-definition
optical coherence tomography (HD-OCT) in patients with visual field
(VF) defects that respect the vertical meridian. Methods: Twenty eyes of eleven patients with VF defects that
respect the vertical meridian were enrolled retrospectively. The
thicknesses of the macular GCIPL and pRNFL were measured using
Cirrus HD-OCT. The 5% and 1% thinning area index (TAI) was
calculated as the proportion of abnormally thin sectors at the 5% and
1% probability level within the area corresponding to the affected VF.
The 5% and 1% TAI were compared between the GCIPL and pRNFL
measurements. Results: The color-coded GCIPL deviation map showed a
characteristic vertical thinning pattern of the GCIPL, which is also
seen in the VF of patients with brain lesions. The 5% and 1% TAI
were significantly higher in the GCIPL measurements than in the
pRNFL measurements (all P < 0.01). Conclusions: Macular GCIPL analysis clearly visualized a
characteristic topographic pattern of retinal ganglion cell (RGC) loss
in patients with VF defects that respect the vertical meridian, unlike
pRNFL measurements. Macular GCIPL measurements provide more
valuable information than pRNFL measurements for detecting the
loss of RGCs in patients with retrograde degeneration of the optic
nerve fibers.
Abstract: The goal of this paper is proposing a supply chain
value dashboard in home appliance manufacturing firms to create
more value for all stakeholders via balanced scorecard approach.
Balanced scorecard is an effective approach that managers have used
to evaluate supply chain performance in many fields but there is a
lack of enough attention to all supply chain stakeholders, improving
value creation and, defining correlation between value indicators and
performance measuring quantitatively. In this research the key
stakeholders in home appliance supply chain, value indicators with
respect to create more value for stakeholders and the most important
metrics to evaluate supply chain value performance based on
balanced scorecard approach have been selected via literature review.
The most important indicators based on expert’s judgment acquired
by in survey focused on creating more value for. Structural equation
modelling has been used to disclose relations between value
indicators and balanced scorecard metrics. The important result of
this research is identifying effective value dashboard to create more
value for all stakeholders in supply chain via balanced scorecard
approach and based on an empirical study covering ten home
appliance manufacturing firms in Iran. Home appliance
manufacturing firms can increase their stakeholder's satisfaction by
using this value dashboard.
Abstract: To study the dynamic mechanics response of asphalt
pavement under the temperature load and vehicle loading, asphalt
pavement was regarded as multilayered elastic half-space system, and
theory analysis was conducted by regarding dynamic modulus of
asphalt mixture as the parameter. Firstly, based on the dynamic
modulus test of asphalt mixture, function relationship between the
dynamic modulus of representative asphalt mixture and temperature
was obtained. In addition, the analytical solution for thermal stress in
single layer was derived by using Laplace integral transformation and
Hankel integral transformation respectively by using thermal
equations of equilibrium. The analytical solution of calculation model
of thermal stress in asphalt pavement was derived by transfer matrix
of thermal stress in multilayer elastic system. Finally, the variation of
thermal stress in pavement structure was analyzed. The result shows
that there is obvious difference between the thermal stress based on
dynamic modulus and the solution based on static modulus. So the
dynamic change of parameter in asphalt mixture should be taken into
consideration when theoretical analysis is taken out.