Abstract: This paper presents the findings of an experimental investigation of important machining parameters for the horizontal boring tool modified to mouth with a horizontal lathe machine to bore an overlength workpiece. In order to verify a usability of a modified tool, design of experiment based on Taguchi method is performed. The parameters investigated are spindle speed, feed rate, depth of cut and length of workpiece. Taguchi L9 orthogonal array is selected for four factors three level parameters in order to minimize surface roughness (Ra and Rz) of S45C steel tubes. Signal to noise ratio analysis and analysis of variance (ANOVA) is performed to study an effect of said parameters and to optimize the machine setting for best surface finish. The controlled factors with most effect are depth of cut, spindle speed, length of workpiece, and feed rate in order. The confirmation test is performed to test the optimal setting obtained from Taguchi method and the result is satisfactory.
Abstract: This paper deals with advanced state estimation algorithms for estimation of biomass concentration and specific growth rate in a typical fed-batch biotechnological process. This biotechnological process was represented by a nonlinear mass-balance based process model. Extended Kalman Filter (EKF) and Particle Filter (PF) was used to estimate the unmeasured state variables from oxygen uptake rate (OUR) and base consumption (BC) measurements. To obtain more general results, a simplified process model was involved in EKF and PF estimation algorithms. This model doesn’t require any special growth kinetic equations and could be applied for state estimation in various bioprocesses. The focus of this investigation was concentrated on the comparison of the estimation quality of the EKF and PF estimators by applying different measurement noises. The simulation results show that Particle Filter algorithm requires significantly more computation time for state estimation but gives lower estimation errors both for biomass concentration and specific growth rate. Also the tuning procedure for Particle Filter is simpler than for EKF. Consequently, Particle Filter should be preferred in real applications, especially for monitoring of industrial bioprocesses where the simplified implementation procedures are always desirable.
Abstract: In recent years in Italy the progress of the automobile industry, in the field of reduction of emissions values, is very remarkable. Nevertheless their evaluation and reduction is a key problem, especially in the cities, that account for more than 50% of world population. In this paper we dealt with the problem of describing a quantitatively approach for the reconstruction of GPS coordinates and altitude, in the context of correlation study between driving cycles / emission / geographical location, during an experimental campaign realized with some instrumented cars.
Abstract: Bangnoi Floating Market located at Bangkhonthi
Districts Samut Songkhram Province is a valuable architectural
market. The lifestyle of the community's relationship with the living
space and the relationship between the architectural style of the area's
residential waterfront communities of Bangnoi Floating Bangkhonthi
Districts Samut Songkhram Province, which deserves to be
preserved.
Therefore, this research it helps to know the value of the
architectural style of the area's residential waterfront communities of
Bangnoi Floating Bangkhonthi Districts SamutSongkhram Province,
which deserves to be preserved.
Abstract: The objectives of the research are to study patterns of fire location distribution and develop techniques of Geographic Information System application in fire risk assessment for fire planning and management. Fire risk assessment was based on two factors: the vulnerability factor such as building material types, building height, building density and capacity for mitigation factor such as accessibility by road, distance to fire station, distance to hydrants and it was obtained from four groups of stakeholders including firemen, city planners, local government officers and local residents. Factors obtained from all stakeholders were converted into Raster data of GIS and then were superimposed on the data in order to prepare fire risk map of the area showing level of fire risk ranging from high to low. The level of fire risk was obtained from weighted mean of each factor based on the stakeholders. Weighted mean for each factor was obtained by Analytical Hierarchy Analysis.
Abstract: Emotional Intelligence (EI) has been identified as an
important factor for corporate success. However, there are few
empirical findings on the impact of Strategic EI per se. The ooverall
objective of the study was to empirically examine the relationship
between the Strategic EI and Transformational Leadership style of
managers. Sixty four managers were selected from the banking
industry in Czech Republic. Genos EI Inventory, and the Multifactor
Leadership Questionnaire – Form 5X-Short were employed as the
major research instruments of the study. Descriptive and inferential
analyses of survey data were conducted using SPSS software.
Variations were observed among the components of Strategic EI
between males, and females. Study concludes positive a relationship
between Strategic EI of Czech managers and their transformational
leadership style. Improving awareness and usage of EI, will
contribute to facilitate career success through enhanced levels of
transformational leadership of managers.
Abstract: A continuous time model of the interaction between
crop insect pests and naturally beneficial pest enemies is created
using a set of simultaneous, non-linear, ordinary differential
equations incorporating natural death rates based on the Weibull
distribution. The crop pest is present in all its life-cycle stages of:
egg, larva, pupa and adult. The beneficial insects, parasitoid wasps,
may be present in either or all parasitized: eggs, larva and pupa.
Population modelling is used to estimate the quantity of the natural
pest enemies that should be introduced into the pest infested
environment to suppress the pest population density to an
economically acceptable level within a prescribed number of days.
The results obtained illustrate the effect of different combinations of
parasitoid wasps, using the Pascal distribution to estimate their
success in parasitizing different pest developmental stages, to deliver
pest control to a sustainable level. Effective control, within a
prescribed number of days, is established by the deployment of two
or all three species of wasps, which partially destroy pest: egg, larvae
and pupae stages. The selected scenarios demonstrate effective
sustainable control of the pest in less than thirty days.
Abstract: The paper gives basic information on application of
rotation bending for manufacturing ship hull parts from steel plates
and on MGPS machines, employed for this purpose.
Abstract: This research analyzes factors affecting the success of Bitcoin Value within Thailand and develops a guideline for self-reliance for effective business implementation. Samples in this study included 121 people through surveys. The results revealed four main factors affecting the success as follows: 1) A great majority didn't know what Bitcoin was. 2) Didn't grasp the concept of a digital currency or see the benefit of a digital currency. 3) There is a great need to educate the next generation of learners on the benefits of Bitcoin within the community. 4) Future Career training should be pursued in applied Bitcoin development.
The guideline for self-reliance planning consisted of 4 aspects: 1) Local communities need to develop awareness of the usefulness of Bitcoin and share the value of Bitcoin among friends and family. 2) Computer Science and Business Management staff should develop skills to expand on the benefits of Bitcoin within their departments. 3) Further research should be pursued on how Bitcoin Value can improve business and tourism within Thailand. Local communities should focus on developing Bitcoin awareness by encouraging street vendors to accept Bitcoin as another form of payment for services rendered. 4) Development planning: by arranging meet up groups to conduct further education on Bitcoin and share solutions on adoption into every day usage.
Abstract: This study has only one objective which is to identify the different in factors of choosing the distributor for food and non-food OTOP entrepreneur in Thailand. In this research, the types of OTOP product will be divided into two groups which are food and non-food. The sample for the food type OTOP product was the processed fruit and vegetable from Nakorn Pathom province and the sample for the non-food type OTOP product was the court doll from Ang Thong province. The research was divided into 3 parts which were a study of the distribution pattern and how to choose the distributor of the food type OTOP product, a study of the distribution pattern and how to choose the distributor of the non-food type OTOP product and a comparison between 2 types of products to find the differentiation in the factor of choosing distributor. The data and information was collected by using the interview. The populations in the research were 5 producers of the processed fruit and vegetable from Nakorn Pathom province and 5 producers of the court doll from Ang Thong province. The significant factor in choosing the distributor of the food type OTOP product is the material handling efficiency and on-time delivery but for the non-food type OTOP product is focused on the channel of distribution and cost of the distributor.
Abstract: In the past, the most comprehensively adopted light
source was incandescent light bulbs, but with the appearance of LED
light sources, traditional light sources have been gradually replaced by
LEDs because of its numerous superior characteristics. However,
many of the standards do not apply to LEDs as the two light sources
are characterized differently. This also intensifies the significance of
studies on LEDs. As a Kansei design study investigating the visual
glare produced by traffic arrows implemented with LEDs, this study
conducted a semantic analysis on the styles of traffic arrows used in
domestic and international occasions. The results will be able to
reduce drivers’ misrecognition that results in the unsuccessful arrival
at the destination, or in traffic accidents. This study started with a
literature review and surveyed the status quo before conducting
experiments that were divided in two parts. The first part involved a
screening experiment of arrow samples, where cluster analysis was
conducted to choose five representative samples of LED displays. The
second part was a semantic experiment on the display of arrows using
LEDs, where the five representative samples and the selected ten
adjectives were incorporated. Analyzing the results with
Quantification Theory Type I, it was found that among the
composition of arrows, fletching was the most significant factor that
influenced the adjectives. In contrast, a “no fletching” design was
more abstract and vague. It lacked the ability to convey the intended
message and might bear psychological negative connotation including
“dangerous,” “forbidden,” and “unreliable.” The arrow design
consisting of “> shaped fletching” was found to be more concrete and
definite, showing positive connotation including “safe,” “cautious,”
and “reliable.” When a stimulus was placed at a farther distance, the
glare could be significantly reduced; moreover, the visual evaluation
scores would be higher. On the contrary, if the fletching and the shaft
had a similar proportion, looking at the stimuli caused higher
evaluation at a closer distance. The above results will be able to be
applied to the design of traffic arrows by conveying information
definitely and rapidly. In addition, drivers’ safety could be enhanced
by understanding the cause of glare and improving visual
recognizability.
Abstract: Virtual reality (VR) is a rapidly emerging computer
interface that attempts to immerse the user completely within an
experimental recreation; thereby, greatly enhancing the overall
impact and providing a much more intuitive link between the
computer and the human participants. The main objective of this
study is to design tractor trailer capable of meeting the customers’
requirements and suitable for rough conditions to be used in
combination with a farm tractor in India. The final concept is capable
of providing arrangements for attaching the trailer to the tractor easily
by pickup hitch, stronger and lighter supporting frame, option of
spare tyre etc. Furthermore, the resulting product design can be sent
via the Internet to customers for comments or marketing purposes.
The virtual prototyping (VP) system therefore facilitates advanced
product design and helps reduce product development time and cost
significantly.
Abstract: The high efficiency power management IC (PMIC) with switching device is presented in this paper. PMIC is controlled with PFM control method in order to have high power efficiency at high current level. Dynamic Threshold voltage CMOS (DT-CMOS) with low on-resistance is designed to decrease conduction loss. The threshold voltage of DT-CMOS drops as the gate voltage increase, resulting in a much higher current handling capability than standard MOSFET. PFM control circuits consist of a generator, AND gate and comparator. The generator is made to have 1.2MHz oscillation voltage. The DC-DC converter based on PFM control circuit and low on-resistance switching device is presented in this paper.
Abstract: Compost can influence soil fertility and plant health. At the same time compost can play an important role in the nitrogen cycle and it can influence leaching of mineral nitrogen from soil to underground water.
This paper deals with the influence of compost addition and mineral nitrogen fertilizer on leaching of mineral nitrogen, nitrogen availability in microbial biomass and plant biomass production in the lysimetric experiment. Twenty one lysimeters were filed with topsoil and subsoil collected in the area of protection zone of underground source of drinking water - Březová nad Svitavou. The highest leaching of mineral nitrogen was detected in the variant fertilized only mineral nitrogen fertilizer (624.58 mg m-2), the lowest leaching was recorded in the variant with high addition of compost (315.51 mg m-2). On the other hand, losses of mineral nitrogen are not in connection with the losses of available form of nitrogen in microbial biomass. Because lost of mineral nitrogen was detected in variant with the least change in the availability of N in microbial biomass.
The leaching of mineral nitrogen, yields as well as the results concerning nitrogen availability from the first year of long term experiment suggest that compost can positive influence the leaching of nitrogen into underground water.
Abstract: In this paper, we propose a method that allows faster and more accurate detection of traffic lights by a vision sensor during driving, DGPS is used to obtain physical location of a traffic light, extract from the image information of the vision sensor only the traffic light area at this location and ascertain if the sign is in operation and determine its form. This method can solve the problem in existing research where low visibility at night or reflection under bright light makes it difficult to recognize the form of traffic light, thus making driving unstable. We compared our success rate of traffic light recognition in day and night road environments. Compared to previous researches, it showed similar performance during the day but 50% improvement at night.
Abstract: Today, the means of following the developments in
the area of science and technology is to keep up with the pace of the
advancements in this area. As is in every profession, apart from their
personal efforts, the training of teachers in the period after they start
their careers is only possible through in-service training. The aim of
the present study is to determine the views of Information
Technologies (IT) teachers regarding the in-service training courses
organized by the Ministry of National Education. In this study, in
which quantitative research methods and techniques were employed,
the views of 196 IT teachers were collected by using the “Views on
In-service Training” questionnaire developed by the authors of the
paper. Independent groups t-test was used to determine whether the
views of IT teachers regarding in-service training differed depending
on gender, age and professional seniority. One-way analysis of
variance (ANOVA) was used to investigate whether the views of IT
teachers regarding in-service training differed depending on the
number of in-service training courses they joined and the type of inservice
training course they wanted to take. According to the findings
obtained in the study, the views of IT teachers on in-service training
did not show a significant difference depending on gender and age,
whereas those views differed depending on professional seniority, the
number of in-service training courses they joined and the type of inservice
training course they wanted to take.
Abstract: The objective is to study the satisfaction on English with an online learning. Online learning system mainly consists of English lessons, exercises, tests, web boards, and supplementary lessons for language practice. The sample groups are 80 Thai students studying English for Business Communication, majoring in Hotel and Lodging Management. The data are analyzed by mean, standard deviation (S.D.) value from the questionnaires. The results were found that the most average of satisfaction on academic aspects are technological searching tool through E-learning system that support the students’ learning (4.51), knowledge evaluation on pre-post learning and teaching (4.45), and change for project selections according to their interest, subject contents including practice in the real situations (4.45), respectively.
Abstract: This research aims to study the level of democratic political culture and the factors that affect the democratic political culture of 5th and 6th graders under the authority of Dusit District Office, Bangkok by using stratified sampling for probability sampling and using purposive sampling for non-probability sampling to collect data toward the distribution of questionnaires to 300 respondents. This covers all of the schools under the authority of Dusit District Office. The researcher analyzed the data by using descriptive statistics which include arithmetic mean, standard deviation, and inferential statistics which are Independent Samples T-test (T-test) and One-Way ANOVA (F-test). The researcher also collected data by interviewing the target groups, and then analyzed the data by the use of descriptive analysis. The result shows that 5th and 6th graders under the authority of Dusit District Office, Bangkok have exposed to democratic political culture at high level in overall. When considering each part, it found out that the part that has highest mean is “the constitutional democratic governmental system is suitable for Thailand” statement. The part with the lowest mean is “corruption (cheat and defraud) is normal in Thai society” statement. The factor that affects democratic political culture is grade levels, occupations of mothers, and attention in news and political movements.
Abstract: The objectives were to study language learning strategies (LLSs) employed by Chinese students, and the frequency of LLSs they used, and examine the relationship between the use of LLSs and gender. The Strategy Inventory for Language Learning (SILL) by Oxford was administered to thirty-six Chinese students at Suan Sunandha Rajabhat University in Thailand. The data obtained was analyzed using descriptive statistics and chi-square tests. Three useful findings were found on the use of LLSs reported by Chinese students. First, Chinese students used overall LLSs at a high level. Second, among the six strategy groups, Chinese students employed compensation strategy most frequently and memory strategy least frequently. Third, the research results also revealed that gender had significant effect on Chinese Student’s use of overall LLSs.
Abstract: This paper presents a neural network based model predictive control (MPC) strategy to control a strongly exothermic reaction with complicated nonlinear kinetics given by Chylla-Haase polymerization reactor that requires a very precise temperature control to maintain product uniformity. In the benchmark scenario, the operation of the reactor must be guaranteed under various disturbing influences, e.g., changing ambient temperatures or impurity of the monomer. Such a process usually controlled by conventional cascade control, it provides a robust operation, but often lacks accuracy concerning the required strict temperature tolerances. The predictive control strategy based on the RBF neural model is applied to solve this problem to achieve set-point tracking of the reactor temperature against disturbances. The result shows that the RBF based model predictive control gives reliable result in the presence of some disturbances and keeps the reactor temperature within a tight tolerance range around the desired reaction temperature.