Abstract: The use of electronic sensors in the electronics
industry has become increasingly popular over the past few years,
and it has become a high competition product. The frequency
adjustment process is regarded as one of the most important process
in the electronic sensor manufacturing process. Due to inaccuracies
in the frequency adjustment process, up to 80% waste can be caused
due to rework processes; therefore, this study aims to provide a
preliminary understanding of the role of parameters used in the
frequency adjustment process, and also make suggestions in order to
further improve performance. Four parameters are considered in this
study: air pressure, dispensing time, vacuum force, and the distance
between the needle tip and the product. A full factorial design for
experiment 2k was considered to determine those parameters that
significantly affect the accuracy of the frequency adjustment process,
where a deviation in the frequency after adjustment and the target
frequency is expected to be 0 kHz. The experiment was conducted on
two levels, using two replications and with five center-points added.
In total, 37 experiments were carried out. The results reveal that air
pressure and dispensing time significantly affect the frequency
adjustment process. The mathematical relationship between these
two parameters was formulated, and the optimal parameters for air
pressure and dispensing time were found to be 0.45 MPa and 458 ms,
respectively. The optimal parameters were examined by carrying out
a confirmation experiment in which an average deviation of 0.082
kHz was achieved.
Abstract: The Proton Exchange Membrane Fuel Cell (PEMFC)
control system has an important effect on operation of cell.
Traditional controllers couldn-t lead to acceptable responses because
of time- change, long- hysteresis, uncertainty, strong- coupling and
nonlinear characteristics of PEMFCs, so an intelligent or adaptive
controller is needed. In this paper a neural network predictive
controller have been designed to control the voltage of at the
presence of fluctuations of temperature. The results of
implementation of this designed NN Predictive controller on a
dynamic electrochemical model of a small size 5 KW, PEM fuel cell
have been simulated by MATLAB/SIMULINK.
Abstract: The purposes of this study were as follows to evaluate
the economic value of Phu Kradueng National Park by the travel cost
method (TCM) and the contingent valuation method (CVM) and to
estimate the demand for traveling and the willingness to pay. The
data for this study were collected by conducting two large scale
surveys on users and non-users. A total of 1,016 users and 1,034
non-users were interviewed. The data were analyzed using multiple
linear regression analysis, logistic regression model and the
consumer surplus (CS) was the integral of demand function for trips.
The survey found, were as follows:
1)Using the travel cost method which provides an estimate of direct
benefits to park users, we found that visitors- total willingness to pay
per visit was 2,284.57 bath, of which 958.29 bath was travel cost,
1,129.82 bath was expenditure for accommodation, food, and
services, and 166.66 bath was consumer surplus or the visitors -net
gain or satisfaction from the visit (the integral of demand function for
trips).
2) Thai visitors to Phu Kradueng National Park were further willing
to pay an average of 646.84 bath per head per year to ensure the
continued existence of Phu Kradueng National Park and to preserve
their option to use it in the future.
3) Thai non-visitors, on the other hand, are willing to pay an average
of 212.61 bath per head per year for the option and existence value
provided by the Park.
4) The total economic value of Phu Kradueng National Park to Thai
visitors and non-visitors taken together stands today at 9,249.55
million bath per year.
5) The users- average willingness to pay for access to Phu Kradueng
National Park rises
from 40 bath to 84.66 bath per head per trip for improved services
such as road improvement, increased cleanliness, and upgraded
information.
This paper was needed to investigate of the potential market
demand for bio prospecting in Phu Kradueng national Park and to
investigate how a larger share of the economic benefits of tourism
could be distributed income to the local residents.
Abstract: Currently, the demand for marine and fisheries commodity in Yogyakarta, Indonesia continues to increase. The existing condition shows that the aquaculture supply cannot be supplied by Yogyakarta region itself, but still need to be supported by regions outside Yogyakarta. The effort to optimize the market is initiated by reviewing and designing the supply chain of production and trade of aquaculture commodity in order to create the implementation of aquaculture production and trade commodity optimally. This formulated supply chain model indicates 4 performance indicators of measurable success in terms of: (1) efficiency; (2) flexibility; (3) responsiveness; and (4) quality. These indicators had been exercised as the success benchmarks for priority marketing management in local level as well as national level. The result of this research indicates that if the catfish fishery system is managed as business as usual then the catfish demand in Yogyakarta region will experience to increase in the future. The increase of demand is inline with the increase of number of people in Yogyakarta and also the fluctuation of catfish consumption per capita. The highest production of catfish will experience in the third year approximately 30,118 tons. Other result of the research indicates that the catfish demand in Yogyakarta region cannot be supplied yet from the local region. Therefore, to fulfill the supply from outside Yogyakarta region, the local farmers should improve the supply through land extension. The fluctuation of commodity price will experience in the future annually and the catfish supply from outside Yogyakarta region will be lowering the price in the market.
Abstract: Groundwater resources in Arsanjan plain provide
water for agriculture, industry, and human consumption. Continued
agricultural development in this area needs to additional groundwater
resources for, particularly during of drought periods, and effects on
the quantity and quality of ground water available. The purpose of
this study is to evaluate water level changes in the aquifer of
Arsanjan plain in the Fars province in order to determine the areas of
greatest depletion and the causes of depletion. In this plain, farmers
and other users are pumping groundwater faster than its natural
replenishment rate, causing a continuous drop in groundwater tables
and depletion of this resource. In this research variation of
groundwater level, their effects and ways to help control groundwater
levels in aquifer of the Arsanjan plains were evaluated .Excessive
exploitation of groundwater in this aquifer caused the groundwater
levels fall too fast or to unacceptable levels. The average drawdown
of the groundwater level in this plain were 19.66 meters during
1996 to 2003.
Abstract: In order to improve the simulation effects of space cold
black environment, this paper described a rectangular channel plate
heat sink. By using fluid mechanics theory and finite element method,
the internal fluid flow and heat transfer in heat sink was numerically
simulated to analyze the impact of channel structural on fluid flow and
heat transfer. The result showed that heat sink temperature uniformity
is well, and the impact of channel structural on the heat sink
temperature uniformity is not significant. The channel depth and
spacing are important factors which affect the fluid flow and heat
transfer in the heat sink. The two factors of heat transfer and resistance
need to be considered comprehensively to determine the optimal flow
structure parameters.
Abstract: Biological, psychological and social experiences and
perceptions of healthcare services in patients medically diagnosed of
coronary heart disease were investigated using a sample of 10
participants whose responses to the in-depth interview questions
were analyzed based on inter-and-intra-case analyses. The results
obtained revealed that advancing age, single status, divorce and/or
death of spouse and the issue of single parenting negatively impacted
patients- biopsychosocial experiences. The patients- experiences of
physical signs and symptoms, anxiety and depression, past serious
medical conditions, use of self-prescribed medications, family
history of poor mental/medical or physical health, nutritional
problems and insufficient physical activities heightened their risk of
coronary attack. Collectivist culture served as a big source of relieve
to the patients. Patients- temperament, experience of different
chronic life stresses/challenges, mood alteration, regular drinking,
smoking/gambling, and family/social impairments compounded their
health situation. Patients were satisfied with the biomedical services
rendered by the healthcare personnel, whereas their psychological
and social needs were not attended to. Effective procedural treatment
model, a holistic and multidimensional approach to the treatment of
heart disease patients was proposed.
Abstract: A good green building design project, designers should consider not only energy consumption, but also healthy and comfortable needs of inhabitants. In recent years, the Taiwan government paid attentions on both carbon reduction and indoor air quality issues, which be presented in the legislation of Building Codes and other regulations. Taiwan located in hot and humid climates, dampness in buildings leads to significant microbial pollution and building damage. This means that the high temperature and humidity present a serious indoor air quality issue. The interactions between vapor transfers and energy fluxes are essential for the whole building Heat Air and Moisture (HAM) response. However, a simulation tool with short calculation time, property accuracy and interface is needed for practical building design processes. In this research, we consider the vapor transfer phenomenon of building materials as well as temperature and humidity and energy consumption in a building space. The simulation bases on the EMPD method, which was performed by EnergyPlus, a simulation tool developed by DOE, to simulate the indoor moisture variation in a one-zone residential unit based on the Effective Moisture Penetration Depth Method, which is more suitable for practical building design processes.
Abstract: Carbon nanotubes (CNTs) possess unique structural,
mechanical, thermal and electronic properties, and have been
proposed to be used for applications in many fields. However, to
reach the full potential of the CNTs, many problems still need to be
solved, including the development of an easy and effective
purification procedure, since synthesized CNTs contain impurities,
such as amorphous carbon, carbon nanoparticles and metal particles.
Different purification methods yield different CNT characteristics
and may be suitable for the production of different types of CNTs. In
this study, the effect of different purification chemicals on carbon
nanotube quality was investigated. CNTs were firstly synthesized by
chemical vapor deposition (CVD) of acetylene (C2H2) on a
magnesium oxide (MgO) powder impregnated with an iron nitrate
(Fe(NO3)3·9H2O) solution. The synthesis parameters were selected
as: the synthesis temperature of 800°C, the iron content in the
precursor of 5% and the synthesis time of 30 min. The liquid phase
oxidation method was applied for the purification of the synthesized
CNT materials. Three different acid chemicals (HNO3, H2SO4, and
HCl) were used in the removal of the metal catalysts from the
synthesized CNT material to investigate the possible effects of each
acid solution to the purification step. Purification experiments were
carried out at two different temperatures (75 and 120 °C), two
different acid concentrations (3 and 6 M) and for three different time
intervals (6, 8 and 15 h). A 30% H2O2 : 3M HCl (1:1 v%) solution
was also used in the purification step to remove both the metal
catalysts and the amorphous carbon. The purifications using this
solution were performed at the temperature of 75°C for 8 hours.
Purification efficiencies at different conditions were evaluated by
thermogravimetric analysis. Thermal and electrical properties of
CNTs were also determined. It was found that the obtained electrical
conductivity values for the carbon nanotubes were typical for organic
semiconductor materials and thermal stabilities were changed
depending on the purification chemicals.
Abstract: Understanding of how and where NOx formation
occurs in industrial burner is very important for efficient and clean
operation of utility burners. Also the importance of this problem is
mainly due to its relation to the pollutants produced by more burners
used widely of gas turbine in thermal power plants and glass and steel
industry.
In this article, a numerical model of an industrial burner operating
in MILD combustion is validated with experimental data.. Then
influence of air flow rate and air temperature on combustor
temperature profiles and NOX product are investigated. In order to
modification this study reports on the effects of fuel and air dilution
(with inert gases H2O, CO2, N2), and also influence of lean-premixed
of fuel, on the temperature profiles and NOX emission.
Conservation equations of mass, momentum and energy, and
transport equations of species concentrations, turbulence, combustion
and radiation modeling in addition to NO modeling equations were
solved together to present temperature and NO distribution inside the
burner.
The results shows that dilution, cause to a reduction in value of
temperature and NOX emission, and suppresses any flame
propagation inside the furnace and made the flame inside the furnace
invisible. Dilution with H2O rather than N2 and CO2 decreases further
the value of the NOX. Also with raise of lean-premix level, local
temperature of burner and the value of NOX product are decreases
because of premixing prevents local “hot spots" within the combustor
volume that can lead to significant NOx formation. Also leanpremixing
of fuel with air cause to amount of air in reaction zone is
reach more than amount that supplied as is actually needed to burn
the fuel and this act lead to limiting NOx formation
Abstract: Walking and sit to stand are activities carried out by
all the people many times during the day, but physical disabilities due
to age and diseases create needs of assistive devices to help elderly
people during their daily life. This study aims to study the different
types and mechanisms of the assistive devices. We will analyze the
limitations and the challenges faced by the researchers in this field.
We will introduce the Assistive Device developed at the Egypt-Japan
University of Science and Technology, named E-JUST Assistive
Device (EJAD). EJAD will be a low cost intelligent assistive device
to help elders in walking and sit-to-stand activities.
Abstract: Very Large and/or computationally complex optimization problems sometimes require parallel or highperformance computing for achieving a reasonable time for computation. One of the most popular and most complicate problems of this family is “Traveling Salesman Problem". In this paper we have introduced a Branch & Bound based algorithm for the solution of such complicated problems. The main focus of the algorithm is to solve the “symmetric traveling salesman problem". We reviewed some of already available algorithms and felt that there is need of new algorithm which should give optimal solution or near to the optimal solution. On the basis of the use of logarithmic sampling, it was found that the proposed algorithm produced a relatively optimal solution for the problem and results excellent performance as compared with the traditional algorithms of this series.
Abstract: Due to important issues, such as deadlock, starvation,
communication, non-deterministic behavior and synchronization,
concurrent systems are very complex, sensitive, and error-prone.
Thus ensuring reliability and accuracy of these systems is very
essential. Therefore, there has been a big interest in the formal
specification of concurrent programs in recent years. Nevertheless,
some features of concurrent systems, such as dynamic process
creation, scheduling and starvation have not been specified formally
yet. Also, some other features have been specified partially and/or
have been described using a combination of several different
formalisms and methods whose integration needs too much effort. In
other words, a comprehensive and integrated specification that could
cover all aspects of concurrent systems has not been provided yet.
Thus, this paper makes two major contributions: firstly, it provides a
comprehensive formal framework to specify all well-known features
of concurrent systems. Secondly, it provides an integrated
specification of these features by using just a single formal notation,
i.e., the Z language.
Abstract: This paper presents a novel method for remaining
useful life prediction using the Elliptical Basis Function (EBF)
network and a Markov chain. The EBF structure is trained by a
modified Expectation-Maximization (EM) algorithm in order to take
into account the missing covariate set. No explicit extrapolation is
needed for internal covariates while a Markov chain is constructed to
represent the evolution of external covariates in the study. The
estimated external and the unknown internal covariates constitute an
incomplete covariate set which are then used and analyzed by the EBF
network to provide survival information of the asset. It is shown in the
case study that the method slightly underestimates the remaining
useful life of an asset which is a desirable result for early maintenance
decision and resource planning.
Abstract: Within the new world order, the term “crisis" is nowadays familiar to companies. Organizations are experiencing conditions which are surprising, uncertain, often adverse and usually unstable. The companies, who grasp the importance of transformation within the information age, have felt the need to develop modern methods to achieve the ability to thrive despite severe shocks. Through strategically managing human resource and developing appropriate elements of human resource system, companies can be assured for resolving the crisis. In this paper the role of HR system on resolving crisis has been evaluated. To help accomplish this, an insight on previous strategic HRM literature and an introduction to the elements and relationship within HR systems has been presented. It also reviews different attitude around resilience in literature. It continues by reviewing three elements central to developing an organization-s capacity for crisis resolving and it will demonstrate how designing proper elements of HR system can lead the organizations to possess the ability for passing through crisis. Finally it will evaluate an Iranian Insurance organization in case of one of the three central elements (specific cognitive ability) and observe how successful they were on developing an effective HR system to be ready for facing crisis.
Abstract: Increasing demand on the performance of Subsea
Production Systems (SPS) suggests a need for more detailed
investigation of fluid behavior taking place in subsea equipment.
Complete CFD cool down analyses of subsea equipment are very
time demanding. The objective of this paper is to investigate a
Locked CFD approach, which enables significant reduction of the
computational time and at the same time maintains sufficient
accuracy during thermal cool down simulations. The result
comparison of a dead leg simulation using the Full CFD and the three
LCFD-methods confirms the validity of the locked flow field
assumption for the selected case. For the tested case the LCFD
simulation speed up by factor of 200 results in the absolute thermal
error of 0.5 °C (3% relative error), speed up by factor of 10 keeps the
LCFD results within 0.1 °C (0.5 % relative error) comparing to the
Full CFD.
Abstract: The aim of study was to evaluate pressure distribution characteristics of the elastic textile bandages using two instrumental techniques: a prototype Instrument and a load Transference. The prototype instrument which simulates shape of real leg has pressure sensors which measure bandage pressure. Using this instrument, the results show that elastic textile bandages presents different pressure distribution characteristics and none produces a uniform distribution around lower limb.
The load transference test procedure is used to determine whether a relationship exists between elastic textile bandage structure and pressure distribution characteristics. The test procedure assesses degree of load, directly transferred through a textile when loads series are applied to bandaging surface. A range of weave fabrics was produced using needle weaving machine and a sewing technique. A textile bandage was developed with optimal characteristics far superior pressure distribution than other bandages. From results, we find that theoretical pressure is not consistent exactly with practical pressure. It is important in this study to make a practical application for specialized nurses in order to verify the results and draw useful conclusions for predicting the use of this type of elastic band.
Abstract: A lot of Scientific and Engineering problems require the solution of large systems of linear equations of the form bAx in an effective manner. LU-Decomposition offers good choices for solving this problem. Our approach is to find the lower bound of processing elements needed for this purpose. Here is used the so called Omega calculus, as a computational method for solving problems via their corresponding Diophantine relation. From the corresponding algorithm is formed a system of linear diophantine equalities using the domain of computation which is given by the set of lattice points inside the polyhedron. Then is run the Mathematica program DiophantineGF.m. This program calculates the generating function from which is possible to find the number of solutions to the system of Diophantine equalities, which in fact gives the lower bound for the number of processors needed for the corresponding algorithm. There is given a mathematical explanation of the problem as well. Keywordsgenerating function, lattice points in polyhedron, lower bound of processor elements, system of Diophantine equationsand : calculus.
Abstract: There are many issues that affect modeling and designing real-time databases. One of those issues is maintaining consistency between the actual state of the real-time object of the external environment and its images as reflected by all its replicas distributed over multiple nodes. The need to improve the scalability is another important issue. In this paper, we present a general framework to design a replicated real-time database for small to medium scale systems and maintain all timing constrains. In order to extend the idea for modeling a large scale database, we present a general outline that consider improving the scalability by using an existing static segmentation algorithm applied on the whole database, with the intent to lower the degree of replication, enables segments to have individual degrees of replication with the purpose of avoiding excessive resource usage, which all together contribute in solving the scalability problem for DRTDBS.
Abstract: Increasing concerns over climate change have limited
the liberal usage of available energy technology options. India faces
a formidable challenge to meet its energy needs and provide adequate
energy of desired quality in various forms to users in sustainable
manner at reasonable costs. In this paper, work carried out with an
objective to study the role of various energy technology options
under different scenarios namely base line scenario, high nuclear
scenario, high renewable scenario, low growth and high growth rate
scenario. The study has been carried out using Model for Energy
Supply Strategy Alternatives and their General Environmental
Impacts (MESSAGE) model which evaluates the alternative energy
supply strategies with user defined constraints on fuel availability,
environmental regulations etc. The projected electricity demand, at
the end of study period i.e. 2035 is 500490 MWYr. The model
predicted the share of the demand by Thermal: 428170 MWYr,
Hydro: 40320 MWYr, Nuclear: 14000 MWYr, Wind: 18000 MWYr
in the base line scenario. Coal remains the dominant fuel for
production of electricity during the study period. However, the
import dependency of coal increased during the study period. In
baseline scenario the cumulative carbon dioxide emissions upto 2035
are about 11,000 million tones of CO2. In the scenario of high nuclear
capacity the carbon dioxide emissions reduced by 10 % when nuclear
energy share increased to 9 % compared to 3 % in baseline scenario.
Similarly aggressive use of renewables reduces 4 % of carbon
dioxide emissions.