Abstract: The prepreg process among the CFRP (Carbon Fiber
Reinforced Plastic) forming methods is the short term of
‘Pre-impregnation’, which is widely used for aerospace composites
that require a high quality property such as a fiber-reinforced woven
fabric, in which an epoxy hardening resin is impregnated the reality.
However, that this process requires continuous researches and
developments for its commercialization because the delamination
characteristically develops between the layers when a great weight is
loaded from outside to supplement such demerit, three lamination
methods among the prepreg lamination methods of CFRP were
designed to minimize the delamination between the layers due to
external impacts. Further, the newly designed methods and the
existing lamination methods were analyzed through a mechanical
characteristic test, Interlaminar Shear Strength test. The Interlaminar
Shear Strength test result confirmed that the newly proposed three
lamination methods, i.e. the Roll, Half and Zigzag laminations,
presented more excellent strengths compared to the conventional Ply
lamination. The interlaminar shear strength in the roll method with
relatively dense fiber distribution was approximately 1.75% higher
than that in the existing ply lamination method, and in the half method,
it was approximately 0.78% higher.
Abstract: In this paper, the electromagnetic shielding
characteristics of an up-to-date typical carbon filler material, carbon
fiber used with a metal mesh were investigated. Carbon fiber
12k-prepregs, where carbon fibers were impregnated with epoxy, were
laminated with wire meshes, vacuum bag-molded and hardened to
manufacture hybrid-type specimens, with which an electromagnetic
shield test was performed in accordance with ASTM D4935-10,
through which was known as the most excellent reproducibility is
obtainable among electromagnetic shield tests. In addition, glass fiber
prepregs whose electromagnetic shielding effect were known as
insignificant were laminated and formed with wire meshes to verify
the validity of the electromagnetic shield effect of wire meshes in
order to confirm the electromagnetic shielding effect of metal meshes
corresponding existing carbon fiber 12k-prepregs. By grafting carbon
fibers, on which studies are being actively underway in the
environmental aspects and electromagnetic shielding effect, with
hybrid-type wire meshes that were analysed through the tests, in this
study, the applicability and possibility are proposed.
Abstract: The development, operation and maintenance of
Integrated Waste Management Systems (IWMS) affects essentially
the sustainable concern of every region. The features of such systems
have great influence on all of the components of sustainability. In
order to reach the optimal way of processes, a comprehensive
mapping of the variables affecting the future efficiency of the system
is needed such as analysis of the interconnections among the
components and modeling of their interactions. The planning of a
IWMS is based fundamentally on technical and economical
opportunities and the legal framework. Modeling the sustainability
and operation effectiveness of a certain IWMS is not in the scope of
the present research. The complexity of the systems and the large
number of the variables require the utilization of a complex approach
to model the outcomes and future risks. This complex method should
be able to evaluate the logical framework of the factors composing
the system and the interconnections between them. The authors of
this paper studied the usability of the Fuzzy Cognitive Map (FCM)
approach modeling the future operation of IWMS’s. The approach
requires two input data set. One is the connection matrix containing
all the factors affecting the system in focus with all the
interconnections. The other input data set is the time series, a
retrospective reconstruction of the weights and roles of the factors.
This paper introduces a novel method to develop time series by
content analysis.
Abstract: Solenoid operated electromagnetic control valve
(ECV) playing an important role for car’s air conditioning control
system. ECV is used in external variable displacement swash plate
type compressor and controls the entire air conditioning system by
means of a pulse width modulation (PWM) input signal supplying
from an external source (controller). Complete form of ECV contains
number of internal features like valve body, core, valve guide,
plunger, guide pin, plunger spring, bellows etc. While designing the
ECV; dimensions of different internal items must meet the standard
requirements as it is quite challenging. In this research paper,
especially the dimensioning of ECV body and its three pressure ports
through which the air/refrigerant passes are considered. Here internal
leakage test analysis of ECV body is being carried out from its
discharge port (Pd) to crankcase port (Pc) when the guide valve is
placed inside it. The experiments have made both in ordinary and
digital system using different assumptions and thereafter compare the
results.
Abstract: In this paper, model order reduction method is used
for approximation in linear and nonlinearity aspects in some
experimental data. This method can be used for obtaining offline
reduced model for approximation of experimental data and can
produce and follow the data and order of system and also it can
match to experimental data in some frequency ratios. In this study,
the method is compared in different experimental data and influence
of choosing of order of the model reduction for obtaining the best and
sufficient matching condition for following the data is investigated in
format of imaginary and reality part of the frequency response curve
and finally the effect and important parameter of number of order
reduction in nonlinear experimental data is explained further.
Abstract: This paper presents a novel statistical description of
the counterpoise effective length due to lightning surges, where the
(impulse) effective length had been obtained by means of regressive
formulas applied to the transient simulation results. The effective
length is described in terms of a statistical distribution function, from
which median, mean, variance, and other parameters of interest could
be readily obtained. The influence of lightning current amplitude,
lightning front duration, and soil resistivity on the effective length has
been accounted for, assuming statistical nature of these parameters. A
method for determining the optimal counterpoise length, in terms of
the statistical impulse effective length, is also presented. It is based on
estimating the number of dangerous events associated with lightning
strikes. Proposed statistical description and the associated method
provide valuable information which could aid the design engineer in
optimising physical lengths of counterpoises in different grounding
arrangements and soil resistivity situations.
Abstract: In Brazil, neonatal mortality rate is considered
incompatible with the country development conditions, and has been
a Public Health concern. Reduction in infant mortality rates has also
been part of the Millennium Development Goals, a commitment
made by countries, members of the Organization of United Nations
(OUN), including Brazil. Fetal mortality rate is considered a highly
sensitive indicator of health care quality. Suitable actions, such as
good quality and access to health services may contribute positively
towards reduction in these fetal and neonatal rates. With appropriate
antenatal follow-up and health care during gestation and delivery,
some death causes could be reduced or even prevented by means of
early diagnosis and intervention, as well as changes in risk factors
and interventions. Objectives: To study the quality of maternal and
infant health care based on fetal and neonatal mortality, as well as the
possible actions to prevent those deaths in Botucatu (Brazil).
Methods: Classification of prevention according to the International
Classification of Diseases and the modified Wigglesworth´s
classification. In order to evaluate adequacy, indicators of quality of
antenatal and delivery care were established by the authors. Results:
Considering fetal deaths, 56.7% of them occurred before delivery,
which reveals possible shortcomings in antenatal care, and 38.2% of
them were a result of intra- labor changes, which could be prevented
or reduced by adequate obstetric management. These findings were
different from those in the group of early neonatal deaths which were
also studied. Adequacy of health services showed that antenatal and
childbirth care was appropriate for 24% and 33.3% of pregnant
women, respectively, which corroborates the results of prevention.
These results revealed that shortcomings in obstetric and antenatal
care could be the causes of deaths in the study. Early and late
neonatal deaths have similar characteristics: 76% could be prevented
or reduced mainly by adequate newborn care (52.9%) and adequate
health care for gestational women (11.7%). When adequacy of care
was evaluated, childbirth and newborn care was adequate in 25.8%
and antenatal care was adequate in 16.1%. In conclusion, direct
relationship was found between adequacy and quality of care
rendered to pregnant women and newborns, and fetal and infant
mortality. Moreover, our findings highlight that deaths could be
prevented by an adequate obstetric and neonatal management.
Abstract: Chemotherapy and radiotherapy are one of the major
treatment modalities that play important role in the management of a
number of different cancers. This study for the first time evaluates the
toxicity of these treatment modalities and its impact on quality of life
of cancer patients in Pakistan. The study also for the first time
determines what cancer patients of different ages and cancer stages
believe would be an effective intervention to manage their
psychosocial needs and treatment induced toxicity. The article also
provides evidence based approach for the use of variety of
interventions to mange cancer treatment induced morbidity and
toxicity. In light of the present study and reviewed research data,
evidence based recommendations are also made for selection of
appropriate interventions to manage Pain, Nausea and Vomiting,
Anxiety and Depression, Fatigue and Overall QOL of cancer
survivors.
Abstract: Text mining techniques are generally applied for
classifying the text, finding fuzzy relations and structures in data
sets. This research provides plenty text mining capabilities. One
common application is text classification and event extraction,
which encompass deducing specific knowledge concerning incidents
referred to in texts. The main contribution of this paper is the
clarification of a concept graph generation mechanism, which is based
on a text classification and optimal fuzzy relationship extraction.
Furthermore, the work presented in this paper explains the application
of fuzzy relationship extraction and branch and bound (BB) method
to simplify the texts.
Abstract: The aim of this study was to design and simulate a
particular type of Asynchronous State Machine (ASM), namely a
‘traffic light controller’ (TLC), operated at a frequency of 0.5 Hz.
The design task involved two main stages: firstly, designing a 4-bit
binary counter using J-K flip flops as the timing signal and,
subsequently, attaining the digital logic by deploying ASM design
process. The TLC was designed such that it showed a sequence of
three different colours, i.e. red, yellow and green, corresponding to
set thresholds by deploying the least number of AND, OR and NOT
gates possible. The software Multisim was deployed to design such
circuit and simulate it for circuit troubleshooting in order for it to
display the output sequence of the three different colours on the
traffic light in the correct order. A clock signal, an asynchronous 4-
bit binary counter that was designed through the use of J-K flip flops
along with an ASM were used to complete this sequence, which was
programmed to be repeated indefinitely. Eventually, the circuit was
debugged and optimized, thus displaying the correct waveforms of
the three outputs through the logic analyser. However, hazards
occurred when the frequency was increased to 10 MHz. This was
attributed to delays in the feedback being too high.
Abstract: Equal channel angular pressing (ECAP) of
commercial Al-Mg-Si alloy was conducted using two strain rates.
The ECAP processing was conducted at room temperature and at
250°C. Route A was adopted up to a total number of four passes in
the present work. Structural evolution of the aluminum alloy discs
was investigated before and after ECAP processing using optical
microscopy (OM). Following ECAP, simple compression tests and
Vicker’s hardness were performed. OM micrographs showed that, the
average grain size of the as-received Al-Mg-Si disc tends to be larger
than the size of the ECAP processed discs. Moreover, significant
difference in the grain morphologies of the as-received and processed
discs was observed. Intensity of deformation was observed via the
alignment of the Al-Mg-Si consolidated particles (grains) in the
direction of shear, which increased with increasing the number of
passes via ECAP. Increasing the number of passes up to 4 resulted in
increasing the grains aspect ratio up to ~5. It was found that the
pressing temperature has a significant influence on the
microstructure, Hv-values, and compressive strength of the processed
discs. Hardness measurements demonstrated that 1-pass resulted in
increase of Hv-value by 42% compared to that of the as-received
alloy. 4-passes of ECAP processing resulted in additional increase in
the Hv-value. A similar trend was observed for the yield and
compressive strength. Experimental data of the Hv-values
demonstrated that there is a lack of any significant dependence on the
processing strain rate.
Abstract: Shortfall of electrical energy in Pakistan is a challenge
adversely affecting its industrial output and social growth. As
elsewhere, Pakistan derives its electrical energy from a number of
conventional sources. The exhaustion of petroleum and conventional
resources, the rising costs coupled with extremely adverse climatic
effects are taking its toll especially on the under-developed countries
like Pakistan. As alternate, renewable energy sources like hydropower,
solar, wind, even bio-energy and a mix of some or all of them
could provide a credible alternative to the conventional energy
resources that would not only be cleaner but sustainable as well. As a
model, solar energy-based power grid for the near future has been
attempted to offset the energy shortfalls as a mix with our existing
sustainable natural energy resources. An assessment of solar energy
potential for electricity generation is being presented for fulfilling the
energy demands with higher level of reliability and sustainability.
This model is based on the premise that solar energy potential of
Pakistan is not only reliable but also sustainable. This research
estimates the present & future approaching renewable energy
resource specially the impact of solar energy based power grid for
mitigating energy shortage in Pakistan.
Abstract: Pipe failure and leakage is a problematic issue and the
traditional solution of replacing the pipes is costly and time
consuming. Rehabilitation by relining materials based on polymer
composites is an alternative solution towards the degradation problem
of the old piping. This paper provides a brief summary of advances in
technology, methods and materials for relining as well as a summary
of the degradation analyses of the two main composite materials used
for relining, rubber filled epoxy and reinforced polyester baltoflake
when they are exposed in deionized water and elevated temperature
up to 80°C for a duration of 2-14 months in the laboratory.
Abstract: Complexation of anthocyanins to mimic natural
copigmentation process was investigated. Cyanidin-rich extracts from
Zea mays L. ceritina Kulesh. and delphinidin-rich extracts from
Clitoria ternatea L. were used to form 4 anthocyanin complexes,
AC1, AC2, AC3 and AC4, in the presence of several polyphenols and
a trace metal. Characterizations of the ACs were conducted by UV,
FTIR, DSC/TGA and morphological observations. Bathochromic
shifts of the UV spectra of 4 formulas of ACs were observed at peak
wavelengths of about 510-620 nm by 10 nm suggesting complex
formation. FTIR spectra of the ACs indicate shifts of peaks from
1,733 cm-1 to 1,696 cm-1 indicating interactions and a decrease in the
peak areas within the wavenumber of 3,400-3,500 cm-1 indicating
changes in hydrogen bonding. Thermal analysis of all of the ACs
suggests increases in melting temperature after complexation. AC
with the highest melting temperature was morphologically observed
by SEM and TEM to be crystal-like particles within a range of 50 to
200 nm. Particle size analysis of the AC by laser diffraction gave a
range of 50-600 nm, indicating aggregation. This AC was shown to
have no cytotoxic effect on cultured HGEPp0.5 and HGF (all p>
0.05) by MTT. Therefore, complexation of anthocyanins was simple
and self-assembly process, potentially resulting in nanosized particles
of anthocyanin complex.
Abstract: A mixed method by combining modified pole
clustering technique and modified cauer continued fraction is
proposed for reducing the order of the large-scale dynamic systems.
The denominator polynomial of the reduced order model is obtained
by using modified pole clustering technique while the coefficients of
the numerator are obtained by modified cauer continued fraction.
This method generated 'k' number of reduced order models for kth
order reduction. The superiority of the proposed method has been
elaborated through numerical example taken from the literature and
compared with few existing order reduction methods.
Abstract: The article deals with one of the most significant
issues concerning the functioning of the public sector in the European
Union. The objectives of good governance were formulated by the
EU itself and also the Scholars in reaction to the discussion that
started a decade ago and concerned the role of the government in 21st
century, the future of integration processes and globalization
challenges in Europe. Currently, the concept of good governance is
mainly associated with the improvement of management of public
policies in the European Union, concerning both domestic and EU
policies. However, it goes beyond the issues of state capacity and
effectiveness of management. Good governance relates also to
societal participation in the public administration and verification of
decisions made in public authorities’ (including public
administration). Indirectly, the concept and practice of good
governance are connected to societal legitimisation of public bodies
in the European Union.
Abstract: The design, manufacture, and operation of thin-walled
pressure vessels must be based on maximum safe operating pressure
and an adequate factor of safety (FoS). This research paper first
reports experimental evaluation of longitudinal and hoops stresses
based on working pressure as well as maximum pressure; and then
includes a critical study of factor of safety (FoS) in the design of a
glass fiber pressure vessel. Experimental work involved the use of
measuring instruments and the readings from pressure gauges.
Design calculations involved the computations of design stress and
FoS; the latter was based on breaking strength of 55 MPa for the
glass fiber (pressure-vessel material). The experimentally determined
FoS value has been critically compared with the general FoS allowed
in the design of glass fiber pressure vessels.
Abstract: The present study was carried out to evaluate the
effect of different levels of dietary seed and extract of Harmal
(Peganum harmala L.) on immunity of broiler chicks. A total of 350
one-day old broiler chicks (Ross 308) were randomly allocated to
five dietary treatments with four replicates pen of 14 birds each.
Dietary treatments consisted of control, 1 and 2 g/kg Harmal seed in
diet, 100 and 200 mg/L Harmal seed extract in water. Broilers
received dietary treatments from 1 to 42 d. Two birds from each pen
were randomly weighed and sacrificed at 42 d of age, the relative
weight of lymphoid organs (bursa of Fabercius and spleen) to live
weight were calculated. Antibody titers against Newcastle and
influenza viruses and sheep red blood cell were measured at 30 d of
age. Results showed that the relative weights of lymphoid organs
were not affected by dietary treatments. Furthermore, antibody titer
against Newcastle and influenza viruses as well as sheep red blood
cell antigen were significantly (P
Abstract: Lightweight design represents an important key to
successful implementation of energy-saving, fuel-efficient and
environmentally friendly means of transport in the aerospace and
automotive industry. In this context the use of carbon fibre reinforced
plastics (CFRP) which are distinguished by their outstanding
mechanical properties at relatively low weight, promise significant
improvements. Due to the reduction of the total mass, with the
resulting lowered fuel or energy consumption and CO2 emissions
during the operational phase, commercial aircraft will increasingly be
made of CFRP. An auspicious technology for the efficient and
economic production of high performance thermoset composites and
hybrid structures for future lightweight applications is the
combination of carbon fibre sheet moulding compound, tailored
continuous carbon fibre reinforcements and metallic components in a
one-shot pressing and curing process. This paper deals with a hybrid
composite technology for aerospace industries, which was developed
with the help of a special innovation and development system.
Abstract: A Distributed Denial of Service (DDoS) attack is a
major threat to cyber security. It originates from the network layer or
the application layer of compromised/attacker systems which are
connected to the network. The impact of this attack ranges from the
simple inconvenience to use a particular service to causing major
failures at the targeted server. When there is heavy traffic flow to a
target server, it is necessary to classify the legitimate access and
attacks. In this paper, a novel method is proposed to detect DDoS
attacks from the traces of traffic flow. An access matrix is created
from the traces. As the access matrix is multi dimensional, Principle
Component Analysis (PCA) is used to reduce the attributes used for
detection. Two classifiers Naive Bayes and K-Nearest neighborhood
are used to classify the traffic as normal or abnormal. The
performance of the classifier with PCA selected attributes and actual
attributes of access matrix is compared by the detection rate and
False Positive Rate (FPR).