Abstract: Repairing of the cracks by fiber metal laminates
(FMLs) was first done by some aeronautical laboratories in early
1970s. In this study, experimental investigations were done on the
effect of repairing the center-cracked aluminum plates using the FML
patches. The repairing processes were conducted to characterize the
response of the repaired structures to tensile tests. The composite
patches were made of one aluminum layer and two woven glassepoxy
composite layers. Three different crack lengths in three crack
angles and different patch lay-ups were examined. It was observed
for the lengthen cracks, the effect of increasing the crack angle on
ultimate tensile load in the structure was increase. It was indicated
that the situation of metal layer in the FML patches had an important
effect on the tensile response of the tested specimens. It was found
when the aluminum layer is farther, the ultimate tensile load has the
highest amount.
Abstract: This paper present some preliminary work on the
preparation and physicochemical caracterization of nanocomposite
MFI-alumina structures based on alumina hollow fibres. The fibers
are manufactured by a wet spinning process. α-alumina particles were
dispersed in a solution of polysulfone in NMP. The resulting slurry is
pressed through the annular gap of a spinneret into a precipitation
bath. The resulting green fibres are sintered. The mechanical strength
of the alumina hollow fibres is determined by a three-point-bending
test while the pore size is characterized by bubble-point testing. The
bending strength is in the range of 110 MPa while the average pore
size is 450 nm for an internal diameter of 1 mm and external diameter
of 1.7 mm. To characterize the MFI membranes various techniques
were used for physicochemical characterization of MFI–ceramic
hollow fibres membranes: The nitrogen adsorption, X-ray
diffractometry, scanning electron microscopy combined with X
emission microanalysis. Scanning Electron Microscopy (SEM) and
Energy Dispersive Microanalysis by the X-ray were used to observe
the morphology of the hollow fibre membranes (thickness,
infiltration into the carrier, defects, homogeneity). No surface film,
has been obtained, as observed by SEM and EDX analysis and
confirmed by high temperature variation of N2 and CO2 gas
permeances before cation exchange. Local analysis and characterise
(SEM and EDX) and overall (by ICP elemental analysis) were
conducted on two samples exchanged to determine the quantity and
distribution of the cation of cesium on the cross section fibre of the
zeolite between the cavities.
Abstract: The growing problem of youth unemployment in
Egypt after the 25th January Revolution has directed the attention of
some human resource experts towards considering remote
employment as a partial remedy for the unemployed youth instead of
the unavailable traditional jobs, a trend which will also help with the
congested offices and unsolved traffic problem in Cairo and spread
a flexible work culture, but despite of that, the main issue remains
unresolved for these organizations to deal with the system challenges.
In the past few years, in developed countries, there has been a
growing trend for many companies to shift to remote employment
instead of the traditional office employment for many reasons: due to
the growing technological advances that helped some employees do
their work from home on a part time basis, the need for achieving an
employee-s work balance in the middle of unbalanced complicated
life, top management focus on employee-s productivity rather their
time spent at work. The objective of this paper is to study and analyze
the advantages and challenges that Egypt-s labor force will be facing
in their implementation of remote or virtual employment in both
government and private organizations after the 25th January
revolution. Therefore, the research question will be: What are the
advantages and different challenges that Egyptian organizations
might face in their implementation for remote employment system
and how can they manage these challenges for the system to work
effectively? The study is divided into six main parts: the introduction,
objective and importance of the study, research problem,
methodology, experience of some countries that implemented remote
employment, advantages and challenges of implementing remote
employment in Egypt and then the conclusion which discuses the
results and recommendations of the study.
Abstract: Flow-shop scheduling problem (FSP) deals with the
scheduling of a set of jobs that visit a set of machines in the same
order. The FSP is NP-hard, which means that an efficient algorithm
for solving the problem to optimality is unavailable. To meet the
requirements on time and to minimize the make-span performance of
large permutation flow-shop scheduling problems in which there are
sequence dependent setup times on each machine, this paper
develops one hybrid genetic algorithms (HGA). Proposed HGA
apply a modified approach to generate population of initial
chromosomes and also use an improved heuristic called the iterated
swap procedure to improve initial solutions. Also the author uses
three genetic operators to make good new offspring. The results are
compared to some recently developed heuristics and computational
experimental results show that the proposed HGA performs very
competitively with respect to accuracy and efficiency of solution.
Abstract: Dengue fever has become a major concern for health
authorities all over the world particularly in the tropical countries.
These countries, in particular are experiencing the most worrying
outbreak of dengue fever (DF) and dengue haemorrhagic fever
(DHF). The DF and DHF epidemics, thus, have become the main
causes of hospital admissions and deaths in Malaysia. This paper,
therefore, attempts to examine the environmental factors that may
influence the recent dengue outbreak. The aim of this study is twofold,
firstly is to establish a statistical model to describe the
relationship between the number of dengue cases and a range of
explanatory variables and secondly, to identify the lag operator for
explanatory variables which affect the dengue incidence the most.
The explanatory variables involved include the level of cloud cover,
percentage of relative humidity, amount of rainfall, maximum
temperature, minimum temperature and wind speed. The Poisson and
Negative Binomial regression analyses were used in this study. The
results of the analyses on the 915 observations (daily data taken from
July 2006 to Dec 2008), reveal that the climatic factors comprising of
daily temperature and wind speed were found to significantly
influence the incidence of dengue fever after 2 and 3 weeks of their
occurrences. The effect of humidity, on the other hand, appears to be
significant only after 2 weeks.
Abstract: In this paper, many techniques for blind identification of moving average (MA) process are presented. These methods utilize third- and fourth-order cumulants of the noisy observations of the system output. The system is driven by an independent and identically distributed (i.i.d) non-Gaussian sequence that is not observed. Two nonlinear optimization algorithms, namely the Gradient Descent and the Gauss-Newton algorithms are exposed. An algorithm based on the joint-diagonalization of the fourth-order cumulant matrices (FOSI) is also considered, as well as an improved version of the classical C(q, 0, k) algorithm based on the choice of the Best 1-D Slice of fourth-order cumulants. To illustrate the effectiveness of our methods, various simulation examples are presented.
Abstract: Monoculture and mixed cultures of microalgae and
the oleaginous yeast for microbial oil productions were investigated
using sugarcane juice as carbon substrate. The monoculture of yeast
Torulaspora maleeae Y30, Torulaspora globosa YU5/2 grew faster
than that of microalgae Chlorella sp. KKU-S2. In monoculture of T.
maleeae Y30, a biomass of 8.267g/L with lipid yield of 0.920g/L
were obtained, while 8.333g/L of biomass with lipid yield of
1.141g/L were obtained for monoculture of T. globosa YU5/2. A
biomass of 1.933g/L with lipid yield of 0.052g/L was found for
monoculture of Chlorella sp. KKU-S2. The biomass concentration in
the mixed culture of the oleaginous yeast with microalgae increased
faster and was higher compared with that in the monocultures. A
biomass of 8.733g/L with lipid yield of 1.564g/L was obtained for a
mixed culture of T. maleeae Y30 with Chlorella sp. KKU-S2, while
8.010g/L of biomass with lipid yield of 2.424g/L was found for
mixed culture of T. globosa YU5/2 with Chlorella sp. KKU-S2.
Maximum cell yield coefficient (YX/S, g/L) was found of 0.323 in
monoculture of Chlorella sp. KKU-S2 but low level of both specific
yield of lipid (YP/X, g lipid/g cells) of 0.027 and volumetric lipid
production rate (QP, g/L/d) of 0.003 were observed. While, maximum
YP/X (0.303), QP (0.105) and maximum process product yield (YP/S,
0.061) were obtained in mixed culture of T. globosa YU5/2 with
Chlorella sp. KKU-S2. The results obtained from the study shows
that mixed culture of yeast with microalgae is a desirable cultivation
process for microbial oil production.
Abstract: This paper presents the experimental results of silicone rubber housing material for 24kV lightning arrester under artificial accelerated ageing test based on IEC 61109 specifications. Specimens having inclined and alternated shed made of HTV silicone rubber with ATH content and having leakage distance 625 mm were tested continuously 1000 hrs in artificial salt fog chamber. After 1000 hrs of salt fog ageing test, obviously surface erosion was observed on trunk between the upper large shed and the lower small shed near the energized end. Decreasing in hydrophobicity and increasing in hardness were measured on tested specimen comparing with new specimen. Chemical analysis by ATR-FTIR confirmed the observation results.
Abstract: The research investigates the “impact of VLE on mathematical concepts acquisition of the special education needs (SENs) students at KS4 secondary education sector" in England. The overall aim of the study is to establish possible areas of difficulties to approach for above or below knowledge standard requirements for KS4 students in the acquisition and validation of basic mathematical concepts. A teaching period, in which virtual learning environment (Fronter) was used to emphasise different mathematical perception and symbolic representation was carried out and task based survey conducted to 20 special education needs students [14 actually took part]. The result shows that students were able to process information and consider images, objects and numbers within the VLE at early stages of acquisition process. They were also able to carry out perceptual tasks but with limiting process of different quotient, thus they need teacher-s guidance to connect them to symbolic representations and sometimes coach them through. The pilot study further indicates that VLE curriculum approaches for students were minutely aligned with mathematics teaching which does not emphasise the integration of VLE into the existing curriculum and current teaching practice. There was also poor alignment of vision regarding the use of VLE in realisation of the objectives of teaching mathematics by the management. On the part of teacher training, not much was done to develop teacher-s skills in the technical and pedagogical aspects of VLE that is in-use at the school. The classroom observation confirmed teaching practice will find a reliance on VLE as an enhancer of mathematical skills, providing interaction and personalisation of learning to SEN students.
Abstract: ZnO-SnO2 i.e. Zinc-Tin-Oxide (ZTO) thin films were
deposited on glass substrate with varying concentrations (ZnO:SnO2
- 100:0, 90:10, 70:30 and 50:50 wt.%) at room temperature by flash
evaporation technique. These deposited ZTO film were annealed at
450 0C in vacuum. These films were characterized to study the effect
of annealing on the structural, electrical, and optical properties.
Atomic force microscopy (AFM) and Scanning electron microscopy
(SEM) images manifest the surface morphology of these ZTO thin
films. The apparent growth of surface features revealed the formation
of nanostructure ZTO thin films. The small value of surface
roughness (root mean square RRMS) ensures the usefulness in
optical coatings. The sheet resistance was also found to be decreased
for both types of films with increasing concentration of SnO2. The
optical transmittance found to be decreased however blue shift has
been observed after annealing.
Abstract: Some of the students' problems in writing skill stem
from inadequate preparation for the writing assignment. Students
should be taught how to write well when they arrive in language
classes. Having selected a topic, the students examine and explore the
theme from as large a variety of viewpoints as their background and
imagination make possible. Another strategy is that the students
prepare an Outline before writing the paper. The comparison between
the two mentioned thought provoking techniques was carried out
between the two class groups –students of Islamic Azad University of
Dezful who were studying “Writing 2" as their main course. Each
class group was assigned to write five compositions separately in
different periods of time. Then a t-test for each pair of exams between
the two class groups showed that the t-observed in each pair was
more than the t-critical. Consequently, the first hypothesis which
states those who utilize Brainstorming as a thought provoking
technique in prewriting phase are more successful than those who
outline the papers before writing was verified.
Abstract: Using activity theory, organisational theory and
didactics as theoretical foundations, a comprehensive model of the
organisational dimensions relevant for learning and knowledge
transfer will be developed. In a second step, a Learning Assessment
Guideline will be elaborated. This guideline will be designed to
permit a targeted analysis of organisations to identify the status quo
in those areas crucial to the implementation of learning and
knowledge transfer. In addition, this self-analysis tool will enable
learning managers to select adequate didactic models for e- and
blended learning. As part of the European Integrated Project
"Process-oriented Learning and Information Exchange" (PROLIX),
this model of organisational prerequisites for learning and knowledge
transfer will be empirically tested in four profit and non-profit
organisations in Great Britain, Germany and France (to be finalized
in autumn 2006). The findings concern not only the capability of the
model of organisational dimensions, but also the predominant
perceptions of and obstacles to learning in organisations.
Abstract: Total liquid ventilation can support gas exchange in animal models of lung injury. Clinical application awaits further technical improvements and performance verification. Our aim was to develop a liquid ventilator, able to deliver accurate tidal volumes, and a computerized system for measuring lung mechanics. The computer-assisted, piston-driven respirator controlled ventilatory parameters that were displayed and modified on a real-time basis. Pressure and temperature transducers along with a lineal displacement controller provided the necessary signals to calculate lung mechanics. Ten newborn lambs (
Abstract: Water, soil and sediment contaminated with
metolachlor poses a threat to the environment and human health.
We determined the effectiveness of nano-zerovalent iron (NZVI) to
dechlorinate metolachlor [2-chloro-n-(2-ethyl-6-methyl-phenyl)-n-
(1-methoxypropan-2-yl)acetamide] in pH solution and the presence
of aluminium salt. The optimum dosage of degradation of 100 mlL-1
metolachlor was 1% (w/v) NZVI. The degradation kinetic rate (kobs)
was 0.218×10-3 min-1 and specific first-order rates (kSA) was
8.72×10-7 L m-2min-1. By treating aqueous solutions of metolachlor
with NZVI, metolachlor destruction rate were increased as the pH
decrease from 10 to 4. Lowering solution pH removes Fe (III)
passivating layers from the NZVI and makes it free for reductive
transformations. Destruction kinetic rates were 20.8×10-3 min-1 for
pH4, 18.9×10-3 min-1 for pH7, 13.8×10-3 min-1 for pH10. In addition,
destruction kinetic of metolachlor by NZVI was enhanced when
aluminium sulfate was added. The destruction kinetic rate were
20.4×10-3 min-1 for 0.05% Al(SO4)3 and 60×10-3 min-1 for 0.1%
Al(SO4)3.
Abstract: This paper addresses the problem of blind source separation
(BSS). To recover original signals, from linear instantaneous
mixtures, we propose a new contrast function based on the use of a
double referenced system. Our approach assumes statistical independence
sources. The reference vectors will be incrusted in the cumulant
to evaluate the independence. The estimation of the separating matrix
will be performed in two steps: whitening observations and joint
diagonalization of a set of referenced cumulant matrices. Computer
simulations are presented to demonstrate the effectiveness of the
suggested approach.
Abstract: This paper presents a web based remote access
microcontroller laboratory. Because of accelerated development in
electronics and computer technologies, microcontroller-based devices
and appliances are found in all aspects of our daily life. Before the
implementation of remote access microcontroller laboratory an
experiment set is developed by teaching staff for training
microcontrollers. Requirement of technical teaching and industrial
applications are considered when experiment set is designed.
Students can make the experiments by connecting to the experiment
set which is connected to the computer that set as the web server. The
students can program the microcontroller, can control digital and
analog inputs and can observe experiment. Laboratory experiment
web page can be accessed via www.elab.aku.edu.tr address.
Abstract: This study investigates the relationships between
Work Motivation, Work Stress, and Job Satisfaction toward
cross-strait employees. The target subjects are three
manufacturing firms in Mainland China and Taiwan. Out of 450
distributed surveys, 352 valid surveys were obtained with the
response rate of 78.22%.The findings have addressed three main
pull factors toward cross-strait employees in choosing jobs, which
are (1) high level of firm stability, (2) good firm image, and (3)
good employee benefits. In addition, various employee attributes
exert different impacts on Work Motivation, Work Stress, and
Job Satisfaction. The comparison between expected and actual
perceived Job Satisfaction toward cross-strait employees shows
that “salary" ranks highest regarding expected Job Satisfaction
whereas “co-worker relationship" ranks highest regarding actual
perceived Job Satisfaction, which implies actual perceived Job
Satisfaction do not match employee expectations. Therefore, this
research further concludes that there exists differences between
employees- expected and actual perceived Job Satisfaction.
Abstract: This study examined the role of driving experience in hazard perception and categorization using traffic scene pictures. Specifically, young-inexperienced, moderately experienced and very experienced (taxi) drivers observed traffic scene pictures while connected to an eye tracking system and were asked to rate the level of hazardousness of each picture and to mention the three most prominent hazards in it. Target pictures included nine, nearly identical, pairs of pictures where one picture in each pair included an actual hazard as an additional element. Altogether, 22 areas of interest (AOIs) were predefined and included 13 potential hazards and 9 actual hazards. Data analysis included both verbal reports and eye scanning patterns of these AOIs. Generally, both experienced and taxi drivers noted a relatively larger number of potential hazards than young inexperienced drivers Thus, by relating to less salient potential hazards, experienced drivers have demonstrated a better situation model of the traffic environment.
Abstract: Observations show that power plant efficiency
decreases in hot summer days. Water droplet injection in air
condensers is suggested in order to decrease the inlet air temperature.
Nozzle arrangement, injected water flow rate and droplets diameter
effects on evaporation rate and the resulting air temperature are
investigated using numerical simulation. Decreasing the diameter of
injected droplets and increasing the number of injecting nozzles,
decreases the outlet air temperature. Also a more uniform air
temperature can be obtained using more injecting nozzles. Numerical
results are in good agreement with analytical results.