Abstract: In this paper 3D FEM analysis was carried out on
double lap bonded joint with composite adherents subjected to
dynamic shear. The adherents are made of Carbon/Epoxy while the
adhesive is epoxy Araldite 2031. The maximum average shear stress
and the stress homogeneity in the adhesive layer were examined.
Three fibers textures were considered: UD; 2.5D and 3D with same
volume fiber then a parametric study based on changing the thickness
and the type of fibers texture in 2.5D was accomplished. Moreover,
adherents’ dissimilarity was also investigated. It was found that the
main parameter influencing the behavior is the longitudinal stiffness
of the adherents. An increase in the adherents’ longitudinal stiffness
induces an increase in the maximum average shear stress in the
adhesive layer and an improvement in the shear stress homogeneity
within the joint. No remarkable improvement was observed for
dissimilar adherents.
Abstract: Polycyclic aromatic hydrocarbons (PAHs) are formed
during the pyrolysis of scrap tyres to produce tyre pyrolytic oil
(TPO). Due to carcinogenic, mutagenic, and toxic properties PAHs
are priority pollutants. Hence it is essential to remove PAHs from
TPO before utilising TPO as a petroleum fuel alternative (to run the
engine). Agricultural wastes have promising future to be utilized as
biosorbent due to their cost effectiveness, abundant availability, high
biosorption capacity and renewability. Various low cost adsorbents
were prepared from natural sources. Uptake of PAHs present in tyre
pyrolytic oil was investigated using various low-cost adsorbents of
natural origin including sawdust (shisham), coconut fiber, neem bark,
chitin, activated charcoal. Adsorption experiments of different PAHs
viz. naphthalene, acenaphthalene, biphenyl and anthracene have been
carried out at ambient temperature (25°C) and at pH 7. It was
observed that for any given PAH, the adsorption capacity increases
with the lignin content. Freundlich constant Kf and 1/n have been
evaluated and it was found that the adsorption isotherms of PAHs
were in agreement with a Freundlich model, while the uptake
capacity of PAHs followed the order: activated charcoal> saw dust
(shisham) > coconut fiber > chitin. The partition coefficients in
acetone-water, and the adsorption constants at equilibrium, could be
linearly correlated with octanol–water partition coefficients. It is
observed that natural adsorbents are good alternative for PAHs
removal. Sawdust of Dalbergia sissoo, a by-product of sawmills was
found to be a promising adsorbent for the removal of PAHs present in
TPO. It is observed that adsorbents studied were comparable to those
of some conventional adsorbents.
Abstract: Blueberries are widely valued for their high content in
phenolic compounds with antioxidant activity, and hence beneficial
for the human health. In this way, a study was done to determine the
phenolic composition (total phenols, anthocyanins and tannins) and
antioxidant activity of blueberries from three cultivars (Duke,
Bluecrop, and Ozarkblue) grown in two different Portuguese farms.
Initially two successive extractions were done with methanol
followed by two extractions with aqueous acetone solutions. These
extracts obtained were then used to evaluate the amount of phenolic
compounds and the antioxidant activity. The total phenols were
observed to vary from 4.9 to 8.2 mg GAE/g fresh weight, with
anthocyanin’s contents in the range 1.5-2.8 mg EMv3G/g and tannins
contents in the range 1.5- 3.8 mg/g. The results for antioxidant
activity ranged from 9.3 to 23.2 molTE/g and from 24.7 to 53.4molTE/g, when measured, respectively, by DPPH and ABTS
methods. In conclusion it was observed that, in general, the cultivar
had a visible effect on the phenols present, and furthermore, the
geographical origin showed relevance either in the phenols contents
or the antioxidant activity.
Abstract: This experimental study evaluates the effect of using
Cognitive-Behavioral Therapy (CBT) and Multidimensional Self-
Concept Model (MSCM) in a drug prevention programme to increase
resiliency and reduce aggression among at-risk youth in Malaysia. A
number of 60 (N=60) university students who were at-risk of taking
drugs were involved in this study. Participants were identified with
self-rating scales, Adolescent Resilience Attitude Scale (ARAS) and
Aggression Questionnaire. Based on the mean score of these
instruments, the participants were divided into the treatment group,
and the control group. Data were analyzed using t-test. The finding
showed that the mean score of resiliency was increased in the
treatment group compared to the control group. It also shows that the
mean score of aggression was reduced in the treatment group
compared to the control group. Drug Prevention Programme was
found to help in enhancing resiliency and reducing aggression among
participants in the treatment group compared to the controlled group.
Implications were given regarding the preventive actions on drug
abuse among youth in Malaysia.
Abstract: China is currently the world's largest producer and distributor of electric bicycle (e-bike). The increasing number of e-bikes on the road is accompanied by rising injuries and even deaths of e-bike drivers. Therefore, there is a growing need to improve the safety structure of e-bikes. This 3D frictionless contact analysis is a preliminary, but necessary work for further structural design improvement of an e-bike. The contact analysis between e-bike and the ground was carried out as follows: firstly, the Penalty method was illustrated and derived from the simplest spring-mass system. This is one of the most common methods to satisfy the frictionless contact case; secondly, ANSYS static analysis was carried out to verify finite element (FE) models with contact pair (without friction) between e-bike and the ground; finally, ANSYS transient analysis was used to obtain the data of the penetration p(u) of e-bike with respect to the ground. Results obtained from the simulation are as estimated by comparing with that from theoretical method. In the future, protective shell will be designed following the stability criteria and added to the frame of e-bike. Simulation of side falling of the improvedsafety structure of e-bike will be confirmed with experimental data.
Abstract: Employers occupational safety and health training
obligations are regulated in 89/391/EEC Framework Directive and
also in 6331 numbered Occupational Health and Safety Law in
Turkey.
The main objective of this research is to determine and evaluate
the employers’ occupational health and safety training obligations in
Framework Directive in comparison with the 6331 numbered
Occupational Health and Safety Law and to examine training
principles in Turkey. For this purpose, employers’ occupational
health and safety training obligations examined in Framework
Directive and Occupational Health and Safety Law. This study
carried out through comparative scanning model and literature model.
The research data were collected through European Agency and
ministry legislations.
As a result, employers’ occupational health and safety training
obligations in the 6331 numbered Occupational Health and Safety
Law are compatible with the 89/391/EEC numbered Framework
Directive and training principles are determined by in different ways
like the trained workers, training issues, training period, training time
and trainers. In this study, employers’ training obligations are
evaluated in detail.
Abstract: The aim of this work is to build a model based on
tissue characterization that is able to discriminate pathological and
non-pathological regions from three-phasic CT images. With our
research and based on a feature selection in different phases, we are
trying to design a neural network system with an optimal neuron
number in a hidden layer. Our approach consists of three steps:
feature selection, feature reduction, and classification. For each
region of interest (ROI), 6 distinct sets of texture features are
extracted such as: first order histogram parameters, absolute gradient,
run-length matrix, co-occurrence matrix, autoregressive model, and
wavelet, for a total of 270 texture features. When analyzing more
phases, we show that the injection of liquid cause changes to the high
relevant features in each region. Our results demonstrate that for
detecting HCC tumor phase 3 is the best one in most of the features
that we apply to the classification algorithm. The percentage of
detection between pathology and healthy classes, according to our
method, relates to first order histogram parameters with accuracy of
85% in phase 1, 95% in phase 2, and 95% in phase 3.
Abstract: Micro-alloyed steel components are used in
automotive industry for the necessity to make the manufacturing
process cycles shorter when compared to conventional steel by
eliminating heat treatment cycles, so an important saving of costs and
energy can be reached by reducing the number of operations. Microalloying
elements like vanadium, niobium or titanium have been
added to medium carbon steels to achieve grain refinement with or
without precipitation strengthening along with uniform
microstructure throughout the matrix. Present study reports the
applicability of medium carbon vanadium micro-alloyed steel in hot
forging. Forgeability has been determined with respect to different
cooling rates, after forging in a hydraulic press at 50% diameter
reduction in temperature range of 900-11000C. Final microstructures,
hardness, tensile strength, and impact strength have been evaluated.
The friction coefficients of different lubricating conditions, viz.,
graphite in hydraulic oil, graphite in furnace oil, DF 150 (Graphite,
Water-Based) die lubricant and dry or without any lubrication were
obtained from the ring compression test for the above micro-alloyed
steel. Results of ring compression tests indicate that graphite in
hydraulic oil lubricant is preferred for free forging and dry lubricant
is preferred for die forging operation. Exceptionally good forgeability
and high resistance to fracture, especially for faster cooling rate has
been observed for fine equiaxed ferrite-pearlite grains, some amount
of bainite and fine precipitates of vanadium carbides and
carbonitrides. The results indicated that the cooling rate has a
remarkable effect on the microstructure and mechanical properties at
room temperature.
Abstract: The ultrasound imaging is very popular to diagnosis
the disease because of its non-invasive nature. The ultrasound
imaging slowly produces low quality images due to the presence of
spackle noise and wave interferences. There are several algorithms to
be proposed for the segmentation of ultrasound carotid artery images
but it requires a certain limit of user interaction. The pixel in an
image is highly correlated so the spatial information of surrounding
pixels may be considered in the process of image segmentation which
improves the results further. When data is highly correlated, one pixel
may belong to more than one cluster with different degree of
membership. There is an important step to computerize the evaluation
of arterial disease severity using segmentation of carotid artery lumen
in 2D and 3D ultrasonography and in finding vulnerable
atherosclerotic plaques susceptible to rupture which can cause stroke.
Abstract: In this paper, we regard as a coded transmission over a
frequency-selective channel. We plan to study analytically the
convergence of the turbo-detector using a maximum a posteriori
(MAP) equalizer and a MAP decoder. We demonstrate that the
densities of the maximum likelihood (ML) exchanged during the
iterations are e-symmetric and output-symmetric. Under the Gaussian
approximation, this property allows to execute a one-dimensional
scrutiny of the turbo-detector. By deriving the analytical terminology
of the ML distributions under the Gaussian approximation, we confirm
that the bit error rate (BER) performance of the turbo-detector
converges to the BER performance of the coded additive white
Gaussian noise (AWGN) channel at high signal to noise ratio (SNR),
for any frequency selective channel.
Abstract: The decision-making process is theoretically clearly
defined. Generally, it includes the problem identification and
analysis, data gathering, goals and criteria setting, alternatives
development and optimal alternative choice and its implementation.
In practice however, various modifications of the theoretical
decision-making process can occur. The managers can consider some
of the phases to be too complicated or unfeasible and thus they do not
carry them out and conversely some of the steps can be
overestimated.
The aim of the paper is to reveal and characterize the perception of
the individual phases of decision-making process by the managers.
The research is concerned with managers in the military environment
– commanders. Quantitative survey is focused cross-sectionally in the
individual levels of management of the Ministry of Defence of the
Czech Republic. On the total number of 135 respondents the analysis
focuses on which of the decision-making process phases are
problematic or not carried out in practice and which are again
perceived to be the easiest. Then it is examined the reasons of the
findings.
Abstract: This paper proposes a mathematical model and
examines the performance of an exact algorithm for a location–
transportation problems in humanitarian relief. The model determines
the number and location of distribution centers in a relief network,
the amount of relief supplies to be stocked at each distribution center
and the vehicles to take the supplies to meet the needs of disaster
victims under capacity restriction, transportation and budgetary
constraints. The computational experiments are conducted on the
various sizes of problems that are generated. Branch and bound
algorithm is applied for these problems. The results show that this
algorithm can solve problem sizes of up to three candidate locations
with five demand points and one candidate location with up to twenty
demand points without premature termination.
Abstract: In this paper, we consider the vehicle routing problem
with mixed fleet of conventional and heterogenous electric vehicles
and time dependent charging costs, denoted VRP-HFCC, in which
a set of geographically scattered customers have to be served by a
mixed fleet of vehicles composed of a heterogenous fleet of Electric
Vehicles (EVs), having different battery capacities and operating
costs, and Conventional Vehicles (CVs). We include the possibility
of charging EVs in the available charging stations during the routes
in order to serve all customers. Each charging station offers charging
service with a known technology of chargers and time dependent
charging costs. Charging stations are also subject to operating time
windows constraints. EVs are not necessarily compatible with all
available charging technologies and a partial charging is allowed.
Intermittent charging at the depot is also allowed provided that
constraints related to the electricity grid are satisfied.
The objective is to minimize the number of employed vehicles and
then minimize the total travel and charging costs.
In this study, we present a Mixed Integer Programming Model and
develop a Charging Routing Heuristic and a Local Search Heuristic
based on the Inject-Eject routine with different insertion methods. All
heuristics are tested on real data instances.
Abstract: IEEE 802.16 (WiMAX) aims to present high speed
wireless access to cover wide range coverage. The base station (BS)
and the subscriber station (SS) are the main parts of WiMAX.
WiMAX uses either Point-to-Multipoint (PMP) or mesh topologies.
In the PMP mode, the SSs connect to the BS to gain access to the
network. However, in the mesh mode, the SSs connect to each other
to gain access to the BS.
The main components of QoS management in the 802.16 standard
are the admission control, buffer management and packet scheduling.
In this paper, we use QualNet 5.0.2 to study the performance of
different scheduling schemes, such as WFQ, SCFQ, RR and SP when
the numbers of SSs increase. We find that when the number of SSs
increases, the average jitter and average end-to-end delay is increased
and the throughput is reduced.
Abstract: The work studied the effect of germination on
proximate, phenol and flavonoid content and antioxidant activities
(AOA) of African Yam been (AYB). Germination was done in
controlled dark chamber (100% RH, 28oC). The proximate, phenol
and flavonoid content and antioxidant activities before and after
germination were investigated. The crude protein, moisture, and
crude fiber content of germinated AYB were significantly higher
(P
Abstract: Fluid viscous damping systems are well suited for
many air vehicles subjected to shock and vibration. These damping
system work with the principle of viscous fluid throttling through the
orifice to create huge pressure difference between compression and
rebound chamber and obtain the required damping force. One
application of such systems is its use in aircraft door system to
counteract the door’s velocity and safely stop it. In exigency
situations like crash or emergency landing where the door doesn’t
open easily, possibly due to unusually tilting of fuselage or some
obstacles or intrusion of debris obstruction to move the parts of the
door, such system can be combined with other systems to provide
needed force to forcefully open the door and also securely stop it
simultaneously within the required time i.e. less than 8 seconds. In
the present study, a hydraulic system called snubber along with other
systems like actuator, gas bottle assembly which together known as
emergency power assist system (EPAS) is designed, built and
experimentally studied to check the magnitude of angular velocity,
damping force and time required to effectively open the door.
Whenever needed, the gas pressure from the bottle is released to
actuate the actuator and at the same time pull the snubber’s piston to
operate the emergency opening of the door. Such EPAS installed in
the suspension arm of the aircraft door is studied explicitly changing
parameters like orifice size, oil level, oil viscosity and bypass valve
gap and its spring of the snubber at varying temperature to generate
the optimum design case. Comparative analysis of the EPAS at
several cases is done and conclusions are made. It is found that
during emergency condition, the system opening time and angular
velocity, when snubber with 0.3mm piston and shaft orifice and
bypass valve gap of 0.5 mm with its original spring is used, shows
significant improvement over the old ones.
Abstract: Precise capture of plantar 3D surface of the foot at the
loading gait phases on rigid substrates was found to be valuable for
the assessment of the physiology, health and problems of the feet.
Photogrammetry, a precision 3D spatial data capture technique is
suitable for this type of dynamic application. In this research, the
technique is utilised to study the plantar deformation as a result of
having a strip of kinesiology tape on the plantar surface during the
loading phase of gait. For this pilot study, one healthy adult male
subject was recruited under the University’s human research ethics
guidelines for this preliminary study. The 3D plantar deformation
data with and without applying the tape were analysed. The results
and analyses are presented together with detailed findings.
Abstract: Effect of biopesticide from wood vinegar and
extracted substances from 3 medicinal plants such as: non taai yak
(Stemona tuberosa Lour), boraphet (Tinospora crispa Mier) and
derris (Derris elliptica Roxb) were tested on the age five years of
pomelo. The selected pomelo was carried out for insects’ pest control
and its quality. The experimental site was located at farmer’s orchard
in Phichit Province, Thailand. This study was undertaken during the
drought season (December to March). The extracted from plants and
wood vinegar were evaluated in 6 treatments: 1) water as control; 2)
wood vinegar; 3) S. tuberosa Lour; 4) T. crispa Mier; 5) D. elliptica
Roxb; 6) mixed (wood vinegar + S. tuberosa Lour + T. crispa Mier +
D. elliptica Roxb). The experiment was RCB with 6 treatments and 3
replications per treatment. The results showed that T. crispa Mier was
the highest effectiveness for reduction population of thrips
(Scirtothrips dorsalis Hood) and citrus leaf miner (Phyllocnistis
citrella Stainton) at 14.10 and 15.37 respectively, followed by
treatment of mixed, D. elliptica Roxb, S. tuberosa Lour and wood
vinegar with significance different. Additionally, T. crispa Mier
promoted the high quality of harvested pomelo in term of thickness
of skin at 12.45 mm and S. tuberosa Lour gave the high quality of the
pomelo in term of firmness (276.5 kg/cm2) and brix (11.0%).
Abstract: The objective of this study was to assess whether
living in proximity to a roofing fiber cement factory in southern
Thailand was associated with physical, mental, social, and spiritual
health domains measured in a self-reported health risk assessment
(HRA) questionnaire. A cross-sectional study was conducted among
community members divided into two groups: near population (living
within 0-2km of factory) and far population (living within 2-5km of
factory) (N=198). A greater proportion of those living far from the
factory (65.34%) reported physical health problems than the near
group (51.04%) (p =0.032). This study has demonstrated that the near
population group had higher proportion of participants with positive
ratings on mental assessment (30.34%) and social health impacts
(28.42%) than far population group (10.59% and 16.67%,
respectively) (p
Abstract: Governments collect and produce large amounts of
data. Increasingly, governments worldwide have started to implement
open data initiatives and also launch open data portals to enable the
release of these data in open and reusable formats. Therefore, a large
number of open data repositories, catalogues and portals have been
emerging in the world. The greater availability of interoperable and
linkable open government data catalyzes secondary use of such data,
so they can be used for building useful applications which leverage
their value, allow insight, provide access to government services, and
support transparency. The efficient development of successful open
data portals makes it necessary to evaluate them systematic, in order
to understand them better and assess the various types of value they
generate, and identify the required improvements for increasing this
value. Thus, the attention of this paper is directed particularly to the
field of open data portals. The main aim of this paper is to compare
the selected open data portals on the national level using content
analysis and propose a new evaluation framework, which further
improves the quality of these portals. It also establishes a set of
considerations for involving businesses and citizens to create eservices
and applications that leverage on the datasets available from
these portals.