Abstract: The aim of this study was to investigate the influence
of reaction temperature and wheat straw moisture content on the
pyrolysis product yields, in the temperature range of 475-575 °C.
Samples of straw with moisture contents from 1.5 wt % to 15.0 wt %
were fed to a bench scale Pyrolysis Centrifuge Reactor (PCR). The
experimental results show that the changes in straw moisture content
have no significant effect on the distribution of pyrolysis product
yields. The maximum bio-oil yields approximately 60 (wt %, on dry
ash free feedstock basis) was observed around 525 °C - 550 °C for all
straw moisture levels. The water content in the wet straw bio-oil was
the highest. The heating value of bio-oil and solid char were
measured and the percentages of its energy distribution were
calculated. The energy distributions of bio-oil, char and gas were 56-
69 % 24-33 %, and 2-19 %, respectively.
Abstract: Today air-core coils (ACC) are a viable alternative to
ferrite-core coils in a range of applications due to their low induction
effect. An analytical study was carried out and the results were used as
a guide to understand the relationship between the magnet-coil
distance and the resulting attractive magnetic force. Four different
ACC models were fabricated for experimental study. The variation in
the models included the dimensions, the number of coil turns and the
current supply to the coil. Comparison between the analytical and
experimental results for all the models shows an average discrepancy
of less than 10%. An optimized ACC design was selected for the
scanner which can provide maximum magnetic force.
Abstract: During the last decade Panicum virgatum, known as
Switchgrass, has been broadly studied because of its remarkable
attributes as a substitute pasture and as a functional biofuel source.
The objective of this investigation was to establish soil suitability for
Switchgrass in the State of Mississippi. A linear weighted additive
model was developed to forecast soil suitability. Multicriteria
analysis and Sensitivity analysis were utilized to adjust and optimize
the model. The model was fit using seven years of field data
associated with soils characteristics collected from Natural Resources
Conservation System - United States Department of Agriculture
(NRCS-USDA). The best model was selected by correlating
calculated biomass yield with each model's soils-based output for
Switchgrass suitability. Coefficient of determination (r2) was the
decisive factor used to establish the 'best' soil suitability model.
Coefficients associated with the 'best' model were implemented
within a Geographic Information System (GIS) to create a map of
relative soil suitability for Switchgrass in Mississippi. A Geodatabase
associated with soil parameters was built and is available for future
Geographic Information System use.
Abstract: The aim of this study is to develop mathematical
relationships for the performance parameter brake thermal efficiency
(BTE) and emission parameter nitrogen oxides (NOx) for the various
esters of vegetable oils used as CI engine fuel. The BTE is an
important performance parameter defining the ability of engine to
utilize the energy supplied and power developed similarly it is
indication of efficiency of fuels used. The esters of cottonseed oil,
soybean oil, jatropha oil and hingan oil are prepared using
transesterification process and characterized for their physical and
main fuel properties including viscosity, density, flash point and
higher heating value using standard test methods. These esters are
tried as CI engine fuel to analyze the performance and emission
parameters in comparison to diesel. The results of the study indicate
that esters as a fuel does not differ greatly with that of diesel in
properties. The CI engine performance with esters as fuel is in line
with the diesel where as the emission parameters are reduced with the
use of esters.
The correlation developed between BTE and brake power(BP),
gross calorific value(CV), air-fuel ratio(A/F), heat carried away by
cooling water(HCW). Another equation is developed between the
NOx emission and CO, HC, smoke density (SD), exhaust gas
temperature (EGT). The equations are verified by comparing the
observed and calculated values which gives the coefficient of
correlation of 0.99 and 0.96 for the BTE and NOx equations
respectively.
Abstract: In this content analysis research note the aim was to explore to how sustainability and especially environmental issues are conveyed into environmental items in annual reports and disclosures. As The Global Reporting Initiative (GRI) is a globally wide multistakeholder process, the enterprises using voluntarily GRI framework are considered to be aware of sustainability and environmental concerns. The findings were that although these enterprises included in an environmentally sensitive industry sector and had special capabilities to consider environmental issues there were few GRIreporting enterprises presented substantially detailed environmental items in audited financial statements. There were only slight differences between publishing years 2008 and 2009 - the beginning years of economic turmoil. The environmental issues seemed not to be considered substantial enough for financial reporting as a basis for concerning investment or voting decisions.
Abstract: Theexperiment was carried out with 2x5 male Merino
lambs raised under intensive conditions to investigate the effect of
dietary calcium soap of linseed oil on the color and fatty acid
composition of longissimusdorsi muscle. Control lambs fed a basal
diet and the experimental lambs consumed a diet supplemented with
3% calcium soap of linseed oil. The color values (L*, a*, b* a*/b*
and chroma) were not influenced by dietary treatment. The MUFA
proportion reduced, SFA and PUFA content did not alter. As
expected, the linolenic (C18:3 n3) and thusthe n-3 content
significantly improved by linseed supplement (0.47 and 0.81; 0.78
and 1.16 in control and in experimental samples, respectively). Other
n-3 and n-6 fatty acids had similar valuestocontrol samples. The n-
6/n-3 ratio was significantly narrower in the experimental group (6.31
vs. 9.38) but the P/S ratio did not differ betweenthe two groups.In
conclusion calcium soap of linseed oil seems to be a suitable
supplement form of n-3 fatty acids to improve the nutritive value of
lamb meat.
Abstract: The induction hardening machines are utilized in
the industries which modify machine parts and tools needed to
achieve high ware resistance. This paper describes the model of
induction heating process design of inverter circuit and the results
of induction surface hardening of heating coil. In the design of
heating coil, the shape and the turn numbers of the coil are very
important design factors because they decide the overall operating
performance of induction heater including resonant frequency, Q
factor, efficiency and power factor. The performance will be tested
by experiments in some cases high frequency induction hardening
machine.
Abstract: The development of biomimetic micro-aerial-vehicles
(MAVs) with flapping wings is the future trend in military/domestic
field. The successful flight of MAVs is strongly related to the
understanding of unsteady aerodynamic performance of low Reynolds
number airfoils under dynamic flapping motion. This study explored
the effects of flapping frequency, stroke amplitude, and the inclined
angle of stroke plane on lift force and thrust force of a bio-inspiration
corrugated airfoil with 33 full factorial design of experiment and
ANOVA analysis. Unsteady vorticity flows over a corrugated thin
airfoil executing flapping motion are computed with time-dependent
two-dimensional laminar incompressible Reynolds-averaged
Navier-Stokes equations with the conformal hybrid mesh. The tested
freestream Reynolds number based on the chord length of airfoil as
characteristic length is fixed of 103. The dynamic mesh technique is
applied to model the flapping motion of a corrugated airfoil. Instant
vorticity contours over a complete flapping cycle clearly reveals the
flow mechanisms for lift force generation are dynamic stall, rotational
circulation, and wake capture. The thrust force is produced as the
leading edge vortex shedding from the trailing edge of airfoil to form a
reverse von Karman vortex. Results also indicated that the inclined
angle is the most significant factor on both the lift force and thrust
force. There are strong interactions between tested factors which mean
an optimization study on parameters should be conducted in further
runs.
Abstract: This work presents the first results from the long-term experiment, which is focused on the impact of intensive rainfall and long period of drought on microbial activities in soil. Fifteen lysimeters were prepared in the area of our interest. This area is a protection zone of underground source of drinking water. These lysimeters were filed with topsoil and subsoil collected in this area and divided into two groups. These groups differ in fertilization and amount of water received during the growing season. Amount of microbial biomass and leaching of mineral nitrogen and phosphates were chosen as main indicators of microbial activities in soil. Content of mineral nitrogen and phosphates was measured in soil solution, which was collected from each lysimeters. Amount of microbial biomass was determined in soil samples that were taken from the lysimeters before and after the long period of drought and intensive rainfall.
Abstract: The study of soil for agriculture purposes has
remained the main focus of research since the beginning of civilization as humans- food related requirements remained closely linked with the soil. The study of soil has generated an interest
among the researchers for very similar other reasons including transmission, reflection and refraction of signals for deploying
wireless underground sensor networks or for the monitoring of objects on (or in ) soil in the form of better understanding of soil
electromagnetic characteristics properties. The moisture content has
been very instrumental in such studies as it decides on the resistance of the soil, and hence the attenuation on signals traveling through soil
or the attenuation the signals may suffer upon their impact on soil. This work is related testing and characterizing a measurement circuit
meant for the detection of moisture level content in soil.
Abstract: This paper presents a mean for reducing the torque
variation during the revolution of a vertical-axis wind turbine
(VAWT) by increasing the blade number. For this purpose, twodimensional
CDF analysis have been performed on a straight-bladed
Darreius-type rotor. After describing the computational model, a
complete campaign of simulations based on full RANS unsteady
calculations is proposed for a three, four and five-bladed rotor
architecture characterized by a NACA 0025 airfoil. For each
proposed rotor configuration, flow field characteristics are
investigated at several values of tip speed ratio, allowing a
quantification of the influence of blade number on flow geometric
features and dynamic quantities, such as rotor torque and power.
Finally, torque and power curves are compared for the analyzed
architectures, achieving a quantification of the effect of blade number
on overall rotor performance.
Abstract: Computer based geostatistical methods can offer effective data analysis possibilities for agricultural areas by using
vectorial data and their objective informations. These methods will help to detect the spatial changes on different locations of the large
agricultural lands, which will lead to effective fertilization for optimal yield with reduced environmental pollution. In this study, topsoil (0-20 cm) and subsoil (20-40 cm) samples were taken from a
sugar beet field by 20 x 20 m grids. Plant samples were also collected
from the same plots. Some physical and chemical analyses for these
samples were made by routine methods. According to derived variation coefficients, topsoil organic matter (OM) distribution was more than subsoil OM distribution. The highest C.V. value of
17.79% was found for topsoil OM. The data were analyzed
comparatively according to kriging methods which are also used
widely in geostatistic. Several interpolation methods (Ordinary,Simple and Universal) and semivariogram models (Spherical,
Exponential and Gaussian) were tested in order to choose the suitable
methods. Average standard deviations of values estimated by simple
kriging interpolation method were less than average standard
deviations (topsoil OM ± 0.48, N ± 0.37, subsoil OM ± 0.18) of measured values. The most suitable interpolation method was simple
kriging method and exponantial semivariogram model for topsoil,
whereas the best optimal interpolation method was simple kriging
method and spherical semivariogram model for subsoil. The results
also showed that these computer based geostatistical methods should
be tested and calibrated for different experimental conditions and semivariogram models.
Abstract: The environmental performance of rapeseed oil (RO)
and rapeseed methyl ester(RME) from winter rape as fuels produced
in Romanian agroclimate is analyzed in this paper. The proposed
methodology is life cycle assessment (LCA) and takes into
consideration the influence of grain production and agroclimatic
conditions. This study shows favorable results first for RO and then
for RME. When compared to diesel fuel, both studied biofuels show
better results in the following impact categories: Abiotic depletion
potential (ADP), Ozone layer depletion (ODP) and Photochemical
ozone creation potential (POCP).Furthermore, the environmental
performance of the two biofuels studied can be improved by
changing the type of fertilizer used and also by using biofuels instead
of diesel in the field works.
Abstract: Protection of slope and embankment from erosion has
become an important issue in Bangladesh. The constructions of
strong structures require large capital, integrated designing, high
maintenance cost. Strong structure methods have negative impact on
the environment and sometimes not function for the design period.
Plantation of vetiver system along the slopes is an alternative
solution. Vetiver not only serves the purpose of slope protection but
also adds green environment reducing pollution. Vetiver is available
in almost all the districts of Bangladesh. This paper presents the
application of vetiver system with geo-jute, for slope protection and
erosion control of embankments and slopes. In-situ shear tests have
been conducted on vetiver rooted soil system to find the shear
strength. The shear strength and effective soil cohesion of vetiver
rooted soil matrix are respectively 2.0 times and 2.1 times higher than
that of the bared soil. Similar trends have been found in direct shear
tests conducted on laboratory reconstituted samples. Field trials have
been conducted in road embankment and slope protection with
vetiver at different sites. During the time of vetiver root growth the
soil protection has been accomplished by geo-jute. As the geo-jute
degrades with time, vetiver roots grow and take over the function of
geo-jutes. Slope stability analyses showed that vegetation increase
the factor of safety significantly.
Abstract: Bentonitic material from South Aswan, Egypt was evaluated in terms of mineral-ogy and chemical composition as bleaching clay in refining of transformer oil before and after acid activation and thermal treatment followed by acid leaching using HCl and H2SO4 for different contact times. Structural modification and refining power of bento-nite were investigated during modification by means of X-ray diffraction and infrared spectroscopy. The results revealed that the activated bentonite could be used for refining of transformer oil. The oil parameters such as; dielectric strength, viscosity and flash point had been improved. The dielectric breakdown strength of used oil increased from 29 kV for used oil treated with unactivated bentonite to 74 kV after treatment with activated bentonite. Kinematic Viscosity changed from 19 to 11 mm2 /s after treatment with activated bentonite. However, flash point achieved 149 ºC.
Abstract: Recent research on seeds of bio-diesel plants like
Jatropha curcas, constituting 40-50% bio-crude oil indicates its
potential as one of the most promising alternatives to conventional
sources of energy. Also, limited studies on utilization of de-oiled cake
have revealed that Jatropha bio-waste has good potential to be used as
organic fertilizers produced via aerobic and anaerobic treatment.
However, their commercial exploitation has not yet been possible. The
present study aims at developing appropriate bio-processes and
formulations utilizing Jatropha seed cake as organic fertilizer, for
improving the growth of Polianthes tuberose L. (Tuberose). Pot
experiments were carried out by growing tuberose plants on soil
treated with composted formulations of Jatropha de-oiled cake, Farm
Yard Manure (FYM) and inorganic fertilizers were also blended in
soil. The treatment was carried out through soil amendment as well as
foliar spray. The growth and morphological parameters were
monitored for entire crop cycle.
The growth Length and number of leaves, spike length, rachis
length, number of bulb per plant and earliness of sprouting of bulb and
yield enhancement were comparable to that achieved under inorganic
fertilizer. Furthermore, performance of inorganic fertilizer also showed
an improvement when blended with composted bio-waste. These
findings would open new avenues for Jatropha based bio-wastes to be
composted and used as organic fertilizers for commercial floriculture.
Abstract: Principally, plants grown in soilless culture may be
attacked by the same pests and diseases as cultivated traditionally in
soil. The most destructive phytopathogens are fungi, such as
Phythium, Phytophthora and Fusarium, followed by viruses, bacteria
and nematodes. We investigated effect of carbon nanotube filters on
disease management of soilless culture. Tomato seedlings transplant
in plastic pots filled with a soilless media of vermiculite. The crop
irrigated and fertilized using a hydroponic nutrient solution. We used
carbon nanotube filters for nutrient solution disinfection. Our results
show that carbon nanotube filtration significantly reduces pathogens
on tomato plants. Fungal elimination (Fusarium oxysporum and
Pythium spp.) was usually successful at about 96 to 99.9% all over
the cultural season. It is seem that in tomato soilless culture,
nanofiltration constitutes a reliable method that allows control of the
development of diseases caused by pathogenic fungi
Abstract: Two Amphiphilic catalysts, iron (III) dodecylbenzene
sulfonate and nickel (II) dodecylbenzene sulfonate, were synthesized
and used in the catalytic aquathermolysis of heavy crude oil to reduce
its viscosity. The prepared catalysts exhibited good performance in
the aquathermolysis and the viscosity is reduced by ~ 78.9 % for
Egyptian heavy crude oil. The chemical and physical properties of
heavy oil both before and after reaction were investigated by FT-IR,
dynamic viscosity, molecular weight and SARA analysis. The results
indicated that the content of resin, asphaltene, average molecular
weight and sulfur content of heavy oil is reduced after the catalytic
aquathermolysis.
Abstract: Small-scale RC models of both piles and tunnel ducts
were produced as mockups of reality and loaded under soil
confinement conditionsto investigate the damage evolution of
structural RC interacting with soil. Experimental verifications usinga
3D nonlinear FE analysis program called COM3D, which was
developed at the University of Tokyo, are introduced. This analysis
has been used in practice for seismic performance assessment of
underground ducts and in-ground LNG storage tanks in consideration
of soil-structure interactionunder static and dynamic loading. Varying
modes of failure of RCpilessubjected to different magnitudes of soil
confinement were successfully reproduced in the proposed small-scale
experiments and numerically simulated as well. Analytical simulation
was applied to RC tunnel mockups under a wide variety of depth and
soil confinement conditions, and reasonable matching was confirmed.
Abstract: Pyrolysis of waste tire is one of alternative technique
to produce petrochemicals, such as light olefins, mixed C4, and monoaromatics.
Noble metals supported on acid zeolite catalysts were
reported as potential catalysts to produce the high valuable products
from waste tire pyrolysis. Especially, Pd supported on HBeta gave a
high yield of olefins, mixed C4, and mono-aromatics. Due to the high
prices of noble metals, the objective of this work was to investigate
whether or not a non-noble Ni metal can be used as a substitute of a
noble metal, Pd, supported on HBeta as a catalyst for waste tire pyrolysis.
Ni metal was selected in this work because Ni has high activity
in cracking, isomerization, hydrogenation and the ring opening of
hydrocarbons Moreover, Ni is an element in the same group as Pd
noble metal, which is VIIIB group, aiming to produce high valuable
products similarly obtained from Pd. The amount of Ni was varied as
5, 10, and 20% by weight, for comparison with a fixed 1 wt% Pd,
using incipient wetness impregnation. The results showed that as a
petrochemical-producing catalyst, 10%Ni/HBeta performed better
than 1%Pd/HBeta because it did not only produce the highest yield of
olefins and cooking gases, but the yields were also higher than
1%Pd/HBeta. 5%Ni/HBeta can be used as a substitute of
1%Pd/HBeta for similar crude production because its crude contains
the similar amounts of naphtha and saturated HCs, although it gave
no concentration of light mono-aromatics (C6-C11) in the oil. Additionally,
10%Ni/HBeta that gave high olefins and cooking gases was
found to give a fairly high concentration of the light mono-aromatics
in the oil.