Abstract: The increase in electric power demand in face of
environmental issues has intensified the participation of renewable
energy sources such as photovoltaics, in the energy matrix of various
countries. Due to their operational characteristics, they can generate
time-varying harmonic and inter-harmonic distortions. For this
reason, the application of methods of measurement based on
traditional Fourier analysis, as proposed by IEC 61000-4-7, can
provide inaccurate results. Considering the aspects mentioned herein,
came the idea of the development of this work which aims to present
the results of a comparative evaluation between a methodology
arising from the combination of the Prony method with the Kalman
filter and another method based on the IEC 61000-4-30 and IEC
61000-4-7 standards. Employed in this study were synthetic signals
and data acquired through measurements in a 50kWp photovoltaic
installation.
Abstract: Hydrogen produced by means of polymer electrolyte
membrane electrolyzer (PEME) is one of the most promising
methods due to clean and renewable energy source. In the process,
some energy loss due to mass transfer through a PEM is caused by
diffusion, electro-osmotic drag, and the pressure difference between
the cathode channel and anode channel. In PEME, water molecules
and ionic particles transferred between the electrodes from anode to
cathode, Extensive mixing of the hydrogen and oxygen at anode
channel due to gases cross-over must be avoided. In recent times the
consciousness of safety issue in high pressure PEME where the
oxygen mix with hydrogen at anode channel could create, explosive
conditions have generated a lot of concern. In this paper, the steady
state and simulation analysis of gases crossover in PEME on the
temperature and pressure effect are presented. The simulations have
been analysis in MATLAB based on the well-known Fick’s Law of
molecular diffusion. The simulation results indicated that as
temperature increases, there is a significant decrease in operating
voltage.
Abstract: Finding the optimal 3D path of an aerial vehicle under
flight mechanics constraints is a major challenge, especially when
the algorithm has to produce real time results in flight. Kinematics
models and Pythagorian Hodograph curves have been widely used
in mobile robotics to solve this problematic. The level of difficulty
is mainly driven by the number of constraints to be saturated at the
same time while minimizing the total length of the path. In this paper,
we suggest a pragmatic algorithm capable of saturating at the same
time most of dimensioning helicopter 3D trajectories’ constraints
like: curvature, curvature derivative, torsion, torsion derivative, climb
angle, climb angle derivative, positions. The trajectories generation
algorithm is able to generate versatile complex 3D motion primitives
feasible by a helicopter with parameterization of the curvature and the
climb angle. An upper ”motion primitives’ concatenation” algorithm
is presented based. In this article we introduce a new way of designing
three-dimensional trajectories based on what we call the ”Dubins
gliding symmetry conjecture”. This extremely performing algorithm
will be soon integrated to a real-time decisional system dealing with
inflight safety issues.
Abstract: Geological and tectonic framework indicates that
Bangladesh is one of the most seismically active regions in the world.
The Bengal Basin is at the junction of three major interacting plates:
the Indian, Eurasian, and Burma Plates. Besides there are many
active faults within the region, e.g. the large Dauki fault in the north.
The country has experienced a number of destructive earthquakes due
to the movement of these active faults. Current seismic provisions of
Bangladesh are mostly based on earthquake data prior to the 1990.
Given the record of earthquakes post 1990, there is a need to revisit
the design provisions of the code. This paper compares the base shear
demand of three major cities in Bangladesh: Dhaka (the capital city),
Sylhet, and Chittagong for earthquake scenarios of magnitudes
7.0MW, 7.5MW, 8.0MW, and 8.5MW using a stochastic model. In
particular, the stochastic model allows the flexibility to input region
specific parameters such as shear wave velocity profile (that were
developed from Global Crustal Model CRUST2.0) and include the
effects of attenuation as individual components. Effects of soil
amplification were analysed using the Extended Component
Attenuation Model (ECAM). Results show that the estimated base
shear demand is higher in comparison with code provisions leading to
the suggestion of additional seismic design consideration in the study
regions.
Abstract: Unsteady flow and heat transfer from a circular
cylinder in cross-flow is studied numerically. The governing
equations are solved by using finite volume method. Reynolds
number varies in range of 50 to 200; in this range flow is considered
to be laminar and unsteady. Al2O3 nanoparticle with volume fraction
in range of 5% to 20% is added to pure water. Effects of adding
nanoparticle to pure water on lift and drag coefficient and Nusselt
number is presented. Addition of Al2O3 has inconsiderable effect on
the value of drags and lift coefficient. However, it has significant
effect on heat transfer; results show that heat transfer of Al2O3
nanofluid is about 9% to 36% higher than pure water.
Abstract: A theoretical study of a humidification
dehumidification solar desalination unit has been carried out to
increase understanding the effect of weather conditions on the unit
productivity. A humidification-dehumidification (HD) solar
desalination unit has been designed to provide fresh water for
population in remote arid areas. It consists of solar water collector
and air collector; to provide the hot water and air to the desalination
chamber. The desalination chamber is divided into humidification
and dehumidification towers. The circulation of air between the two
towers is maintained by the forced convection. A mathematical
model has been formulated, in which the thermodynamic relations
were used to study the flow, heat and mass transfer inside the
humidifier and dehumidifier. The present technique is performed in
order to increase the unit performance. Heat and mass balance has
been done and a set of governing equations has been solved using the
finite difference technique. The unit productivity has been calculated
along the working day during the summer and winter sessions and
has compared with the available experimental results. The average
accumulative productivity of the system in winter has been ranged
between 2.5 to 4 (kg/m2)/day, while the average summer productivity
has been found between 8 to 12 (kg/m2)/day.
Abstract: The current statuses of lifetime test of LaB6 hollow
cathode at the Lanzhou Institute of Physics (LIP), China, was
described. 5A LaB6 hollow cathode was design for LIPS-200 40mN
Xenon ion thruster, and it could be used for LHT-100 80 mN Hall
thruster, too. Life test of the discharge and neutralizer modes of LHC-5
hollow cathode were stared in October 2011, and cumulative operation
time reached 17,300 and 16,100 hours in April 2015, respectively. The
life of cathode was designed more than 11,000 hours. Parameters of
discharge and key structure dimensions were monitored in different
stage of life test indicated that cathodes were health enough. The test
will continue until the cathode cannot work or operation parameter is
not in normally. The result of the endurance test of cathode
demonstrated that the LaB6 hollow cathode is satisfied for the required
of thruster in life and performance.
Abstract: This paper is concerned with the ways in which
Assisted Reproductive Technologies (ARTs) affect women’s lives
and perceptions regarding their infertility, contraception and
reproductive health. The paper is based on a qualitative feminist
survey study to explore and analyze issues arising from the use of
ARTs by women in New Delhi, the capital of India. A rapid growth in
the number of fertility clinics has been noticed recently. A critical
analysis of interviews revealed that these technologies are used and
developed for making profits at the cost of women’s lives. In this
way, these technologies are influencing and changing the traditional
patterns of motherhood requiring a rethinking about new ways of
reproduction introduced through the use of ARTs.
Abstract: Chatter vibrations, occurring during cutting process,
cause vibration between the cutting tool and workpiece, which
deteriorates surface roughness and reduces tool life. The purpose of
this study is to investigate the influence of cutting parameters and
tool construction on surface roughness and vibration in turning of
aluminum alloy AA2024. A new design of cutting tool is proposed,
which is filled up with epoxy granite in order to improve damping
capacity of the tool. Experiments were performed at the lathe using
carbide cutting insert coated with TiC and two different cutting tools
made of AISI 5140 steel. Taguchi L9 orthogonal array was applied to
design of experiment and to optimize cutting conditions. By the help
of signal-to-noise ratio and analysis of variance the optimal cutting
condition and the effect of the cutting parameters on surface
roughness and vibration were determined. Effectiveness of Taguchi
method was verified by confirmation test. It was revealed that new
cutting tool with epoxy granite has reduced vibration and surface
roughness due to high damping properties of epoxy granite in
toolholder.
Abstract: Green concrete are generally composed of recycling
materials as hundred or partial percent substitutes for aggregate,
cement, and admixture in concrete. To reduce greenhouse gas
emissions, efforts are needed to develop environmentally friendly
construction materials. Using of fly ash based geopolymer as an
alternative binder can help reduce CO2 emission of concrete. The
binder of geopolymer concrete is different from the ordinary Portland
cement concrete. Geopolymer Concrete specimens were prepared
with different concentration of NaOH solution M10, M14, and, M16
and cured at 60ºC in duration of 24 hours and 8 hours, in addition to
the curing in direct sunlight. Thus, it is necessary to study the effects
of the geopolymer binder on the behavior of concrete. Concrete is
made by using geopolymer technology is environmental friendly and
could be considered as part of the sustainable development. In this
study, the Local Alkaline Activator in Egypt and crashed stone as
coarse aggregate in fly ash based-geopolymer concrete was
investigated. This paper illustrates the development of mechanical
properties. Since the gained compressive strength for geopolymer
concrete at 28 days was in the range of 22.5MPa – 43.9MPa.
Abstract: Local steel slag is produced as a by-product during the
oxidation of steel pellets in an electric arc furnace. Using local steel
slag waste as a hundred substitutes of crashed stone in construction
materials would resolve the environmental problems caused by the
large-scale depletion of the natural sources of crashed stone. This
paper reports the experimental study to investigate the influence of a
hundred replacement of crashed stone as a coarse aggregate with
local steel slag, on the fresh and hardened geopolymer concrete
properties. The investigation includes traditional testing of hardening
concrete, for selected mixes of cement and geopolymer concrete. It
was found that local steel slag as a coarse aggregate enhanced the
slump test of the fresh state of cement and geopolymer concretes.
Nevertheless, the unit weight of concretes was affected. Meanwhile,
the good performance was observed when fly ash used as geopolymer
concrete based.
Abstract: This study presents experimental and optimization of
nanoparticle mass concentration and heat input based on the total
thermal resistance (Rth) of loop heat pipe (LHP), employed for PCCPU
cooling. In this study, silica nanoparticles (SiO2) in water with
particle mass concentration ranged from 0% (pure water) to 1% is
considered as the working fluid within the LHP. The experimental
design and optimization is accomplished by the design of
experimental tool, Response Surface Methodology (RSM). The
results show that the nanoparticle mass concentration and the heat
input have significant effect on the Rth of LHP. For a given heat
input, the Rth is found to decrease with the increase of the
nanoparticle mass concentration up to 0.5% and increased thereafter.
It is also found that the Rth is decreased when the heat input is
increased from 20W to 60W. The results are optimized with the
objective of minimizing the Rth, using Design-Expert software, and
the optimized nanoparticle mass concentration and heat input are
0.48% and 59.97W, respectively, the minimum thermal resistance
being 2.66 (ºC/W).
Abstract: The steady flow of a second order fluid through
constricted tube with slip velocity at wall is modeled and analyzed
theoretically. The governing equations are simplified by implying no
slip in radial direction. Based on Karman Pohlhausen procedure
polynomial solution for axial velocity profile is presented.
Expressions for pressure gradient, shear stress, separation and
reattachment points, and radial velocity are also calculated. The
effect of slip and no slip velocity on magnitude velocity, shear stress,
and pressure gradient are discussed and depicted graphically. It is
noted that when Reynolds number increases magnitude velocity of
the fluid decreases in both slip and no slip conditions. It is also found
that the wall shear stress, separation, and reattachment points are
strongly affected by Reynolds number.
Abstract: A clay soil classified as A-7-6 and CH soil according
to AASHTO and unified soil classification system respectively, was
stabilized using A-3 soil (AASHTO soil classification system). The
clay soil was replaced with 0%, 10%, 20%, to 100% A-3 soil,
compacted at both British Standard Light (BSL) and British Standard
Heavy (BSH) compaction energy levels and using Unconfined
Compressive Strength (UCS) as evaluation criteria. The Maximum
Dry Density (MDD) of the treated soils at both the BSL and BSH
compaction energy levels showed increase from 0% to 40% A-3 soil
replacement after which the values reduced to 100% replacement.
The trend of the Optimum Moisture Content (OMC) with varied A-3
soil replacement was similar to that of MDD but in a reversed order.
The OMC reduced from 0% to 40% A-3 soil replacement after which
the values increased to 100% replacement. This trend was attributed
to the observed reduction in void ratio from 0% to 40% replacement
after which the void ratio increased to 100% replacement. The
maximum UCS for the soil at varied A-3 soil replacement increased
from 272 and 770 kN/m2 for BSL and BSH compaction energy level
at 0% replacement to 295 and 795 kN/m2 for BSL and BSH
compaction energy level respectively at 10% replacement after which
the values reduced to 22 and 60 kN/m2 for BSL and BSH compaction
energy level respectively at 70% replacement. Beyond 70%
replacement, the mixtures could not be moulded for UCS test.
Abstract: In this paper, we present an application of Riemannian
geometry for processing non-Euclidean image data. We consider the
image as residing in a Riemannian manifold, for developing a new
method to brain edge detection and brain extraction. Automating this
process is a challenge due to the high diversity in appearance brain
tissue, among different patients and sequences. The main contribution, in this paper, is the use of an edge-based
anisotropic diffusion tensor for the segmentation task by integrating
both image edge geometry and Riemannian manifold (geodesic,
metric tensor) to regularize the convergence contour and extract
complex anatomical structures. We check the accuracy of the
segmentation results on simulated brain MRI scans of single
T1-weighted, T2-weighted and Proton Density sequences. We
validate our approach using two different databases: BrainWeb
database, and MRI Multiple sclerosis Database (MRI MS DB). We
have compared, qualitatively and quantitatively, our approach with
the well-known brain extraction algorithms. We show that using
a Riemannian manifolds to medical image analysis improves the
efficient results to brain extraction, in real time, outperforming the
results of the standard techniques.
Abstract: In this study, we have collected cases with adipocere
formation, which were from the South Delhi region (average room
temperature 27-390C) and autopsied at our centre. Details of the
circumstances of the death, cause and time of death, surrounding
environment and demographic profile of the deceased were taken into
account. Total 16 cases were included in this study. Adipocere
formation was predominantly present over cheeks, shoulder, breast,
flanks, buttocks, and thighs. Out of 16, 11 cases were found in a dry
atmosphere, 5 cases were brought from the water. There were 5 cases
in which adipocere formation was seen in less than 2 days, and
among them, in 1 case, as early as one day. This study showed that
adipocere formation can be seen as early as 1 day in a hot and humid
environment.
Abstract: Red pepper (Capsicum annum L.) has long been
recognized as a good source of antioxidants, being rich in ascorbic
acid and other phytochemicals. In Turkish cuisine red pepper is
sometimes consumed raw in salads and baked as a garnish, but its
most wide consumption type is red pepper paste. The processing of
red pepper into pepper paste includes various thermal treatment steps
such as heating and pasteurizing. There are reports demonstrating an
enhancement or reduction in antioxidant activity of vegetables after
thermal treatment. So this study was conducted to investigate the
total phenolic, ascorbic acid and total carotenoids as well as free
radical scavenging activity of raw red pepper and various red pepper
pastes obtainable on the market. The samples were analyzed for
radical-scavenging activity (RSA) and total polyphenol (TP) content
using 1,1-diphenyl-2-picrylhydrazyl (DPPH) and Folin-Ciocalteu
methods, respectively. Total carotenoids and ascorbic acid contents
were determined spectrophotometrically. Results suggest that hot
pepper paste contained significantly (P0.05) difference in RSA, ascorbic acid and total carotenoids
content between sweet and hot red pepper paste products. It is
concluded that the red pepper paste, that has a wide range of
consumption in Turkish cuisine, presents a good dose of phenolic
compounds and antioxidant capacity and it should be regarded as a
functional food.
Abstract: The main issue in designing a wireless sensor network
(WSN) is the finding of a proper routing protocol that complies with
the several requirements of high reliability, short latency, scalability,
low power consumption, and many others. This paper proposes a
novel routing algorithm that complies with these design
requirements. The new routing protocol divides the WSN into several subnetworks
and each sub-network is divided into several clusters. This
division is designed to reduce the number of radio transmission and
hence decreases the power consumption. The network division may
be changed dynamically to adapt with the network changes and
allows the realization of the design requirements.
Abstract: Three purified diets were formulated using fish meal,
soya bean, wheat flour, palm oil, minerals and maltose. The
carbohydrate in the diets was increased from 5 to 15% by changing
the cellulose content to study the effect of dietary carbohydrate level
on the growth parameters of Nile tilapia Oreochromis niloticus. The
protein and the lipid contents were kept constant in all the diets. The
results showed that, weight gain, protein efficiency ratio, net protein
utilisation and hepatosomatic index of fish fed the diet containing
15% cellulose were the lowest among all groups. Addition, the fish
fed the diet containing 5% cellulose had the best specific growth rate,
and food conversion ratio. While, there was no effect of the dietary
cellulose levels on condition factor and survival rate. These results
indicate that Nile tilapia fingerlings are able to utilize dietary
cellulose does not exceed 10% in their feed for optimum growth.
Abstract: The aim of this study was to investigate the
photocatalytic activity of polycrystalline phases of bismuth tungstate
of formula Bi2WO6. Polycrystalline samples were elaborated using a
coprecipitation technique followed by a calcination process at
different temperatures (300, 400, 600 and 900°C). The obtained
polycrystalline phases have been characterized by X-ray diffraction
(XRD), scanning electron microscopy (SEM), and transmission
electron microscopy (TEM). Crystal cell parameters and cell volume
depend on elaboration temperature. High-resolution electron
microscopy images and image simulations, associated with X-ray
diffraction data, allowed confirming the lattices and space groups
Pca21. The photocatalytic activity of the as-prepared samples was
studied by irradiating aqueous solutions of Rhodamine B, associated
with Bi2WO6 additives having variable crystallite sizes. The
photocatalytic activity of such bismuth tungstates increased as the
crystallite sizes decreased. The high specific area of the
photocatalytic particles obtained at 300°C seems to condition the
degradation kinetics of RhB.