Abstract: We present our ongoing work on the development
of a new quadrotor aerial vehicle which has a tilt-wing
mechanism. The vehicle is capable of take-off/landing in vertical flight mode (VTOL) and flying over long distances in horizontal flight mode. Full dynamic model of the vehicle is derived using
Newton-Euler formulation. Linear and nonlinear controllers for
the stabilization of attitude of the vehicle and control of its
altitude have been designed and implemented via simulations. In particular, an LQR controller has been shown to be quite
effective in the vertical flight mode for all possible yaw angles. A sliding mode controller (SMC) with recursive nature has also
been proposed to stabilize the vehicle-s attitude and altitude. Simulation results show that proposed controllers provide
satisfactory performance in achieving desired maneuvers.
Abstract: This paper presents a systematic procedure for modelling and simulation of a power system installed with a power system stabilizer (PSS) and a flexible ac transmission system (FACTS)-based controller. For the design purpose, the model of example power system which is a single-machine infinite-bus power system installed with the proposed controllers is developed in MATLAB/SIMULINK. In the developed model synchronous generator is represented by model 1.1. which includes both the generator main field winding and the damper winding in q-axis so as to evaluate the impact of PSS and FACTS-based controller on power system stability. The model can be can be used for teaching the power system stability phenomena, and also for research works especially to develop generator controllers using advanced technologies. Further, to avoid adverse interactions, PSS and FACTS-based controller are simultaneously designed employing genetic algorithm (GA). The non-linear simulation results are presented for the example power system under various disturbance conditions to validate the effectiveness of the proposed modelling and simultaneous design approach.
Abstract: Dual motor drives fed by single inverter is
purposely designed to reduced size and cost with respect to
single motor drives fed by single inverter. Previous researches
on dual motor drives only focus on the modulation and the
averaging techniques. Only a few of them, study the
performance of the drives based on different speed controller
other than Proportional and Integrator (PI) controller. This
paper presents a detailed comparative study on fuzzy rule-base
in Fuzzy Logic speed Controller (FLC) for Dual Permanent
Magnet Synchronous Motor (PMSM) drives. Two fuzzy speed
controllers which are standard and simplified fuzzy speed
controllers are designed and the results are compared and
evaluated. The standard fuzzy controller consists of 49 rules
while the proposed controller consists of 9 rules determined by
selecting the most dominant rules only. Both designs are
compared for wide range of speed and the robustness of both
controllers over load disturbance changes is tested to
demonstrate the effectiveness of the simplified/reduced rulebase.
Abstract: Evolutionary robotics is concerned with the design of
intelligent systems with life-like properties by means of simulated
evolution. Approaches in evolutionary robotics can be categorized
according to the control structures that represent the behavior and the
parameters of the controller that undergo adaptation. The basic idea
is to automatically synthesize behaviors that enable the robot to
perform useful tasks in complex environments. The evolutionary
algorithm searches through the space of parameterized controllers
that map sensory perceptions to control actions, thus realizing a
specific robotic behavior. Further, the evolutionary algorithm
maintains and improves a population of candidate behaviors by
means of selection, recombination and mutation. A fitness function
evaluates the performance of the resulting behavior according to the
robot-s task or mission. In this paper, the focus is in the use of
genetic algorithms to solve a multi-objective optimization problem
representing robot behaviors; in particular, the A-Compander Law is
employed in selecting the weight of each objective during the
optimization process. Results using an adaptive fitness function show
that this approach can efficiently react to complex tasks under
variable environments.
Abstract: State Dependent Riccati Equation (SDRE) approach is
a modification of the well studied LQR method. It has the capability of being applied to control nonlinear systems. In this paper the technique
has been applied to control the single inverted pendulum (SIP) which represents a rich class of nonlinear underactuated systems. SIP
modeling is based on Euler-Lagrange equations. A procedure is developed
for judicious selection of weighting parameters and constraint handling. The controller designed by SDRE technique here gives better results than existing controllers designed by energy based techniques.
Abstract: In this paper; we are interested in dynamic modelling of quadrotor while taking into account the high-order nonholonomic constraints as well as the various physical phenomena, which can influence the dynamics of a flying structure. These permit us to introduce a new state-space representation and new control scheme. We present after the development and the synthesis of a stabilizing control laws design based on sliding mode in order to perform best tracking results. It ensures locally asymptotic stability and desired tracking trajectories. Nonlinear observer is then synthesized in order to estimate the unmeasured states and the effects of the external disturbances such as wind and noise. Finally simulation results are also provided in order to illustrate the performances of the proposed controllers.
Abstract: This paper attempts to model and design a simple
fuzzy logic controller with Variable Reference. The Variable
Reference (VR) is featured as an adaptability element which is
obtained from two known variables – desired system-input and actual
system-output. A simple fuzzy rule-based technique is simulated to
show how the actual system-input is gradually tuned in to a value
that closely matches the desired input. The designed controller is
implemented and verified on a simple heater which is controlled by
PIC Microcontroller harnessed by a code developed in embedded C.
The output response of the PIC-controlled heater is analyzed and
compared to the performances by conventional fuzzy logic
controllers. The novelty of this work lies in the fact that it gives
better performance by using less number of rules compared to
conventional fuzzy logic controllers.
Abstract: Saccharomyces cerevisiae (baker-s yeast) can exhibit
sustained oscillations during the operation in a continuous bioreactor
that adversely affects its stability and productivity. Because of
heterogeneous nature of cell populations, the cell population balance
models can be used to capture the dynamic behavior of such cultures.
In this paper an unstructured, segregated model is used which is
based on population balance equation(PBE) and then in order to
simulation, the 4th order Rung-Kutta is used for time dimension and
three methods, finite difference, orthogonal collocation on finite
elements and Galerkin finite element are used for discretization of the
cell mass domain. The results indicate that the orthogonal collocation
on finite element not only is able to predict the oscillating behavior of
the cell culture but also needs much little time for calculations.
Therefore this method is preferred in comparison with other methods.
In the next step two controllers, a globally linearizing control (GLC)
and a conventional proportional-integral (PI) controller are designed
for controlling the total cell mass per unit volume, and performances
of these controllers are compared through simulation. The results
show that although the PI controller has simpler structure, the GLC
has better performance.
Abstract: This paper presents a design method of self-tuning
Quantitative Feedback Theory (QFT) by using improved deadbeat
control algorithm. QFT is a technique to achieve robust control with
pre-defined specifications whereas deadbeat is an algorithm that
could bring the output to steady state with minimum step size.
Nevertheless, usually there are large peaks in the deadbeat response.
By integrating QFT specifications into deadbeat algorithm, the large
peaks could be tolerated. On the other hand, emerging QFT with
adaptive element will produce a robust controller with wider
coverage of uncertainty. By combining QFT-based deadbeat
algorithm and adaptive element, superior controller that is called selftuning
QFT-based deadbeat controller could be achieved. The output
response that is fast, robust and adaptive is expected. Using a grain
dryer plant model as a pilot case-study, the performance of the
proposed method has been evaluated and analyzed. Grain drying
process is very complex with highly nonlinear behaviour, long delay,
affected by environmental changes and affected by disturbances.
Performance comparisons have been performed between the
proposed self-tuning QFT-based deadbeat, standard QFT and
standard dead-beat controllers. The efficiency of the self-tuning QFTbased
dead-beat controller has been proven from the tests results in
terms of controller’s parameters are updated online, less percentage
of overshoot and settling time especially when there are variations in
the plant.
Abstract: The objective of this paper is to compare the time
specification performance between conventional controller PID and
modern controller SMC for an inverted pendulum system. The goal is
to determine which control strategy delivers better performance with
respect to pendulum-s angle and cart-s position. The inverted
pendulum represents a challenging control problem, which
continually moves toward an uncontrolled state. Two controllers are
presented such as Sliding Mode Control (SMC) and Proportional-
Integral-Derivatives (PID) controllers for controlling the highly
nonlinear system of inverted pendulum model. Simulation study has
been done in Matlab Mfile and simulink environment shows that both
controllers are capable to control multi output inverted pendulum
system successfully. The result shows that Sliding Mode Control
(SMC) produced better response compared to PID control strategies
and the responses are presented in time domain with the details
analysis.
Abstract: A nonlinear optimal controller with a fuzzy gain
scheduler has been designed and applied to a Line-Of-Sight (LOS)
stabilization system. Use of Linear Quadratic Regulator (LQR)
theory is an optimal and simple manner of solving many control
engineering problems. However, this method cannot be utilized
directly for multigimbal LOS systems since they are nonlinear in
nature. To adapt LQ controllers to nonlinear systems at least a
linearization of the model plant is required. When the linearized
model is only valid within the vicinity of an operating point a gain
scheduler is required. Therefore, a Takagi-Sugeno Fuzzy Inference
System gain scheduler has been implemented, which keeps the
asymptotic stability performance provided by the optimal feedback
gain approach. The simulation results illustrate that the proposed
controller is capable of overcoming disturbances and maintaining a
satisfactory tracking performance.
Abstract: In the control theory one attempts to find a controller
that provides the best possible performance with respect to some
given measures of performance. There are many sorts of controllers
e.g. a typical PID controller, LQR controller, Fuzzy controller etc. In
the paper will be introduced polynomial controller with novel tuning
method which is based on the special pole placement encoding
scheme and optimization by Genetic Algorithms (GA). The examples
will show the performance of the novel designed polynomial
controller with comparison to common PID controller.
Abstract: This paper presents the optimal controller design of
the generator control unit in the aircraft power system. The adaptive
tabu search technique is applied to tune the controller parameters
until the best terminal output voltage of generator is achieved. The
output response from the system with the controllers designed by the
proposed technique is compared with those from the conventional
method. The transient simulations using the commercial software
package show that the controllers designed from the adaptive tabu
search algorithm can provide the better output performance compared
with the result from the classical method. The proposed design
technique is very flexible and useful for electrical aircraft engineers.
Abstract: In this paper, genetic algorithm (GA) opmization technique is applied to design Flexible AC Transmission System (FACTS)-based damping controllers. Two types of controller structures, namely a proportional-integral (PI) and a lead-lag (LL) are considered. The design problem of the proposed controllers is formulated as an optimization problem and GA is employed to search for optimal controller parameters. By minimizing the time-domain based objective function, in which the deviation in the oscillatory rotor speed of the generator is involved; stability performance of the system is improved. The proposed controllers are tested on a weakly connected power system subjected to different disturbances. The non-linear simulation results are presented to show the effectiveness of the proposed controller and their ability to provide efficient damping of low frequency oscillations. It is also observed that the proposed SSSC-based controllers improve greatly the voltage profile of the system under severe disturbances. Further, the dynamic performances of both the PI and LL structured FACTS-controller are analyzed at different loading conditions and under various disturbance condition as well as under unbalanced fault conditions..
Abstract: This paper presents a systematic approach for
designing Static Synchronous Series Compensator (SSSC) based
supplementary damping controllers for damping low frequency
oscillations in a single-machine infinite-bus power system. The
design problem of the proposed controller is formulated as an
optimization problem and RCGA is employed to search for optimal
controller parameters. By minimizing the time-domain based
objective function, in which the deviation in the oscillatory rotor
speed of the generator is involved; stability performance of the
system is improved. Simulation results are presented and compared
with a conventional method of tuning the damping controller
parameters to show the effectiveness and robustness of the proposed
design approach.
Abstract: Due to their high power-to-weight ratio and low cost, pneumatic actuators are attractive for robotics and automation applications; however, achieving fast and accurate control of their position have been known as a complex control problem. The paper presents a methodology for obtaining controllers that achieve high position accuracy and preserve the closed-loop characteristics over a broad operating range. Experimentation with a number of conventional (or "classical") three-term controllers shows that, as repeated operations accumulate, the characteristics of the pneumatic actuator change requiring frequent re-tuning of the controller parameters (PID gains). Furthermore, three-term controllers are found to perform poorly in recovering the closed-loop system after the application of load or other external disturbances. The key reason for these problems lies in the non-linear exchange of energy inside the cylinder relating, in particular, to the complex friction forces that develop on the piston-wall interface. In order to overcome this problem but still remain within the boundaries of classical control methods, we designed an auto selective classicaql controller so that the system performance would benefit from all three control gains (KP, Kd, Ki) according to system requirements and the characteristics of each type of controller. This challenging experimentation took place for consistent performance in the face of modelling imprecision and disturbances. In the work presented, a selective PID controller is presented for an experimental rig comprising an air cylinder driven by a variable-opening pneumatic valve and equipped with position and pressure sensors. The paper reports on tests carried out to investigate the capability of this specific controller to achieve consistent control performance under, repeated operations and other changes in operating conditions.
Abstract: This paper presents Simulation and experimental
study aimed at investigating the effectiveness of an adaptive artificial
neural network stabilizer on enhancing the damping torque of a
synchronous generator. For this purpose, a power system comprising
a synchronous generator feeding a large power system through a
short tie line is considered. The proposed adaptive neuro-control
system consists of two multi-layered feed forward neural networks,
which work as a plant model identifier and a controller. It generates
supplementary control signals to be utilized by conventional
controllers. The details of the interfacing circuits, sensors and
transducers, which have been designed and built for use in tests, are
presented. The synchronous generator is tested to investigate the
effect of tuning a Power System Stabilizer (PSS) on its dynamic
stability. The obtained simulation and experimental results verify the
basic theoretical concepts.
Abstract: In this paper, the full state feedback controllers
capable of regulating and tracking the speed trajectory are presented.
A fourth order nonlinear mean value model of a 448 kW turbocharged
diesel engine published earlier is used for the purpose.
For designing controllers, the nonlinear model is linearized and
represented in state-space form. Full state feedback controllers
capable of meeting varying speed demands of drivers are presented.
Main focus here is to investigate sensitivity of the controller to the
perturbations in the parameters of the original nonlinear model.
Suggested controller is shown to be highly insensitive to the
parameter variations. This indicates that the controller is likely
perform with same accuracy even after significant wear and tear of
engine due to its use for years.
Abstract: This paper presents the use of anti-sway angle control
approaches for a two-dimensional gantry crane with disturbances
effect in the dynamic system. Delayed feedback signal (DFS) and
proportional-derivative (PD)-type fuzzy logic controller are the
techniques used in this investigation to actively control the sway
angle of the rope of gantry crane system. A nonlinear overhead
gantry crane system is considered and the dynamic model of the
system is derived using the Euler-Lagrange formulation. A complete
analysis of simulation results for each technique is presented in time
domain and frequency domain respectively. Performances of both
controllers are examined in terms of sway angle suppression and
disturbances cancellation. Finally, a comparative assessment of the
impact of each controller on the system performance is presented and
discussed.
Abstract: This paper features the modeling and design of a Fast
Output Sampling (FOS) Feedback control technique for the Active
Vibration Control (AVC) of a smart flexible aluminium cantilever
beam for a Single Input Single Output (SISO) case. Controllers are
designed for the beam by bonding patches of piezoelectric layer as
sensor / actuator to the master structure at different locations along
the length of the beam by retaining the first 2 dominant vibratory
modes. The entire structure is modeled in state space form using the
concept of piezoelectric theory, Euler-Bernoulli beam theory, Finite
Element Method (FEM) and the state space techniques by dividing
the structure into 3, 4, 5 finite elements, thus giving rise to three
types of systems, viz., system 1 (beam divided into 3 finite
elements), system 2 (4 finite elements), system 3 (5 finite elements).
The effect of placing the sensor / actuator at various locations along
the length of the beam for all the 3 types of systems considered is
observed and the conclusions are drawn for the best performance and
for the smallest magnitude of the control input required to control the
vibrations of the beam. Simulations are performed in MATLAB. The
open loop responses, closed loop responses and the tip displacements
with and without the controller are obtained and the performance of
the proposed smart system is evaluated for vibration control.