Abstract: In the present work, fly ash geopolymer based
composites including polyester (PES) waste were studied. Specimens
of three compositions were prepared: (a) fly ash geopolymer with 5%
PES waste; (b) fly ash geopolymer mortar with 5% PES waste; (c) fly
ash geopolymer mortar with 6.25% PES waste. Compressive and
bending strength measurements, water absorption test and
determination of thermal conductivity coefficient were performed.
The results showed that the addition of sand in a mixture of
geopolymer with 5% PES content led to higher compressive strength,
while it increased water absorption and reduced thermal conductivity
coefficient. The increase of PES addition in geopolymer mortars
resulted in a more dense structure, indicated by the increase of
strength and thermal conductivity and the decrease of water
absorption.
Abstract: The present work describes the implementation of the
Enhanced Collaborative Optimization (ECO) multilevel architecture
with a gradient-based optimization algorithm with the aim of
performing a multidisciplinary design optimization of a generic
unmanned aerial vehicle with morphing technologies. The concepts
of weighting coefficient and dynamic compatibility parameter are
presented for the ECO architecture. A routine that calculates the
aircraft performance for the user defined mission profile and vehicle’s
performance requirements has been implemented using low fidelity
models for the aerodynamics, stability, propulsion, weight, balance
and flight performance. A benchmarking case study for evaluating
the advantage of using a variable span wing within the optimization
methodology developed is presented.
Abstract: The dissimilar joint between aluminum/titanium
alloys (Al 6082 and Ti G2) were successfully achieved by CO2 laser
welding with a single pass and without filler material using the
overlap joint design. Laser welding parameters ranges combinations
were experimentally determined using Taguchi approach with the
objective of producing welded joint with acceptable welding profile
and high quality of mechanical properties. In this study a joining of
dissimilar Al 6082 / Ti G2 was resulted in three distinct regions
fusion area in the weldment. These regions are studied in terms of its
microstructural characteristics and microhardness which are directly
affecting the welding quality.
The weld metal was mainly composed of martensite alpha prime.
In two different metals in the two different sides of joint HAZ, grain
growth was detected. The microhardness of the joint distribution also
has shown microhardness increasing in the HAZ of two base metals
and a varying microhardness in fusion zone.
Abstract: The building sector is responsible, in many
industrialized countries, for about 40% of the total energy
requirements, so it seems necessary to devote some efforts in this
area in order to achieve a significant reduction of energy
consumption and of greenhouse gases emissions.
The paper presents a study aiming at providing a design
methodology able to identify the best configuration of the system
building/plant, from a technical, economic and environmentally point
of view.
Normally, the classical approach involves a building's energy
loads analysis under steady state conditions, and subsequent selection
of measures aimed at improving the energy performance, based on
previous experience made by architects and engineers in the design
team. Instead, the proposed approach uses a sequence of two wellknown
scientifically validated calculation methods (TRNSYS and
RETScreen), that allow quite a detailed feasibility analysis.
To assess the validity of the calculation model, an existing,
historical building in Central Italy, that will be the object of
restoration and preservative redevelopment, was selected as a casestudy.
The building is made of a basement and three floors, with a
total floor area of about 3,000 square meters.
The first step has been the determination of the heating and
cooling energy loads of the building in a dynamic regime by means,
which allows simulating the real energy needs of the building in
function of its use. Traditional methodologies, based as they are on
steady-state conditions, cannot faithfully reproduce the effects of
varying climatic conditions and of inertial properties of the structure.
With this model is possible to obtain quite accurate and reliable
results that allow identifying effective combinations building-HVAC
system.
The second step has consisted of using output data obtained as
input to the calculation model, which enables to compare different
system configurations from the energy, environmental and financial
point of view, with an analysis of investment, and operation and
maintenance costs, so allowing determining the economic benefit of
possible interventions.
The classical methodology often leads to the choice of
conventional plant systems, while our calculation model provides a
financial-economic assessment for innovative energy systems and
low environmental impact.
Computational analysis can help in the design phase, particularly
in the case of complex structures with centralized plant systems, by
comparing the data returned by the calculation model for different
design options.
Abstract: Attributes and methods are the basic contents of an
object-oriented class. The connectivity among these class members
and the relationship between the class and other classes play an
important role in determining the quality of an object-oriented
system. Class cohesion evaluates the degree of relatedness of class
attributes and methods, whereas class coupling refers to the degree to
which a class is related to other classes. Researchers have proposed
several class cohesion and class coupling measures. However, the
correlation between class coupling and class cohesion measures has
not been thoroughly studied. In this paper, using classes of three
open-source Java systems, we empirically investigate the correlation
between several measures of connectivity-based class cohesion and
coupling. Four connectivity-based cohesion measures and eight
coupling measures are considered in the empirical study. The
empirical study results show that class connectivity-based cohesion
and coupling internal quality attributes are inversely correlated. The
strength of the correlation depends highly on the cohesion and
coupling measurement approaches.
Abstract: The Malaysian government had consistently revived
its campaign for “Buy Malaysian Goods” from time to time. The
purpose of the campaign is to remind consumers to be ethnocentric
and patriotic when purchasing product and services. This is necessary
to ensure high demand for local products and services compared to
foreign products. However, the decline of domestic investment in
2012 has triggered concern for the Malaysian economy. Hence, this
study attempts to determine the drivers of actual purchasing behavior,
intention to purchase domestic products and ethnocentrism. The
study employs the cross-sectional primary data, self-administered on
household, selected using stratified random sampling in four
Malaysian regions. A nine factor driver of actual domestic purchasing
behavior (culture openness, conservatism, collectivism, patriotism,
control belief, interest in foreign travel, attitude, ethnocentrism and
intention) were measured utilizing 60 items, using 7-point Likertscale.
From 1000 questionnaires distributed, a sample of 486 were
returned representing 48.6 percent response rate. From the fit
generated structural model (SEM analysis), it was found that the
drivers of actual purchase behavior are collectivism, cultural
openness and patriotism; the drivers of intention to purchase
domestic product are attitude, control belief, collectivism and
conservatism; and drivers of ethnocentrism are cultural openness,
control belief, foreign travel and patriotism. It also shows that
Malaysian consumers scored high in ethnocentrism and patriotism.
The findings are discussed in the perspective of its implication to
Malaysian National Agenda.
Abstract: Enterococci are important inhabitants of the animal
intestine and are widely used in probiotic products. A probiotic strain
is expected to possess several desirable properties in order to exert
beneficial effects. Therefore, the objective of this study was to
isolate, characterize and identify Enterococcus sp. from chicken cecal
and fecal samples to determine potential probiotic properties.
Enterococci were isolated from chicken ceca and feces of thirty three
clinically healthy chickens from a local farm. In vitro studies were
performed to assess antibacterial activity of the isolated LAB (using
agar well diffusion and cell free supernatant broth technique against
Salmonella enterica serotype Enteritidis), survival in acidic
conditions, resistance to bile salts, and their survival during simulated
gastric juice conditions at pH 2.5. Isolates were identified by
biochemical carbohydrate fermentation patterns using an API 50
CHL kit and API ZYM kits and by sequenced 16S rDNA. An isolate
belonging to E. faecium species exhibited inhibitory effect against S.
enteritidis. This isolate producing a clear zone as large as 10.30 mm
or greater and was able to grow in the coculture medium and at the
same time, inhibited the growth S. enteritidis. In addition, E. faecium
exhibited significant resistance under highly acidic conditions at pH
2.5 for 8 h and survived well in bile salt at 0.2% for 24 h and showing
ability to survive in the presence of simulated gastric juice at pH 2.5.
Based on these results, E. faecium isolate fulfills some of the criteria
to be considered as a probiotic strain and therefore, could be used as a
feed additive with good potential for controlling S. Enteritidis in
chickens. However, in vivo studies are needed to determine the safety
of the strain.
Abstract: The development of allometric models is crucial to
accurate forest biomass/carbon stock assessment. The aim of this
study was to develop a set of biomass prediction models that will
enable the determination of total tree aboveground biomass for
savannah woodland area in Niger State, Nigeria. Based on the data
collected through biometric measurements of 1816 trees and
destructive sampling of 36 trees, five species specific and one site
specific models were developed. The sample size was distributed
equally between the five most dominant species in the study site
(Vitellaria paradoxa, Irvingia gabonensis, Parkia biglobosa,
Anogeissus leiocarpus, Pterocarpus erinaceous). Firstly, the
equations were developed for five individual species. Secondly these
five species were mixed and were used to develop an allometric
equation of mixed species. Overall, there was a strong positive
relationship between total tree biomass and the stem diameter. The
coefficient of determination (R2 values) ranging from 0.93 to 0.99 P
< 0.001 were realised for the models; with considerable low standard
error of the estimates (SEE) which confirms that the total tree above
ground biomass has a significant relationship with the dbh. F-test
values for the biomass prediction models were also significant at p
Abstract: The detection of moving objects from a video image
sequences is very important for object tracking, activity recognition,
and behavior understanding in video surveillance.
The most used approach for moving objects detection / tracking is
background subtraction algorithms. Many approaches have been
suggested for background subtraction. But, these are illumination
change sensitive and the solutions proposed to bypass this problem
are time consuming.
In this paper, we propose a robust yet computationally efficient
background subtraction approach and, mainly, focus on the ability to
detect moving objects on dynamic scenes, for possible applications in
complex and restricted access areas monitoring, where moving and
motionless persons must be reliably detected. It consists of three
main phases, establishing illumination changes invariance,
background/foreground modeling and morphological analysis for
noise removing.
We handle illumination changes using Contrast Limited Histogram
Equalization (CLAHE), which limits the intensity of each pixel to
user determined maximum. Thus, it mitigates the degradation due to
scene illumination changes and improves the visibility of the video
signal. Initially, the background and foreground images are extracted
from the video sequence. Then, the background and foreground
images are separately enhanced by applying CLAHE.
In order to form multi-modal backgrounds we model each channel
of a pixel as a mixture of K Gaussians (K=5) using Gaussian Mixture
Model (GMM). Finally, we post process the resulting binary
foreground mask using morphological erosion and dilation
transformations to remove possible noise.
For experimental test, we used a standard dataset to challenge the
efficiency and accuracy of the proposed method on a diverse set of
dynamic scenes.
Abstract: The concentrations of cadmium and lead in sewage
sludge samples were determined by Atomic Absorption
Spectrometric Method. Samples of sewage sludge were obtained
from three sewage treatment plants localised in Middle Region of
Libya (Misrata, Msallata and Tarhünah cities).
The results shows that, the mean levels of Cadmium for all regions
are ranges from 81 to 123.4 ppm and these values are higher than the
limitations for the international standard which are not registered
more than 50 ppm (dry weight) in USA, Egypt and the EU countries.
While, the lead concentrations are ranged from 8.0 to 189.2 ppm and
all values are within the standard limits which graduated between
(275–613) ppm.
Abstract: Previous studies on financial distress prediction choose
the conventional failing and non-failing dichotomy; however, the
distressed extent differs substantially among different financial
distress events. To solve the problem, “non-distressed”, “slightlydistressed”
and “reorganization and bankruptcy” are used in our article
to approximate the continuum of corporate financial health. This paper
explains different financial distress events using the two-stage method.
First, this investigation adopts firm-specific financial ratios, corporate
governance and market factors to measure the probability of various
financial distress events based on multinomial logit models.
Specifically, the bootstrapping simulation is performed to examine the
difference of estimated misclassifying cost (EMC). Second, this work
further applies macroeconomic factors to establish the credit cycle
index and determines the distressed cut-off indicator of the two-stage
models using such index. Two different models, one-stage and
two-stage prediction models are developed to forecast financial
distress, and the results acquired from different models are compared
with each other, and with the collected data. The findings show that the
one-stage model has the lower misclassification error rate than the
two-stage model. The one-stage model is more accurate than the
two-stage model.
Abstract: Electroencephalogram (EEG) is a noninvasive
technique that registers signals originating from the firing of neurons
in the brain. The Emotiv EEG Neuroheadset is a consumer product
comprised of 14 EEG channels and was used to record the reactions
of the neurons within the brain to two forms of stimuli in 10
participants. These stimuli consisted of auditory and visual formats
that provided directions of ‘right’ or ‘left.’ Participants were
instructed to raise their right or left arm in accordance with the
instruction given. A scenario in OpenViBE was generated to both
stimulate the participants while recording their data. In OpenViBE,
the Graz Motor BCI Stimulator algorithm was configured to govern
the duration and number of visual stimuli. Utilizing EEGLAB under
the cross platform MATLAB®, the electrodes most stimulated during
the study were defined. Data outputs from EEGLAB were analyzed
using IBM SPSS Statistics® Version 20. This aided in determining
the electrodes to use in the development of a brain-machine interface
(BMI) using real-time EEG signals from the Emotiv EEG
Neuroheadset. Signal processing and feature extraction were
accomplished via the Simulink® signal processing toolbox. An
Arduino™ Duemilanove microcontroller was used to link the Emotiv
EEG Neuroheadset and the right and left Mecha TE™ Hands.
Abstract: Paints are the most widely used methods of protection
against atmospheric corrosion of metals. The aim of this work was to
determine the protective performance of epoxy coating against sea
water before and after damage.
Investigations are conducted using stationary and non-stationary
electrochemical tools such as electrochemical impedance
spectroscopy has allowed us to characterize the protective qualities of
these films. The application of the EIS on our damaged in-situ
painting shows the existence of several capacitive loops which is an
indicator of the failure of our tested paint. Microscopic analysis
(micrograph) helped bring essential elements in understanding the
degradation of our paint condition and immersion training corrosion
products.
Abstract: Pedagogy has always been open to other disciplines
that reflect about the educational process (philosophy, sociology,
psychology, anthropology, technology, etc.). Its interdisciplinary
openness puts education, as the subject of pedagogy within a broader
context of the community, enabling the knowledge of other
disciplines to contribute to a better understanding of the fundamental
pedagogical notion of education. The purpose of pedagogy as a
science serves humans, strives towards humans, must be for humans,
and this is its ultimate goal. Humans are essentially dependent on
education, which is also considered as a category of humans’ being,
because through education an entire world develops in humans.
Anthropological assumptions of humans as "deficient beings" see the
solution in education, but they also indicate a wealth of shortcomings,
because they provide an opportunity for enrichment and formation of
culture, living and the self. In that context, this paper illustrates the
determination of pedagogy through an anthropological conception of
humans and the phenomenon of education. It presents a review of
anthropological ideas about education, by providing an analysis of
relevant literature dealing with the anthropological notion of humans,
which provides fruitful conditions for a pedagogical reconsideration
of education.
Abstract: Presently, it is necessary to ensure the sustainable
development of passenger and freight transport. Increasing
performance of road freight has had a negative impact to environment
and society. It is therefore necessary to increase the competitiveness
of intermodal transport, which is more environmentally friendly. The
study describes the effectiveness of logistical centers realization for
companies and society and research how the partial internalization of
external costs reflected in the efficient use of these centers and
increase the competitiveness of intermodal transport to road freight.
In our research, we use the method of comparative analysis and
market research to describe the advantages of logistic centers for their
users as well as for society as a whole. Method normal costing is used
for calculation infrastructure and total costs, method of conversion
costing for determine the external costs. We modelled total society
costs for road freight transport and inter modal transport chain (we
assumed that most of the traffic is carried by rail) with different
loading schemes for condition in the Slovak Republic. Our research
has shown that higher utilization of inter modal transport chain do
good not only for society, but for companies providing freight
services too. Increase in use of inter modal transport chain can bring
many benefits to society that do not bring direct immediate financial
return. They often bring the multiplier effects, such as greater use of
environmentally friendly transport mode and reduce the total society
costs.
Abstract: Lipases constitute one of the most important groups of
industrial enzymes that catalyze the hydrolysis of triacylglycerol to
glycerol and fatty acids. Muscarinic antagonist relieves smooth
muscle spasm of the gastrointestinal tract and effect on the
cardiovascular system. In this research the effect of a muscarinic
antagonist on the lipase activity of Pseudomonas aeruginosa was
studied. Lineweaver–Burk plot showed that the drug inhibited the
enzyme by competitive inhibition. The IC50 value (0.16 mM) and Ki
(0.03 mM) of the drug revealed the drug bound to enzyme with high
affinity. Determination of enzyme activity in various pH and
temperature showed that the maximum activity of lipase was at pH 8
and 60oC both in presence and absence of the drug.
Abstract: The objective of this study was to evaluate the
physical and chemical characteristics of Serra da Estrela cheese and
compare these results with those of the sensory analysis. For the
study were taken six samples of Serra da Estrela cheese produced
with 6 different ecotypes of thistle in a dairy situated in Penalva do
Castelo. The chemical properties evaluated were moisture content,
protein, fat, ash, chloride and pH; the physical properties studied
were color and texture; and finally a sensory evaluation was
undertaken. The results showed moisture varying in the range 40-
48%, protein in the range 15-20%, fat between 41-45%, ash between
3.9-5.0% and chlorides varying from 1.2 to 3.0%. The pH varied
from 4.8 to 5.4. The textural properties revealed that the crust
hardness is relatively low (maximum 7.3 N), although greater than
flesh firmness (maximum 1.7 N), and also that these cheeses are in
fact soft paste type, with measurable stickiness and intense
adhesiveness. The color analysis showed that the crust is relatively
light (L* over 50), and with a predominant yellow coloration (b*
around 20 or over) although with a slight greenish tone (a* negative).
The results of the sensory analysis did not show great variability for
most of the attributes measured, although some differences were
found in attributes such as crust thickness, crust uniformity, and
creamy flesh.
Abstract: Flours of wheat, chestnut, acorn and lupin were
evaluated in relation to phenolic compounds, antioxidant activity, and
oxalate content. At the chemical level the results show some
variability between samples by type of flour, and the sample of
chestnut flour presented the higher value of oxalate (0.00348
mg/100g) when compared to the other samples in the study.
Considering the content of phenolic compounds, the sample that
stood out was the acorn flour, having a high value of 0.812 g
AGE/100 g. All the samples presented intermediate content of
antioxidant activity and the sample that showed a slightly higher
value was the wheat flour with a value of 0.746 mM TRE/g sample.
Abstract: In this study, we compare the profiles of transitory
hybrid entrepreneurs and persistent hybrid entrepreneurs to determine
how they differ. Hybrid entrepreneurs (HEs) represent a significant
share of entrepreneurial activity yet little is known about them. We
define HEs as individuals who are active as entrepreneurs but do no
support themselves primarily by their enterprise. Persistent HEs
(PHEs) are not planning to transition to fulltime entrepreneurship
whereas transitory HEs (THEs) consider it probable. Our results
show that THEs and PHEs are quite similar in background. THEs are
more interested in increasing their turnover than PHEs, as expected,
but also emphasize self-fulfillment as a motive for entrepreneurship
more than PHEs. The clearest differences between THEs and PHEs
are found in their views on how well their immediate circle supports
full-time entrepreneurship, and their views of their own
entrepreneurial abilities and the market potential of their firm. Our
results support earlier arguments that hybrids should be considered
separately in research on entrepreneurial entry and self-employment.
Abstract: The paper deals with behaviour of the segment 50+ in
the financial market in the Czech Republic. This segment could be
said as the strong market power and it can be a crucial business
potential for financial business units. The main defined objective of
this paper is analysis of the customers´ behaviour of the segment 50-
60 years in the financial market in the Czech Republic and proposal
making of the suitable marketing approach to satisfy their demands in
the area of product, price, distribution and marketing communication
policy. This paper is based on data from one part of primary
marketing research. Paper determinates the basic problem areas as
well as definition of financial services marketing, defining the
primary research problem, hypothesis and primary research
methodology. Finally suitable marketing approach to selected sub
segment at age of 50-60 years is proposed according to marketing
research findings.